1 /* File: arch/blackfin/mach-bf527/boards/tll6527m.c
2 * Based on: arch/blackfin/mach-bf527/boards/ezkit.c
5 * Copyright: 2010 - The Learning Labs Inc.
7 * Licensed under the GPL-2 or later.
10 #include <linux/device.h>
11 #include <linux/platform_device.h>
12 #include <linux/mtd/mtd.h>
13 #include <linux/mtd/partitions.h>
14 #include <linux/mtd/physmap.h>
15 #include <linux/spi/spi.h>
16 #include <linux/spi/flash.h>
17 #include <linux/i2c.h>
18 #include <linux/irq.h>
19 #include <linux/interrupt.h>
20 #include <linux/usb/musb.h>
21 #include <linux/leds.h>
22 #include <linux/input.h>
24 #include <asm/bfin5xx_spi.h>
25 #include <asm/reboot.h>
27 #include <asm/portmux.h>
30 #if defined(CONFIG_TOUCHSCREEN_AD7879) \
31 || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
32 #include <linux/spi/ad7879.h>
33 #define LCD_BACKLIGHT_GPIO 0x40
34 /* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
35 * LCD Backlight Enable
40 * Name the Board for the /proc/cpuinfo
42 const char bfin_board_name[] = "TLL6527M";
44 * Driver needs to know address, irq and flag pin.
47 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
48 static struct resource musb_resources[] = {
52 .flags = IORESOURCE_MEM,
54 [1] = { /* general IRQ */
55 .start = IRQ_USB_INT0,
57 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
62 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
66 static struct musb_hdrc_config musb_config = {
73 /*.gpio_vrsel = GPIO_PG13,*/
74 /* Some custom boards need to be active low, just set it to "0"
77 .gpio_vrsel_active = 1,
80 static struct musb_hdrc_platform_data musb_plat = {
81 #if defined(CONFIG_USB_MUSB_OTG)
83 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
85 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
86 .mode = MUSB_PERIPHERAL,
88 .config = &musb_config,
91 static u64 musb_dmamask = ~(u32)0;
93 static struct platform_device musb_device = {
94 .name = "musb-blackfin",
97 .dma_mask = &musb_dmamask,
98 .coherent_dma_mask = 0xffffffff,
99 .platform_data = &musb_plat,
101 .num_resources = ARRAY_SIZE(musb_resources),
102 .resource = musb_resources,
106 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
107 #include <asm/bfin-lq035q1.h>
109 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
110 .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
111 .ppi_mode = USE_RGB565_16_BIT_PPI,
113 .gpio_bl = LCD_BACKLIGHT_GPIO,
116 static struct resource bfin_lq035q1_resources[] = {
118 .start = IRQ_PPI_ERROR,
119 .end = IRQ_PPI_ERROR,
120 .flags = IORESOURCE_IRQ,
124 static struct platform_device bfin_lq035q1_device = {
125 .name = "bfin-lq035q1",
127 .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
128 .resource = bfin_lq035q1_resources,
130 .platform_data = &bfin_lq035q1_data,
135 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
136 static struct mtd_partition tll6527m_partitions[] = {
138 .name = "bootloader(nor)",
142 .name = "linux kernel(nor)",
144 .offset = MTDPART_OFS_APPEND,
146 .name = "file system(nor)",
147 .size = MTDPART_SIZ_FULL,
148 .offset = MTDPART_OFS_APPEND,
152 static struct physmap_flash_data tll6527m_flash_data = {
154 .parts = tll6527m_partitions,
155 .nr_parts = ARRAY_SIZE(tll6527m_partitions),
158 static unsigned tll6527m_flash_gpios[] = { GPIO_PG11, GPIO_PH11, GPIO_PH12 };
160 static struct resource tll6527m_flash_resource[] = {
165 .flags = IORESOURCE_MEM,
167 .start = (unsigned long)tll6527m_flash_gpios,
168 .end = ARRAY_SIZE(tll6527m_flash_gpios),
169 .flags = IORESOURCE_IRQ,
173 static struct platform_device tll6527m_flash_device = {
174 .name = "gpio-addr-flash",
177 .platform_data = &tll6527m_flash_data,
179 .num_resources = ARRAY_SIZE(tll6527m_flash_resource),
180 .resource = tll6527m_flash_resource,
184 #if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
185 /* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
186 * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
187 * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
188 * used as SPI CS lines, this should be > MAX_BLACKFIN_GPIOS
190 #include <linux/gpio-decoder.h>
191 #define EXP_GPIO_SPISEL_BASE 0x64
192 static unsigned gpio_addr_inputs[] = {
193 GPIO_PG1, GPIO_PH9, GPIO_PH10
196 static struct gpio_decoder_platform_data spi_decoded_cs = {
197 .base = EXP_GPIO_SPISEL_BASE,
198 .input_addrs = gpio_addr_inputs,
199 .nr_input_addrs = ARRAY_SIZE(gpio_addr_inputs),
201 /* .default_output = (1 << ARRAY_SIZE(gpio_addr_inputs)) - 1 */
204 static struct platform_device spi_decoded_gpio = {
205 .name = "gpio-decoder",
208 .platform_data = &spi_decoded_cs,
213 #define EXP_GPIO_SPISEL_BASE 0x0
217 #if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
218 #include <linux/input/adxl34x.h>
219 static const struct adxl34x_platform_data adxl345_info = {
223 .tap_threshold = 0x31,
224 .tap_duration = 0x10,
227 .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
228 .act_axis_control = 0xFF,
229 .activity_threshold = 5,
230 .inactivity_threshold = 2,
231 .inactivity_time = 2,
232 .free_fall_threshold = 0x7,
233 .free_fall_time = 0x20,
235 .data_range = ADXL_FULL_RES,
238 .ev_code_x = ABS_X, /* EV_REL */
239 .ev_code_y = ABS_Y, /* EV_REL */
240 .ev_code_z = ABS_Z, /* EV_REL */
242 .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
244 /* .ev_code_ff = KEY_F,*/ /* EV_KEY */
245 .ev_code_act_inactivity = KEY_A, /* EV_KEY */
247 .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
248 .fifo_mode = ADXL_FIFO_STREAM,
252 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
253 static struct platform_device rtc_device = {
259 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
260 #include <linux/bfin_mac.h>
261 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
263 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
266 .irq = IRQ_MAC_PHYINT,
270 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
272 .phydev_data = bfin_phydev_data,
273 .phy_mode = PHY_INTERFACE_MODE_RMII,
274 .mac_peripherals = bfin_mac_peripherals,
277 static struct platform_device bfin_mii_bus = {
278 .name = "bfin_mii_bus",
280 .platform_data = &bfin_mii_bus_data,
284 static struct platform_device bfin_mac_device = {
287 .platform_data = &bfin_mii_bus,
292 #if defined(CONFIG_MTD_M25P80) \
293 || defined(CONFIG_MTD_M25P80_MODULE)
294 static struct mtd_partition bfin_spi_flash_partitions[] = {
296 .name = "bootloader(spi)",
299 .mask_flags = MTD_CAP_ROM
301 .name = "linux kernel(spi)",
302 .size = MTDPART_SIZ_FULL,
303 .offset = MTDPART_OFS_APPEND,
307 static struct flash_platform_data bfin_spi_flash_data = {
309 .parts = bfin_spi_flash_partitions,
310 .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
314 /* SPI flash chip (m25p64) */
315 static struct bfin5xx_spi_chip spi_flash_chip_info = {
316 .enable_dma = 0, /* use dma transfer with this chip*/
321 #if defined(CONFIG_BFIN_SPI_ADC) \
322 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
324 static struct bfin5xx_spi_chip spi_adc_chip_info = {
325 .enable_dma = 0, /* use dma transfer with this chip*/
327 * tll6527m V1.0 does not support native spi slave selects
328 * hence DMA mode will not be useful since the ADC needs
329 * CS to toggle for each sample and cs_change_per_word
330 * seems to be removed from spi_bfin5xx.c
336 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
337 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
343 #if defined(CONFIG_TOUCHSCREEN_AD7879) \
344 || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
345 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
346 .model = 7879, /* Model = AD7879 */
347 .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
348 .pressure_max = 10000,
350 .first_conversion_delay = 3,
351 /* wait 512us before do a first conversion */
352 .acquisition_time = 1, /* 4us acquisition time per sample */
353 .median = 2, /* do 8 measurements */
355 /* take the average of 4 middle samples */
356 .pen_down_acc_interval = 255, /* 9.4 ms */
357 .gpio_export = 1, /* configure AUX as GPIO output*/
358 .gpio_base = LCD_BACKLIGHT_GPIO,
362 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
363 || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
364 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
370 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
371 static struct bfin5xx_spi_chip spidev_chip_info = {
377 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
378 static struct platform_device bfin_i2s = {
380 .id = CONFIG_SND_BF5XX_SPORT_NUM,
381 /* TODO: add platform data here */
385 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
386 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
392 #if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
393 static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
398 static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
403 #include <linux/spi/mcp23s08.h>
404 static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
405 .chip[0].is_present = true,
408 static const struct mcp23s08_platform_data bfin_mcp23s08_usr_gpio_info = {
409 .chip[2].is_present = true,
414 static struct spi_board_info bfin_spi_board_info[] __initdata = {
415 #if defined(CONFIG_MTD_M25P80) \
416 || defined(CONFIG_MTD_M25P80_MODULE)
418 /* the modalias must be the same as spi device driver name */
419 .modalias = "m25p80", /* Name of spi_driver for this device */
420 .max_speed_hz = 25000000,
421 /* max spi clock (SCK) speed in HZ */
422 .bus_num = 0, /* Framework bus number */
423 .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
424 /* Can be connected to TLL6527M GPIO connector */
425 /* Either SPI_ADC or M25P80 FLASH can be installed at a time */
426 .platform_data = &bfin_spi_flash_data,
427 .controller_data = &spi_flash_chip_info,
432 #if defined(CONFIG_BFIN_SPI_ADC)
433 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
435 .modalias = "bfin_spi_adc",
436 /* Name of spi_driver for this device */
437 .max_speed_hz = 10000000,
438 /* max spi clock (SCK) speed in HZ */
439 .bus_num = 0, /* Framework bus number */
440 .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
441 /* Framework chip select. */
442 .platform_data = NULL, /* No spi_driver specific config */
443 .controller_data = &spi_adc_chip_info,
448 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
450 .modalias = "mmc_spi",
452 * TLL6527M V1.0 does not support SD Card at SPI Clock > 10 MHz due to
453 * SPI buffer limitations
455 .max_speed_hz = 10000000,
456 /* max spi clock (SCK) speed in HZ */
458 .chip_select = EXP_GPIO_SPISEL_BASE + 0x05 + MAX_CTRL_CS,
459 .controller_data = &mmc_spi_chip_info,
463 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
464 || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
466 .modalias = "ad7879",
467 .platform_data = &bfin_ad7879_ts_info,
469 .max_speed_hz = 5000000,
470 /* max spi clock (SCK) speed in HZ */
472 .chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
473 .controller_data = &spi_ad7879_chip_info,
474 .mode = SPI_CPHA | SPI_CPOL,
477 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
479 .modalias = "spidev",
480 .max_speed_hz = 10000000,
481 /* TLL6527Mv1-0 supports max spi clock (SCK) speed = 10 MHz */
483 .chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
484 .mode = SPI_CPHA | SPI_CPOL,
485 .controller_data = &spidev_chip_info,
488 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
490 .modalias = "bfin-lq035q1-spi",
491 .max_speed_hz = 20000000,
493 .chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
494 .controller_data = &lq035q1_spi_chip_info,
495 .mode = SPI_CPHA | SPI_CPOL,
498 #if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
500 .modalias = "mcp23s08",
501 .platform_data = &bfin_mcp23s08_sys_gpio_info,
502 .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
504 .chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
505 .controller_data = &spi_mcp23s08_sys_chip_info,
506 .mode = SPI_CPHA | SPI_CPOL,
509 .modalias = "mcp23s08",
510 .platform_data = &bfin_mcp23s08_usr_gpio_info,
511 .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
513 .chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
514 .controller_data = &spi_mcp23s08_usr_chip_info,
515 .mode = SPI_CPHA | SPI_CPOL,
520 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
521 /* SPI controller data */
522 static struct bfin5xx_spi_master bfin_spi0_info = {
523 .num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
524 /* EXP_GPIO_SPISEL_BASE will be > MAX_BLACKFIN_GPIOS */
525 .enable_dma = 1, /* master has the ability to do dma transfer */
526 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
530 static struct resource bfin_spi0_resource[] = {
532 .start = SPI0_REGBASE,
533 .end = SPI0_REGBASE + 0xFF,
534 .flags = IORESOURCE_MEM,
539 .flags = IORESOURCE_DMA,
544 .flags = IORESOURCE_IRQ,
548 static struct platform_device bfin_spi0_device = {
550 .id = 0, /* Bus number */
551 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
552 .resource = bfin_spi0_resource,
554 .platform_data = &bfin_spi0_info, /* Passed to driver */
557 #endif /* spi master and devices */
559 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
560 #ifdef CONFIG_SERIAL_BFIN_UART0
561 static struct resource bfin_uart0_resources[] = {
565 .flags = IORESOURCE_MEM,
568 .start = IRQ_UART0_RX,
569 .end = IRQ_UART0_RX+1,
570 .flags = IORESOURCE_IRQ,
573 .start = IRQ_UART0_ERROR,
574 .end = IRQ_UART0_ERROR,
575 .flags = IORESOURCE_IRQ,
578 .start = CH_UART0_TX,
580 .flags = IORESOURCE_DMA,
583 .start = CH_UART0_RX,
585 .flags = IORESOURCE_DMA,
589 static unsigned short bfin_uart0_peripherals[] = {
590 P_UART0_TX, P_UART0_RX, 0
593 static struct platform_device bfin_uart0_device = {
596 .num_resources = ARRAY_SIZE(bfin_uart0_resources),
597 .resource = bfin_uart0_resources,
599 .platform_data = &bfin_uart0_peripherals,
600 /* Passed to driver */
604 #ifdef CONFIG_SERIAL_BFIN_UART1
605 static struct resource bfin_uart1_resources[] = {
609 .flags = IORESOURCE_MEM,
612 .start = IRQ_UART1_RX,
613 .end = IRQ_UART1_RX+1,
614 .flags = IORESOURCE_IRQ,
617 .start = IRQ_UART1_ERROR,
618 .end = IRQ_UART1_ERROR,
619 .flags = IORESOURCE_IRQ,
622 .start = CH_UART1_TX,
624 .flags = IORESOURCE_DMA,
627 .start = CH_UART1_RX,
629 .flags = IORESOURCE_DMA,
631 #ifdef CONFIG_BFIN_UART1_CTSRTS
635 .flags = IORESOURCE_IO,
640 .flags = IORESOURCE_IO,
645 static unsigned short bfin_uart1_peripherals[] = {
646 P_UART1_TX, P_UART1_RX, 0
649 static struct platform_device bfin_uart1_device = {
652 .num_resources = ARRAY_SIZE(bfin_uart1_resources),
653 .resource = bfin_uart1_resources,
655 .platform_data = &bfin_uart1_peripherals,
656 /* Passed to driver */
662 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
663 #ifdef CONFIG_BFIN_SIR0
664 static struct resource bfin_sir0_resources[] = {
668 .flags = IORESOURCE_MEM,
671 .start = IRQ_UART0_RX,
672 .end = IRQ_UART0_RX+1,
673 .flags = IORESOURCE_IRQ,
676 .start = CH_UART0_RX,
677 .end = CH_UART0_RX+1,
678 .flags = IORESOURCE_DMA,
682 static struct platform_device bfin_sir0_device = {
685 .num_resources = ARRAY_SIZE(bfin_sir0_resources),
686 .resource = bfin_sir0_resources,
689 #ifdef CONFIG_BFIN_SIR1
690 static struct resource bfin_sir1_resources[] = {
694 .flags = IORESOURCE_MEM,
697 .start = IRQ_UART1_RX,
698 .end = IRQ_UART1_RX+1,
699 .flags = IORESOURCE_IRQ,
702 .start = CH_UART1_RX,
703 .end = CH_UART1_RX+1,
704 .flags = IORESOURCE_DMA,
708 static struct platform_device bfin_sir1_device = {
711 .num_resources = ARRAY_SIZE(bfin_sir1_resources),
712 .resource = bfin_sir1_resources,
717 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
718 static struct resource bfin_twi0_resource[] = {
720 .start = TWI0_REGBASE,
722 .flags = IORESOURCE_MEM,
727 .flags = IORESOURCE_IRQ,
731 static struct platform_device i2c_bfin_twi_device = {
732 .name = "i2c-bfin-twi",
734 .num_resources = ARRAY_SIZE(bfin_twi0_resource),
735 .resource = bfin_twi0_resource,
739 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
740 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
742 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
746 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
748 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
751 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
752 || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
754 I2C_BOARD_INFO("ad7879", 0x2C),
756 .platform_data = (void *)&bfin_ad7879_ts_info,
759 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
761 I2C_BOARD_INFO("ssm2602", 0x1b),
765 I2C_BOARD_INFO("adm1192", 0x2e),
769 I2C_BOARD_INFO("ltc3576", 0x09),
771 #if defined(CONFIG_INPUT_ADXL34X_I2C) \
772 || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
774 I2C_BOARD_INFO("adxl34x", 0x53),
776 .platform_data = (void *)&adxl345_info,
781 #if defined(CONFIG_SERIAL_BFIN_SPORT) \
782 || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
783 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
784 static struct resource bfin_sport0_uart_resources[] = {
786 .start = SPORT0_TCR1,
787 .end = SPORT0_MRCS3+4,
788 .flags = IORESOURCE_MEM,
791 .start = IRQ_SPORT0_RX,
792 .end = IRQ_SPORT0_RX+1,
793 .flags = IORESOURCE_IRQ,
796 .start = IRQ_SPORT0_ERROR,
797 .end = IRQ_SPORT0_ERROR,
798 .flags = IORESOURCE_IRQ,
802 static unsigned short bfin_sport0_peripherals[] = {
803 P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
804 P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
807 static struct platform_device bfin_sport0_uart_device = {
808 .name = "bfin-sport-uart",
810 .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
811 .resource = bfin_sport0_uart_resources,
813 .platform_data = &bfin_sport0_peripherals,
814 /* Passed to driver */
818 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
819 static struct resource bfin_sport1_uart_resources[] = {
821 .start = SPORT1_TCR1,
822 .end = SPORT1_MRCS3+4,
823 .flags = IORESOURCE_MEM,
826 .start = IRQ_SPORT1_RX,
827 .end = IRQ_SPORT1_RX+1,
828 .flags = IORESOURCE_IRQ,
831 .start = IRQ_SPORT1_ERROR,
832 .end = IRQ_SPORT1_ERROR,
833 .flags = IORESOURCE_IRQ,
837 static unsigned short bfin_sport1_peripherals[] = {
838 P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
839 P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
842 static struct platform_device bfin_sport1_uart_device = {
843 .name = "bfin-sport-uart",
845 .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
846 .resource = bfin_sport1_uart_resources,
848 .platform_data = &bfin_sport1_peripherals,
849 /* Passed to driver */
855 static const unsigned int cclk_vlev_datasheet[] = {
856 VRPAIR(VLEV_100, 400000000),
857 VRPAIR(VLEV_105, 426000000),
858 VRPAIR(VLEV_110, 500000000),
859 VRPAIR(VLEV_115, 533000000),
860 VRPAIR(VLEV_120, 600000000),
863 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
864 .tuple_tab = cclk_vlev_datasheet,
865 .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
866 .vr_settling_time = 25 /* us */,
869 static struct platform_device bfin_dpmc = {
872 .platform_data = &bfin_dmpc_vreg_data,
876 static struct platform_device *tll6527m_devices[] __initdata = {
880 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
884 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
888 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
893 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
897 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
898 &bfin_lq035q1_device,
901 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
902 #ifdef CONFIG_SERIAL_BFIN_UART0
905 #ifdef CONFIG_SERIAL_BFIN_UART1
910 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
911 #ifdef CONFIG_BFIN_SIR0
914 #ifdef CONFIG_BFIN_SIR1
919 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
920 &i2c_bfin_twi_device,
923 #if defined(CONFIG_SERIAL_BFIN_SPORT) \
924 || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
925 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
926 &bfin_sport0_uart_device,
928 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
929 &bfin_sport1_uart_device,
933 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
934 &tll6527m_flash_device,
937 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
941 #if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
946 static int __init tll6527m_init(void)
948 printk(KERN_INFO "%s(): registering device resources\n", __func__);
949 i2c_register_board_info(0, bfin_i2c_board_info,
950 ARRAY_SIZE(bfin_i2c_board_info));
951 platform_add_devices(tll6527m_devices, ARRAY_SIZE(tll6527m_devices));
952 spi_register_board_info(bfin_spi_board_info,
953 ARRAY_SIZE(bfin_spi_board_info));
957 arch_initcall(tll6527m_init);
959 static struct platform_device *tll6527m_early_devices[] __initdata = {
960 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
961 #ifdef CONFIG_SERIAL_BFIN_UART0
964 #ifdef CONFIG_SERIAL_BFIN_UART1
969 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
970 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
971 &bfin_sport0_uart_device,
973 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
974 &bfin_sport1_uart_device,
979 void __init native_machine_early_platform_add_devices(void)
981 printk(KERN_INFO "register early platform devices\n");
982 early_platform_add_devices(tll6527m_early_devices,
983 ARRAY_SIZE(tll6527m_early_devices));
986 void native_machine_restart(char *cmd)
988 /* workaround reboot hang when booting from SPI */
989 if ((bfin_read_SYSCR() & 0x7) == 0x3)
990 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
993 void bfin_get_ether_addr(char *addr)
995 /* the MAC is stored in OTP memory page 0xDF */
998 u32 (*otp_read)(u32 page, u32 flags,
999 u64 *page_content) = (void *)0xEF00001A;
1001 ret = otp_read(0xDF, 0x00, &otp_mac);
1003 char *otp_mac_p = (char *)&otp_mac;
1004 for (ret = 0; ret < 6; ++ret)
1005 addr[ret] = otp_mac_p[5 - ret];
1008 EXPORT_SYMBOL(bfin_get_ether_addr);