2 * linux/arch/arm/mach-omap1/board-perseus2.c
4 * Modified from board-generic.c
6 * Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
7 * Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
14 #include <linux/kernel.h>
15 #include <linux/init.h>
16 #include <linux/platform_device.h>
17 #include <linux/delay.h>
18 #include <linux/mtd/mtd.h>
19 #include <linux/mtd/nand.h>
20 #include <linux/mtd/partitions.h>
21 #include <linux/mtd/physmap.h>
22 #include <linux/input.h>
23 #include <linux/smc91x.h>
25 #include <mach/hardware.h>
26 #include <asm/mach-types.h>
27 #include <asm/mach/arch.h>
28 #include <asm/mach/map.h>
31 #include <mach/gpio.h>
33 #include <plat/fpga.h>
34 #include <plat/flash.h>
35 #include <plat/keypad.h>
36 #include <plat/common.h>
37 #include <plat/board.h>
39 static const unsigned int p2_keymap[] = {
48 KEY(3, 1, KEY_VOLUMEDOWN),
49 KEY(4, 1, KEY_VOLUMEUP),
50 KEY(5, 1, KEY_RECORD),
61 KEY(5, 3, KEY_KPSLASH),
66 KEY(4, 4, KEY_KPASTERISK),
70 static struct smc91x_platdata smc91x_info = {
71 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
72 .leda = RPC_LED_100_10,
73 .ledb = RPC_LED_TX_RX,
76 static struct resource smc91x_resources[] = {
78 .start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
79 .end = H2P2_DBG_FPGA_ETHR_START + 0xf,
80 .flags = IORESOURCE_MEM,
83 .start = INT_7XX_MPU_EXT_NIRQ,
85 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
89 static struct mtd_partition nor_partitions[] = {
90 /* bootloader (U-Boot, etc) in first sector */
95 .mask_flags = MTD_WRITEABLE, /* force read-only */
97 /* bootloader params in the next sector */
100 .offset = MTDPART_OFS_APPEND,
107 .offset = MTDPART_OFS_APPEND,
111 /* rest of flash is a file system */
114 .offset = MTDPART_OFS_APPEND,
115 .size = MTDPART_SIZ_FULL,
120 static struct physmap_flash_data nor_data = {
122 .set_vpp = omap1_set_vpp,
123 .parts = nor_partitions,
124 .nr_parts = ARRAY_SIZE(nor_partitions),
127 static struct resource nor_resource = {
128 .start = OMAP_CS0_PHYS,
129 .end = OMAP_CS0_PHYS + SZ_32M - 1,
130 .flags = IORESOURCE_MEM,
133 static struct platform_device nor_device = {
134 .name = "physmap-flash",
137 .platform_data = &nor_data,
140 .resource = &nor_resource,
143 static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
145 struct nand_chip *this = mtd->priv;
148 if (cmd == NAND_CMD_NONE)
151 mask = (ctrl & NAND_CLE) ? 0x02 : 0;
154 writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
157 #define P2_NAND_RB_GPIO_PIN 62
159 static int nand_dev_ready(struct mtd_info *mtd)
161 return gpio_get_value(P2_NAND_RB_GPIO_PIN);
164 static const char *part_probes[] = { "cmdlinepart", NULL };
166 static struct platform_nand_data nand_data = {
170 .options = NAND_SAMSUNG_LP_OPTIONS,
171 .part_probe_types = part_probes,
174 .cmd_ctrl = nand_cmd_ctl,
175 .dev_ready = nand_dev_ready,
179 static struct resource nand_resource = {
180 .start = OMAP_CS3_PHYS,
181 .end = OMAP_CS3_PHYS + SZ_4K - 1,
182 .flags = IORESOURCE_MEM,
185 static struct platform_device nand_device = {
189 .platform_data = &nand_data,
192 .resource = &nand_resource,
195 static struct platform_device smc91x_device = {
199 .platform_data = &smc91x_info,
201 .num_resources = ARRAY_SIZE(smc91x_resources),
202 .resource = smc91x_resources,
205 static struct resource kp_resources[] = {
207 .start = INT_7XX_MPUIO_KEYPAD,
208 .end = INT_7XX_MPUIO_KEYPAD,
209 .flags = IORESOURCE_IRQ,
213 static const struct matrix_keymap_data p2_keymap_data = {
215 .keymap_size = ARRAY_SIZE(p2_keymap),
218 static struct omap_kp_platform_data kp_data = {
221 .keymap_data = &p2_keymap_data,
226 static struct platform_device kp_device = {
227 .name = "omap-keypad",
230 .platform_data = &kp_data,
232 .num_resources = ARRAY_SIZE(kp_resources),
233 .resource = kp_resources,
236 static struct platform_device lcd_device = {
241 static struct platform_device *devices[] __initdata = {
249 static struct omap_lcd_config perseus2_lcd_config __initdata = {
250 .ctrl_name = "internal",
253 static struct omap_board_config_kernel perseus2_config[] __initdata = {
254 { OMAP_TAG_LCD, &perseus2_lcd_config },
257 static void __init perseus2_init_smc91x(void)
259 fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
261 fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
262 H2P2_DBG_FPGA_LAN_RESET);
266 static void __init omap_perseus2_init(void)
268 /* Early, board-dependent init */
271 * Hold GSM Reset until needed
273 omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
276 * UARTs -> done automagically by 8250 driver
280 * CSx timings, GPIO Mux ... setup
283 /* Flash: CS0 timings setup */
284 omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
285 omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
288 * Ethernet support through the debug board
291 omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
292 omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
295 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
296 * It is used as the Ethernet controller interrupt
298 omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
301 perseus2_init_smc91x();
303 if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
305 gpio_direction_input(P2_NAND_RB_GPIO_PIN);
307 omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
308 omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
310 /* Mux pins for keypad */
311 omap_cfg_reg(E2_7XX_KBR0);
312 omap_cfg_reg(J7_7XX_KBR1);
313 omap_cfg_reg(E1_7XX_KBR2);
314 omap_cfg_reg(F3_7XX_KBR3);
315 omap_cfg_reg(D2_7XX_KBR4);
316 omap_cfg_reg(C2_7XX_KBC0);
317 omap_cfg_reg(D3_7XX_KBC1);
318 omap_cfg_reg(E4_7XX_KBC2);
319 omap_cfg_reg(F4_7XX_KBC3);
320 omap_cfg_reg(E3_7XX_KBC4);
322 platform_add_devices(devices, ARRAY_SIZE(devices));
324 omap_board_config = perseus2_config;
325 omap_board_config_size = ARRAY_SIZE(perseus2_config);
327 omap_register_i2c_bus(1, 100, NULL, 0);
330 /* Only FPGA needs to be mapped here. All others are done with ioremap */
331 static struct map_desc omap_perseus2_io_desc[] __initdata = {
333 .virtual = H2P2_DBG_FPGA_BASE,
334 .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
335 .length = H2P2_DBG_FPGA_SIZE,
340 static void __init omap_perseus2_map_io(void)
343 iotable_init(omap_perseus2_io_desc,
344 ARRAY_SIZE(omap_perseus2_io_desc));
347 MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
348 /* Maintainer: Kevin Hilman <kjh@hilman.org> */
349 .boot_params = 0x10000100,
350 .map_io = omap_perseus2_map_io,
351 .init_early = omap1_init_early,
352 .reserve = omap_reserve,
353 .init_irq = omap1_init_irq,
354 .init_machine = omap_perseus2_init,
355 .timer = &omap1_timer,