arch/arm/mach-omap2/serial.c

   1 /*
   2  * arch/arm/mach-omap2/serial.c
   3  *
   4  * OMAP2 serial support.
   5  *
   6  * Copyright (C) 2005-2008 Nokia Corporation
   7  * Author: Paul Mundt <paul.mundt@nokia.com>
   8  *
   9  * Major rework for PM support by Kevin Hilman
  10  *
  11  * Based off of arch/arm/mach-omap/omap1/serial.c
  12  *
  13  * Copyright (C) 2009 Texas Instruments
  14  * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com
  15  *
  16  * This file is subject to the terms and conditions of the GNU General Public
  17  * License. See the file "COPYING" in the main directory of this archive
  18  * for more details.
  19  */
  20 #include <linux/kernel.h>
  21 #include <linux/init.h>
  22 #include <linux/serial_reg.h>
  23 #include <linux/clk.h>
  24 #include <linux/io.h>
  25 #include <linux/delay.h>
  26 #include <linux/platform_device.h>
  27 #include <linux/slab.h>
  28 #include <linux/serial_8250.h>
  29 #include <linux/pm_runtime.h>
  30
  31 #ifdef CONFIG_SERIAL_OMAP
  32 #include <plat/omap-serial.h>
  33 #endif
  34
  35 #include <plat/common.h>
  36 #include <plat/board.h>
  37 #include <plat/clock.h>
  38 #include <plat/control.h>
  39 #include <plat/dma.h>
  40 #include <plat/omap_hwmod.h>
  41 #include <plat/omap_device.h>
  42
  43 #include "prm.h"
  44 #include "pm.h"
  45 #include "cm.h"
  46 #include "prm-regbits-34xx.h"
  47
  48 #define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV     0x52
  49 #define UART_OMAP_WER           0x17    /* Wake-up enable register */
  50
  51 #define UART_ERRATA_FIFO_FULL_ABORT     (0x1 << 0)
  52 #define UART_ERRATA_i202_MDR1_ACCESS    (0x1 << 1)
  53
  54 /*
  55  * NOTE: By default the serial timeout is disabled as it causes lost characters
  56  * over the serial ports. This means that the UART clocks will stay on until
  57  * disabled via sysfs. This also causes that any deeper omap sleep states are
  58  * blocked.
  59  */
  60 #define DEFAULT_TIMEOUT 0
  61
  62 #define MAX_UART_HWMOD_NAME_LEN         16
  63
  64 struct omap_uart_state {
  65         int num;
  66         int can_sleep;
  67         struct timer_list timer;
  68         u32 timeout;
  69
  70         void __iomem *wk_st;
  71         void __iomem *wk_en;
  72         u32 wk_mask;
  73         u32 padconf;
  74         u32 dma_enabled;
  75
  76         struct clk *ick;
  77         struct clk *fck;
  78         int clocked;
  79
  80         int irq;
  81         int regshift;
  82         int irqflags;
  83         void __iomem *membase;
  84         resource_size_t mapbase;
  85
  86         struct list_head node;
  87         struct omap_hwmod *oh;
  88         struct platform_device *pdev;
  89
  90         u32 errata;
  91 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
  92         int context_valid;
  93
  94         /* Registers to be saved/restored for OFF-mode */
  95         u16 dll;
  96         u16 dlh;
  97         u16 ier;
  98         u16 sysc;
  99         u16 scr;
 100         u16 wer;
 101         u16 mcr;
 102 #endif
 103 };
 104
 105 static LIST_HEAD(uart_list);
 106 static u8 num_uarts;
 107
 108 /*
 109  * Since these idle/enable hooks are used in the idle path itself
 110  * which has interrupts disabled, use the non-locking versions of
 111  * the hwmod enable/disable functions.
 112  */
 113 static int uart_idle_hwmod(struct omap_device *od)
 114 {
 115         _omap_hwmod_idle(od->hwmods[0]);
 116
 117         return 0;
 118 }
 119
 120 static int uart_enable_hwmod(struct omap_device *od)
 121 {
 122         _omap_hwmod_enable(od->hwmods[0]);
 123
 124         return 0;
 125 }
 126
 127 static struct omap_device_pm_latency omap_uart_latency[] = {
 128         {
 129                 .deactivate_func = uart_idle_hwmod,
 130                 .activate_func   = uart_enable_hwmod,
 131                 .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
 132         },
 133 };
 134
 135 static inline unsigned int __serial_read_reg(struct uart_port *up,
 136                                              int offset)
 137 {
 138         offset <<= up->regshift;
 139         return (unsigned int)__raw_readb(up->membase + offset);
 140 }
 141
 142 static inline unsigned int serial_read_reg(struct omap_uart_state *uart,
 143                                            int offset)
 144 {
 145         offset <<= uart->regshift;
 146         return (unsigned int)__raw_readb(uart->membase + offset);
 147 }
 148
 149 static inline void __serial_write_reg(struct uart_port *up, int offset,
 150                 int value)
 151 {
 152         offset <<= up->regshift;
 153         __raw_writeb(value, up->membase + offset);
 154 }
 155
 156 static inline void serial_write_reg(struct omap_uart_state *uart, int offset,
 157                                     int value)
 158 {
 159         offset <<= uart->regshift;
 160         __raw_writeb(value, uart->membase + offset);
 161 }
 162
 163 /*
 164  * Internal UARTs need to be initialized for the 8250 autoconfig to work
 165  * properly. Note that the TX watermark initialization may not be needed
 166  * once the 8250.c watermark handling code is merged.
 167  */
 168
 169 static inline void __init omap_uart_reset(struct omap_uart_state *uart)
 170 {
 171         serial_write_reg(uart, UART_OMAP_MDR1, 0x07);
 172         serial_write_reg(uart, UART_OMAP_SCR, 0x08);
 173         serial_write_reg(uart, UART_OMAP_MDR1, 0x00);
 174 }
 175
 176 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
 177
 178 /*
 179  * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
 180  * The access to uart register after MDR1 Access
 181  * causes UART to corrupt data.
 182  *
 183  * Need a delay =
 184  * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
 185  * give 10 times as much
 186  */
 187 static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
 188                 u8 fcr_val)
 189 {
 190         u8 timeout = 255;
 191
 192         serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val);
 193         udelay(2);
 194         serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
 195                         UART_FCR_CLEAR_RCVR);
 196         /*
 197          * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
 198          * TX_FIFO_E bit is 1.
 199          */
 200         while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) &
 201                                 (UART_LSR_THRE | UART_LSR_DR))) {
 202                 timeout--;
 203                 if (!timeout) {
 204                         /* Should *never* happen. we warn and carry on */
 205                         dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n",
 206                         serial_read_reg(uart, UART_LSR));
 207                         break;
 208                 }
 209                 udelay(1);
 210         }
 211 }
 212
 213 static void omap_uart_save_context(struct omap_uart_state *uart)
 214 {
 215         u16 lcr = 0;
 216
 217         if (!enable_off_mode)
 218                 return;
 219
 220         lcr = serial_read_reg(uart, UART_LCR);
 221         serial_write_reg(uart, UART_LCR, 0xBF);
 222         uart->dll = serial_read_reg(uart, UART_DLL);
 223         uart->dlh = serial_read_reg(uart, UART_DLM);
 224         serial_write_reg(uart, UART_LCR, lcr);
 225         uart->ier = serial_read_reg(uart, UART_IER);
 226         uart->sysc = serial_read_reg(uart, UART_OMAP_SYSC);
 227         uart->scr = serial_read_reg(uart, UART_OMAP_SCR);
 228         uart->wer = serial_read_reg(uart, UART_OMAP_WER);
 229         serial_write_reg(uart, UART_LCR, 0x80);
 230         uart->mcr = serial_read_reg(uart, UART_MCR);
 231         serial_write_reg(uart, UART_LCR, lcr);
 232
 233         uart->context_valid = 1;
 234 }
 235
 236 static void omap_uart_restore_context(struct omap_uart_state *uart)
 237 {
 238         u16 efr = 0;
 239
 240         if (!enable_off_mode)
 241                 return;
 242
 243         if (!uart->context_valid)
 244                 return;
 245
 246         uart->context_valid = 0;
 247
 248         if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
 249                 omap_uart_mdr1_errataset(uart, 0x07, 0xA0);
 250         else
 251                 serial_write_reg(uart, UART_OMAP_MDR1, 0x7);
 252         serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */
 253         efr = serial_read_reg(uart, UART_EFR);
 254         serial_write_reg(uart, UART_EFR, UART_EFR_ECB);
 255         serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
 256         serial_write_reg(uart, UART_IER, 0x0);
 257         serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */
 258         serial_write_reg(uart, UART_DLL, uart->dll);
 259         serial_write_reg(uart, UART_DLM, uart->dlh);
 260         serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */
 261         serial_write_reg(uart, UART_IER, uart->ier);
 262         serial_write_reg(uart, UART_LCR, 0x80);
 263         serial_write_reg(uart, UART_MCR, uart->mcr);
 264         serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */
 265         serial_write_reg(uart, UART_EFR, efr);
 266         serial_write_reg(uart, UART_LCR, UART_LCR_WLEN8);
 267         serial_write_reg(uart, UART_OMAP_SCR, uart->scr);
 268         serial_write_reg(uart, UART_OMAP_WER, uart->wer);
 269         serial_write_reg(uart, UART_OMAP_SYSC, uart->sysc);
 270         if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
 271                 omap_uart_mdr1_errataset(uart, 0x00, 0xA1);
 272         else
 273                 /* UART 16x mode */
 274                 serial_write_reg(uart, UART_OMAP_MDR1, 0x00);
 275 }
 276 #else
 277 static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
 278 static inline void omap_uart_restore_context(struct omap_uart_state *uart) {}
 279 #endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */
 280
 281 static inline void omap_uart_enable_clocks(struct omap_uart_state *uart)
 282 {
 283         if (uart->clocked)
 284                 return;
 285
 286         omap_device_enable(uart->pdev);
 287         uart->clocked = 1;
 288         omap_uart_restore_context(uart);
 289 }
 290
 291 #ifdef CONFIG_PM
 292
 293 static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
 294 {
 295         if (!uart->clocked)
 296                 return;
 297
 298         omap_uart_save_context(uart);
 299         uart->clocked = 0;
 300         omap_device_idle(uart->pdev);
 301 }
 302
 303 static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
 304 {
 305         /* Set wake-enable bit */
 306         if (uart->wk_en && uart->wk_mask) {
 307                 u32 v = __raw_readl(uart->wk_en);
 308                 v |= uart->wk_mask;
 309                 __raw_writel(v, uart->wk_en);
 310         }
 311
 312         /* Ensure IOPAD wake-enables are set */
 313         if (cpu_is_omap34xx() && uart->padconf) {
 314                 u16 v = omap_ctrl_readw(uart->padconf);
 315                 v |= OMAP3_PADCONF_WAKEUPENABLE0;
 316                 omap_ctrl_writew(v, uart->padconf);
 317         }
 318 }
 319
 320 static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
 321 {
 322         /* Clear wake-enable bit */
 323         if (uart->wk_en && uart->wk_mask) {
 324                 u32 v = __raw_readl(uart->wk_en);
 325                 v &= ~uart->wk_mask;
 326                 __raw_writel(v, uart->wk_en);
 327         }
 328
 329         /* Ensure IOPAD wake-enables are cleared */
 330         if (cpu_is_omap34xx() && uart->padconf) {
 331                 u16 v = omap_ctrl_readw(uart->padconf);
 332                 v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
 333                 omap_ctrl_writew(v, uart->padconf);
 334         }
 335 }
 336
 337 static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
 338                                                int enable)
 339 {
 340         u8 idlemode;
 341
 342         if (enable) {
 343                 /**
 344                  * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests
 345                  * in Smartidle Mode When Configured for DMA Operations.
 346                  */
 347                 if (uart->dma_enabled)
 348                         idlemode = HWMOD_IDLEMODE_FORCE;
 349                 else
 350                         idlemode = HWMOD_IDLEMODE_SMART;
 351         } else {
 352                 idlemode = HWMOD_IDLEMODE_NO;
 353         }
 354
 355         omap_hwmod_set_slave_idlemode(uart->oh, idlemode);
 356 }
 357
 358 static void omap_uart_block_sleep(struct omap_uart_state *uart)
 359 {
 360         omap_uart_enable_clocks(uart);
 361
 362         omap_uart_smart_idle_enable(uart, 0);
 363         uart->can_sleep = 0;
 364         if (uart->timeout)
 365                 mod_timer(&uart->timer, jiffies + uart->timeout);
 366         else
 367                 del_timer(&uart->timer);
 368 }
 369
 370 static void omap_uart_allow_sleep(struct omap_uart_state *uart)
 371 {
 372         if (device_may_wakeup(&uart->pdev->dev))
 373                 omap_uart_enable_wakeup(uart);
 374         else
 375                 omap_uart_disable_wakeup(uart);
 376
 377         if (!uart->clocked)
 378                 return;
 379
 380         omap_uart_smart_idle_enable(uart, 1);
 381         uart->can_sleep = 1;
 382         del_timer(&uart->timer);
 383 }
 384
 385 static void omap_uart_idle_timer(unsigned long data)
 386 {
 387         struct omap_uart_state *uart = (struct omap_uart_state *)data;
 388
 389         omap_uart_allow_sleep(uart);
 390 }
 391
 392 void omap_uart_prepare_idle(int num)
 393 {
 394         struct omap_uart_state *uart;
 395
 396         list_for_each_entry(uart, &uart_list, node) {
 397                 if (num == uart->num && uart->can_sleep) {
 398                         omap_uart_disable_clocks(uart);
 399                         return;
 400                 }
 401         }
 402 }
 403
 404 void omap_uart_resume_idle(int num)
 405 {
 406         struct omap_uart_state *uart;
 407
 408         list_for_each_entry(uart, &uart_list, node) {
 409                 if (num == uart->num) {
 410                         omap_uart_enable_clocks(uart);
 411
 412                         /* Check for IO pad wakeup */
 413                         if (cpu_is_omap34xx() && uart->padconf) {
 414                                 u16 p = omap_ctrl_readw(uart->padconf);
 415
 416                                 if (p & OMAP3_PADCONF_WAKEUPEVENT0)
 417                                         omap_uart_block_sleep(uart);
 418                         }
 419
 420                         /* Check for normal UART wakeup */
 421                         if (__raw_readl(uart->wk_st) & uart->wk_mask)
 422                                 omap_uart_block_sleep(uart);
 423                         return;
 424                 }
 425         }
 426 }
 427
 428 void omap_uart_prepare_suspend(void)
 429 {
 430         struct omap_uart_state *uart;
 431
 432         list_for_each_entry(uart, &uart_list, node) {
 433                 omap_uart_allow_sleep(uart);
 434         }
 435 }
 436
 437 int omap_uart_can_sleep(void)
 438 {
 439         struct omap_uart_state *uart;
 440         int can_sleep = 1;
 441
 442         list_for_each_entry(uart, &uart_list, node) {
 443                 if (!uart->clocked)
 444                         continue;
 445
 446                 if (!uart->can_sleep) {
 447                         can_sleep = 0;
 448                         continue;
 449                 }
 450
 451                 /* This UART can now safely sleep. */
 452                 omap_uart_allow_sleep(uart);
 453         }
 454
 455         return can_sleep;
 456 }
 457
 458 /**
 459  * omap_uart_interrupt()
 460  *
 461  * This handler is used only to detect that *any* UART interrupt has
 462  * occurred.  It does _nothing_ to handle the interrupt.  Rather,
 463  * any UART interrupt will trigger the inactivity timer so the
 464  * UART will not idle or sleep for its timeout period.
 465  *
 466  **/
 467 /* static int first_interrupt; */
 468 static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
 469 {
 470         struct omap_uart_state *uart = dev_id;
 471
 472         omap_uart_block_sleep(uart);
 473
 474         return IRQ_NONE;
 475 }
 476
 477 static void omap_uart_idle_init(struct omap_uart_state *uart)
 478 {
 479         int ret;
 480
 481         uart->can_sleep = 0;
 482         uart->timeout = DEFAULT_TIMEOUT;
 483         setup_timer(&uart->timer, omap_uart_idle_timer,
 484                     (unsigned long) uart);
 485         if (uart->timeout)
 486                 mod_timer(&uart->timer, jiffies + uart->timeout);
 487         omap_uart_smart_idle_enable(uart, 0);
 488
 489         if (cpu_is_omap34xx()) {
 490                 u32 mod = (uart->num > 1) ? OMAP3430_PER_MOD : CORE_MOD;
 491                 u32 wk_mask = 0;
 492                 u32 padconf = 0;
 493
 494                 uart->wk_en = OMAP34XX_PRM_REGADDR(mod, PM_WKEN1);
 495                 uart->wk_st = OMAP34XX_PRM_REGADDR(mod, PM_WKST1);
 496                 switch (uart->num) {
 497                 case 0:
 498                         wk_mask = OMAP3430_ST_UART1_MASK;
 499                         padconf = 0x182;
 500                         break;
 501                 case 1:
 502                         wk_mask = OMAP3430_ST_UART2_MASK;
 503                         padconf = 0x17a;
 504                         break;
 505                 case 2:
 506                         wk_mask = OMAP3430_ST_UART3_MASK;
 507                         padconf = 0x19e;
 508                         break;
 509                 case 3:
 510                         wk_mask = OMAP3630_ST_UART4_MASK;
 511                         padconf = 0x0d2;
 512                         break;
 513                 }
 514                 uart->wk_mask = wk_mask;
 515                 uart->padconf = padconf;
 516         } else if (cpu_is_omap24xx()) {
 517                 u32 wk_mask = 0;
 518
 519                 if (cpu_is_omap2430()) {
 520                         uart->wk_en = OMAP2430_PRM_REGADDR(CORE_MOD, PM_WKEN1);
 521                         uart->wk_st = OMAP2430_PRM_REGADDR(CORE_MOD, PM_WKST1);
 522                 } else if (cpu_is_omap2420()) {
 523                         uart->wk_en = OMAP2420_PRM_REGADDR(CORE_MOD, PM_WKEN1);
 524                         uart->wk_st = OMAP2420_PRM_REGADDR(CORE_MOD, PM_WKST1);
 525                 }
 526                 switch (uart->num) {
 527                 case 0:
 528                         wk_mask = OMAP24XX_ST_UART1_MASK;
 529                         break;
 530                 case 1:
 531                         wk_mask = OMAP24XX_ST_UART2_MASK;
 532                         break;
 533                 case 2:
 534                         wk_mask = OMAP24XX_ST_UART3_MASK;
 535                         break;
 536                 }
 537                 uart->wk_mask = wk_mask;
 538         } else {
 539                 uart->wk_en = NULL;
 540                 uart->wk_st = NULL;
 541                 uart->wk_mask = 0;
 542                 uart->padconf = 0;
 543         }
 544
 545         uart->irqflags |= IRQF_SHARED;
 546         ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt,
 547                                    IRQF_SHARED, "serial idle", (void *)uart);
 548         WARN_ON(ret);
 549 }
 550
 551 void omap_uart_enable_irqs(int enable)
 552 {
 553         int ret;
 554         struct omap_uart_state *uart;
 555
 556         list_for_each_entry(uart, &uart_list, node) {
 557                 if (enable) {
 558                         pm_runtime_put_sync(&uart->pdev->dev);
 559                         ret = request_threaded_irq(uart->irq, NULL,
 560                                                    omap_uart_interrupt,
 561                                                    IRQF_SHARED,
 562                                                    "serial idle",
 563                                                    (void *)uart);
 564                 } else {
 565                         pm_runtime_get_noresume(&uart->pdev->dev);
 566                         free_irq(uart->irq, (void *)uart);
 567                 }
 568         }
 569 }
 570
 571 static ssize_t sleep_timeout_show(struct device *dev,
 572                                   struct device_attribute *attr,
 573                                   char *buf)
 574 {
 575         struct platform_device *pdev = to_platform_device(dev);
 576         struct omap_device *odev = to_omap_device(pdev);
 577         struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
 578
 579         return sprintf(buf, "%u\n", uart->timeout / HZ);
 580 }
 581
 582 static ssize_t sleep_timeout_store(struct device *dev,
 583                                    struct device_attribute *attr,
 584                                    const char *buf, size_t n)
 585 {
 586         struct platform_device *pdev = to_platform_device(dev);
 587         struct omap_device *odev = to_omap_device(pdev);
 588         struct omap_uart_state *uart = odev->hwmods[0]->dev_attr;
 589         unsigned int value;
 590
 591         if (sscanf(buf, "%u", &value) != 1) {
 592                 dev_err(dev, "sleep_timeout_store: Invalid value\n");
 593                 return -EINVAL;
 594         }
 595
 596         uart->timeout = value * HZ;
 597         if (uart->timeout)
 598                 mod_timer(&uart->timer, jiffies + uart->timeout);
 599         else
 600                 /* A zero value means disable timeout feature */
 601                 omap_uart_block_sleep(uart);
 602
 603         return n;
 604 }
 605
 606 static DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show,
 607                 sleep_timeout_store);
 608 #define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
 609 #else
 610 static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
 611 static void omap_uart_block_sleep(struct omap_uart_state *uart) {}
 612 #define DEV_CREATE_FILE(dev, attr)
 613 #endif /* CONFIG_PM */
 614
 615 #ifndef CONFIG_SERIAL_OMAP
 616 /*
 617  * Override the default 8250 read handler: mem_serial_in()
 618  * Empty RX fifo read causes an abort on omap3630 and omap4
 619  * This function makes sure that an empty rx fifo is not read on these silicons
 620  * (OMAP1/2/3430 are not affected)
 621  */
 622 static unsigned int serial_in_override(struct uart_port *up, int offset)
 623 {
 624         if (UART_RX == offset) {
 625                 unsigned int lsr;
 626                 lsr = __serial_read_reg(up, UART_LSR);
 627                 if (!(lsr & UART_LSR_DR))
 628                         return -EPERM;
 629         }
 630
 631         return __serial_read_reg(up, offset);
 632 }
 633
 634 static void serial_out_override(struct uart_port *up, int offset, int value)
 635 {
 636         unsigned int status, tmout = 10000;
 637
 638         status = __serial_read_reg(up, UART_LSR);
 639         while (!(status & UART_LSR_THRE)) {
 640                 /* Wait up to 10ms for the character(s) to be sent. */
 641                 if (--tmout == 0)
 642                         break;
 643                 udelay(1);
 644                 status = __serial_read_reg(up, UART_LSR);
 645         }
 646         __serial_write_reg(up, offset, value);
 647 }
 648 #endif
 649
 650 void __init omap_serial_early_init(void)
 651 {
 652         int i = 0;
 653
 654         do {
 655                 char oh_name[MAX_UART_HWMOD_NAME_LEN];
 656                 struct omap_hwmod *oh;
 657                 struct omap_uart_state *uart;
 658
 659                 snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN,
 660                          "uart%d", i + 1);
 661                 oh = omap_hwmod_lookup(oh_name);
 662                 if (!oh)
 663                         break;
 664
 665                 uart = kzalloc(sizeof(struct omap_uart_state), GFP_KERNEL);
 666                 if (WARN_ON(!uart))
 667                         return;
 668
 669                 uart->oh = oh;
 670                 uart->num = i++;
 671                 list_add_tail(&uart->node, &uart_list);
 672                 num_uarts++;
 673
 674                 /*
 675                  * NOTE: omap_hwmod_init() has not yet been called,
 676                  *       so no hwmod functions will work yet.
 677                  */
 678
 679                 /*
 680                  * During UART early init, device need to be probed
 681                  * to determine SoC specific init before omap_device
 682                  * is ready.  Therefore, don't allow idle here
 683                  */
 684                 uart->oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET;
 685         } while (1);
 686 }
 687
 688 /**
 689  * omap_serial_init_port() - initialize single serial port
 690  * @port: serial port number (0-3)
 691  *
 692  * This function initialies serial driver for given @port only.
 693  * Platforms can call this function instead of omap_serial_init()
 694  * if they don't plan to use all available UARTs as serial ports.
 695  *
 696  * Don't mix calls to omap_serial_init_port() and omap_serial_init(),
 697  * use only one of the two.
 698  */
 699 void __init omap_serial_init_port(int port)
 700 {
 701         struct omap_uart_state *uart;
 702         struct omap_hwmod *oh;
 703         struct omap_device *od;
 704         void *pdata = NULL;
 705         u32 pdata_size = 0;
 706         char *name;
 707 #ifndef CONFIG_SERIAL_OMAP
 708         struct plat_serial8250_port ports[2] = {
 709                 {},
 710                 {.flags = 0},
 711         };
 712         struct plat_serial8250_port *p = &ports[0];
 713 #else
 714         struct omap_uart_port_info omap_up;
 715 #endif
 716
 717         if (WARN_ON(port < 0))
 718                 return;
 719         if (WARN_ON(port >= num_uarts))
 720                 return;
 721
 722         list_for_each_entry(uart, &uart_list, node)
 723                 if (port == uart->num)
 724                         break;
 725
 726         oh = uart->oh;
 727         uart->dma_enabled = 0;
 728 #ifndef CONFIG_SERIAL_OMAP
 729         name = "serial8250";
 730
 731         /*
 732          * !! 8250 driver does not use standard IORESOURCE* It
 733          * has it's own custom pdata that can be taken from
 734          * the hwmod resource data.  But, this needs to be
 735          * done after the build.
 736          *
 737          * ?? does it have to be done before the register ??
 738          * YES, because platform_device_data_add() copies
 739          * pdata, it does not use a pointer.
 740          */
 741         p->flags = UPF_BOOT_AUTOCONF;
 742         p->iotype = UPIO_MEM;
 743         p->regshift = 2;
 744         p->uartclk = OMAP24XX_BASE_BAUD * 16;
 745         p->irq = oh->mpu_irqs[0].irq;
 746         p->mapbase = oh->slaves[0]->addr->pa_start;
 747         p->membase = omap_hwmod_get_mpu_rt_va(oh);
 748         p->irqflags = IRQF_SHARED;
 749         p->private_data = uart;
 750
 751         /*
 752          * omap44xx: Never read empty UART fifo
 753          * omap3xxx: Never read empty UART fifo on UARTs
 754          * with IP rev >=0x52
 755          */
 756         uart->regshift = p->regshift;
 757         uart->membase = p->membase;
 758         if (cpu_is_omap44xx())
 759                 uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
 760         else if ((serial_read_reg(uart, UART_OMAP_MVER) & 0xFF)
 761                         >= UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV)
 762                 uart->errata |= UART_ERRATA_FIFO_FULL_ABORT;
 763
 764         if (uart->errata & UART_ERRATA_FIFO_FULL_ABORT) {
 765                 p->serial_in = serial_in_override;
 766                 p->serial_out = serial_out_override;
 767         }
 768
 769         pdata = &ports[0];
 770         pdata_size = 2 * sizeof(struct plat_serial8250_port);
 771 #else
 772
 773         name = DRIVER_NAME;
 774
 775         omap_up.dma_enabled = uart->dma_enabled;
 776         omap_up.uartclk = OMAP24XX_BASE_BAUD * 16;
 777         omap_up.mapbase = oh->slaves[0]->addr->pa_start;
 778         omap_up.membase = omap_hwmod_get_mpu_rt_va(oh);
 779         omap_up.irqflags = IRQF_SHARED;
 780         omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
 781
 782         pdata = &omap_up;
 783         pdata_size = sizeof(struct omap_uart_port_info);
 784 #endif
 785
 786         if (WARN_ON(!oh))
 787                 return;
 788
 789         od = omap_device_build(name, uart->num, oh, pdata, pdata_size,
 790                                omap_uart_latency,
 791                                ARRAY_SIZE(omap_uart_latency), false);
 792         WARN(IS_ERR(od), "Could not build omap_device for %s: %s.\n",
 793              name, oh->name);
 794
 795         uart->irq = oh->mpu_irqs[0].irq;
 796         uart->regshift = 2;
 797         uart->mapbase = oh->slaves[0]->addr->pa_start;
 798         uart->membase = omap_hwmod_get_mpu_rt_va(oh);
 799         uart->pdev = &od->pdev;
 800
 801         oh->dev_attr = uart;
 802
 803         /*
 804          * Because of early UART probing, UART did not get idled
 805          * on init.  Now that omap_device is ready, ensure full idle
 806          * before doing omap_device_enable().
 807          */
 808         omap_hwmod_idle(uart->oh);
 809
 810         omap_device_enable(uart->pdev);
 811         omap_uart_idle_init(uart);
 812         omap_uart_reset(uart);
 813         omap_hwmod_enable_wakeup(uart->oh);
 814         omap_device_idle(uart->pdev);
 815
 816         /*
 817          * Need to block sleep long enough for interrupt driven
 818          * driver to start.  Console driver is in polling mode
 819          * so device needs to be kept enabled while polling driver
 820          * is in use.
 821          */
 822         if (uart->timeout)
 823                 uart->timeout = (30 * HZ);
 824         omap_uart_block_sleep(uart);
 825         uart->timeout = DEFAULT_TIMEOUT;
 826
 827         if ((cpu_is_omap34xx() && uart->padconf) ||
 828             (uart->wk_en && uart->wk_mask)) {
 829                 device_init_wakeup(&od->pdev.dev, true);
 830                 DEV_CREATE_FILE(&od->pdev.dev, &dev_attr_sleep_timeout);
 831         }
 832
 833         /* Enable the MDR1 errata for OMAP3 */
 834         if (cpu_is_omap34xx())
 835                 uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
 836 }
 837
 838 /**
 839  * omap_serial_init() - intialize all supported serial ports
 840  *
 841  * Initializes all available UARTs as serial ports. Platforms
 842  * can call this function when they want to have default behaviour
 843  * for serial ports (e.g initialize them all as serial ports).
 844  */
 845 void __init omap_serial_init(void)
 846 {
 847         struct omap_uart_state *uart;
 848
 849         list_for_each_entry(uart, &uart_list, node)
 850                 omap_serial_init_port(uart->num);
 851 }