2 * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
8 #include "elpida_ecb240abacn.dtsi"
11 model = "TI OMAP4 PandaBoard";
12 compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
15 device_type = "memory";
16 reg = <0x80000000 0x40000000>; /* 1 GB */
20 compatible = "gpio-leds";
21 pinctrl-names = "default";
27 label = "pandaboard::status1";
28 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
29 linux,default-trigger = "heartbeat";
33 label = "pandaboard::status2";
34 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
35 linux,default-trigger = "mmc0";
40 compatible = "ti,abe-twl6040";
41 ti,model = "PandaBoard";
43 ti,mclk-freq = <38400000>;
47 ti,twl6040 = <&twl6040>;
51 "Headset Stereophone", "HSOL",
52 "Headset Stereophone", "HSOR",
57 "HSMIC", "Headset Mic",
58 "Headset Mic", "Headset Mic Bias",
63 /* HS USB Port 1 Power */
64 hsusb1_power: hsusb1_power_reg {
65 compatible = "regulator-fixed";
66 regulator-name = "hsusb1_vbus";
67 regulator-min-microvolt = <3300000>;
68 regulator-max-microvolt = <3300000>;
69 gpio = <&gpio1 1 0>; /* gpio_1 */
70 startup-delay-us = <70000>;
73 * boot-on is required along with always-on as the
74 * regulator framework doesn't enable the regulator
75 * if boot-on is not there.
81 /* HS USB Host PHY on PORT 1 */
82 hsusb1_phy: hsusb1_phy {
83 compatible = "usb-nop-xceiv";
84 reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
85 vcc-supply = <&hsusb1_power>;
88 * put the right clock phandle here when available
89 * clocks = <&auxclk3>;
90 * clock-names = "main_clk";
92 clock-frequency = <19200000>;
95 /* regulator for wl12xx on sdio5 */
96 wl12xx_vmmc: wl12xx_vmmc {
97 pinctrl-names = "default";
98 pinctrl-0 = <&wl12xx_gpio>;
99 compatible = "regulator-fixed";
100 regulator-name = "vwl1271";
101 regulator-min-microvolt = <1800000>;
102 regulator-max-microvolt = <1800000>;
103 gpio = <&gpio2 11 0>;
104 startup-delay-us = <70000>;
110 pinctrl-names = "default";
120 twl6040_pins: pinmux_twl6040_pins {
121 pinctrl-single,pins = <
122 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
123 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
127 mcpdm_pins: pinmux_mcpdm_pins {
128 pinctrl-single,pins = <
129 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
130 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
131 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
132 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
133 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
137 mcbsp1_pins: pinmux_mcbsp1_pins {
138 pinctrl-single,pins = <
139 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
140 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
141 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
142 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
146 dss_hdmi_pins: pinmux_dss_hdmi_pins {
147 pinctrl-single,pins = <
148 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
149 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
150 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
154 tpd12s015_pins: pinmux_tpd12s015_pins {
155 pinctrl-single,pins = <
156 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
157 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
158 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
162 hsusbb1_pins: pinmux_hsusbb1_pins {
163 pinctrl-single,pins = <
164 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
165 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
166 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
167 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
168 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
169 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
170 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
171 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
172 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
173 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
174 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
175 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
179 i2c1_pins: pinmux_i2c1_pins {
180 pinctrl-single,pins = <
181 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
182 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
186 i2c2_pins: pinmux_i2c2_pins {
187 pinctrl-single,pins = <
188 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
189 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
193 i2c3_pins: pinmux_i2c3_pins {
194 pinctrl-single,pins = <
195 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
196 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
200 i2c4_pins: pinmux_i2c4_pins {
201 pinctrl-single,pins = <
202 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
203 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
209 led_wkgpio_pins: pinmux_leds_wkpins {
210 pinctrl-single,pins = <
211 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
212 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
217 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
218 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
220 wl12xx_gpio: pinmux_wl12xx_gpio {
221 pinctrl-single,pins = <
222 0x26 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */
223 0x2c (PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */
224 0x30 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
225 0x32 (PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */
229 /* wl12xx GPIO inputs and SDIO pins */
230 wl12xx_pins: pinmux_wl12xx_pins {
231 pinctrl-single,pins = <
232 0x38 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
233 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
234 0x108 (PIN_OUTPUT | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
235 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
236 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
237 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
238 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
239 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
245 pinctrl-names = "default";
246 pinctrl-0 = <&i2c1_pins>;
248 clock-frequency = <400000>;
253 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
254 interrupt-parent = <&gic>;
258 compatible = "ti,twl6040";
261 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
262 interrupt-parent = <&gic>;
263 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
265 vio-supply = <&v1v8>;
266 v2v1-supply = <&v2v1>;
271 #include "twl6030.dtsi"
272 #include "twl6030_omap4.dtsi"
275 pinctrl-names = "default";
276 pinctrl-0 = <&i2c2_pins>;
278 clock-frequency = <400000>;
282 pinctrl-names = "default";
283 pinctrl-0 = <&i2c3_pins>;
285 clock-frequency = <100000>;
288 * Display monitor features are burnt in their EEPROM as EDID data.
289 * The EEPROM is connected as I2C slave device.
292 compatible = "ti,eeprom";
298 pinctrl-names = "default";
299 pinctrl-0 = <&i2c4_pins>;
301 clock-frequency = <400000>;
305 vmmc-supply = <&vmmc>;
322 pinctrl-names = "default";
323 pinctrl-0 = <&wl12xx_pins>;
324 vmmc-supply = <&wl12xx_vmmc>;
332 device-handle = <&elpida_ECB240ABACN>;
337 device-handle = <&elpida_ECB240ABACN>;
352 &twl_usb_comparator {
353 usb-supply = <&vusb>;
357 interface-type = <1>;
363 port1-mode = "ehci-phy";
367 phys = <&hsusb1_phy>;