2 * linux/arch/arm/mach-at91/board-usb-a926x.c
4 * Copyright (C) 2005 SAN People
5 * Copyright (C) 2007 Atmel Corporation.
6 * Copyright (C) 2007 Calao-systems
7 * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License as published by
11 * the Free Software Foundation; either version 2 of the License, or
12 * (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
24 #include <linux/types.h>
25 #include <linux/init.h>
27 #include <linux/module.h>
28 #include <linux/platform_device.h>
29 #include <linux/spi/spi.h>
30 #include <linux/gpio_keys.h>
31 #include <linux/gpio.h>
32 #include <linux/input.h>
33 #include <linux/spi/mmc_spi.h>
35 #include <asm/setup.h>
36 #include <asm/mach-types.h>
39 #include <asm/mach/arch.h>
40 #include <asm/mach/map.h>
41 #include <asm/mach/irq.h>
43 #include <mach/hardware.h>
44 #include <mach/board.h>
45 #include <mach/at91sam9_smc.h>
46 #include <mach/at91_shdwc.h>
52 static void __init ek_init_early(void)
54 /* Initialize processor: 12.00 MHz crystal */
55 at91_initialize(12000000);
57 /* DBGU on ttyS0. (Rx & Tx only) */
58 at91_register_uart(0, 0, 0);
60 /* set serial console to ttyS0 (ie, DBGU) */
61 at91_set_serial_console(0);
67 static struct at91_usbh_data __initdata ek_usbh_data = {
69 .vbus_pin = {-EINVAL, -EINVAL},
70 .overcurrent_pin= {-EINVAL, -EINVAL},
76 static struct at91_udc_data __initdata ek_udc_data = {
77 .vbus_pin = AT91_PIN_PB11,
78 .pullup_pin = -EINVAL, /* pull-up driven by UDC */
81 static void __init ek_add_device_udc(void)
83 if (machine_is_usb_a9260() || machine_is_usb_a9g20())
84 ek_udc_data.vbus_pin = AT91_PIN_PC5;
86 at91_add_device_udc(&ek_udc_data);
89 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
90 #define MMC_SPI_CARD_DETECT_INT AT91_PIN_PC4
91 static int at91_mmc_spi_init(struct device *dev,
92 irqreturn_t (*detect_int)(int, void *), void *data)
94 /* Configure Interrupt pin as input, no pull-up */
95 at91_set_gpio_input(MMC_SPI_CARD_DETECT_INT, 0);
96 return request_irq(gpio_to_irq(MMC_SPI_CARD_DETECT_INT), detect_int,
97 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
98 "mmc-spi-detect", data);
101 static void at91_mmc_spi_exit(struct device *dev, void *data)
103 free_irq(gpio_to_irq(MMC_SPI_CARD_DETECT_INT), data);
106 static struct mmc_spi_platform_data at91_mmc_spi_pdata = {
107 .init = at91_mmc_spi_init,
108 .exit = at91_mmc_spi_exit,
109 .detect_delay = 100, /* msecs */
116 static struct spi_board_info usb_a9263_spi_devices[] = {
117 #if !defined(CONFIG_MMC_AT91)
118 { /* DataFlash chip */
119 .modalias = "mtd_dataflash",
121 .max_speed_hz = 15 * 1000 * 1000,
127 static struct spi_board_info usb_a9g20_spi_devices[] = {
128 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
130 .modalias = "mmc_spi",
131 .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
134 .platform_data = &at91_mmc_spi_pdata,
140 static void __init ek_add_device_spi(void)
142 if (machine_is_usb_a9263())
143 at91_add_device_spi(usb_a9263_spi_devices, ARRAY_SIZE(usb_a9263_spi_devices));
144 else if (machine_is_usb_a9g20())
145 at91_add_device_spi(usb_a9g20_spi_devices, ARRAY_SIZE(usb_a9g20_spi_devices));
149 * MACB Ethernet device
151 static struct macb_platform_data __initdata ek_macb_data = {
152 .phy_irq_pin = AT91_PIN_PE31,
156 static void __init ek_add_device_eth(void)
158 if (machine_is_usb_a9260() || machine_is_usb_a9g20())
159 ek_macb_data.phy_irq_pin = AT91_PIN_PA31;
161 at91_add_device_eth(&ek_macb_data);
167 static struct mtd_partition __initdata ek_nand_partition[] = {
173 .name = "bareboxenv",
174 .offset = MTDPART_OFS_NXTBLK,
177 .name = "bareboxenv2",
178 .offset = MTDPART_OFS_NXTBLK,
182 .offset = MTDPART_OFS_NXTBLK,
186 .offset = MTDPART_OFS_NXTBLK,
190 .offset = MTDPART_OFS_NXTBLK,
191 .size = MTDPART_SIZ_FULL,
195 static struct atmel_nand_data __initdata ek_nand_data = {
199 .rdy_pin = AT91_PIN_PA22,
200 .enable_pin = AT91_PIN_PD15,
201 .ecc_mode = NAND_ECC_SOFT,
203 .parts = ek_nand_partition,
204 .num_parts = ARRAY_SIZE(ek_nand_partition),
207 static struct sam9_smc_config __initdata usb_a9260_nand_smc_config = {
210 .ncs_write_setup = 0,
215 .ncs_write_pulse = 3,
221 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
225 static struct sam9_smc_config __initdata usb_a9g20_nand_smc_config = {
228 .ncs_write_setup = 0,
233 .ncs_write_pulse = 4,
239 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
243 static void __init ek_add_device_nand(void)
245 if (machine_is_usb_a9260() || machine_is_usb_a9g20()) {
246 ek_nand_data.rdy_pin = AT91_PIN_PC13;
247 ek_nand_data.enable_pin = AT91_PIN_PC14;
250 /* configure chip-select 3 (NAND) */
251 if (machine_is_usb_a9g20())
252 sam9_smc_configure(0, 3, &usb_a9g20_nand_smc_config);
254 sam9_smc_configure(0, 3, &usb_a9260_nand_smc_config);
256 at91_add_device_nand(&ek_nand_data);
263 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
264 static struct gpio_keys_button ek_buttons[] = {
265 { /* USER PUSH BUTTON */
267 .gpio = AT91_PIN_PB10,
274 static struct gpio_keys_platform_data ek_button_data = {
275 .buttons = ek_buttons,
276 .nbuttons = ARRAY_SIZE(ek_buttons),
279 static struct platform_device ek_button_device = {
284 .platform_data = &ek_button_data,
288 static void __init ek_add_device_buttons(void)
290 at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */
291 at91_set_deglitch(AT91_PIN_PB10, 1);
293 platform_device_register(&ek_button_device);
296 static void __init ek_add_device_buttons(void) {}
302 static struct gpio_led ek_leds[] = {
303 { /* user_led (green) */
305 .gpio = AT91_PIN_PB21,
307 .default_trigger = "heartbeat",
311 static struct i2c_board_info __initdata ek_i2c_devices[] = {
313 I2C_BOARD_INFO("rv3029c2", 0x56),
317 static void __init ek_add_device_leds(void)
319 if (machine_is_usb_a9260() || machine_is_usb_a9g20())
320 ek_leds[0].active_low = 0;
322 at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
325 static void __init ek_board_init(void)
328 at91_add_device_serial();
330 at91_add_device_usbh(&ek_usbh_data);
338 ek_add_device_nand();
340 ek_add_device_buttons();
342 ek_add_device_leds();
344 if (machine_is_usb_a9g20()) {
346 at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
349 at91_add_device_i2c(NULL, 0);
350 /* shutdown controller, wakeup button (5 msec low) */
351 at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
352 | AT91_SHDW_WKMODE0_LOW
353 | AT91_SHDW_RTTWKEN);
357 MACHINE_START(USB_A9263, "CALAO USB_A9263")
358 /* Maintainer: calao-systems */
359 .timer = &at91sam926x_timer,
360 .map_io = at91_map_io,
361 .init_early = ek_init_early,
362 .init_irq = at91_init_irq_default,
363 .init_machine = ek_board_init,
366 MACHINE_START(USB_A9260, "CALAO USB_A9260")
367 /* Maintainer: calao-systems */
368 .timer = &at91sam926x_timer,
369 .map_io = at91_map_io,
370 .init_early = ek_init_early,
371 .init_irq = at91_init_irq_default,
372 .init_machine = ek_board_init,
375 MACHINE_START(USB_A9G20, "CALAO USB_A92G0")
376 /* Maintainer: Jean-Christophe PLAGNIOL-VILLARD */
377 .timer = &at91sam926x_timer,
378 .map_io = at91_map_io,
379 .init_early = ek_init_early,
380 .init_irq = at91_init_irq_default,
381 .init_machine = ek_board_init,