2 * linux/arch/arm/mach-omap1/board-h2.c
4 * Board specific inits for OMAP-1610 H2
6 * Copyright (C) 2001 RidgeRun, Inc.
7 * Author: Greg Lonnon <glonnon@ridgerun.com>
9 * Copyright (C) 2002 MontaVista Software, Inc.
11 * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
12 * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
14 * H2 specific changes and cleanup
15 * Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
17 * This program is free software; you can redistribute it and/or modify
18 * it under the terms of the GNU General Public License version 2 as
19 * published by the Free Software Foundation.
21 #include <linux/gpio.h>
22 #include <linux/kernel.h>
23 #include <linux/platform_device.h>
24 #include <linux/delay.h>
25 #include <linux/i2c.h>
26 #include <linux/mtd/mtd.h>
27 #include <linux/mtd/nand.h>
28 #include <linux/mtd/partitions.h>
29 #include <linux/mtd/physmap.h>
30 #include <linux/input.h>
31 #include <linux/i2c/tps65010.h>
32 #include <linux/smc91x.h>
33 #include <linux/omapfb.h>
34 #include <linux/leds.h>
36 #include <asm/mach-types.h>
37 #include <asm/mach/arch.h>
38 #include <asm/mach/map.h>
43 #include <plat/irda.h>
44 #include <plat/keypad.h>
45 #include <plat/flash.h>
47 #include <mach/hardware.h>
53 /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
54 #define OMAP1610_ETHR_START 0x04000300
56 static const unsigned int h2_keymap[] = {
94 static struct mtd_partition h2_nor_partitions[] = {
95 /* bootloader (U-Boot, etc) in first sector */
100 .mask_flags = MTD_WRITEABLE, /* force read-only */
102 /* bootloader params in the next sector */
105 .offset = MTDPART_OFS_APPEND,
112 .offset = MTDPART_OFS_APPEND,
118 .name = "filesystem",
119 .offset = MTDPART_OFS_APPEND,
120 .size = MTDPART_SIZ_FULL,
125 static struct physmap_flash_data h2_nor_data = {
127 .set_vpp = omap1_set_vpp,
128 .parts = h2_nor_partitions,
129 .nr_parts = ARRAY_SIZE(h2_nor_partitions),
132 static struct resource h2_nor_resource = {
133 /* This is on CS3, wherever it's mapped */
134 .flags = IORESOURCE_MEM,
137 static struct platform_device h2_nor_device = {
138 .name = "physmap-flash",
141 .platform_data = &h2_nor_data,
144 .resource = &h2_nor_resource,
147 static struct mtd_partition h2_nand_partitions[] = {
149 /* REVISIT: enable these partitions if you make NAND BOOT
150 * work on your H2 (rev C or newer); published versions of
151 * x-load only support P2 and H3.
157 .mask_flags = MTD_WRITEABLE, /* force read-only */
160 .name = "bootloader",
161 .offset = MTDPART_OFS_APPEND,
163 .mask_flags = MTD_WRITEABLE, /* force read-only */
167 .offset = MTDPART_OFS_APPEND,
172 .offset = MTDPART_OFS_APPEND,
177 .name = "filesystem",
178 .size = MTDPART_SIZ_FULL,
179 .offset = MTDPART_OFS_APPEND,
183 #define H2_NAND_RB_GPIO_PIN 62
185 static int h2_nand_dev_ready(struct mtd_info *mtd)
187 return gpio_get_value(H2_NAND_RB_GPIO_PIN);
190 static struct platform_nand_data h2_nand_platdata = {
194 .nr_partitions = ARRAY_SIZE(h2_nand_partitions),
195 .partitions = h2_nand_partitions,
196 .options = NAND_SAMSUNG_LP_OPTIONS,
199 .cmd_ctrl = omap1_nand_cmd_ctl,
200 .dev_ready = h2_nand_dev_ready,
204 static struct resource h2_nand_resource = {
205 .flags = IORESOURCE_MEM,
208 static struct platform_device h2_nand_device = {
212 .platform_data = &h2_nand_platdata,
215 .resource = &h2_nand_resource,
218 static struct smc91x_platdata h2_smc91x_info = {
219 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
220 .leda = RPC_LED_100_10,
221 .ledb = RPC_LED_TX_RX,
224 static struct resource h2_smc91x_resources[] = {
226 .start = OMAP1610_ETHR_START, /* Physical */
227 .end = OMAP1610_ETHR_START + 0xf,
228 .flags = IORESOURCE_MEM,
231 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
235 static struct platform_device h2_smc91x_device = {
239 .platform_data = &h2_smc91x_info,
241 .num_resources = ARRAY_SIZE(h2_smc91x_resources),
242 .resource = h2_smc91x_resources,
245 static struct resource h2_kp_resources[] = {
247 .start = INT_KEYBOARD,
249 .flags = IORESOURCE_IRQ,
253 static const struct matrix_keymap_data h2_keymap_data = {
255 .keymap_size = ARRAY_SIZE(h2_keymap),
258 static struct omap_kp_platform_data h2_kp_data = {
261 .keymap_data = &h2_keymap_data,
267 static struct platform_device h2_kp_device = {
268 .name = "omap-keypad",
271 .platform_data = &h2_kp_data,
273 .num_resources = ARRAY_SIZE(h2_kp_resources),
274 .resource = h2_kp_resources,
277 #define H2_IRDA_FIRSEL_GPIO_PIN 17
279 static struct omap_irda_config h2_irda_data = {
280 .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
281 .rx_channel = OMAP_DMA_UART3_RX,
282 .tx_channel = OMAP_DMA_UART3_TX,
283 .dest_start = UART3_THR,
284 .src_start = UART3_RHR,
289 static struct resource h2_irda_resources[] = {
293 .flags = IORESOURCE_IRQ,
297 static u64 irda_dmamask = 0xffffffff;
299 static struct platform_device h2_irda_device = {
303 .platform_data = &h2_irda_data,
304 .dma_mask = &irda_dmamask,
306 .num_resources = ARRAY_SIZE(h2_irda_resources),
307 .resource = h2_irda_resources,
310 static struct gpio_led h2_gpio_led_pins[] = {
313 .default_trigger = "heartbeat",
318 .default_trigger = "cpu0",
319 .gpio = OMAP_MPUIO(4),
323 static struct gpio_led_platform_data h2_gpio_led_data = {
324 .leds = h2_gpio_led_pins,
325 .num_leds = ARRAY_SIZE(h2_gpio_led_pins),
328 static struct platform_device h2_gpio_leds = {
332 .platform_data = &h2_gpio_led_data,
336 static struct platform_device *h2_devices[] __initdata = {
345 static void __init h2_init_smc91x(void)
347 if (gpio_request(0, "SMC91x irq") < 0) {
348 printk("Error requesting gpio 0 for smc91x irq\n");
353 static int tps_setup(struct i2c_client *client, void *context)
355 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
356 TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
361 static struct tps65010_board tps_board = {
362 .base = H2_TPS_GPIO_BASE,
367 static struct i2c_board_info __initdata h2_i2c_board_info[] = {
369 I2C_BOARD_INFO("tps65010", 0x48),
370 .platform_data = &tps_board,
372 I2C_BOARD_INFO("isp1301_omap", 0x2d),
376 static struct omap_usb_config h2_usb_config __initdata = {
377 /* usb1 has a Mini-AB port and external isp1301 transceiver */
380 #ifdef CONFIG_USB_GADGET_OMAP
381 .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
382 /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
383 #elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
384 /* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
385 .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
391 static struct omap_lcd_config h2_lcd_config __initdata = {
392 .ctrl_name = "internal",
395 static void __init h2_init(void)
399 /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
400 * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
401 * notice whether a NAND chip is enabled at probe time.
403 * FIXME revC boards (and H3) support NAND-boot, with a dip switch to
404 * put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
405 * detecting that in code here, to avoid probing every possible flash
408 h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
409 h2_nor_resource.end += SZ_32M - 1;
411 h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
412 h2_nand_resource.end += SZ_4K - 1;
413 if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
415 gpio_direction_input(H2_NAND_RB_GPIO_PIN);
417 omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
418 omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
420 /* MMC: card detect and WP */
421 /* omap_cfg_reg(U19_ARMIO1); */ /* CD */
422 omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
424 /* Mux pins for keypad */
425 omap_cfg_reg(F18_1610_KBC0);
426 omap_cfg_reg(D20_1610_KBC1);
427 omap_cfg_reg(D19_1610_KBC2);
428 omap_cfg_reg(E18_1610_KBC3);
429 omap_cfg_reg(C21_1610_KBC4);
430 omap_cfg_reg(G18_1610_KBR0);
431 omap_cfg_reg(F19_1610_KBR1);
432 omap_cfg_reg(H14_1610_KBR2);
433 omap_cfg_reg(E20_1610_KBR3);
434 omap_cfg_reg(E19_1610_KBR4);
435 omap_cfg_reg(N19_1610_KBR5);
437 /* GPIO based LEDs */
438 omap_cfg_reg(P18_1610_GPIO3);
439 omap_cfg_reg(MPUIO4);
441 h2_smc91x_resources[1].start = gpio_to_irq(0);
442 h2_smc91x_resources[1].end = gpio_to_irq(0);
443 platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
445 h2_i2c_board_info[0].irq = gpio_to_irq(58);
446 h2_i2c_board_info[1].irq = gpio_to_irq(2);
447 omap_register_i2c_bus(1, 100, h2_i2c_board_info,
448 ARRAY_SIZE(h2_i2c_board_info));
449 omap1_usb_init(&h2_usb_config);
452 omapfb_set_lcd_config(&h2_lcd_config);
455 MACHINE_START(OMAP_H2, "TI-H2")
456 /* Maintainer: Imre Deak <imre.deak@nokia.com> */
457 .atag_offset = 0x100,
458 .map_io = omap16xx_map_io,
459 .init_early = omap1_init_early,
460 .reserve = omap_reserve,
461 .init_irq = omap1_init_irq,
462 .init_machine = h2_init,
463 .init_late = omap1_init_late,
464 .timer = &omap1_timer,
465 .restart = omap1_restart,