2 * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
10 #include "omap34xx.dtsi"
13 model = "TI OMAP3 BeagleBoard";
14 compatible = "ti,omap3-beagle", "ti,omap3";
23 device_type = "memory";
24 reg = <0x80000000 0x10000000>; /* 256 MB */
28 compatible = "gpio-leds";
30 label = "beagleboard::pmu_stat";
31 gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
35 label = "beagleboard::usr0";
36 gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */
37 linux,default-trigger = "heartbeat";
41 label = "beagleboard::usr1";
42 gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */
43 linux,default-trigger = "mmc0";
47 /* HS USB Port 2 Power */
48 hsusb2_power: hsusb2_power_reg {
49 compatible = "regulator-fixed";
50 regulator-name = "hsusb2_vbus";
51 regulator-min-microvolt = <3300000>;
52 regulator-max-microvolt = <3300000>;
53 gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
54 startup-delay-us = <70000>;
57 /* HS USB Host PHY on PORT 2 */
58 hsusb2_phy: hsusb2_phy {
59 compatible = "usb-nop-xceiv";
60 reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
61 vcc-supply = <&hsusb2_power>;
65 compatible = "gpio-keys";
69 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
78 gpio1_pins: pinmux_gpio1_pins {
79 pinctrl-single,pins = <
80 0x14 (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot5.gpio_7 */
86 pinctrl-names = "default";
91 hsusbb2_pins: pinmux_hsusbb2_pins {
92 pinctrl-single,pins = <
93 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
94 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
95 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
96 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
97 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
98 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
99 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
100 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
101 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
102 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
103 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
104 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
108 uart3_pins: pinmux_uart3_pins {
109 pinctrl-single,pins = <
110 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
111 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
117 clock-frequency = <2600000>;
121 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
122 interrupt-parent = <&intc>;
126 #include "twl4030.dtsi"
127 #include "twl4030_omap3.dtsi"
130 vmmc-supply = <&vmmc1>;
131 vmmc_aux-supply = <&vsim>;
144 port2-mode = "ehci-phy";
148 phys = <0 &hsusb2_phy>;
153 /* pullups: BIT(1) */
154 ti,pullups = <0x000002>;
157 * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
158 * BIT(15), BIT(16), BIT(17)
160 ti,pulldowns = <0x03a1c4>;
164 pinctrl-names = "default";
165 pinctrl-0 = <&uart3_pins>;
169 pinctrl-names = "default";
170 pinctrl-0 = <&gpio1_pins>;
174 interface-type = <0>;
175 usb-phy = <&usb2_phy>;
177 phy-names = "usb2-phy";