2 * Copyright 2004-2009 Analog Devices Inc.
3 * 2005 National ICT Australia (NICTA)
4 * Aidan Williams <aidan@nicta.com.au>
6 * Licensed under the GPL-2 or later.
9 #include <linux/device.h>
10 #include <linux/platform_device.h>
11 #include <linux/mtd/mtd.h>
12 #include <linux/mtd/partitions.h>
13 #include <linux/mtd/physmap.h>
14 #include <linux/spi/spi.h>
15 #include <linux/irq.h>
16 #include <linux/interrupt.h>
17 #include <linux/delay.h>
19 #include <asm/bfin5xx_spi.h>
20 #include <asm/portmux.h>
24 * Name the Board for the /proc/cpuinfo
26 const char bfin_board_name[] = "ADI BF561-EZKIT";
28 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
29 #include <linux/usb/isp1760.h>
30 static struct resource bfin_isp1760_resources[] = {
33 .end = 0x203C0000 + 0xfffff,
34 .flags = IORESOURCE_MEM,
39 .flags = IORESOURCE_IRQ,
43 static struct isp1760_platform_data isp1760_priv = {
48 .dack_polarity_high = 0,
49 .dreq_polarity_high = 0,
52 static struct platform_device bfin_isp1760_device = {
56 .platform_data = &isp1760_priv,
58 .num_resources = ARRAY_SIZE(bfin_isp1760_resources),
59 .resource = bfin_isp1760_resources,
63 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
64 #include <linux/usb/isp1362.h>
66 static struct resource isp1362_hcd_resources[] = {
70 .flags = IORESOURCE_MEM,
74 .flags = IORESOURCE_MEM,
78 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
82 static struct isp1362_platform_data isp1362_priv = {
87 .int_edge_triggered = 0,
88 .remote_wakeup_connected = 0,
89 .no_power_switching = 1,
90 .power_switching_mode = 0,
93 static struct platform_device isp1362_hcd_device = {
94 .name = "isp1362-hcd",
97 .platform_data = &isp1362_priv,
99 .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
100 .resource = isp1362_hcd_resources,
104 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
105 static struct resource net2272_bfin_resources[] = {
108 .end = 0x2C000000 + 0x7F,
109 .flags = IORESOURCE_MEM,
112 .flags = IORESOURCE_BUS,
116 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
120 static struct platform_device net2272_bfin_device = {
123 .num_resources = ARRAY_SIZE(net2272_bfin_resources),
124 .resource = net2272_bfin_resources,
129 * USB-LAN EzExtender board
130 * Driver needs to know address, irq and flag pin.
132 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
133 #include <linux/smc91x.h>
135 static struct smc91x_platdata smc91x_info = {
136 .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
137 .leda = RPC_LED_100_10,
138 .ledb = RPC_LED_TX_RX,
141 static struct resource smc91x_resources[] = {
143 .name = "smc91x-regs",
145 .end = 0x2C010300 + 16,
146 .flags = IORESOURCE_MEM,
151 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
155 static struct platform_device smc91x_device = {
158 .num_resources = ARRAY_SIZE(smc91x_resources),
159 .resource = smc91x_resources,
161 .platform_data = &smc91x_info,
166 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
167 #ifdef CONFIG_SERIAL_BFIN_UART0
168 static struct resource bfin_uart0_resources[] = {
170 .start = BFIN_UART_THR,
171 .end = BFIN_UART_GCTL+2,
172 .flags = IORESOURCE_MEM,
175 .start = IRQ_UART_TX,
177 .flags = IORESOURCE_IRQ,
180 .start = IRQ_UART_RX,
182 .flags = IORESOURCE_IRQ,
185 .start = IRQ_UART_ERROR,
186 .end = IRQ_UART_ERROR,
187 .flags = IORESOURCE_IRQ,
192 .flags = IORESOURCE_DMA,
197 .flags = IORESOURCE_DMA,
201 static unsigned short bfin_uart0_peripherals[] = {
202 P_UART0_TX, P_UART0_RX, 0
205 static struct platform_device bfin_uart0_device = {
208 .num_resources = ARRAY_SIZE(bfin_uart0_resources),
209 .resource = bfin_uart0_resources,
211 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
217 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
218 #ifdef CONFIG_BFIN_SIR0
219 static struct resource bfin_sir0_resources[] = {
223 .flags = IORESOURCE_MEM,
226 .start = IRQ_UART0_RX,
227 .end = IRQ_UART0_RX+1,
228 .flags = IORESOURCE_IRQ,
231 .start = CH_UART0_RX,
232 .end = CH_UART0_RX+1,
233 .flags = IORESOURCE_DMA,
237 static struct platform_device bfin_sir0_device = {
240 .num_resources = ARRAY_SIZE(bfin_sir0_resources),
241 .resource = bfin_sir0_resources,
246 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
247 static struct mtd_partition ezkit_partitions[] = {
249 .name = "bootloader(nor)",
253 .name = "linux kernel(nor)",
255 .offset = MTDPART_OFS_APPEND,
257 .name = "file system(nor)",
258 .size = 0x800000 - 0x40000 - 0x1C0000 - 0x2000 * 8,
259 .offset = MTDPART_OFS_APPEND,
261 .name = "config(nor)",
263 .offset = MTDPART_OFS_APPEND,
265 .name = "u-boot env(nor)",
267 .offset = MTDPART_OFS_APPEND,
271 static struct physmap_flash_data ezkit_flash_data = {
273 .parts = ezkit_partitions,
274 .nr_parts = ARRAY_SIZE(ezkit_partitions),
277 static struct resource ezkit_flash_resource = {
280 .flags = IORESOURCE_MEM,
283 static struct platform_device ezkit_flash_device = {
284 .name = "physmap-flash",
287 .platform_data = &ezkit_flash_data,
290 .resource = &ezkit_flash_resource,
294 #if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
296 static struct resource bfin_spi0_resource[] = {
298 .start = SPI0_REGBASE,
299 .end = SPI0_REGBASE + 0xFF,
300 .flags = IORESOURCE_MEM,
305 .flags = IORESOURCE_DMA,
310 .flags = IORESOURCE_IRQ,
314 /* SPI controller data */
315 static struct bfin5xx_spi_master bfin_spi0_info = {
317 .enable_dma = 1, /* master has the ability to do dma transfer */
318 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
321 static struct platform_device bfin_spi0_device = {
323 .id = 0, /* Bus number */
324 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
325 .resource = bfin_spi0_resource,
327 .platform_data = &bfin_spi0_info, /* Passed to driver */
332 static struct spi_board_info bfin_spi_board_info[] __initdata = {
333 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
334 || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
336 .modalias = "ad183x",
337 .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
340 .platform_data = "ad1836", /* only includes chip name for the moment */
344 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
346 .modalias = "spidev",
347 .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
354 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
355 #include <linux/input.h>
356 #include <linux/gpio_keys.h>
358 static struct gpio_keys_button bfin_gpio_keys_table[] = {
359 {BTN_0, GPIO_PF5, 1, "gpio-keys: BTN0"},
360 {BTN_1, GPIO_PF6, 1, "gpio-keys: BTN1"},
361 {BTN_2, GPIO_PF7, 1, "gpio-keys: BTN2"},
362 {BTN_3, GPIO_PF8, 1, "gpio-keys: BTN3"},
365 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
366 .buttons = bfin_gpio_keys_table,
367 .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
370 static struct platform_device bfin_device_gpiokeys = {
373 .platform_data = &bfin_gpio_keys_data,
378 #if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
379 #include <linux/i2c-gpio.h>
381 static struct i2c_gpio_platform_data i2c_gpio_data = {
384 .sda_is_open_drain = 0,
385 .scl_is_open_drain = 0,
389 static struct platform_device i2c_gpio_device = {
393 .platform_data = &i2c_gpio_data,
398 static const unsigned int cclk_vlev_datasheet[] =
400 VRPAIR(VLEV_085, 250000000),
401 VRPAIR(VLEV_090, 300000000),
402 VRPAIR(VLEV_095, 313000000),
403 VRPAIR(VLEV_100, 350000000),
404 VRPAIR(VLEV_105, 400000000),
405 VRPAIR(VLEV_110, 444000000),
406 VRPAIR(VLEV_115, 450000000),
407 VRPAIR(VLEV_120, 475000000),
408 VRPAIR(VLEV_125, 500000000),
409 VRPAIR(VLEV_130, 600000000),
412 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
413 .tuple_tab = cclk_vlev_datasheet,
414 .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
415 .vr_settling_time = 25 /* us */,
418 static struct platform_device bfin_dpmc = {
421 .platform_data = &bfin_dmpc_vreg_data,
425 #if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
426 || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
427 #include <linux/videodev2.h>
428 #include <media/blackfin/bfin_capture.h>
429 #include <media/blackfin/ppi.h>
431 static const unsigned short ppi_req[] = {
432 P_PPI0_D0, P_PPI0_D1, P_PPI0_D2, P_PPI0_D3,
433 P_PPI0_D4, P_PPI0_D5, P_PPI0_D6, P_PPI0_D7,
434 P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
438 static const struct ppi_info ppi_info = {
439 .type = PPI_TYPE_PPI,
441 .irq_err = IRQ_PPI1_ERROR,
442 .base = (void __iomem *)PPI0_CONTROL,
446 #if defined(CONFIG_VIDEO_ADV7183) \
447 || defined(CONFIG_VIDEO_ADV7183_MODULE)
448 #include <media/adv7183.h>
449 static struct v4l2_input adv7183_inputs[] = {
453 .type = V4L2_INPUT_TYPE_CAMERA,
455 .capabilities = V4L2_IN_CAP_STD,
460 .type = V4L2_INPUT_TYPE_CAMERA,
462 .capabilities = V4L2_IN_CAP_STD,
467 .type = V4L2_INPUT_TYPE_CAMERA,
469 .capabilities = V4L2_IN_CAP_STD,
473 static struct bcap_route adv7183_routes[] = {
475 .input = ADV7183_COMPOSITE4,
476 .output = ADV7183_8BIT_OUT,
479 .input = ADV7183_SVIDEO0,
480 .output = ADV7183_8BIT_OUT,
483 .input = ADV7183_COMPONENT0,
484 .output = ADV7183_8BIT_OUT,
489 static const unsigned adv7183_gpio[] = {
490 GPIO_PF13, /* reset pin */
491 GPIO_PF2, /* output enable pin */
494 static struct bfin_capture_config bfin_capture_data = {
495 .card_name = "BF561",
496 .inputs = adv7183_inputs,
497 .num_inputs = ARRAY_SIZE(adv7183_inputs),
498 .routes = adv7183_routes,
503 .platform_data = (void *)adv7183_gpio,
505 .ppi_info = &ppi_info,
506 .ppi_control = (PACK_EN | DLEN_8 | DMA32 | FLD_SEL),
510 static struct platform_device bfin_capture_device = {
511 .name = "bfin_capture",
513 .platform_data = &bfin_capture_data,
518 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
519 static struct platform_device bfin_i2s = {
521 .id = CONFIG_SND_BF5XX_SPORT_NUM,
522 /* TODO: add platform data here */
526 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
527 static struct platform_device bfin_tdm = {
529 .id = CONFIG_SND_BF5XX_SPORT_NUM,
530 /* TODO: add platform data here */
534 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
535 static struct platform_device bfin_ac97 = {
537 .id = CONFIG_SND_BF5XX_SPORT_NUM,
538 /* TODO: add platform data here */
542 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
543 || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
544 static const char * const ad1836_link[] = {
548 static struct platform_device bfin_ad1836_machine = {
549 .name = "bfin-snd-ad1836",
552 .platform_data = (void *)ad1836_link,
557 static struct platform_device *ezkit_devices[] __initdata = {
561 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
565 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
566 &net2272_bfin_device,
569 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
570 &bfin_isp1760_device,
573 #if defined(CONFIG_SPI_BFIN5XX) || defined(CONFIG_SPI_BFIN5XX_MODULE)
577 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
578 #ifdef CONFIG_SERIAL_BFIN_UART0
583 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
584 #ifdef CONFIG_BFIN_SIR0
589 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
590 &bfin_device_gpiokeys,
593 #if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
597 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
601 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
605 #if defined(CONFIG_VIDEO_BLACKFIN_CAPTURE) \
606 || defined(CONFIG_VIDEO_BLACKFIN_CAPTURE_MODULE)
607 &bfin_capture_device,
610 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
614 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
618 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
622 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) || \
623 defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
624 &bfin_ad1836_machine,
628 static int __init net2272_init(void)
630 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
633 ret = gpio_request(GPIO_PF11, "net2272");
637 /* Reset the USB chip */
638 gpio_direction_output(GPIO_PF11, 0);
640 gpio_set_value(GPIO_PF11, 1);
646 static int __init ezkit_init(void)
650 printk(KERN_INFO "%s(): registering device resources\n", __func__);
652 ret = platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
656 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
657 bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 12));
661 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
662 bfin_write_FIO0_DIR(bfin_read_FIO0_DIR() | (1 << 15));
663 bfin_write_FIO0_FLAG_S(1 << 15);
666 * This initialization lasts for approximately 4500 MCLKs.
673 pr_warning("unable to configure net2272; it probably won't work\n");
675 spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
679 arch_initcall(ezkit_init);
681 static struct platform_device *ezkit_early_devices[] __initdata = {
682 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
683 #ifdef CONFIG_SERIAL_BFIN_UART0
689 void __init native_machine_early_platform_add_devices(void)
691 printk(KERN_INFO "register early platform devices\n");
692 early_platform_add_devices(ezkit_early_devices,
693 ARRAY_SIZE(ezkit_early_devices));