4 select ARCH_BINFMT_ELF_RANDOMIZE_PIE
5 select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
6 select ARCH_HAVE_CUSTOM_GPIO_H
7 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
8 select ARCH_WANT_IPC_PARSE_VERSION
9 select BUILDTIME_EXTABLE_SORT if MMU
10 select CPU_PM if (SUSPEND || CPU_IDLE)
11 select DCACHE_WORD_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && !CPU_BIG_ENDIAN && MMU
12 select GENERIC_ATOMIC64 if (CPU_V6 || !CPU_32v6K || !AEABI)
13 select GENERIC_CLOCKEVENTS_BROADCAST if SMP
14 select GENERIC_IRQ_PROBE
15 select GENERIC_IRQ_SHOW
16 select GENERIC_PCI_IOMAP
17 select GENERIC_SMP_IDLE_THREAD
18 select GENERIC_STRNCPY_FROM_USER
19 select GENERIC_STRNLEN_USER
20 select HARDIRQS_SW_RESEND
22 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL
24 select HAVE_ARCH_SECCOMP_FILTER
25 select HAVE_ARCH_TRACEHOOK
27 select HAVE_C_RECORDMCOUNT
28 select HAVE_DEBUG_KMEMLEAK
29 select HAVE_DMA_API_DEBUG
31 select HAVE_DMA_CONTIGUOUS if MMU
32 select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL)
33 select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)
34 select HAVE_FUNCTION_GRAPH_TRACER if (!THUMB2_KERNEL)
35 select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
36 select HAVE_GENERIC_DMA_COHERENT
37 select HAVE_GENERIC_HARDIRQS
38 select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7))
39 select HAVE_IDE if PCI || ISA || PCMCIA
40 select HAVE_KERNEL_GZIP
41 select HAVE_KERNEL_LZMA
42 select HAVE_KERNEL_LZO
44 select HAVE_KPROBES if !XIP_KERNEL
45 select HAVE_KRETPROBES if (HAVE_KPROBES)
47 select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
48 select HAVE_PERF_EVENTS
49 select HAVE_REGS_AND_STACK_ACCESS_API
50 select HAVE_SYSCALL_TRACEPOINTS
53 select PERF_USE_VMALLOC
55 select SYS_SUPPORTS_APM_EMULATION
56 select HAVE_MOD_ARCH_SPECIFIC if ARM_UNWIND
57 select MODULES_USE_ELF_REL
58 select CLONE_BACKWARDS
59 select OLD_SIGSUSPEND3
62 The ARM series is a line of low-power-consumption RISC chip designs
63 licensed by ARM Ltd and targeted at embedded applications and
64 handhelds such as the Compaq IPAQ. ARM-based PCs are no longer
65 manufactured, but legacy ARM-based PC hardware remains popular in
66 Europe. There is an ARM Linux project with a web page at
67 <http://www.arm.linux.org.uk/>.
69 config ARM_HAS_SG_CHAIN
72 config NEED_SG_DMA_LENGTH
75 config ARM_DMA_USE_IOMMU
77 select ARM_HAS_SG_CHAIN
78 select NEED_SG_DMA_LENGTH
82 config ARM_DMA_IOMMU_ALIGNMENT
83 int "Maximum PAGE_SIZE order of alignment for DMA IOMMU buffers"
87 DMA mapping framework by default aligns all buffers to the smallest
88 PAGE_SIZE order which is greater than or equal to the requested buffer
89 size. This works well for buffers up to a few hundreds kilobytes, but
90 for larger buffers it just a waste of address space. Drivers which has
91 relatively small addressing window (like 64Mib) might run out of
92 virtual space with just a few allocations.
94 With this parameter you can specify the maximum PAGE_SIZE order for
95 DMA IOMMU buffers. Larger buffers will be aligned only to this
96 specified order. The order is expressed as a power of two multiplied
104 config MIGHT_HAVE_PCI
107 config SYS_SUPPORTS_APM_EMULATION
115 select GENERIC_ALLOCATOR
126 The Extended Industry Standard Architecture (EISA) bus was
127 developed as an open alternative to the IBM MicroChannel bus.
129 The EISA bus provided some of the features of the IBM MicroChannel
130 bus while maintaining backward compatibility with cards made for
131 the older ISA bus. The EISA bus saw limited use between 1988 and
132 1995 when it was made obsolete by the PCI bus.
134 Say Y here if you are building a kernel for an EISA-based machine.
141 config STACKTRACE_SUPPORT
145 config HAVE_LATENCYTOP_SUPPORT
150 config LOCKDEP_SUPPORT
154 config TRACE_IRQFLAGS_SUPPORT
158 config RWSEM_GENERIC_SPINLOCK
162 config RWSEM_XCHGADD_ALGORITHM
165 config ARCH_HAS_ILOG2_U32
168 config ARCH_HAS_ILOG2_U64
171 config ARCH_HAS_CPUFREQ
174 Internal node to signify that the ARCH has CPUFREQ support
175 and that the relevant menu configurations are displayed for
178 config GENERIC_HWEIGHT
182 config GENERIC_CALIBRATE_DELAY
186 config ARCH_MAY_HAVE_PC_FDC
192 config NEED_DMA_MAP_STATE
195 config ARCH_HAS_DMA_SET_COHERENT_MASK
198 config GENERIC_ISA_DMA
204 config NEED_RET_TO_USER
212 default 0xffff0000 if MMU || CPU_HIGH_VECTOR
213 default DRAM_BASE if REMAP_VECTORS_TO_RAM
216 The base address of exception vectors.
218 config ARM_PATCH_PHYS_VIRT
219 bool "Patch physical to virtual translations at runtime" if EMBEDDED
221 depends on !XIP_KERNEL && MMU
222 depends on !ARCH_REALVIEW || !SPARSEMEM
224 Patch phys-to-virt and virt-to-phys translation functions at
225 boot and module load time according to the position of the
226 kernel in system memory.
228 This can only be used with non-XIP MMU kernels where the base
229 of physical memory is at a 16MB boundary.
231 Only disable this option if you know that you do not require
232 this feature (eg, building a kernel for a single machine) and
233 you need to shrink the kernel to the minimal size.
235 config NEED_MACH_GPIO_H
238 Select this when mach/gpio.h is required to provide special
239 definitions for this platform. The need for mach/gpio.h should
240 be avoided when possible.
242 config NEED_MACH_IO_H
245 Select this when mach/io.h is required to provide special
246 definitions for this platform. The need for mach/io.h should
247 be avoided when possible.
249 config NEED_MACH_MEMORY_H
252 Select this when mach/memory.h is required to provide special
253 definitions for this platform. The need for mach/memory.h should
254 be avoided when possible.
257 hex "Physical address of main memory" if MMU
258 depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
259 default DRAM_BASE if !MMU
261 Please provide the physical address corresponding to the
262 location of main memory in your system.
268 source "init/Kconfig"
270 source "kernel/Kconfig.freezer"
275 bool "MMU-based Paged Memory Management Support"
278 Select if you want MMU-based virtualised addressing space
279 support by paged memory management. If unsure, say 'Y'.
282 # The "ARM system type" choice list is ordered alphabetically by option
283 # text. Please add new entries in the option alphabetic order.
286 prompt "ARM system type"
287 default ARCH_VERSATILE if !MMU
288 default ARCH_MULTIPLATFORM if MMU
290 config ARCH_MULTIPLATFORM
291 bool "Allow multiple platforms to be selected"
293 select ARM_PATCH_PHYS_VIRT
296 select MULTI_IRQ_HANDLER
300 config ARCH_INTEGRATOR
301 bool "ARM Ltd. Integrator family"
302 select ARCH_HAS_CPUFREQ
305 select COMMON_CLK_VERSATILE
306 select GENERIC_CLOCKEVENTS
309 select MULTI_IRQ_HANDLER
310 select NEED_MACH_MEMORY_H
311 select PLAT_VERSATILE
313 select VERSATILE_FPGA_IRQ
315 Support for ARM's Integrator platform.
318 bool "ARM Ltd. RealView family"
319 select ARCH_WANT_OPTIONAL_GPIOLIB
321 select ARM_TIMER_SP804
323 select COMMON_CLK_VERSATILE
324 select GENERIC_CLOCKEVENTS
325 select GPIO_PL061 if GPIOLIB
327 select NEED_MACH_MEMORY_H
328 select PLAT_VERSATILE
329 select PLAT_VERSATILE_CLCD
331 This enables support for ARM Ltd RealView boards.
333 config ARCH_VERSATILE
334 bool "ARM Ltd. Versatile family"
335 select ARCH_WANT_OPTIONAL_GPIOLIB
337 select ARM_TIMER_SP804
340 select GENERIC_CLOCKEVENTS
341 select HAVE_MACH_CLKDEV
343 select PLAT_VERSATILE
344 select PLAT_VERSATILE_CLCD
345 select PLAT_VERSATILE_CLOCK
346 select VERSATILE_FPGA_IRQ
348 This enables support for ARM Ltd Versatile board.
352 select ARCH_REQUIRE_GPIOLIB
356 select NEED_MACH_GPIO_H
357 select NEED_MACH_IO_H if PCCARD
359 select PINCTRL_AT91 if USE_OF
361 This enables support for systems based on Atmel
362 AT91RM9200 and AT91SAM9* processors.
365 bool "Broadcom BCM2835 family"
366 select ARCH_REQUIRE_GPIOLIB
368 select ARM_ERRATA_411920
369 select ARM_TIMER_SP804
374 select GENERIC_CLOCKEVENTS
375 select MULTI_IRQ_HANDLER
377 select PINCTRL_BCM2835
381 This enables support for the Broadcom BCM2835 SoC. This SoC is
382 use in the Raspberry Pi, and Roku 2 devices.
385 bool "Cavium Networks CNS3XXX family"
388 select GENERIC_CLOCKEVENTS
389 select MIGHT_HAVE_CACHE_L2X0
390 select MIGHT_HAVE_PCI
391 select PCI_DOMAINS if PCI
393 Support for Cavium Networks CNS3XXX platform.
396 bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
397 select ARCH_REQUIRE_GPIOLIB
402 select GENERIC_CLOCKEVENTS
403 select MULTI_IRQ_HANDLER
404 select NEED_MACH_MEMORY_H
407 Support for Cirrus Logic 711x/721x/731x based boards.
410 bool "Cortina Systems Gemini"
411 select ARCH_REQUIRE_GPIOLIB
412 select ARCH_USES_GETTIMEOFFSET
415 Support for the Cortina Systems Gemini family SoCs
419 select ARCH_REQUIRE_GPIOLIB
422 select GENERIC_CLOCKEVENTS
423 select GENERIC_IRQ_CHIP
424 select MIGHT_HAVE_CACHE_L2X0
430 Support for CSR SiRFprimaII/Marco/Polo platforms
434 select ARCH_USES_GETTIMEOFFSET
437 select NEED_MACH_IO_H
438 select NEED_MACH_MEMORY_H
441 This is an evaluation board for the StrongARM processor available
442 from Digital. It has limited hardware on-board, including an
443 Ethernet interface, two PCMCIA sockets, two serial ports and a
448 select ARCH_HAS_HOLES_MEMORYMODEL
449 select ARCH_REQUIRE_GPIOLIB
450 select ARCH_USES_GETTIMEOFFSET
455 select NEED_MACH_MEMORY_H
457 This enables support for the Cirrus EP93xx series of CPUs.
459 config ARCH_FOOTBRIDGE
463 select GENERIC_CLOCKEVENTS
465 select NEED_MACH_IO_H if !MMU
466 select NEED_MACH_MEMORY_H
468 Support for systems based on the DC21285 companion chip
469 ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
472 bool "Freescale MXS-based"
473 select ARCH_REQUIRE_GPIOLIB
477 select GENERIC_CLOCKEVENTS
478 select HAVE_CLK_PREPARE
479 select MULTI_IRQ_HANDLER
484 Support for Freescale MXS-based family of processors
487 bool "Hilscher NetX based"
491 select GENERIC_CLOCKEVENTS
493 This enables support for systems based on the Hilscher NetX Soc
496 bool "Hynix HMS720x-based"
497 select ARCH_USES_GETTIMEOFFSET
501 This enables support for systems based on the Hynix HMS720x
506 select ARCH_SUPPORTS_MSI
508 select NEED_MACH_MEMORY_H
509 select NEED_RET_TO_USER
514 Support for Intel's IOP13XX (XScale) family of processors.
519 select ARCH_REQUIRE_GPIOLIB
521 select NEED_MACH_GPIO_H
522 select NEED_RET_TO_USER
526 Support for Intel's 80219 and IOP32X (XScale) family of
532 select ARCH_REQUIRE_GPIOLIB
534 select NEED_MACH_GPIO_H
535 select NEED_RET_TO_USER
539 Support for Intel's IOP33X (XScale) family of processors.
544 select ARCH_HAS_DMA_SET_COHERENT_MASK
545 select ARCH_REQUIRE_GPIOLIB
548 select DMABOUNCE if PCI
549 select GENERIC_CLOCKEVENTS
550 select MIGHT_HAVE_PCI
551 select NEED_MACH_IO_H
553 Support for Intel's IXP4XX (XScale) family of processors.
557 select ARCH_REQUIRE_GPIOLIB
559 select GENERIC_CLOCKEVENTS
560 select MIGHT_HAVE_PCI
563 select PLAT_ORION_LEGACY
564 select USB_ARCH_HAS_EHCI
566 Support for the Marvell Dove SoC 88AP510
569 bool "Marvell Kirkwood"
570 select ARCH_REQUIRE_GPIOLIB
572 select GENERIC_CLOCKEVENTS
576 select PINCTRL_KIRKWOOD
577 select PLAT_ORION_LEGACY
580 Support for the following Marvell Kirkwood series SoCs:
581 88F6180, 88F6192 and 88F6281.
584 bool "Marvell MV78xx0"
585 select ARCH_REQUIRE_GPIOLIB
587 select GENERIC_CLOCKEVENTS
589 select PLAT_ORION_LEGACY
591 Support for the following Marvell MV78xx0 series SoCs:
597 select ARCH_REQUIRE_GPIOLIB
599 select GENERIC_CLOCKEVENTS
601 select PLAT_ORION_LEGACY
603 Support for the following Marvell Orion 5x series SoCs:
604 Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182),
605 Orion-2 (5281), Orion-1-90 (6183).
608 bool "Marvell PXA168/910/MMP2"
610 select ARCH_REQUIRE_GPIOLIB
612 select GENERIC_ALLOCATOR
613 select GENERIC_CLOCKEVENTS
616 select NEED_MACH_GPIO_H
621 Support for Marvell's PXA168/PXA910(MMP) and MMP2 processor line.
624 bool "Micrel/Kendin KS8695"
625 select ARCH_REQUIRE_GPIOLIB
628 select GENERIC_CLOCKEVENTS
629 select NEED_MACH_MEMORY_H
631 Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
632 System-on-Chip devices.
635 bool "Nuvoton W90X900 CPU"
636 select ARCH_REQUIRE_GPIOLIB
640 select GENERIC_CLOCKEVENTS
642 Support for Nuvoton (Winbond logic dept.) ARM9 processor,
643 At present, the w90x900 has been renamed nuc900, regarding
644 the ARM series product line, you can login the following
645 link address to know more.
647 <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/
648 ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller>
652 select ARCH_REQUIRE_GPIOLIB
657 select GENERIC_CLOCKEVENTS
660 select USB_ARCH_HAS_OHCI
663 Support for the NXP LPC32XX family of processors
667 select ARCH_HAS_CPUFREQ
668 select ARCH_REQUIRE_GPIOLIB
673 select GENERIC_CLOCKEVENTS
676 select MIGHT_HAVE_CACHE_L2X0
680 This enables support for NVIDIA Tegra based systems (Tegra APX,
681 Tegra 6xx and Tegra 2 series).
684 bool "PXA2xx/PXA3xx-based"
686 select ARCH_HAS_CPUFREQ
688 select ARCH_REQUIRE_GPIOLIB
689 select ARM_CPU_SUSPEND if PM
693 select GENERIC_CLOCKEVENTS
696 select MULTI_IRQ_HANDLER
697 select NEED_MACH_GPIO_H
701 Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
705 select ARCH_REQUIRE_GPIOLIB
707 select GENERIC_CLOCKEVENTS
710 Support for Qualcomm MSM/QSD based systems. This runs on the
711 apps processor of the MSM/QSD and depends on a shared memory
712 interface to the modem processor which runs the baseband
713 stack and controls some vital subsystems
714 (clock and power control, etc).
717 bool "Renesas SH-Mobile / R-Mobile"
719 select GENERIC_CLOCKEVENTS
721 select HAVE_MACH_CLKDEV
723 select MIGHT_HAVE_CACHE_L2X0
724 select MULTI_IRQ_HANDLER
725 select NEED_MACH_MEMORY_H
728 select PM_GENERIC_DOMAINS if PM
731 Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
736 select ARCH_MAY_HAVE_PC_FDC
737 select ARCH_SPARSEMEM_ENABLE
738 select ARCH_USES_GETTIMEOFFSET
741 select HAVE_PATA_PLATFORM
743 select NEED_MACH_IO_H
744 select NEED_MACH_MEMORY_H
748 On the Acorn Risc-PC, Linux can support the internal IDE disk and
749 CD-ROM interface, serial and parallel port, and the floppy drive.
753 select ARCH_HAS_CPUFREQ
755 select ARCH_REQUIRE_GPIOLIB
756 select ARCH_SPARSEMEM_ENABLE
761 select GENERIC_CLOCKEVENTS
764 select NEED_MACH_GPIO_H
765 select NEED_MACH_MEMORY_H
768 Support for StrongARM 11x0 based boards.
771 bool "Samsung S3C24XX SoCs"
772 select ARCH_HAS_CPUFREQ
773 select ARCH_USES_GETTIMEOFFSET
776 select HAVE_S3C2410_I2C if I2C
777 select HAVE_S3C2410_WATCHDOG if WATCHDOG
778 select HAVE_S3C_RTC if RTC_CLASS
779 select NEED_MACH_GPIO_H
780 select NEED_MACH_IO_H
782 Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
783 and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
784 (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
785 Samsung SMDK2410 development board (and derivatives).
788 bool "Samsung S3C64XX"
789 select ARCH_HAS_CPUFREQ
790 select ARCH_REQUIRE_GPIOLIB
791 select ARCH_USES_GETTIMEOFFSET
796 select HAVE_S3C2410_I2C if I2C
797 select HAVE_S3C2410_WATCHDOG if WATCHDOG
799 select NEED_MACH_GPIO_H
803 select S3C_GPIO_TRACK
804 select SAMSUNG_CLKSRC
805 select SAMSUNG_GPIOLIB_4BIT
806 select SAMSUNG_IRQ_VIC_TIMER
807 select USB_ARCH_HAS_OHCI
809 Samsung S3C64XX series based systems
812 bool "Samsung S5P6440 S5P6450"
816 select GENERIC_CLOCKEVENTS
818 select HAVE_S3C2410_I2C if I2C
819 select HAVE_S3C2410_WATCHDOG if WATCHDOG
820 select HAVE_S3C_RTC if RTC_CLASS
821 select NEED_MACH_GPIO_H
823 Samsung S5P64X0 CPU based systems, such as the Samsung SMDK6440,
827 bool "Samsung S5PC100"
828 select ARCH_USES_GETTIMEOFFSET
832 select HAVE_S3C2410_I2C if I2C
833 select HAVE_S3C2410_WATCHDOG if WATCHDOG
834 select HAVE_S3C_RTC if RTC_CLASS
835 select NEED_MACH_GPIO_H
837 Samsung S5PC100 series based systems
840 bool "Samsung S5PV210/S5PC110"
841 select ARCH_HAS_CPUFREQ
842 select ARCH_HAS_HOLES_MEMORYMODEL
843 select ARCH_SPARSEMEM_ENABLE
847 select GENERIC_CLOCKEVENTS
849 select HAVE_S3C2410_I2C if I2C
850 select HAVE_S3C2410_WATCHDOG if WATCHDOG
851 select HAVE_S3C_RTC if RTC_CLASS
852 select NEED_MACH_GPIO_H
853 select NEED_MACH_MEMORY_H
855 Samsung S5PV210/S5PC110 series based systems
858 bool "Samsung EXYNOS"
859 select ARCH_HAS_CPUFREQ
860 select ARCH_HAS_HOLES_MEMORYMODEL
861 select ARCH_SPARSEMEM_ENABLE
864 select GENERIC_CLOCKEVENTS
866 select HAVE_S3C2410_I2C if I2C
867 select HAVE_S3C2410_WATCHDOG if WATCHDOG
868 select HAVE_S3C_RTC if RTC_CLASS
869 select NEED_MACH_GPIO_H
870 select NEED_MACH_MEMORY_H
872 Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5)
876 select ARCH_USES_GETTIMEOFFSET
880 select NEED_MACH_MEMORY_H
885 Support for the StrongARM based Digital DNARD machine, also known
886 as "Shark" (<http://www.shark-linux.de/shark.html>).
889 bool "ST-Ericsson U300 Series"
891 select ARCH_REQUIRE_GPIOLIB
893 select ARM_PATCH_PHYS_VIRT
899 select GENERIC_CLOCKEVENTS
903 Support for ST-Ericsson U300 series mobile platforms.
906 bool "ST-Ericsson U8500 Series"
908 select ARCH_HAS_CPUFREQ
909 select ARCH_REQUIRE_GPIOLIB
913 select GENERIC_CLOCKEVENTS
915 select MIGHT_HAVE_CACHE_L2X0
918 Support for ST-Ericsson's Ux500 architecture
921 bool "STMicroelectronics Nomadik"
922 select ARCH_REQUIRE_GPIOLIB
925 select CLKSRC_NOMADIK_MTU
928 select GENERIC_CLOCKEVENTS
929 select MIGHT_HAVE_CACHE_L2X0
932 select PINCTRL_STN8815
935 Support for the Nomadik platform by ST-Ericsson
939 select ARCH_HAS_CPUFREQ
940 select ARCH_REQUIRE_GPIOLIB
945 select GENERIC_CLOCKEVENTS
948 Support for ST's SPEAr platform (SPEAr3xx, SPEAr6xx and SPEAr13xx).
952 select ARCH_HAS_HOLES_MEMORYMODEL
953 select ARCH_REQUIRE_GPIOLIB
955 select GENERIC_ALLOCATOR
956 select GENERIC_CLOCKEVENTS
957 select GENERIC_IRQ_CHIP
959 select NEED_MACH_GPIO_H
963 Support for TI's DaVinci platform.
968 select ARCH_HAS_CPUFREQ
969 select ARCH_HAS_HOLES_MEMORYMODEL
971 select ARCH_REQUIRE_GPIOLIB
974 select GENERIC_CLOCKEVENTS
975 select GENERIC_IRQ_CHIP
979 select NEED_MACH_IO_H if PCCARD
980 select NEED_MACH_MEMORY_H
982 Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
986 menu "Multiple platform selection"
987 depends on ARCH_MULTIPLATFORM
989 comment "CPU Core family selection"
992 bool "ARMv4 based platforms (FA526, StrongARM)"
993 depends on !ARCH_MULTI_V6_V7
994 select ARCH_MULTI_V4_V5
996 config ARCH_MULTI_V4T
997 bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
998 depends on !ARCH_MULTI_V6_V7
999 select ARCH_MULTI_V4_V5
1001 config ARCH_MULTI_V5
1002 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
1003 depends on !ARCH_MULTI_V6_V7
1004 select ARCH_MULTI_V4_V5
1006 config ARCH_MULTI_V4_V5
1009 config ARCH_MULTI_V6
1010 bool "ARMv6 based platforms (ARM11)"
1011 select ARCH_MULTI_V6_V7
1014 config ARCH_MULTI_V7
1015 bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
1017 select ARCH_MULTI_V6_V7
1018 select ARCH_VEXPRESS
1021 config ARCH_MULTI_V6_V7
1024 config ARCH_MULTI_CPU_AUTO
1025 def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
1026 select ARCH_MULTI_V5
1031 # This is sorted alphabetically by mach-* pathname. However, plat-*
1032 # Kconfigs may be included either alphabetically (according to the
1033 # plat- suffix) or along side the corresponding mach-* source.
1035 source "arch/arm/mach-mvebu/Kconfig"
1037 source "arch/arm/mach-at91/Kconfig"
1039 source "arch/arm/mach-bcm/Kconfig"
1041 source "arch/arm/mach-clps711x/Kconfig"
1043 source "arch/arm/mach-cns3xxx/Kconfig"
1045 source "arch/arm/mach-davinci/Kconfig"
1047 source "arch/arm/mach-dove/Kconfig"
1049 source "arch/arm/mach-ep93xx/Kconfig"
1051 source "arch/arm/mach-footbridge/Kconfig"
1053 source "arch/arm/mach-gemini/Kconfig"
1055 source "arch/arm/mach-h720x/Kconfig"
1057 source "arch/arm/mach-highbank/Kconfig"
1059 source "arch/arm/mach-integrator/Kconfig"
1061 source "arch/arm/mach-iop32x/Kconfig"
1063 source "arch/arm/mach-iop33x/Kconfig"
1065 source "arch/arm/mach-iop13xx/Kconfig"
1067 source "arch/arm/mach-ixp4xx/Kconfig"
1069 source "arch/arm/mach-kirkwood/Kconfig"
1071 source "arch/arm/mach-ks8695/Kconfig"
1073 source "arch/arm/mach-msm/Kconfig"
1075 source "arch/arm/mach-mv78xx0/Kconfig"
1077 source "arch/arm/mach-imx/Kconfig"
1079 source "arch/arm/mach-mxs/Kconfig"
1081 source "arch/arm/mach-netx/Kconfig"
1083 source "arch/arm/mach-nomadik/Kconfig"
1085 source "arch/arm/plat-omap/Kconfig"
1087 source "arch/arm/mach-omap1/Kconfig"
1089 source "arch/arm/mach-omap2/Kconfig"
1091 source "arch/arm/mach-orion5x/Kconfig"
1093 source "arch/arm/mach-picoxcell/Kconfig"
1095 source "arch/arm/mach-pxa/Kconfig"
1096 source "arch/arm/plat-pxa/Kconfig"
1098 source "arch/arm/mach-mmp/Kconfig"
1100 source "arch/arm/mach-realview/Kconfig"
1102 source "arch/arm/mach-sa1100/Kconfig"
1104 source "arch/arm/plat-samsung/Kconfig"
1106 source "arch/arm/mach-socfpga/Kconfig"
1108 source "arch/arm/plat-spear/Kconfig"
1110 source "arch/arm/mach-s3c24xx/Kconfig"
1113 source "arch/arm/mach-s3c64xx/Kconfig"
1116 source "arch/arm/mach-s5p64x0/Kconfig"
1118 source "arch/arm/mach-s5pc100/Kconfig"
1120 source "arch/arm/mach-s5pv210/Kconfig"
1122 source "arch/arm/mach-exynos/Kconfig"
1124 source "arch/arm/mach-shmobile/Kconfig"
1126 source "arch/arm/mach-sunxi/Kconfig"
1128 source "arch/arm/mach-prima2/Kconfig"
1130 source "arch/arm/mach-tegra/Kconfig"
1132 source "arch/arm/mach-u300/Kconfig"
1134 source "arch/arm/mach-ux500/Kconfig"
1136 source "arch/arm/mach-versatile/Kconfig"
1138 source "arch/arm/mach-vexpress/Kconfig"
1139 source "arch/arm/plat-versatile/Kconfig"
1141 source "arch/arm/mach-virt/Kconfig"
1143 source "arch/arm/mach-vt8500/Kconfig"
1145 source "arch/arm/mach-w90x900/Kconfig"
1147 source "arch/arm/mach-zynq/Kconfig"
1149 # Definitions to make life easier
1155 select GENERIC_CLOCKEVENTS
1161 select GENERIC_IRQ_CHIP
1164 config PLAT_ORION_LEGACY
1171 config PLAT_VERSATILE
1174 config ARM_TIMER_SP804
1177 select HAVE_SCHED_CLOCK
1179 source arch/arm/mm/Kconfig
1183 default 16 if ARCH_EP93XX
1187 bool "Enable iWMMXt support"
1188 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4
1189 default y if PXA27x || PXA3xx || ARCH_MMP
1191 Enable support for iWMMXt context switching at run time if
1192 running on a CPU that supports it.
1196 depends on CPU_XSCALE
1199 config MULTI_IRQ_HANDLER
1202 Allow each machine to specify it's own IRQ handler at run time.
1205 source "arch/arm/Kconfig-nommu"
1208 config ARM_ERRATA_326103
1209 bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory"
1212 Executing a SWP instruction to read-only memory does not set bit 11
1213 of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to
1214 treat the access as a read, preventing a COW from occurring and
1215 causing the faulting task to livelock.
1217 config ARM_ERRATA_411920
1218 bool "ARM errata: Invalidation of the Instruction Cache operation can fail"
1219 depends on CPU_V6 || CPU_V6K
1221 Invalidation of the Instruction Cache operation can
1222 fail. This erratum is present in 1136 (before r1p4), 1156 and 1176.
1223 It does not affect the MPCore. This option enables the ARM Ltd.
1224 recommended workaround.
1226 config ARM_ERRATA_430973
1227 bool "ARM errata: Stale prediction on replaced interworking branch"
1230 This option enables the workaround for the 430973 Cortex-A8
1231 (r1p0..r1p2) erratum. If a code sequence containing an ARM/Thumb
1232 interworking branch is replaced with another code sequence at the
1233 same virtual address, whether due to self-modifying code or virtual
1234 to physical address re-mapping, Cortex-A8 does not recover from the
1235 stale interworking branch prediction. This results in Cortex-A8
1236 executing the new code sequence in the incorrect ARM or Thumb state.
1237 The workaround enables the BTB/BTAC operations by setting ACTLR.IBE
1238 and also flushes the branch target cache at every context switch.
1239 Note that setting specific bits in the ACTLR register may not be
1240 available in non-secure mode.
1242 config ARM_ERRATA_458693
1243 bool "ARM errata: Processor deadlock when a false hazard is created"
1245 depends on !ARCH_MULTIPLATFORM
1247 This option enables the workaround for the 458693 Cortex-A8 (r2p0)
1248 erratum. For very specific sequences of memory operations, it is
1249 possible for a hazard condition intended for a cache line to instead
1250 be incorrectly associated with a different cache line. This false
1251 hazard might then cause a processor deadlock. The workaround enables
1252 the L1 caching of the NEON accesses and disables the PLD instruction
1253 in the ACTLR register. Note that setting specific bits in the ACTLR
1254 register may not be available in non-secure mode.
1256 config ARM_ERRATA_460075
1257 bool "ARM errata: Data written to the L2 cache can be overwritten with stale data"
1259 depends on !ARCH_MULTIPLATFORM
1261 This option enables the workaround for the 460075 Cortex-A8 (r2p0)
1262 erratum. Any asynchronous access to the L2 cache may encounter a
1263 situation in which recent store transactions to the L2 cache are lost
1264 and overwritten with stale memory contents from external memory. The
1265 workaround disables the write-allocate mode for the L2 cache via the
1266 ACTLR register. Note that setting specific bits in the ACTLR register
1267 may not be available in non-secure mode.
1269 config ARM_ERRATA_742230
1270 bool "ARM errata: DMB operation may be faulty"
1271 depends on CPU_V7 && SMP
1272 depends on !ARCH_MULTIPLATFORM
1274 This option enables the workaround for the 742230 Cortex-A9
1275 (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction
1276 between two write operations may not ensure the correct visibility
1277 ordering of the two writes. This workaround sets a specific bit in
1278 the diagnostic register of the Cortex-A9 which causes the DMB
1279 instruction to behave as a DSB, ensuring the correct behaviour of
1282 config ARM_ERRATA_742231
1283 bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption"
1284 depends on CPU_V7 && SMP
1285 depends on !ARCH_MULTIPLATFORM
1287 This option enables the workaround for the 742231 Cortex-A9
1288 (r2p0..r2p2) erratum. Under certain conditions, specific to the
1289 Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode,
1290 accessing some data located in the same cache line, may get corrupted
1291 data due to bad handling of the address hazard when the line gets
1292 replaced from one of the CPUs at the same time as another CPU is
1293 accessing it. This workaround sets specific bits in the diagnostic
1294 register of the Cortex-A9 which reduces the linefill issuing
1295 capabilities of the processor.
1297 config PL310_ERRATA_588369
1298 bool "PL310 errata: Clean & Invalidate maintenance operations do not invalidate clean lines"
1299 depends on CACHE_L2X0
1301 The PL310 L2 cache controller implements three types of Clean &
1302 Invalidate maintenance operations: by Physical Address
1303 (offset 0x7F0), by Index/Way (0x7F8) and by Way (0x7FC).
1304 They are architecturally defined to behave as the execution of a
1305 clean operation followed immediately by an invalidate operation,
1306 both performing to the same memory location. This functionality
1307 is not correctly implemented in PL310 as clean lines are not
1308 invalidated as a result of these operations.
1310 config ARM_ERRATA_720789
1311 bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID"
1314 This option enables the workaround for the 720789 Cortex-A9 (prior to
1315 r2p0) erratum. A faulty ASID can be sent to the other CPUs for the
1316 broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS.
1317 As a consequence of this erratum, some TLB entries which should be
1318 invalidated are not, resulting in an incoherency in the system page
1319 tables. The workaround changes the TLB flushing routines to invalidate
1320 entries regardless of the ASID.
1322 config PL310_ERRATA_727915
1323 bool "PL310 errata: Background Clean & Invalidate by Way operation can cause data corruption"
1324 depends on CACHE_L2X0
1326 PL310 implements the Clean & Invalidate by Way L2 cache maintenance
1327 operation (offset 0x7FC). This operation runs in background so that
1328 PL310 can handle normal accesses while it is in progress. Under very
1329 rare circumstances, due to this erratum, write data can be lost when
1330 PL310 treats a cacheable write transaction during a Clean &
1331 Invalidate by Way operation.
1333 config ARM_ERRATA_743622
1334 bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
1336 depends on !ARCH_MULTIPLATFORM
1338 This option enables the workaround for the 743622 Cortex-A9
1339 (r2p*) erratum. Under very rare conditions, a faulty
1340 optimisation in the Cortex-A9 Store Buffer may lead to data
1341 corruption. This workaround sets a specific bit in the diagnostic
1342 register of the Cortex-A9 which disables the Store Buffer
1343 optimisation, preventing the defect from occurring. This has no
1344 visible impact on the overall performance or power consumption of the
1347 config ARM_ERRATA_751472
1348 bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
1350 depends on !ARCH_MULTIPLATFORM
1352 This option enables the workaround for the 751472 Cortex-A9 (prior
1353 to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
1354 completion of a following broadcasted operation if the second
1355 operation is received by a CPU before the ICIALLUIS has completed,
1356 potentially leading to corrupted entries in the cache or TLB.
1358 config PL310_ERRATA_753970
1359 bool "PL310 errata: cache sync operation may be faulty"
1360 depends on CACHE_PL310
1362 This option enables the workaround for the 753970 PL310 (r3p0) erratum.
1364 Under some condition the effect of cache sync operation on
1365 the store buffer still remains when the operation completes.
1366 This means that the store buffer is always asked to drain and
1367 this prevents it from merging any further writes. The workaround
1368 is to replace the normal offset of cache sync operation (0x730)
1369 by another offset targeting an unmapped PL310 register 0x740.
1370 This has the same effect as the cache sync operation: store buffer
1371 drain and waiting for all buffers empty.
1373 config ARM_ERRATA_754322
1374 bool "ARM errata: possible faulty MMU translations following an ASID switch"
1377 This option enables the workaround for the 754322 Cortex-A9 (r2p*,
1378 r3p*) erratum. A speculative memory access may cause a page table walk
1379 which starts prior to an ASID switch but completes afterwards. This
1380 can populate the micro-TLB with a stale entry which may be hit with
1381 the new ASID. This workaround places two dsb instructions in the mm
1382 switching code so that no page table walks can cross the ASID switch.
1384 config ARM_ERRATA_754327
1385 bool "ARM errata: no automatic Store Buffer drain"
1386 depends on CPU_V7 && SMP
1388 This option enables the workaround for the 754327 Cortex-A9 (prior to
1389 r2p0) erratum. The Store Buffer does not have any automatic draining
1390 mechanism and therefore a livelock may occur if an external agent
1391 continuously polls a memory location waiting to observe an update.
1392 This workaround defines cpu_relax() as smp_mb(), preventing correctly
1393 written polling loops from denying visibility of updates to memory.
1395 config ARM_ERRATA_364296
1396 bool "ARM errata: Possible cache data corruption with hit-under-miss enabled"
1397 depends on CPU_V6 && !SMP
1399 This options enables the workaround for the 364296 ARM1136
1400 r0p2 erratum (possible cache data corruption with
1401 hit-under-miss enabled). It sets the undocumented bit 31 in
1402 the auxiliary control register and the FI bit in the control
1403 register, thus disabling hit-under-miss without putting the
1404 processor into full low interrupt latency mode. ARM11MPCore
1407 config ARM_ERRATA_764369
1408 bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
1409 depends on CPU_V7 && SMP
1411 This option enables the workaround for erratum 764369
1412 affecting Cortex-A9 MPCore with two or more processors (all
1413 current revisions). Under certain timing circumstances, a data
1414 cache line maintenance operation by MVA targeting an Inner
1415 Shareable memory region may fail to proceed up to either the
1416 Point of Coherency or to the Point of Unification of the
1417 system. This workaround adds a DSB instruction before the
1418 relevant cache maintenance functions and sets a specific bit
1419 in the diagnostic control register of the SCU.
1421 config PL310_ERRATA_769419
1422 bool "PL310 errata: no automatic Store Buffer drain"
1423 depends on CACHE_L2X0
1425 On revisions of the PL310 prior to r3p2, the Store Buffer does
1426 not automatically drain. This can cause normal, non-cacheable
1427 writes to be retained when the memory system is idle, leading
1428 to suboptimal I/O performance for drivers using coherent DMA.
1429 This option adds a write barrier to the cpu_idle loop so that,
1430 on systems with an outer cache, the store buffer is drained
1433 config ARM_ERRATA_775420
1434 bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
1437 This option enables the workaround for the 775420 Cortex-A9 (r2p2,
1438 r2p6,r2p8,r2p10,r3p0) erratum. In case a date cache maintenance
1439 operation aborts with MMU exception, it might cause the processor
1440 to deadlock. This workaround puts DSB before executing ISB if
1441 an abort may occur on cache maintenance.
1445 source "arch/arm/common/Kconfig"
1455 Find out whether you have ISA slots on your motherboard. ISA is the
1456 name of a bus system, i.e. the way the CPU talks to the other stuff
1457 inside your box. Other bus systems are PCI, EISA, MicroChannel
1458 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
1459 newer boards don't support it. If you have ISA, say Y, otherwise N.
1461 # Select ISA DMA controller support
1466 # Select ISA DMA interface
1471 bool "PCI support" if MIGHT_HAVE_PCI
1473 Find out whether you have a PCI motherboard. PCI is the name of a
1474 bus system, i.e. the way the CPU talks to the other stuff inside
1475 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
1476 VESA. If you have PCI, say Y, otherwise N.
1482 config PCI_NANOENGINE
1483 bool "BSE nanoEngine PCI support"
1484 depends on SA1100_NANOENGINE
1486 Enable PCI on the BSE nanoEngine board.
1491 # Select the host bridge type
1492 config PCI_HOST_VIA82C505
1494 depends on PCI && ARCH_SHARK
1497 config PCI_HOST_ITE8152
1499 depends on PCI && MACH_ARMCORE
1503 source "drivers/pci/Kconfig"
1505 source "drivers/pcmcia/Kconfig"
1509 menu "Kernel Features"
1514 This option should be selected by machines which have an SMP-
1517 The only effect of this option is to make the SMP-related
1518 options available to the user for configuration.
1521 bool "Symmetric Multi-Processing"
1522 depends on CPU_V6K || CPU_V7
1523 depends on GENERIC_CLOCKEVENTS
1526 select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
1527 select USE_GENERIC_SMP_HELPERS
1529 This enables support for systems with more than one CPU. If you have
1530 a system with only one CPU, like most personal computers, say N. If
1531 you have a system with more than one CPU, say Y.
1533 If you say N here, the kernel will run on single and multiprocessor
1534 machines, but will use only one CPU of a multiprocessor machine. If
1535 you say Y here, the kernel will run on many, but not all, single
1536 processor machines. On a single processor machine, the kernel will
1537 run faster if you say N here.
1539 See also <file:Documentation/x86/i386/IO-APIC.txt>,
1540 <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
1541 <http://tldp.org/HOWTO/SMP-HOWTO.html>.
1543 If you don't know what to do here, say N.
1546 bool "Allow booting SMP kernel on uniprocessor systems (EXPERIMENTAL)"
1547 depends on SMP && !XIP_KERNEL
1550 SMP kernels contain instructions which fail on non-SMP processors.
1551 Enabling this option allows the kernel to modify itself to make
1552 these instructions safe. Disabling it allows about 1K of space
1555 If you don't know what to do here, say Y.
1557 config ARM_CPU_TOPOLOGY
1558 bool "Support cpu topology definition"
1559 depends on SMP && CPU_V7
1562 Support ARM cpu topology definition. The MPIDR register defines
1563 affinity between processors which is then used to describe the cpu
1564 topology of an ARM System.
1567 bool "Multi-core scheduler support"
1568 depends on ARM_CPU_TOPOLOGY
1570 Multi-core scheduler support improves the CPU scheduler's decision
1571 making when dealing with multi-core CPU chips at a cost of slightly
1572 increased overhead in some places. If unsure say N here.
1575 bool "SMT scheduler support"
1576 depends on ARM_CPU_TOPOLOGY
1578 Improves the CPU scheduler's decision making when dealing with
1579 MultiThreading at a cost of slightly increased overhead in some
1580 places. If unsure say N here.
1585 This option enables support for the ARM system coherency unit
1587 config HAVE_ARM_ARCH_TIMER
1588 bool "Architected timer support"
1590 select ARM_ARCH_TIMER
1592 This option enables support for the ARM architected timer
1598 This options enables support for the ARM timer and watchdog unit
1601 prompt "Memory split"
1604 Select the desired split between kernel and user memory.
1606 If you are not absolutely sure what you are doing, leave this
1610 bool "3G/1G user/kernel split"
1612 bool "2G/2G user/kernel split"
1614 bool "1G/3G user/kernel split"
1619 default 0x40000000 if VMSPLIT_1G
1620 default 0x80000000 if VMSPLIT_2G
1624 int "Maximum number of CPUs (2-32)"
1630 bool "Support for hot-pluggable CPUs"
1631 depends on SMP && HOTPLUG
1633 Say Y here to experiment with turning CPUs off and on. CPUs
1634 can be controlled through /sys/devices/system/cpu.
1637 bool "Support for the ARM Power State Coordination Interface (PSCI)"
1640 Say Y here if you want Linux to communicate with system firmware
1641 implementing the PSCI specification for CPU-centric power
1642 management operations described in ARM document number ARM DEN
1643 0022A ("Power State Coordination Interface System Software on
1647 bool "Use local timer interrupts"
1650 select HAVE_ARM_TWD if (!ARCH_MSM_SCORPIONMP && !EXYNOS4_MCT)
1652 Enable support for local timers on SMP platforms, rather then the
1653 legacy IPI broadcast method. Local timers allows the system
1654 accounting to be spread across the timer interval, preventing a
1655 "thundering herd" at every timer tick.
1657 # The GPIO number here must be sorted by descending number. In case of
1658 # a multiplatform kernel, we just want the highest value required by the
1659 # selected platforms.
1662 default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
1663 default 512 if SOC_OMAP5
1664 default 355 if ARCH_U8500
1665 default 288 if ARCH_VT8500 || ARCH_SUNXI
1666 default 264 if MACH_H4700
1669 Maximum number of GPIOs in the system.
1671 If unsure, leave the default value.
1673 source kernel/Kconfig.preempt
1677 default 200 if ARCH_EBSA110 || ARCH_S3C24XX || ARCH_S5P64X0 || \
1678 ARCH_S5PV210 || ARCH_EXYNOS4
1679 default AT91_TIMER_HZ if ARCH_AT91
1680 default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE
1684 def_bool HIGH_RES_TIMERS
1686 config THUMB2_KERNEL
1687 bool "Compile the kernel in Thumb-2 mode"
1688 depends on CPU_V7 && !CPU_V6 && !CPU_V6K
1690 select ARM_ASM_UNIFIED
1693 By enabling this option, the kernel will be compiled in
1694 Thumb-2 mode. A compiler/assembler that understand the unified
1695 ARM-Thumb syntax is needed.
1699 config THUMB2_AVOID_R_ARM_THM_JUMP11
1700 bool "Work around buggy Thumb-2 short branch relocations in gas"
1701 depends on THUMB2_KERNEL && MODULES
1704 Various binutils versions can resolve Thumb-2 branches to
1705 locally-defined, preemptible global symbols as short-range "b.n"
1706 branch instructions.
1708 This is a problem, because there's no guarantee the final
1709 destination of the symbol, or any candidate locations for a
1710 trampoline, are within range of the branch. For this reason, the
1711 kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
1712 relocation in modules at all, and it makes little sense to add
1715 The symptom is that the kernel fails with an "unsupported
1716 relocation" error when loading some modules.
1718 Until fixed tools are available, passing
1719 -fno-optimize-sibling-calls to gcc should prevent gcc generating
1720 code which hits this problem, at the cost of a bit of extra runtime
1721 stack usage in some cases.
1723 The problem is described in more detail at:
1724 https://bugs.launchpad.net/binutils-linaro/+bug/725126
1726 Only Thumb-2 kernels are affected.
1728 Unless you are sure your tools don't have this problem, say Y.
1730 config ARM_ASM_UNIFIED
1734 bool "Use the ARM EABI to compile the kernel"
1736 This option allows for the kernel to be compiled using the latest
1737 ARM ABI (aka EABI). This is only useful if you are using a user
1738 space environment that is also compiled with EABI.
1740 Since there are major incompatibilities between the legacy ABI and
1741 EABI, especially with regard to structure member alignment, this
1742 option also changes the kernel syscall calling convention to
1743 disambiguate both ABIs and allow for backward compatibility support
1744 (selected with CONFIG_OABI_COMPAT).
1746 To use this you need GCC version 4.0.0 or later.
1749 bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
1750 depends on AEABI && !THUMB2_KERNEL
1753 This option preserves the old syscall interface along with the
1754 new (ARM EABI) one. It also provides a compatibility layer to
1755 intercept syscalls that have structure arguments which layout
1756 in memory differs between the legacy ABI and the new ARM EABI
1757 (only for non "thumb" binaries). This option adds a tiny
1758 overhead to all syscalls and produces a slightly larger kernel.
1759 If you know you'll be using only pure EABI user space then you
1760 can say N here. If this option is not selected and you attempt
1761 to execute a legacy ABI binary then the result will be
1762 UNPREDICTABLE (in fact it can be predicted that it won't work
1763 at all). If in doubt say Y.
1765 config ARCH_HAS_HOLES_MEMORYMODEL
1768 config ARCH_SPARSEMEM_ENABLE
1771 config ARCH_SPARSEMEM_DEFAULT
1772 def_bool ARCH_SPARSEMEM_ENABLE
1774 config ARCH_SELECT_MEMORY_MODEL
1775 def_bool ARCH_SPARSEMEM_ENABLE
1777 config HAVE_ARCH_PFN_VALID
1778 def_bool ARCH_HAS_HOLES_MEMORYMODEL || !SPARSEMEM
1781 bool "High Memory Support"
1784 The address space of ARM processors is only 4 Gigabytes large
1785 and it has to accommodate user address space, kernel address
1786 space as well as some memory mapped IO. That means that, if you
1787 have a large amount of physical memory and/or IO, not all of the
1788 memory can be "permanently mapped" by the kernel. The physical
1789 memory that is not permanently mapped is called "high memory".
1791 Depending on the selected kernel/user memory split, minimum
1792 vmalloc space and actual amount of RAM, you may not need this
1793 option which should result in a slightly faster kernel.
1798 bool "Allocate 2nd-level pagetables from highmem"
1801 config HW_PERF_EVENTS
1802 bool "Enable hardware performance counter support for perf events"
1803 depends on PERF_EVENTS
1806 Enable hardware performance counter support for perf events. If
1807 disabled, perf events will use software events only.
1811 config FORCE_MAX_ZONEORDER
1812 int "Maximum zone order" if ARCH_SHMOBILE
1813 range 11 64 if ARCH_SHMOBILE
1814 default "12" if SOC_AM33XX
1815 default "9" if SA1111
1818 The kernel memory allocator divides physically contiguous memory
1819 blocks into "zones", where each zone is a power of two number of
1820 pages. This option selects the largest power of two that the kernel
1821 keeps in the memory allocator. If you need to allocate very large
1822 blocks of physically contiguous memory, then you may need to
1823 increase this value.
1825 This config option is actually maximum order plus one. For example,
1826 a value of 11 means that the largest free memory block is 2^10 pages.
1828 config ALIGNMENT_TRAP
1830 depends on CPU_CP15_MMU
1831 default y if !ARCH_EBSA110
1832 select HAVE_PROC_CPU if PROC_FS
1834 ARM processors cannot fetch/store information which is not
1835 naturally aligned on the bus, i.e., a 4 byte fetch must start at an
1836 address divisible by 4. On 32-bit ARM processors, these non-aligned
1837 fetch/store instructions will be emulated in software if you say
1838 here, which has a severe performance impact. This is necessary for
1839 correct operation of some network protocols. With an IP-only
1840 configuration it is safe to say N, otherwise say Y.
1842 config UACCESS_WITH_MEMCPY
1843 bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()"
1845 default y if CPU_FEROCEON
1847 Implement faster copy_to_user and clear_user methods for CPU
1848 cores where a 8-word STM instruction give significantly higher
1849 memory write throughput than a sequence of individual 32bit stores.
1851 A possible side effect is a slight increase in scheduling latency
1852 between threads sharing the same address space if they invoke
1853 such copy operations with large buffers.
1855 However, if the CPU data cache is using a write-allocate mode,
1856 this option is unlikely to provide any performance gain.
1860 prompt "Enable seccomp to safely compute untrusted bytecode"
1862 This kernel feature is useful for number crunching applications
1863 that may need to compute untrusted bytecode during their
1864 execution. By using pipes or other transports made available to
1865 the process as file descriptors supporting the read/write
1866 syscalls, it's possible to isolate those applications in
1867 their own address space using seccomp. Once seccomp is
1868 enabled via prctl(PR_SET_SECCOMP), it cannot be disabled
1869 and the task is only allowed to execute a few safe syscalls
1870 defined by each seccomp mode.
1872 config CC_STACKPROTECTOR
1873 bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
1875 This option turns on the -fstack-protector GCC feature. This
1876 feature puts, at the beginning of functions, a canary value on
1877 the stack just before the return address, and validates
1878 the value just before actually returning. Stack based buffer
1879 overflows (that need to overwrite this return address) now also
1880 overwrite the canary, which gets detected and the attack is then
1881 neutralized via a kernel panic.
1882 This feature requires gcc version 4.2 or above.
1889 bool "Xen guest support on ARM (EXPERIMENTAL)"
1890 depends on ARM && AEABI && OF
1891 depends on CPU_V7 && !CPU_V6
1892 depends on !GENERIC_ATOMIC64
1894 Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
1901 bool "Flattened Device Tree support"
1904 select OF_EARLY_FLATTREE
1906 Include support for flattened device tree machine descriptions.
1909 bool "Support for the traditional ATAGS boot data passing" if USE_OF
1912 This is the traditional way of passing data to the kernel at boot
1913 time. If you are solely relying on the flattened device tree (or
1914 the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
1915 to remove ATAGS support from your kernel binary. If unsure,
1918 config DEPRECATED_PARAM_STRUCT
1919 bool "Provide old way to pass kernel parameters"
1922 This was deprecated in 2001 and announced to live on for 5 years.
1923 Some old boot loaders still use this way.
1925 # Compressed boot loader in ROM. Yes, we really want to ask about
1926 # TEXT and BSS so we preserve their values in the config files.
1927 config ZBOOT_ROM_TEXT
1928 hex "Compressed ROM boot loader base address"
1931 The physical address at which the ROM-able zImage is to be
1932 placed in the target. Platforms which normally make use of
1933 ROM-able zImage formats normally set this to a suitable
1934 value in their defconfig file.
1936 If ZBOOT_ROM is not enabled, this has no effect.
1938 config ZBOOT_ROM_BSS
1939 hex "Compressed ROM boot loader BSS address"
1942 The base address of an area of read/write memory in the target
1943 for the ROM-able zImage which must be available while the
1944 decompressor is running. It must be large enough to hold the
1945 entire decompressed kernel plus an additional 128 KiB.
1946 Platforms which normally make use of ROM-able zImage formats
1947 normally set this to a suitable value in their defconfig file.
1949 If ZBOOT_ROM is not enabled, this has no effect.
1952 bool "Compressed boot loader in ROM/flash"
1953 depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS
1955 Say Y here if you intend to execute your compressed kernel image
1956 (zImage) directly from ROM or flash. If unsure, say N.
1959 prompt "Include SD/MMC loader in zImage (EXPERIMENTAL)"
1960 depends on ZBOOT_ROM && ARCH_SH7372
1961 default ZBOOT_ROM_NONE
1963 Include experimental SD/MMC loading code in the ROM-able zImage.
1964 With this enabled it is possible to write the ROM-able zImage
1965 kernel image to an MMC or SD card and boot the kernel straight
1966 from the reset vector. At reset the processor Mask ROM will load
1967 the first part of the ROM-able zImage which in turn loads the
1968 rest the kernel image to RAM.
1970 config ZBOOT_ROM_NONE
1971 bool "No SD/MMC loader in zImage (EXPERIMENTAL)"
1973 Do not load image from SD or MMC
1975 config ZBOOT_ROM_MMCIF
1976 bool "Include MMCIF loader in zImage (EXPERIMENTAL)"
1978 Load image from MMCIF hardware block.
1980 config ZBOOT_ROM_SH_MOBILE_SDHI
1981 bool "Include SuperH Mobile SDHI loader in zImage (EXPERIMENTAL)"
1983 Load image from SDHI hardware block
1987 config ARM_APPENDED_DTB
1988 bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
1989 depends on OF && !ZBOOT_ROM
1991 With this option, the boot code will look for a device tree binary
1992 (DTB) appended to zImage
1993 (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
1995 This is meant as a backward compatibility convenience for those
1996 systems with a bootloader that can't be upgraded to accommodate
1997 the documented boot protocol using a device tree.
1999 Beware that there is very little in terms of protection against
2000 this option being confused by leftover garbage in memory that might
2001 look like a DTB header after a reboot if no actual DTB is appended
2002 to zImage. Do not leave this option active in a production kernel
2003 if you don't intend to always append a DTB. Proper passing of the
2004 location into r2 of a bootloader provided DTB is always preferable
2007 config ARM_ATAG_DTB_COMPAT
2008 bool "Supplement the appended DTB with traditional ATAG information"
2009 depends on ARM_APPENDED_DTB
2011 Some old bootloaders can't be updated to a DTB capable one, yet
2012 they provide ATAGs with memory configuration, the ramdisk address,
2013 the kernel cmdline string, etc. Such information is dynamically
2014 provided by the bootloader and can't always be stored in a static
2015 DTB. To allow a device tree enabled kernel to be used with such
2016 bootloaders, this option allows zImage to extract the information
2017 from the ATAG list and store it at run time into the appended DTB.
2020 prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
2021 default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
2023 config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
2024 bool "Use bootloader kernel arguments if available"
2026 Uses the command-line options passed by the boot loader instead of
2027 the device tree bootargs property. If the boot loader doesn't provide
2028 any, the device tree bootargs property will be used.
2030 config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND
2031 bool "Extend with bootloader kernel arguments"
2033 The command-line arguments provided by the boot loader will be
2034 appended to the the device tree bootargs property.
2039 string "Default kernel command string"
2042 On some architectures (EBSA110 and CATS), there is currently no way
2043 for the boot loader to pass arguments to the kernel. For these
2044 architectures, you should supply some command-line options at build
2045 time by entering them here. As a minimum, you should specify the
2046 memory size and the root device (e.g., mem=64M root=/dev/nfs).
2049 prompt "Kernel command line type" if CMDLINE != ""
2050 default CMDLINE_FROM_BOOTLOADER
2053 config CMDLINE_FROM_BOOTLOADER
2054 bool "Use bootloader kernel arguments if available"
2056 Uses the command-line options passed by the boot loader. If
2057 the boot loader doesn't provide any, the default kernel command
2058 string provided in CMDLINE will be used.
2060 config CMDLINE_EXTEND
2061 bool "Extend bootloader kernel arguments"
2063 The command-line arguments provided by the boot loader will be
2064 appended to the default kernel command string.
2066 config CMDLINE_FORCE
2067 bool "Always use the default kernel command string"
2069 Always use the default kernel command string, even if the boot
2070 loader passes other arguments to the kernel.
2071 This is useful if you cannot or don't want to change the
2072 command-line options your boot loader passes to the kernel.
2076 bool "Kernel Execute-In-Place from ROM"
2077 depends on !ZBOOT_ROM && !ARM_LPAE && !ARCH_MULTIPLATFORM
2079 Execute-In-Place allows the kernel to run from non-volatile storage
2080 directly addressable by the CPU, such as NOR flash. This saves RAM
2081 space since the text section of the kernel is not loaded from flash
2082 to RAM. Read-write sections, such as the data section and stack,
2083 are still copied to RAM. The XIP kernel is not compressed since
2084 it has to run directly from flash, so it will take more space to
2085 store it. The flash address used to link the kernel object files,
2086 and for storing it, is configuration dependent. Therefore, if you
2087 say Y here, you must know the proper physical address where to
2088 store the kernel image depending on your own flash memory usage.
2090 Also note that the make target becomes "make xipImage" rather than
2091 "make zImage" or "make Image". The final kernel binary to put in
2092 ROM memory will be arch/arm/boot/xipImage.
2096 config XIP_PHYS_ADDR
2097 hex "XIP Kernel Physical Location"
2098 depends on XIP_KERNEL
2099 default "0x00080000"
2101 This is the physical address in your flash memory the kernel will
2102 be linked for and stored to. This address is dependent on your
2106 bool "Kexec system call (EXPERIMENTAL)"
2107 depends on (!SMP || HOTPLUG_CPU)
2109 kexec is a system call that implements the ability to shutdown your
2110 current kernel, and to start another kernel. It is like a reboot
2111 but it is independent of the system firmware. And like a reboot
2112 you can start any kernel with it, not just Linux.
2114 It is an ongoing process to be certain the hardware in a machine
2115 is properly shutdown, so do not be surprised if this code does not
2116 initially work for you. It may help to enable device hotplugging
2120 bool "Export atags in procfs"
2121 depends on ATAGS && KEXEC
2124 Should the atags used to boot the kernel be exported in an "atags"
2125 file in procfs. Useful with kexec.
2128 bool "Build kdump crash kernel (EXPERIMENTAL)"
2130 Generate crash dump after being started by kexec. This should
2131 be normally only set in special crash dump kernels which are
2132 loaded in the main kernel with kexec-tools into a specially
2133 reserved region and then later executed after a crash by
2134 kdump/kexec. The crash dump kernel must be compiled to a
2135 memory address not used by the main kernel
2137 For more details see Documentation/kdump/kdump.txt
2139 config AUTO_ZRELADDR
2140 bool "Auto calculation of the decompressed kernel image address"
2141 depends on !ZBOOT_ROM && !ARCH_U300
2143 ZRELADDR is the physical address where the decompressed kernel
2144 image will be placed. If AUTO_ZRELADDR is selected, the address
2145 will be determined at run-time by masking the current IP with
2146 0xf8000000. This assumes the zImage being placed in the first 128MB
2147 from start of memory.
2151 menu "CPU Power Management"
2155 source "drivers/cpufreq/Kconfig"
2158 tristate "CPUfreq driver for i.MX CPUs"
2159 depends on ARCH_MXC && CPU_FREQ
2160 select CPU_FREQ_TABLE
2162 This enables the CPUfreq driver for i.MX CPUs.
2164 config CPU_FREQ_SA1100
2167 config CPU_FREQ_SA1110
2170 config CPU_FREQ_INTEGRATOR
2171 tristate "CPUfreq driver for ARM Integrator CPUs"
2172 depends on ARCH_INTEGRATOR && CPU_FREQ
2175 This enables the CPUfreq driver for ARM Integrator CPUs.
2177 For details, take a look at <file:Documentation/cpu-freq>.
2183 depends on CPU_FREQ && ARCH_PXA && PXA25x
2185 select CPU_FREQ_DEFAULT_GOV_USERSPACE
2186 select CPU_FREQ_TABLE
2191 Internal configuration node for common cpufreq on Samsung SoC
2193 config CPU_FREQ_S3C24XX
2194 bool "CPUfreq driver for Samsung S3C24XX series CPUs (EXPERIMENTAL)"
2195 depends on ARCH_S3C24XX && CPU_FREQ
2198 This enables the CPUfreq driver for the Samsung S3C24XX family
2201 For details, take a look at <file:Documentation/cpu-freq>.
2205 config CPU_FREQ_S3C24XX_PLL
2206 bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)"
2207 depends on CPU_FREQ_S3C24XX
2209 Compile in support for changing the PLL frequency from the
2210 S3C24XX series CPUfreq driver. The PLL takes time to settle
2211 after a frequency change, so by default it is not enabled.
2213 This also means that the PLL tables for the selected CPU(s) will
2214 be built which may increase the size of the kernel image.
2216 config CPU_FREQ_S3C24XX_DEBUG
2217 bool "Debug CPUfreq Samsung driver core"
2218 depends on CPU_FREQ_S3C24XX
2220 Enable s3c_freq_dbg for the Samsung S3C CPUfreq core
2222 config CPU_FREQ_S3C24XX_IODEBUG
2223 bool "Debug CPUfreq Samsung driver IO timing"
2224 depends on CPU_FREQ_S3C24XX
2226 Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core
2228 config CPU_FREQ_S3C24XX_DEBUGFS
2229 bool "Export debugfs for CPUFreq"
2230 depends on CPU_FREQ_S3C24XX && DEBUG_FS
2232 Export status information via debugfs.
2236 source "drivers/cpuidle/Kconfig"
2240 menu "Floating point emulation"
2242 comment "At least one emulation must be selected"
2245 bool "NWFPE math emulation"
2246 depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL
2248 Say Y to include the NWFPE floating point emulator in the kernel.
2249 This is necessary to run most binaries. Linux does not currently
2250 support floating point hardware so you need to say Y here even if
2251 your machine has an FPA or floating point co-processor podule.
2253 You may say N here if you are going to load the Acorn FPEmulator
2254 early in the bootup.
2257 bool "Support extended precision"
2258 depends on FPE_NWFPE
2260 Say Y to include 80-bit support in the kernel floating-point
2261 emulator. Otherwise, only 32 and 64-bit support is compiled in.
2262 Note that gcc does not generate 80-bit operations by default,
2263 so in most cases this option only enlarges the size of the
2264 floating point emulator without any good reason.
2266 You almost surely want to say N here.
2269 bool "FastFPE math emulation (EXPERIMENTAL)"
2270 depends on (!AEABI || OABI_COMPAT) && !CPU_32v3
2272 Say Y here to include the FAST floating point emulator in the kernel.
2273 This is an experimental much faster emulator which now also has full
2274 precision for the mantissa. It does not support any exceptions.
2275 It is very simple, and approximately 3-6 times faster than NWFPE.
2277 It should be sufficient for most programs. It may be not suitable
2278 for scientific calculations, but you have to check this for yourself.
2279 If you do not feel you need a faster FP emulation you should better
2283 bool "VFP-format floating point maths"
2284 depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON
2286 Say Y to include VFP support code in the kernel. This is needed
2287 if your hardware includes a VFP unit.
2289 Please see <file:Documentation/arm/VFP/release-notes.txt> for
2290 release notes and additional status information.
2292 Say N if your target does not have VFP hardware.
2300 bool "Advanced SIMD (NEON) Extension support"
2301 depends on VFPv3 && CPU_V7
2303 Say Y to include support code for NEON, the ARMv7 Advanced SIMD
2308 menu "Userspace binary formats"
2310 source "fs/Kconfig.binfmt"
2313 tristate "RISC OS personality"
2316 Say Y here to include the kernel code necessary if you want to run
2317 Acorn RISC OS/Arthur binaries under Linux. This code is still very
2318 experimental; if this sounds frightening, say N and sleep in peace.
2319 You can also say M here to compile this support as a module (which
2320 will be called arthur).
2324 menu "Power management options"
2326 source "kernel/power/Kconfig"
2328 config ARCH_SUSPEND_POSSIBLE
2329 depends on !ARCH_S5PC100
2330 depends on CPU_ARM920T || CPU_ARM926T || CPU_SA1100 || \
2331 CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK
2334 config ARM_CPU_SUSPEND
2339 source "net/Kconfig"
2341 source "drivers/Kconfig"
2345 source "arch/arm/Kconfig.debug"
2347 source "security/Kconfig"
2349 source "crypto/Kconfig"
2351 source "lib/Kconfig"
2353 source "arch/arm/kvm/Kconfig"