2 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
10 #include "omap36xx.dtsi"
13 model = "TI OMAP3 BeagleBoard xM";
14 compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3";
23 device_type = "memory";
24 reg = <0x80000000 0x20000000>; /* 512 MB */
28 compatible = "gpio-leds";
31 label = "beagleboard::usr0";
32 gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
33 linux,default-trigger = "heartbeat";
37 label = "beagleboard::usr1";
38 gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
39 linux,default-trigger = "mmc0";
44 compatible = "pwm-leds";
47 label = "beagleboard::pmu_stat";
48 pwms = <&twl_pwmled 1 7812500>;
49 max-brightness = <127>;
54 compatible = "ti,omap-twl4030";
55 ti,model = "omap3beagle";
58 ti,codec = <&twl_audio>;
62 compatible = "gpio-keys";
66 gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
73 /* HS USB Port 2 Power */
74 hsusb2_power: hsusb2_power_reg {
75 compatible = "regulator-fixed";
76 regulator-name = "hsusb2_vbus";
77 regulator-min-microvolt = <3300000>;
78 regulator-max-microvolt = <3300000>;
79 gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
80 startup-delay-us = <70000>;
83 /* HS USB Host PHY on PORT 2 */
84 hsusb2_phy: hsusb2_phy {
85 compatible = "usb-nop-xceiv";
86 reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
87 vcc-supply = <&hsusb2_power>;
92 gpio1_pins: pinmux_gpio1_pins {
93 pinctrl-single,pins = <
94 0x0e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */
100 pinctrl-names = "default";
105 uart3_pins: pinmux_uart3_pins {
106 pinctrl-single,pins = <
107 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
108 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
112 hsusbb2_pins: pinmux_hsusbb2_pins {
113 pinctrl-single,pins = <
114 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
115 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
116 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
117 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
118 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
119 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
120 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
121 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
122 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
123 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
124 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
125 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
131 clock-frequency = <2600000>;
135 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
136 interrupt-parent = <&intc>;
139 compatible = "ti,twl4030-audio";
146 #include "twl4030.dtsi"
147 #include "twl4030_omap3.dtsi"
150 clock-frequency = <400000>;
154 clock-frequency = <100000>;
157 * Display monitor features are burnt in the EEPROM
161 compatible = "ti,eeprom";
167 vmmc-supply = <&vmmc1>;
168 vmmc_aux-supply = <&vsim>;
182 /* pullups: BIT(1) */
183 ti,pullups = <0x000002>;
186 * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
187 * BIT(15), BIT(16), BIT(17)
189 ti,pulldowns = <0x03a1c4>;
193 interface-type = <0>;
194 usb-phy = <&usb2_phy>;
196 phy-names = "usb2-phy";
202 pinctrl-names = "default";
203 pinctrl-0 = <&uart3_pins>;
207 pinctrl-names = "default";
208 pinctrl-0 = <&gpio1_pins>;
212 port2-mode = "ehci-phy";
216 phys = <0 &hsusb2_phy>;