2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
9 #include <dt-bindings/interrupt-controller/irq.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
17 vmmcsd_fixed: fixedregulator-mmcsd {
18 compatible = "regulator-fixed";
19 regulator-name = "vmmcsd_fixed";
20 regulator-min-microvolt = <3000000>;
21 regulator-max-microvolt = <3000000>;
24 mmc3_pwrseq: sdhci0_pwrseq {
25 compatible = "mmc-pwrseq-simple";
26 clocks = <&clk32kgaudio>;
27 clock-names = "ext_clock";
30 vmmcsdio_fixed: fixedregulator-mmcsdio {
31 compatible = "regulator-fixed";
32 regulator-name = "vmmcsdio_fixed";
33 regulator-min-microvolt = <1800000>;
34 regulator-max-microvolt = <1800000>;
35 gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
37 startup-delay-us = <70000>;
38 pinctrl-names = "default";
39 pinctrl-0 = <&wlan_pins>;
42 /* HS USB Host PHY on PORT 2 */
43 hsusb2_phy: hsusb2_phy {
44 compatible = "usb-nop-xceiv";
45 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
46 clocks = <&auxclk1_ck>;
47 clock-names = "main_clk";
48 clock-frequency = <19200000>;
51 /* HS USB Host PHY on PORT 3 */
52 hsusb3_phy: hsusb3_phy {
53 compatible = "usb-nop-xceiv";
54 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
58 compatible = "gpio-leds";
60 label = "omap5:blue:usr1";
61 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
62 linux,default-trigger = "heartbeat";
63 default-state = "off";
67 tpd12s015: encoder@0 {
68 compatible = "ti,tpd12s015";
70 pinctrl-names = "default";
71 pinctrl-0 = <&tpd12s015_pins>;
73 /* gpios defined in the board specific dts */
82 tpd12s015_in: endpoint@0 {
83 remote-endpoint = <&hdmi_out>;
90 tpd12s015_out: endpoint@0 {
91 remote-endpoint = <&hdmi_connector_in>;
98 compatible = "hdmi-connector";
104 hdmi_connector_in: endpoint {
105 remote-endpoint = <&tpd12s015_out>;
111 compatible = "ti,abe-twl6040";
112 ti,model = "omap5-uevm";
114 ti,mclk-freq = <19200000>;
118 ti,twl6040 = <&twl6040>;
122 "Headset Stereophone", "HSOL",
123 "Headset Stereophone", "HSOR",
126 "HSMIC", "Headset Mic",
127 "Headset Mic", "Headset Mic Bias",
134 /* TI trees use GPIO instead of msecure, see also muxing */
137 gpios = <10 GPIO_ACTIVE_HIGH>;
139 line-name = "gpio8_234/msecure";
144 pinctrl-names = "default";
150 twl6040_pins: pinmux_twl6040_pins {
151 pinctrl-single,pins = <
152 OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
156 mcpdm_pins: pinmux_mcpdm_pins {
157 pinctrl-single,pins = <
158 OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
159 OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
160 OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
161 OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
162 OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
166 mcbsp1_pins: pinmux_mcbsp1_pins {
167 pinctrl-single,pins = <
168 OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
169 OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
170 OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
171 OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
175 mcbsp2_pins: pinmux_mcbsp2_pins {
176 pinctrl-single,pins = <
177 OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
178 OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
179 OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
180 OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
184 i2c1_pins: pinmux_i2c1_pins {
185 pinctrl-single,pins = <
186 OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
187 OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
191 mcspi2_pins: pinmux_mcspi2_pins {
192 pinctrl-single,pins = <
193 OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
194 OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
195 OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
196 OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
200 mcspi3_pins: pinmux_mcspi3_pins {
201 pinctrl-single,pins = <
202 OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
203 OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
204 OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
205 OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
209 mmc3_pins: pinmux_mmc3_pins {
210 pinctrl-single,pins = <
211 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
212 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
213 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
214 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
215 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
216 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
220 wlan_pins: pinmux_wlan_pins {
221 pinctrl-single,pins = <
222 OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
226 /* TI trees use GPIO mode; msecure mode does not work reliably? */
227 palmas_msecure_pins: palmas_msecure_pins {
228 pinctrl-single,pins = <
229 OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
233 usbhost_pins: pinmux_usbhost_pins {
234 pinctrl-single,pins = <
235 OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
236 OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
238 OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
239 OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
241 OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
242 OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
246 led_gpio_pins: pinmux_led_gpio_pins {
247 pinctrl-single,pins = <
248 OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
252 uart1_pins: pinmux_uart1_pins {
253 pinctrl-single,pins = <
254 OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
255 OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
256 OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
257 OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
261 uart3_pins: pinmux_uart3_pins {
262 pinctrl-single,pins = <
263 OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
264 OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
268 uart5_pins: pinmux_uart5_pins {
269 pinctrl-single,pins = <
270 OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
271 OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
272 OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
273 OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
277 dss_hdmi_pins: pinmux_dss_hdmi_pins {
278 pinctrl-single,pins = <
279 OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
280 OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
281 OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
285 tpd12s015_pins: pinmux_tpd12s015_pins {
286 pinctrl-single,pins = <
287 OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
293 pinctrl-names = "default";
298 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
299 pinctrl-single,pins = <
300 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */
304 usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
305 pinctrl-single,pins = <
306 OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
310 wlcore_irq_pin: pinmux_wlcore_irq_pin {
311 pinctrl-single,pins = <
312 OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
318 vmmc-supply = <&ldo9_reg>;
323 vmmc-supply = <&vmmcsd_fixed>;
329 vmmc-supply = <&vmmcsdio_fixed>;
330 mmc-pwrseq = <&mmc3_pwrseq>;
334 pinctrl-names = "default";
335 pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
336 interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
337 &omap5_pmx_core 0x168>;
339 #address-cells = <1>;
342 compatible = "ti,wl1271";
344 interrupt-parent = <&gpio1>;
345 interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
346 ref-clock-frequency = <26000000>;
359 pinctrl-names = "default";
360 pinctrl-0 = <&i2c1_pins>;
362 clock-frequency = <400000>;
365 compatible = "ti,palmas";
366 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
368 interrupt-controller;
369 #interrupt-cells = <2>;
370 ti,system-power-controller;
371 pinctrl-names = "default";
372 pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
374 extcon_usb3: palmas_usb {
375 compatible = "ti,palmas-usb-vid";
376 ti,enable-vbus-detection;
377 ti,enable-id-detection;
381 clk32kgaudio: palmas_clk32k@1 {
382 compatible = "ti,palmas-clk32kgaudio";
387 compatible = "ti,palmas-rtc";
388 interrupt-parent = <&palmas>;
389 interrupts = <8 IRQ_TYPE_NONE>;
390 ti,backup-battery-chargeable;
391 ti,backup-battery-charge-high-current;
395 compatible = "ti,palmas-pmic";
396 interrupt-parent = <&palmas>;
397 interrupts = <14 IRQ_TYPE_NONE>;
398 interrupt-name = "short-irq";
403 smps123_reg: smps123 {
405 regulator-name = "smps123";
406 regulator-min-microvolt = < 600000>;
407 regulator-max-microvolt = <1500000>;
414 regulator-name = "smps45";
415 regulator-min-microvolt = < 600000>;
416 regulator-max-microvolt = <1310000>;
422 /* VDD_DDR3 - over VDD_SMPS6 */
423 regulator-name = "smps6";
424 regulator-min-microvolt = <1200000>;
425 regulator-max-microvolt = <1200000>;
431 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
432 regulator-name = "smps7";
433 regulator-min-microvolt = <1800000>;
434 regulator-max-microvolt = <1800000>;
441 regulator-name = "smps8";
442 regulator-min-microvolt = < 600000>;
443 regulator-max-microvolt = <1310000>;
449 /* VDDA_2v1_AUD over VDD_2v1 */
450 regulator-name = "smps9";
451 regulator-min-microvolt = <2100000>;
452 regulator-max-microvolt = <2100000>;
453 ti,smps-range = <0x80>;
456 smps10_out2_reg: smps10_out2 {
458 regulator-name = "smps10_out2";
459 regulator-min-microvolt = <5000000>;
460 regulator-max-microvolt = <5000000>;
465 smps10_out1_reg: smps10_out1 {
467 regulator-name = "smps10_out1";
468 regulator-min-microvolt = <5000000>;
469 regulator-max-microvolt = <5000000>;
473 /* VDDAPHY_CAM: vdda_csiport */
474 regulator-name = "ldo1";
475 regulator-min-microvolt = <1500000>;
476 regulator-max-microvolt = <1800000>;
480 /* VCC_2V8_DISP: Does not go anywhere */
481 regulator-name = "ldo2";
482 regulator-min-microvolt = <2800000>;
483 regulator-max-microvolt = <2800000>;
489 /* VDDAPHY_MDM: vdda_lli */
490 regulator-name = "ldo3";
491 regulator-min-microvolt = <1500000>;
492 regulator-max-microvolt = <1500000>;
494 /* Only if Modem is used */
499 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
500 regulator-name = "ldo4";
501 regulator-min-microvolt = <1500000>;
502 regulator-max-microvolt = <1800000>;
506 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
507 regulator-name = "ldo5";
508 regulator-min-microvolt = <1800000>;
509 regulator-max-microvolt = <1800000>;
515 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
516 regulator-name = "ldo6";
517 regulator-min-microvolt = <1200000>;
518 regulator-max-microvolt = <1200000>;
525 regulator-name = "ldo7";
526 regulator-min-microvolt = <2000000>;
527 regulator-max-microvolt = <2000000>;
528 /* Only for efuse reprograming! */
533 /* VDD_3v0: Does not go anywhere */
534 regulator-name = "ldo8";
535 regulator-min-microvolt = <3000000>;
536 regulator-max-microvolt = <3000000>;
543 /* VCC_DV_SDIO: vdds_sdcard */
544 regulator-name = "ldo9";
545 regulator-min-microvolt = <1800000>;
546 regulator-max-microvolt = <3000000>;
551 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
552 regulator-name = "ldoln";
553 regulator-min-microvolt = <1800000>;
554 regulator-max-microvolt = <1800000>;
560 /* VDDA_3V_USB: VDDA_USBHS33 */
561 regulator-name = "ldousb";
562 regulator-min-microvolt = <3250000>;
563 regulator-max-microvolt = <3250000>;
569 /* REGEN3 controls LDO9 supply to card */
570 regulator-name = "regen3";
577 palmas_power_button: palmas_power_button {
578 compatible = "ti,palmas-pwrbutton";
579 interrupt-parent = <&palmas>;
580 interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
586 compatible = "ti,twl6040";
589 pinctrl-names = "default";
590 pinctrl-0 = <&twl6040_pins>;
592 interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
593 ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */
595 vio-supply = <&smps7_reg>;
596 v2v1-supply = <&smps9_reg>;
599 clocks = <&clk32kgaudio>;
600 clock-names = "clk32k";
605 pinctrl-names = "default";
606 pinctrl-0 = <&mcpdm_pins>;
611 pinctrl-names = "default";
612 pinctrl-0 = <&mcbsp1_pins>;
617 pinctrl-names = "default";
618 pinctrl-0 = <&mcbsp2_pins>;
623 port2-mode = "ehci-hsic";
624 port3-mode = "ehci-hsic";
628 phys = <0 &hsusb2_phy &hsusb3_phy>;
632 extcon = <&extcon_usb3>;
633 vbus-supply = <&smps10_out1_reg>;
641 pinctrl-names = "default";
642 pinctrl-0 = <&mcspi2_pins>;
646 pinctrl-names = "default";
647 pinctrl-0 = <&mcspi3_pins>;
651 pinctrl-names = "default";
652 pinctrl-0 = <&uart1_pins>;
656 pinctrl-names = "default";
657 pinctrl-0 = <&uart3_pins>;
658 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
659 <&omap5_pmx_core 0x19c>;
663 pinctrl-names = "default";
664 pinctrl-0 = <&uart5_pins>;
668 cpu0-supply = <&smps123_reg>;
678 /* vdda-supply populated in board specific dts file */
680 pinctrl-names = "default";
681 pinctrl-0 = <&dss_hdmi_pins>;
685 remote-endpoint = <&tpd12s015_in>;