2 * linux/arch/arm/mach-pxa/stargate2.c
5 * Created: Nov 05, 2002
6 * Copyright: Intel Corp.
8 * Modified 2009: Jonathan Cameron <jic23@cam.ac.uk>
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
15 #include <linux/init.h>
16 #include <linux/device.h>
17 #include <linux/interrupt.h>
18 #include <linux/sched.h>
19 #include <linux/bitops.h>
21 #include <linux/delay.h>
22 #include <linux/platform_device.h>
23 #include <linux/regulator/machine.h>
24 #include <linux/mtd/mtd.h>
25 #include <linux/mtd/plat-ram.h>
26 #include <linux/mtd/partitions.h>
28 #include <linux/i2c/pxa-i2c.h>
29 #include <linux/i2c/pcf857x.h>
30 #include <linux/platform_data/at24.h>
31 #include <linux/smc91x.h>
32 #include <linux/gpio.h>
33 #include <linux/leds.h>
35 #include <asm/types.h>
36 #include <asm/setup.h>
37 #include <asm/memory.h>
38 #include <asm/mach-types.h>
41 #include <asm/mach/arch.h>
42 #include <asm/mach/map.h>
43 #include <asm/mach/irq.h>
44 #include <asm/mach/flash.h>
47 #include <linux/platform_data/mmc-pxamci.h>
49 #include "pxa27x-udc.h"
50 #include <mach/smemc.h>
52 #include <linux/spi/spi.h>
53 #include <linux/spi/pxa2xx_spi.h>
54 #include <linux/mfd/da903x.h>
55 #include <linux/platform_data/sht15.h>
60 #define STARGATE_NR_IRQS (IRQ_BOARD_START + 8)
63 #define SG2_BT_RESET 81
66 #define SG2_GPIO_nSD_DETECT 90
67 #define SG2_SD_POWER_ENABLE 89
69 static unsigned long sg2_im2_unified_pin_config[] __initdata = {
70 /* Device Identification for wakeup*/
83 /* 802.15.4 radio - driver out of mainline */
84 GPIO22_GPIO, /* CC_RSTN */
85 GPIO114_GPIO, /* CC_FIFO */
86 GPIO116_GPIO, /* CC_CCA */
87 GPIO0_GPIO, /* CC_FIFOP */
88 GPIO16_GPIO, /* CCSFD */
89 GPIO115_GPIO, /* Power enable */
95 /* SSP 3 - 802.15.4 radio */
96 GPIO39_GPIO, /* Chip Select */
101 /* SSP 2 to daughter boards */
105 GPIO37_GPIO, /* chip select */
107 /* SSP 1 - to daughter boards */
108 GPIO24_GPIO, /* Chip Select */
113 /* BTUART Basic Connector*/
119 /* STUART - IM2 via debug board not sure on SG2*/
123 /* Basic sensor board */
124 GPIO96_GPIO, /* accelerometer interrupt */
125 GPIO99_GPIO, /* ADC interrupt */
131 /* Basic sensor board */
132 GPIO96_GPIO, /* accelerometer interrupt */
133 GPIO99_GPIO, /* ADC interrupt */
135 /* Connector pins specified as gpios */
136 GPIO94_GPIO, /* large basic connector pin 14 */
137 GPIO10_GPIO, /* large basic connector pin 23 */
140 static struct sht15_platform_data platform_data_sht15 = {
145 static struct platform_device sht15 = {
149 .platform_data = &platform_data_sht15,
153 static struct regulator_consumer_supply stargate2_sensor_3_con[] = {
154 REGULATOR_SUPPLY("vcc", "sht15"),
160 /* a mote connector? */
162 /* the CSR bluecore chip */
164 /* The two voltages available to sensor boards */
167 /* directly connected to the pxa27x */
170 vcc_pxa_usim, /* Reference voltage for certain gpios */
173 vcc_pxa_core, /*Dc-Dc buck not yet supported */
176 vcc_bbio, /*not sure!*/
177 vcc_io, /* cc2420 802.15.4 radio and pxa vcc_io ?*/
180 /* The values of the various regulator constraints are obviously dependent
181 * on exactly what is wired to each ldo. Unfortunately this information is
182 * not generally available. More information has been requested from Xbow.
184 static struct regulator_init_data stargate2_ldo_init_data[] = {
186 .constraints = { /* board default 1.8V */
193 .constraints = { /* board default 2.8V */
200 .constraints = {/* default is 1.8V */
201 .name = "vcc_pxa_flash",
206 [vcc_cc2420] = { /* also vcc_io */
208 /* board default is 2.8V */
209 .name = "vcc_cc2420",
214 [vcc_vref] = { /* Reference for what? */
215 .constraints = { /* default 1.8V */
222 .constraints = { /* default 2.8V */
223 .name = "vcc_sram_ext",
229 .constraints = { /* default 2.8V */
236 .constraints = { /* default 2.8V */
243 .constraints = { /* default 2.8V */
249 [vcc_io] = { /* Same or higher than everything
250 * bar vccbat and vccusb */
251 .constraints = { /* default 2.8V */
258 .constraints = { /* default 1.8V */
259 .name = "vcc_sensor_1_8",
264 [vcc_sensor_3] = { /* curiously default 2.8V */
266 .name = "vcc_sensor_3",
270 .num_consumer_supplies = ARRAY_SIZE(stargate2_sensor_3_con),
271 .consumer_supplies = stargate2_sensor_3_con,
273 [vcc_pxa_pll] = { /* 1.17V - 1.43V, default 1.3V*/
275 .name = "vcc_pxa_pll",
281 .constraints = { /* default 1.8V */
282 .name = "vcc_pxa_usim",
288 .constraints = { /* default 1.8V */
289 .name = "vcc_pxa_mem",
296 static struct mtd_partition stargate2flash_partitions[] = {
298 .name = "Bootloader",
305 .offset = 0x00040000,
308 .name = "Filesystem",
310 .offset = 0x00240000,
315 static struct resource flash_resources = {
316 .start = PXA_CS0_PHYS,
317 .end = PXA_CS0_PHYS + SZ_32M - 1,
318 .flags = IORESOURCE_MEM,
321 static struct flash_platform_data stargate2_flash_data = {
322 .map_name = "cfi_probe",
323 .parts = stargate2flash_partitions,
324 .nr_parts = ARRAY_SIZE(stargate2flash_partitions),
325 .name = "PXA27xOnChipROM",
329 static struct platform_device stargate2_flash_device = {
330 .name = "pxa2xx-flash",
333 .platform_data = &stargate2_flash_data,
335 .resource = &flash_resources,
339 static struct pxa2xx_spi_master pxa_ssp_master_0_info = {
343 static struct pxa2xx_spi_master pxa_ssp_master_1_info = {
347 static struct pxa2xx_spi_master pxa_ssp_master_2_info = {
351 /* An upcoming kernel change will scrap SFRM usage so these
352 * drivers have been moved to use gpio's via cs_control */
353 static struct pxa2xx_spi_chip staccel_chip_info = {
361 static struct pxa2xx_spi_chip cc2420_info = {
369 static struct spi_board_info spi_board_info[] __initdata = {
371 .modalias = "lis3l02dq",
372 .max_speed_hz = 8000000,/* 8MHz max spi frequency at 3V */
375 .controller_data = &staccel_chip_info,
376 .irq = PXA_GPIO_TO_IRQ(96),
378 .modalias = "cc2420",
379 .max_speed_hz = 6500000,
382 .controller_data = &cc2420_info,
386 static void sg2_udc_command(int cmd)
389 case PXA2XX_UDC_CMD_CONNECT:
390 UP2OCR |= UP2OCR_HXOE | UP2OCR_DPPUE | UP2OCR_DPPUBE;
392 case PXA2XX_UDC_CMD_DISCONNECT:
393 UP2OCR &= ~(UP2OCR_HXOE | UP2OCR_DPPUE | UP2OCR_DPPUBE);
398 static struct i2c_pxa_platform_data i2c_pwr_pdata = {
402 static struct i2c_pxa_platform_data i2c_pdata = {
406 static void __init imote2_stargate2_init(void)
409 pxa2xx_mfp_config(ARRAY_AND_SIZE(sg2_im2_unified_pin_config));
411 pxa_set_ffuart_info(NULL);
412 pxa_set_btuart_info(NULL);
413 pxa_set_stuart_info(NULL);
415 pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
416 pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
417 pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
418 spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
421 pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
422 pxa_set_i2c_info(&i2c_pdata);
425 #ifdef CONFIG_MACH_INTELMOTE2
426 /* As the the imote2 doesn't currently have a conventional SD slot
427 * there is no option to hotplug cards, making all this rather simple
429 static int imote2_mci_get_ro(struct device *dev)
434 /* Rather simple case as hotplugging not possible */
435 static struct pxamci_platform_data imote2_mci_platform_data = {
436 .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
437 .get_ro = imote2_mci_get_ro,
438 .gpio_card_detect = -1,
443 static struct gpio_led imote2_led_pins[] = {
445 .name = "imote2:red",
449 .name = "imote2:green",
453 .name = "imote2:blue",
459 static struct gpio_led_platform_data imote2_led_data = {
460 .num_leds = ARRAY_SIZE(imote2_led_pins),
461 .leds = imote2_led_pins,
464 static struct platform_device imote2_leds = {
468 .platform_data = &imote2_led_data,
472 static struct da903x_subdev_info imote2_da9030_subdevs[] = {
474 .name = "da903x-regulator",
475 .id = DA9030_ID_LDO2,
476 .platform_data = &stargate2_ldo_init_data[vcc_bbio],
478 .name = "da903x-regulator",
479 .id = DA9030_ID_LDO3,
480 .platform_data = &stargate2_ldo_init_data[vcc_bb],
482 .name = "da903x-regulator",
483 .id = DA9030_ID_LDO4,
484 .platform_data = &stargate2_ldo_init_data[vcc_pxa_flash],
486 .name = "da903x-regulator",
487 .id = DA9030_ID_LDO5,
488 .platform_data = &stargate2_ldo_init_data[vcc_cc2420],
490 .name = "da903x-regulator",
491 .id = DA9030_ID_LDO6,
492 .platform_data = &stargate2_ldo_init_data[vcc_vref],
494 .name = "da903x-regulator",
495 .id = DA9030_ID_LDO7,
496 .platform_data = &stargate2_ldo_init_data[vcc_sram_ext],
498 .name = "da903x-regulator",
499 .id = DA9030_ID_LDO8,
500 .platform_data = &stargate2_ldo_init_data[vcc_mica],
502 .name = "da903x-regulator",
503 .id = DA9030_ID_LDO9,
504 .platform_data = &stargate2_ldo_init_data[vcc_bt],
506 .name = "da903x-regulator",
507 .id = DA9030_ID_LDO10,
508 .platform_data = &stargate2_ldo_init_data[vcc_sensor_1_8],
510 .name = "da903x-regulator",
511 .id = DA9030_ID_LDO11,
512 .platform_data = &stargate2_ldo_init_data[vcc_sensor_3],
514 .name = "da903x-regulator",
515 .id = DA9030_ID_LDO12,
516 .platform_data = &stargate2_ldo_init_data[vcc_lcd],
518 .name = "da903x-regulator",
519 .id = DA9030_ID_LDO15,
520 .platform_data = &stargate2_ldo_init_data[vcc_pxa_pll],
522 .name = "da903x-regulator",
523 .id = DA9030_ID_LDO17,
524 .platform_data = &stargate2_ldo_init_data[vcc_pxa_usim],
526 .name = "da903x-regulator", /*pxa vcc i/o and cc2420 vcc i/o */
527 .id = DA9030_ID_LDO18,
528 .platform_data = &stargate2_ldo_init_data[vcc_io],
530 .name = "da903x-regulator",
531 .id = DA9030_ID_LDO19,
532 .platform_data = &stargate2_ldo_init_data[vcc_pxa_mem],
536 static struct da903x_platform_data imote2_da9030_pdata = {
537 .num_subdevs = ARRAY_SIZE(imote2_da9030_subdevs),
538 .subdevs = imote2_da9030_subdevs,
541 static struct i2c_board_info __initdata imote2_pwr_i2c_board_info[] = {
545 .platform_data = &imote2_da9030_pdata,
546 .irq = PXA_GPIO_TO_IRQ(1),
550 static struct i2c_board_info __initdata imote2_i2c_board_info[] = {
551 { /* UCAM sensor board */
554 }, { /* ITS400 Sensor board only */
557 /* Through a nand gate - Also beware, on V2 sensor board the
558 * pull up resistors are missing.
560 .irq = PXA_GPIO_TO_IRQ(99),
561 }, { /* ITS400 Sensor board only */
564 /* Through a nand gate - Also beware, on V2 sensor board the
565 * pull up resistors are missing.
567 .irq = PXA_GPIO_TO_IRQ(99),
568 }, { /* ITS400 Sensor board only */
571 .irq = PXA_GPIO_TO_IRQ(96),
572 }, { /* IMB400 Multimedia board */
578 static unsigned long imote2_pin_config[] __initdata = {
584 GPIO103_GPIO, /* red led */
585 GPIO104_GPIO, /* green led */
586 GPIO105_GPIO, /* blue led */
589 static struct pxa2xx_udc_mach_info imote2_udc_info __initdata = {
590 .udc_command = sg2_udc_command,
593 static struct platform_device imote2_audio_device = {
594 .name = "imote2-audio",
598 static struct platform_device *imote2_devices[] = {
599 &stargate2_flash_device,
602 &imote2_audio_device,
605 static void __init imote2_init(void)
607 pxa2xx_mfp_config(ARRAY_AND_SIZE(imote2_pin_config));
609 imote2_stargate2_init();
611 platform_add_devices(imote2_devices, ARRAY_SIZE(imote2_devices));
613 i2c_register_board_info(0, imote2_i2c_board_info,
614 ARRAY_SIZE(imote2_i2c_board_info));
615 i2c_register_board_info(1, imote2_pwr_i2c_board_info,
616 ARRAY_SIZE(imote2_pwr_i2c_board_info));
618 pxa_set_mci_info(&imote2_mci_platform_data);
619 pxa_set_udc_info(&imote2_udc_info);
623 #ifdef CONFIG_MACH_STARGATE2
625 static unsigned long stargate2_pin_config[] __initdata = {
627 GPIO15_nCS_1, /* SRAM */
630 GPIO40_GPIO, /*cable detect?*/
633 GPIO91_GPIO | WAKEUP_ON_LEVEL_HIGH,
646 GPIO120_GPIO, /* Buff ctrl */
647 GPIO108_GPIO, /* Power ctrl */
648 GPIO82_GPIO, /* Reset */
649 GPIO53_GPIO, /* SG2_S0_GPIO_DETECT */
651 /* MMC not shared with imote2 */
652 GPIO90_GPIO, /* nSD detect */
653 GPIO89_GPIO, /* SD_POWER_ENABLE */
656 GPIO81_GPIO, /* reset */
659 static struct resource smc91x_resources[] = {
661 .name = "smc91x-regs",
662 .start = (PXA_CS4_PHYS + 0x300),
663 .end = (PXA_CS4_PHYS + 0xfffff),
664 .flags = IORESOURCE_MEM,
667 .start = PXA_GPIO_TO_IRQ(40),
668 .end = PXA_GPIO_TO_IRQ(40),
669 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
673 static struct smc91x_platdata stargate2_smc91x_info = {
674 .flags = SMC91X_USE_8BIT | SMC91X_USE_16BIT | SMC91X_USE_32BIT
675 | SMC91X_NOWAIT | SMC91X_USE_DMA,
678 static struct platform_device smc91x_device = {
681 .num_resources = ARRAY_SIZE(smc91x_resources),
682 .resource = smc91x_resources,
684 .platform_data = &stargate2_smc91x_info,
690 * The card detect interrupt isn't debounced so we delay it by 250ms
691 * to give the card a chance to fully insert / eject.
693 static int stargate2_mci_init(struct device *dev,
694 irq_handler_t stargate2_detect_int,
699 err = gpio_request(SG2_SD_POWER_ENABLE, "SG2_sd_power_enable");
701 printk(KERN_ERR "Can't get the gpio for SD power control");
704 gpio_direction_output(SG2_SD_POWER_ENABLE, 0);
706 err = gpio_request(SG2_GPIO_nSD_DETECT, "SG2_sd_detect");
708 printk(KERN_ERR "Can't get the sd detect gpio");
711 gpio_direction_input(SG2_GPIO_nSD_DETECT);
713 err = request_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT),
714 stargate2_detect_int,
719 printk(KERN_ERR "can't request MMC card detect IRQ\n");
720 goto free_nsd_detect;
725 gpio_free(SG2_GPIO_nSD_DETECT);
727 gpio_free(SG2_SD_POWER_ENABLE);
733 * stargate2_mci_setpower() - set state of mmc power supply
735 * Very simple control. Either it is on or off and is controlled by
737 static int stargate2_mci_setpower(struct device *dev, unsigned int vdd)
739 gpio_set_value(SG2_SD_POWER_ENABLE, !!vdd);
743 static void stargate2_mci_exit(struct device *dev, void *data)
745 free_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT), data);
746 gpio_free(SG2_SD_POWER_ENABLE);
747 gpio_free(SG2_GPIO_nSD_DETECT);
750 static struct pxamci_platform_data stargate2_mci_platform_data = {
751 .detect_delay_ms = 250,
752 .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
753 .init = stargate2_mci_init,
754 .setpower = stargate2_mci_setpower,
755 .exit = stargate2_mci_exit,
760 * SRAM - The Stargate 2 has 32MB of SRAM.
762 * Here it is made available as an MTD. This will then
763 * typically have a cifs filesystem created on it to provide
764 * fast temporary storage.
766 static struct resource sram_resources = {
767 .start = PXA_CS1_PHYS,
768 .end = PXA_CS1_PHYS + SZ_32M-1,
769 .flags = IORESOURCE_MEM,
772 static struct platdata_mtd_ram stargate2_sram_pdata = {
773 .mapname = "Stargate2 SRAM",
777 static struct platform_device stargate2_sram = {
780 .resource = &sram_resources,
783 .platform_data = &stargate2_sram_pdata,
787 static struct pcf857x_platform_data platform_data_pcf857x = {
795 static struct at24_platform_data pca9500_eeprom_pdata = {
801 * stargate2_reset_bluetooth() reset the bluecore to ensure consistent state
803 static int stargate2_reset_bluetooth(void)
806 err = gpio_request(SG2_BT_RESET, "SG2_BT_RESET");
808 printk(KERN_ERR "Could not get gpio for bluetooth reset\n");
811 gpio_direction_output(SG2_BT_RESET, 1);
813 /* now reset it - 5 msec minimum */
814 gpio_set_value(SG2_BT_RESET, 0);
816 gpio_set_value(SG2_BT_RESET, 1);
817 gpio_free(SG2_BT_RESET);
821 static struct led_info stargate2_leds[] = {
824 .flags = DA9030_LED_RATE_ON,
827 .flags = DA9030_LED_RATE_ON,
830 .flags = DA9030_LED_RATE_ON,
834 static struct da903x_subdev_info stargate2_da9030_subdevs[] = {
836 .name = "da903x-led",
837 .id = DA9030_ID_LED_2,
838 .platform_data = &stargate2_leds[0],
840 .name = "da903x-led",
841 .id = DA9030_ID_LED_3,
842 .platform_data = &stargate2_leds[2],
844 .name = "da903x-led",
845 .id = DA9030_ID_LED_4,
846 .platform_data = &stargate2_leds[1],
848 .name = "da903x-regulator",
849 .id = DA9030_ID_LDO2,
850 .platform_data = &stargate2_ldo_init_data[vcc_bbio],
852 .name = "da903x-regulator",
853 .id = DA9030_ID_LDO3,
854 .platform_data = &stargate2_ldo_init_data[vcc_bb],
856 .name = "da903x-regulator",
857 .id = DA9030_ID_LDO4,
858 .platform_data = &stargate2_ldo_init_data[vcc_pxa_flash],
860 .name = "da903x-regulator",
861 .id = DA9030_ID_LDO5,
862 .platform_data = &stargate2_ldo_init_data[vcc_cc2420],
864 .name = "da903x-regulator",
865 .id = DA9030_ID_LDO6,
866 .platform_data = &stargate2_ldo_init_data[vcc_vref],
868 .name = "da903x-regulator",
869 .id = DA9030_ID_LDO7,
870 .platform_data = &stargate2_ldo_init_data[vcc_sram_ext],
872 .name = "da903x-regulator",
873 .id = DA9030_ID_LDO8,
874 .platform_data = &stargate2_ldo_init_data[vcc_mica],
876 .name = "da903x-regulator",
877 .id = DA9030_ID_LDO9,
878 .platform_data = &stargate2_ldo_init_data[vcc_bt],
880 .name = "da903x-regulator",
881 .id = DA9030_ID_LDO10,
882 .platform_data = &stargate2_ldo_init_data[vcc_sensor_1_8],
884 .name = "da903x-regulator",
885 .id = DA9030_ID_LDO11,
886 .platform_data = &stargate2_ldo_init_data[vcc_sensor_3],
888 .name = "da903x-regulator",
889 .id = DA9030_ID_LDO12,
890 .platform_data = &stargate2_ldo_init_data[vcc_lcd],
892 .name = "da903x-regulator",
893 .id = DA9030_ID_LDO15,
894 .platform_data = &stargate2_ldo_init_data[vcc_pxa_pll],
896 .name = "da903x-regulator",
897 .id = DA9030_ID_LDO17,
898 .platform_data = &stargate2_ldo_init_data[vcc_pxa_usim],
900 .name = "da903x-regulator", /*pxa vcc i/o and cc2420 vcc i/o */
901 .id = DA9030_ID_LDO18,
902 .platform_data = &stargate2_ldo_init_data[vcc_io],
904 .name = "da903x-regulator",
905 .id = DA9030_ID_LDO19,
906 .platform_data = &stargate2_ldo_init_data[vcc_pxa_mem],
910 static struct da903x_platform_data stargate2_da9030_pdata = {
911 .num_subdevs = ARRAY_SIZE(stargate2_da9030_subdevs),
912 .subdevs = stargate2_da9030_subdevs,
915 static struct i2c_board_info __initdata stargate2_pwr_i2c_board_info[] = {
919 .platform_data = &stargate2_da9030_pdata,
920 .irq = PXA_GPIO_TO_IRQ(1),
924 static struct i2c_board_info __initdata stargate2_i2c_board_info[] = {
925 /* Techically this a pca9500 - but it's compatible with the 8574
926 * for gpio expansion and the 24c02 for eeprom access.
931 .platform_data = &platform_data_pcf857x,
935 .platform_data = &pca9500_eeprom_pdata,
939 }, { /* ITS400 Sensor board only */
942 /* Through a nand gate - Also beware, on V2 sensor board the
943 * pull up resistors are missing.
945 .irq = PXA_GPIO_TO_IRQ(99),
946 }, { /* ITS400 Sensor board only */
949 /* Through a nand gate - Also beware, on V2 sensor board the
950 * pull up resistors are missing.
952 .irq = PXA_GPIO_TO_IRQ(99),
953 }, { /* ITS400 Sensor board only */
956 .irq = PXA_GPIO_TO_IRQ(96),
960 /* Board doesn't support cable detection - so always lie and say
961 * something is there.
963 static int sg2_udc_detect(void)
968 static struct pxa2xx_udc_mach_info stargate2_udc_info __initdata = {
969 .udc_is_connected = sg2_udc_detect,
970 .udc_command = sg2_udc_command,
973 static struct platform_device *stargate2_devices[] = {
974 &stargate2_flash_device,
980 static void __init stargate2_init(void)
982 /* This is probably a board specific hack as this must be set
983 prior to connecting the MFP stuff up. */
984 __raw_writel(__raw_readl(MECR) & ~MECR_NOS, MECR);
986 pxa2xx_mfp_config(ARRAY_AND_SIZE(stargate2_pin_config));
988 imote2_stargate2_init();
990 platform_add_devices(ARRAY_AND_SIZE(stargate2_devices));
992 i2c_register_board_info(0, ARRAY_AND_SIZE(stargate2_i2c_board_info));
993 i2c_register_board_info(1, stargate2_pwr_i2c_board_info,
994 ARRAY_SIZE(stargate2_pwr_i2c_board_info));
996 pxa_set_mci_info(&stargate2_mci_platform_data);
998 pxa_set_udc_info(&stargate2_udc_info);
1000 stargate2_reset_bluetooth();
1004 #ifdef CONFIG_MACH_INTELMOTE2
1005 MACHINE_START(INTELMOTE2, "IMOTE 2")
1006 .map_io = pxa27x_map_io,
1007 .nr_irqs = PXA_NR_IRQS,
1008 .init_irq = pxa27x_init_irq,
1009 .handle_irq = pxa27x_handle_irq,
1010 .init_time = pxa_timer_init,
1011 .init_machine = imote2_init,
1012 .atag_offset = 0x100,
1013 .restart = pxa_restart,
1017 #ifdef CONFIG_MACH_STARGATE2
1018 MACHINE_START(STARGATE2, "Stargate 2")
1019 .map_io = pxa27x_map_io,
1020 .nr_irqs = STARGATE_NR_IRQS,
1021 .init_irq = pxa27x_init_irq,
1022 .handle_irq = pxa27x_handle_irq,
1023 .init_time = pxa_timer_init,
1024 .init_machine = stargate2_init,
1025 .atag_offset = 0x100,
1026 .restart = pxa_restart,