2 * linux/arch/arm/mach-omap1/board-h2.c
4 * Board specific inits for OMAP-1610 H2
6 * Copyright (C) 2001 RidgeRun, Inc.
7 * Author: Greg Lonnon <glonnon@ridgerun.com>
9 * Copyright (C) 2002 MontaVista Software, Inc.
11 * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
12 * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
14 * H2 specific changes and cleanup
15 * Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
17 * This program is free software; you can redistribute it and/or modify
18 * it under the terms of the GNU General Public License version 2 as
19 * published by the Free Software Foundation.
21 #include <linux/gpio.h>
22 #include <linux/kernel.h>
23 #include <linux/platform_device.h>
24 #include <linux/delay.h>
25 #include <linux/i2c.h>
26 #include <linux/mtd/mtd.h>
27 #include <linux/mtd/nand.h>
28 #include <linux/mtd/partitions.h>
29 #include <linux/mtd/physmap.h>
30 #include <linux/input.h>
31 #include <linux/i2c/tps65010.h>
32 #include <linux/smc91x.h>
33 #include <linux/omapfb.h>
35 #include <asm/mach-types.h>
36 #include <asm/mach/arch.h>
37 #include <asm/mach/map.h>
42 #include <plat/irda.h>
44 #include <plat/keypad.h>
45 #include <plat/flash.h>
47 #include <mach/hardware.h>
52 /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
53 #define OMAP1610_ETHR_START 0x04000300
55 static const unsigned int h2_keymap[] = {
93 static struct mtd_partition h2_nor_partitions[] = {
94 /* bootloader (U-Boot, etc) in first sector */
99 .mask_flags = MTD_WRITEABLE, /* force read-only */
101 /* bootloader params in the next sector */
104 .offset = MTDPART_OFS_APPEND,
111 .offset = MTDPART_OFS_APPEND,
117 .name = "filesystem",
118 .offset = MTDPART_OFS_APPEND,
119 .size = MTDPART_SIZ_FULL,
124 static struct physmap_flash_data h2_nor_data = {
126 .set_vpp = omap1_set_vpp,
127 .parts = h2_nor_partitions,
128 .nr_parts = ARRAY_SIZE(h2_nor_partitions),
131 static struct resource h2_nor_resource = {
132 /* This is on CS3, wherever it's mapped */
133 .flags = IORESOURCE_MEM,
136 static struct platform_device h2_nor_device = {
137 .name = "physmap-flash",
140 .platform_data = &h2_nor_data,
143 .resource = &h2_nor_resource,
146 static struct mtd_partition h2_nand_partitions[] = {
148 /* REVISIT: enable these partitions if you make NAND BOOT
149 * work on your H2 (rev C or newer); published versions of
150 * x-load only support P2 and H3.
156 .mask_flags = MTD_WRITEABLE, /* force read-only */
159 .name = "bootloader",
160 .offset = MTDPART_OFS_APPEND,
162 .mask_flags = MTD_WRITEABLE, /* force read-only */
166 .offset = MTDPART_OFS_APPEND,
171 .offset = MTDPART_OFS_APPEND,
176 .name = "filesystem",
177 .size = MTDPART_SIZ_FULL,
178 .offset = MTDPART_OFS_APPEND,
182 static void h2_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
184 struct nand_chip *this = mtd->priv;
187 if (cmd == NAND_CMD_NONE)
190 mask = (ctrl & NAND_CLE) ? 0x02 : 0;
193 writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
196 #define H2_NAND_RB_GPIO_PIN 62
198 static int h2_nand_dev_ready(struct mtd_info *mtd)
200 return gpio_get_value(H2_NAND_RB_GPIO_PIN);
203 static const char *h2_part_probes[] = { "cmdlinepart", NULL };
205 static struct platform_nand_data h2_nand_platdata = {
209 .nr_partitions = ARRAY_SIZE(h2_nand_partitions),
210 .partitions = h2_nand_partitions,
211 .options = NAND_SAMSUNG_LP_OPTIONS,
212 .part_probe_types = h2_part_probes,
215 .cmd_ctrl = h2_nand_cmd_ctl,
216 .dev_ready = h2_nand_dev_ready,
221 static struct resource h2_nand_resource = {
222 .flags = IORESOURCE_MEM,
225 static struct platform_device h2_nand_device = {
229 .platform_data = &h2_nand_platdata,
232 .resource = &h2_nand_resource,
235 static struct smc91x_platdata h2_smc91x_info = {
236 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
237 .leda = RPC_LED_100_10,
238 .ledb = RPC_LED_TX_RX,
241 static struct resource h2_smc91x_resources[] = {
243 .start = OMAP1610_ETHR_START, /* Physical */
244 .end = OMAP1610_ETHR_START + 0xf,
245 .flags = IORESOURCE_MEM,
248 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
252 static struct platform_device h2_smc91x_device = {
256 .platform_data = &h2_smc91x_info,
258 .num_resources = ARRAY_SIZE(h2_smc91x_resources),
259 .resource = h2_smc91x_resources,
262 static struct resource h2_kp_resources[] = {
264 .start = INT_KEYBOARD,
266 .flags = IORESOURCE_IRQ,
270 static const struct matrix_keymap_data h2_keymap_data = {
272 .keymap_size = ARRAY_SIZE(h2_keymap),
275 static struct omap_kp_platform_data h2_kp_data = {
278 .keymap_data = &h2_keymap_data,
284 static struct platform_device h2_kp_device = {
285 .name = "omap-keypad",
288 .platform_data = &h2_kp_data,
290 .num_resources = ARRAY_SIZE(h2_kp_resources),
291 .resource = h2_kp_resources,
294 #define H2_IRDA_FIRSEL_GPIO_PIN 17
296 static struct omap_irda_config h2_irda_data = {
297 .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
298 .rx_channel = OMAP_DMA_UART3_RX,
299 .tx_channel = OMAP_DMA_UART3_TX,
300 .dest_start = UART3_THR,
301 .src_start = UART3_RHR,
306 static struct resource h2_irda_resources[] = {
310 .flags = IORESOURCE_IRQ,
314 static u64 irda_dmamask = 0xffffffff;
316 static struct platform_device h2_irda_device = {
320 .platform_data = &h2_irda_data,
321 .dma_mask = &irda_dmamask,
323 .num_resources = ARRAY_SIZE(h2_irda_resources),
324 .resource = h2_irda_resources,
327 static struct platform_device *h2_devices[] __initdata = {
335 static void __init h2_init_smc91x(void)
337 if (gpio_request(0, "SMC91x irq") < 0) {
338 printk("Error requesting gpio 0 for smc91x irq\n");
343 static int tps_setup(struct i2c_client *client, void *context)
345 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
346 TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
351 static struct tps65010_board tps_board = {
352 .base = H2_TPS_GPIO_BASE,
357 static struct i2c_board_info __initdata h2_i2c_board_info[] = {
359 I2C_BOARD_INFO("tps65010", 0x48),
360 .platform_data = &tps_board,
362 I2C_BOARD_INFO("isp1301_omap", 0x2d),
366 static struct omap_usb_config h2_usb_config __initdata = {
367 /* usb1 has a Mini-AB port and external isp1301 transceiver */
370 #ifdef CONFIG_USB_GADGET_OMAP
371 .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
372 /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
373 #elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
374 /* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
375 .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
381 static struct omap_lcd_config h2_lcd_config __initdata = {
382 .ctrl_name = "internal",
385 static void __init h2_init(void)
389 /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
390 * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
391 * notice whether a NAND chip is enabled at probe time.
393 * FIXME revC boards (and H3) support NAND-boot, with a dip switch to
394 * put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
395 * detecting that in code here, to avoid probing every possible flash
398 h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
399 h2_nor_resource.end += SZ_32M - 1;
401 h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
402 h2_nand_resource.end += SZ_4K - 1;
403 if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
405 gpio_direction_input(H2_NAND_RB_GPIO_PIN);
407 omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
408 omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
410 /* MMC: card detect and WP */
411 /* omap_cfg_reg(U19_ARMIO1); */ /* CD */
412 omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
414 /* Mux pins for keypad */
415 omap_cfg_reg(F18_1610_KBC0);
416 omap_cfg_reg(D20_1610_KBC1);
417 omap_cfg_reg(D19_1610_KBC2);
418 omap_cfg_reg(E18_1610_KBC3);
419 omap_cfg_reg(C21_1610_KBC4);
420 omap_cfg_reg(G18_1610_KBR0);
421 omap_cfg_reg(F19_1610_KBR1);
422 omap_cfg_reg(H14_1610_KBR2);
423 omap_cfg_reg(E20_1610_KBR3);
424 omap_cfg_reg(E19_1610_KBR4);
425 omap_cfg_reg(N19_1610_KBR5);
427 h2_smc91x_resources[1].start = gpio_to_irq(0);
428 h2_smc91x_resources[1].end = gpio_to_irq(0);
429 platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
431 h2_i2c_board_info[0].irq = gpio_to_irq(58);
432 h2_i2c_board_info[1].irq = gpio_to_irq(2);
433 omap_register_i2c_bus(1, 100, h2_i2c_board_info,
434 ARRAY_SIZE(h2_i2c_board_info));
435 omap1_usb_init(&h2_usb_config);
438 omapfb_set_lcd_config(&h2_lcd_config);
441 MACHINE_START(OMAP_H2, "TI-H2")
442 /* Maintainer: Imre Deak <imre.deak@nokia.com> */
443 .atag_offset = 0x100,
444 .map_io = omap16xx_map_io,
445 .init_early = omap1_init_early,
446 .reserve = omap_reserve,
447 .init_irq = omap1_init_irq,
448 .init_machine = h2_init,
449 .timer = &omap1_timer,
450 .restart = omap1_restart,