board/freescale/ls1021atwr/ls1021atwr.c

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <i2c.h>
   9 #include <asm/io.h>
  10 #include <asm/arch/immap_ls102xa.h>
  11 #include <asm/arch/clock.h>
  12 #include <asm/arch/fsl_serdes.h>
  13 #include <mmc.h>
  14 #include <fsl_esdhc.h>
  15 #include <fsl_ifc.h>
  16 #include <netdev.h>
  17 #include <fsl_mdio.h>
  18 #include <tsec.h>
  19 #include <fsl_sec.h>
  20 #ifdef CONFIG_U_QE
  21 #include "../../../drivers/qe/qe.h"
  22 #endif
  23
  24
  25 DECLARE_GLOBAL_DATA_PTR;
  26
  27 #define VERSION_MASK            0x00FF
  28 #define BANK_MASK               0x0001
  29 #define CONFIG_RESET            0x1
  30 #define INIT_RESET              0x1
  31
  32 #define CPLD_SET_MUX_SERDES     0x20
  33 #define CPLD_SET_BOOT_BANK      0x40
  34
  35 #define BOOT_FROM_UPPER_BANK    0x0
  36 #define BOOT_FROM_LOWER_BANK    0x1
  37
  38 #define LANEB_SATA              (0x01)
  39 #define LANEB_SGMII1            (0x02)
  40 #define LANEC_SGMII1            (0x04)
  41 #define LANEC_PCIEX1            (0x08)
  42 #define LANED_PCIEX2            (0x10)
  43 #define LANED_SGMII2            (0x20)
  44
  45 #define MASK_LANE_B             0x1
  46 #define MASK_LANE_C             0x2
  47 #define MASK_LANE_D             0x4
  48 #define MASK_SGMII              0x8
  49
  50 #define KEEP_STATUS             0x0
  51 #define NEED_RESET              0x1
  52
  53 struct cpld_data {
  54         u8 cpld_ver;            /* cpld revision */
  55         u8 cpld_ver_sub;        /* cpld sub revision */
  56         u8 pcba_ver;            /* pcb revision number */
  57         u8 system_rst;          /* reset system by cpld */
  58         u8 soft_mux_on;         /* CPLD override physical switches Enable */
  59         u8 cfg_rcw_src1;        /* Reset config word 1 */
  60         u8 cfg_rcw_src2;        /* Reset config word 2 */
  61         u8 vbank;               /* Flash bank selection Control */
  62         u8 gpio;                /* GPIO for TWR-ELEV */
  63         u8 i2c3_ifc_mux;
  64         u8 mux_spi2;
  65         u8 can3_usb2_mux;       /* CAN3 and USB2 Selection */
  66         u8 qe_lcd_mux;          /* QE and LCD Selection */
  67         u8 serdes_mux;          /* Multiplexed pins for SerDes Lanes */
  68         u8 global_rst;          /* reset with init CPLD reg to default */
  69         u8 rev1;                /* Reserved */
  70         u8 rev2;                /* Reserved */
  71 };
  72
  73 static void convert_serdes_mux(int type, int need_reset);
  74
  75 void cpld_show(void)
  76 {
  77         struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
  78
  79         printf("CPLD:  V%x.%x\nPCBA:  V%x.0\nVBank: %d\n",
  80                in_8(&cpld_data->cpld_ver) & VERSION_MASK,
  81                in_8(&cpld_data->cpld_ver_sub) & VERSION_MASK,
  82                in_8(&cpld_data->pcba_ver) & VERSION_MASK,
  83                in_8(&cpld_data->vbank) & BANK_MASK);
  84
  85 #ifdef CONFIG_DEBUG
  86         printf("soft_mux_on =%x\n",
  87                in_8(&cpld_data->soft_mux_on));
  88         printf("cfg_rcw_src1 =%x\n",
  89                in_8(&cpld_data->cfg_rcw_src1));
  90         printf("cfg_rcw_src2 =%x\n",
  91                in_8(&cpld_data->cfg_rcw_src2));
  92         printf("vbank =%x\n",
  93                in_8(&cpld_data->vbank));
  94         printf("gpio =%x\n",
  95                in_8(&cpld_data->gpio));
  96         printf("i2c3_ifc_mux =%x\n",
  97                in_8(&cpld_data->i2c3_ifc_mux));
  98         printf("mux_spi2 =%x\n",
  99                in_8(&cpld_data->mux_spi2));
 100         printf("can3_usb2_mux =%x\n",
 101                in_8(&cpld_data->can3_usb2_mux));
 102         printf("qe_lcd_mux =%x\n",
 103                in_8(&cpld_data->qe_lcd_mux));
 104         printf("serdes_mux =%x\n",
 105                in_8(&cpld_data->serdes_mux));
 106 #endif
 107 }
 108
 109 int checkboard(void)
 110 {
 111         puts("Board: LS1021ATWR\n");
 112         cpld_show();
 113
 114         return 0;
 115 }
 116
 117 void ddrmc_init(void)
 118 {
 119         struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR;
 120
 121         out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG);
 122
 123         out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS);
 124         out_be32(&ddr->cs0_config, DDR_CS0_CONFIG);
 125
 126         out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0);
 127         out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1);
 128         out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2);
 129         out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3);
 130         out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4);
 131         out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5);
 132
 133         out_be32(&ddr->sdram_cfg_2,  DDR_SDRAM_CFG_2);
 134
 135         out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE);
 136         out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2);
 137
 138         out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL);
 139
 140         out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL);
 141
 142         out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2);
 143         out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3);
 144
 145         out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1);
 146         out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2);
 147
 148         out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL);
 149         out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL);
 150
 151         out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2);
 152         udelay(1);
 153         out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | DDR_SDRAM_CFG_MEM_EN);
 154 }
 155
 156 int dram_init(void)
 157 {
 158 #if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
 159         ddrmc_init();
 160 #endif
 161
 162         gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
 163         return 0;
 164 }
 165
 166 #ifdef CONFIG_FSL_ESDHC
 167 struct fsl_esdhc_cfg esdhc_cfg[1] = {
 168         {CONFIG_SYS_FSL_ESDHC_ADDR},
 169 };
 170
 171 int board_mmc_init(bd_t *bis)
 172 {
 173         esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 174
 175         return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
 176 }
 177 #endif
 178
 179 #ifdef CONFIG_TSEC_ENET
 180 int board_eth_init(bd_t *bis)
 181 {
 182         struct fsl_pq_mdio_info mdio_info;
 183         struct tsec_info_struct tsec_info[4];
 184         int num = 0;
 185
 186 #ifdef CONFIG_TSEC1
 187         SET_STD_TSEC_INFO(tsec_info[num], 1);
 188         if (is_serdes_configured(SGMII_TSEC1)) {
 189                 puts("eTSEC1 is in sgmii mode.\n");
 190                 tsec_info[num].flags |= TSEC_SGMII;
 191         }
 192         num++;
 193 #endif
 194 #ifdef CONFIG_TSEC2
 195         SET_STD_TSEC_INFO(tsec_info[num], 2);
 196         if (is_serdes_configured(SGMII_TSEC2)) {
 197                 puts("eTSEC2 is in sgmii mode.\n");
 198                 tsec_info[num].flags |= TSEC_SGMII;
 199         }
 200         num++;
 201 #endif
 202 #ifdef CONFIG_TSEC3
 203         SET_STD_TSEC_INFO(tsec_info[num], 3);
 204         num++;
 205 #endif
 206         if (!num) {
 207                 printf("No TSECs initialized\n");
 208                 return 0;
 209         }
 210
 211         mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
 212         mdio_info.name = DEFAULT_MII_NAME;
 213         fsl_pq_mdio_init(bis, &mdio_info);
 214
 215         tsec_eth_init(bis, tsec_info, num);
 216
 217         return pci_eth_init(bis);
 218 }
 219 #endif
 220
 221 int config_serdes_mux(void)
 222 {
 223         struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 224         u32 protocol = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK;
 225
 226         protocol >>= RCWSR4_SRDS1_PRTCL_SHIFT;
 227         switch (protocol) {
 228         case 0x10:
 229                 convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
 230                 convert_serdes_mux(LANED_PCIEX2 |
 231                                 LANEC_PCIEX1, KEEP_STATUS);
 232                 break;
 233         case 0x20:
 234                 convert_serdes_mux(LANEB_SGMII1, KEEP_STATUS);
 235                 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS);
 236                 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
 237                 break;
 238         case 0x30:
 239                 convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
 240                 convert_serdes_mux(LANEC_SGMII1, KEEP_STATUS);
 241                 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
 242                 break;
 243         case 0x70:
 244                 convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
 245                 convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS);
 246                 convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
 247                 break;
 248         }
 249
 250         return 0;
 251 }
 252
 253 int board_early_init_f(void)
 254 {
 255         struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
 256
 257 #ifdef CONFIG_TSEC_ENET
 258         out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
 259         out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
 260 #endif
 261
 262 #ifdef CONFIG_FSL_IFC
 263         init_early_memctl_regs();
 264 #endif
 265
 266 #ifdef CONFIG_FSL_DCU_FB
 267         out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN);
 268 #endif
 269
 270         return 0;
 271 }
 272
 273 int board_init(void)
 274 {
 275         struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
 276
 277         /*
 278          * Set CCI-400 Slave interface S0, S1, S2 Shareable Override Register
 279          * All transactions are treated as non-shareable
 280          */
 281         out_le32(&cci->slave[0].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
 282         out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
 283         out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
 284
 285 #ifndef CONFIG_SYS_FSL_NO_SERDES
 286         fsl_serdes_init();
 287         config_serdes_mux();
 288 #endif
 289
 290 #ifdef CONFIG_U_QE
 291         u_qe_init();
 292 #endif
 293
 294         return 0;
 295 }
 296
 297 #if defined(CONFIG_MISC_INIT_R)
 298 int misc_init_r(void)
 299 {
 300 #ifdef CONFIG_FSL_CAAM
 301         return sec_init();
 302 #endif
 303 }
 304 #endif
 305
 306 void ft_board_setup(void *blob, bd_t *bd)
 307 {
 308         ft_cpu_setup(blob, bd);
 309 }
 310
 311 u8 flash_read8(void *addr)
 312 {
 313         return __raw_readb(addr + 1);
 314 }
 315
 316 void flash_write16(u16 val, void *addr)
 317 {
 318         u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
 319
 320         __raw_writew(shftval, addr);
 321 }
 322
 323 u16 flash_read16(void *addr)
 324 {
 325         u16 val = __raw_readw(addr);
 326
 327         return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
 328 }
 329
 330 static void convert_flash_bank(char bank)
 331 {
 332         struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
 333
 334         printf("Now switch to boot from flash bank %d.\n", bank);
 335         cpld_data->soft_mux_on = CPLD_SET_BOOT_BANK;
 336         cpld_data->vbank = bank;
 337
 338         printf("Reset board to enable configuration.\n");
 339         cpld_data->system_rst = CONFIG_RESET;
 340 }
 341
 342 static int flash_bank_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
 343                           char * const argv[])
 344 {
 345         if (argc != 2)
 346                 return CMD_RET_USAGE;
 347         if (strcmp(argv[1], "0") == 0)
 348                 convert_flash_bank(BOOT_FROM_UPPER_BANK);
 349         else if (strcmp(argv[1], "1") == 0)
 350                 convert_flash_bank(BOOT_FROM_LOWER_BANK);
 351         else
 352                 return CMD_RET_USAGE;
 353
 354         return 0;
 355 }
 356
 357 U_BOOT_CMD(
 358         boot_bank, 2, 0, flash_bank_cmd,
 359         "Flash bank Selection Control",
 360         "bank[0-upper bank/1-lower bank] (e.g. boot_bank 0)"
 361 );
 362
 363 static int cpld_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
 364                           char * const argv[])
 365 {
 366         struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
 367
 368         if (argc > 2)
 369                 return CMD_RET_USAGE;
 370         if ((argc == 1) || (strcmp(argv[1], "conf") == 0))
 371                 cpld_data->system_rst = CONFIG_RESET;
 372         else if (strcmp(argv[1], "init") == 0)
 373                 cpld_data->global_rst = INIT_RESET;
 374         else
 375                 return CMD_RET_USAGE;
 376
 377         return 0;
 378 }
 379
 380 U_BOOT_CMD(
 381         cpld_reset, 2, 0, cpld_reset_cmd,
 382         "Reset via CPLD",
 383         "conf\n"
 384         "       -reset with current CPLD configuration\n"
 385         "init\n"
 386         "       -reset and initial CPLD configuration with default value"
 387
 388 );
 389
 390 static void convert_serdes_mux(int type, int need_reset)
 391 {
 392         char current_serdes;
 393         struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
 394
 395         current_serdes = cpld_data->serdes_mux;
 396
 397         switch (type) {
 398         case LANEB_SATA:
 399                 current_serdes &= ~MASK_LANE_B;
 400                 break;
 401         case LANEB_SGMII1:
 402                 current_serdes |= (MASK_LANE_B | MASK_SGMII | MASK_LANE_C);
 403                 break;
 404         case LANEC_SGMII1:
 405                 current_serdes &= ~(MASK_LANE_B | MASK_SGMII | MASK_LANE_C);
 406                 break;
 407         case LANED_SGMII2:
 408                 current_serdes |= MASK_LANE_D;
 409                 break;
 410         case LANEC_PCIEX1:
 411                 current_serdes |= MASK_LANE_C;
 412                 break;
 413         case (LANED_PCIEX2 | LANEC_PCIEX1):
 414                 current_serdes |= MASK_LANE_C;
 415                 current_serdes &= ~MASK_LANE_D;
 416                 break;
 417         default:
 418                 printf("CPLD serdes MUX: unsupported MUX type 0x%x\n", type);
 419                 return;
 420         }
 421
 422         cpld_data->soft_mux_on |= CPLD_SET_MUX_SERDES;
 423         cpld_data->serdes_mux = current_serdes;
 424
 425         if (need_reset == 1) {
 426                 printf("Reset board to enable configuration\n");
 427                 cpld_data->system_rst = CONFIG_RESET;
 428         }
 429 }
 430
 431 void print_serdes_mux(void)
 432 {
 433         char current_serdes;
 434         struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
 435
 436         current_serdes = cpld_data->serdes_mux;
 437
 438         printf("Serdes Lane B: ");
 439         if ((current_serdes & MASK_LANE_B) == 0)
 440                 printf("SATA,\n");
 441         else
 442                 printf("SGMII 1,\n");
 443
 444         printf("Serdes Lane C: ");
 445         if ((current_serdes & MASK_LANE_C) == 0)
 446                 printf("SGMII 1,\n");
 447         else
 448                 printf("PCIe,\n");
 449
 450         printf("Serdes Lane D: ");
 451         if ((current_serdes & MASK_LANE_D) == 0)
 452                 printf("PCIe,\n");
 453         else
 454                 printf("SGMII 2,\n");
 455
 456         printf("SGMII 1 is on lane ");
 457         if ((current_serdes & MASK_SGMII) == 0)
 458                 printf("C.\n");
 459         else
 460                 printf("B.\n");
 461 }
 462
 463 static int serdes_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
 464                           char * const argv[])
 465 {
 466         if (argc != 2)
 467                 return CMD_RET_USAGE;
 468         if (strcmp(argv[1], "sata") == 0) {
 469                 printf("Set serdes lane B to SATA.\n");
 470                 convert_serdes_mux(LANEB_SATA, NEED_RESET);
 471         } else if (strcmp(argv[1], "sgmii1b") == 0) {
 472                 printf("Set serdes lane B to SGMII 1.\n");
 473                 convert_serdes_mux(LANEB_SGMII1, NEED_RESET);
 474         } else if (strcmp(argv[1], "sgmii1c") == 0) {
 475                 printf("Set serdes lane C to SGMII 1.\n");
 476                 convert_serdes_mux(LANEC_SGMII1, NEED_RESET);
 477         } else if (strcmp(argv[1], "sgmii2") == 0) {
 478                 printf("Set serdes lane D to SGMII 2.\n");
 479                 convert_serdes_mux(LANED_SGMII2, NEED_RESET);
 480         } else if (strcmp(argv[1], "pciex1") == 0) {
 481                 printf("Set serdes lane C to PCIe X1.\n");
 482                 convert_serdes_mux(LANEC_PCIEX1, NEED_RESET);
 483         } else if (strcmp(argv[1], "pciex2") == 0) {
 484                 printf("Set serdes lane C & lane D to PCIe X2.\n");
 485                 convert_serdes_mux((LANED_PCIEX2 | LANEC_PCIEX1), NEED_RESET);
 486         } else if (strcmp(argv[1], "show") == 0) {
 487                 print_serdes_mux();
 488         } else {
 489                 return CMD_RET_USAGE;
 490         }
 491
 492         return 0;
 493 }
 494
 495 U_BOOT_CMD(
 496         lane_bank, 2, 0, serdes_mux_cmd,
 497         "Multiplexed function setting for SerDes Lanes",
 498         "sata\n"
 499         "       -change lane B to sata\n"
 500         "lane_bank sgmii1b\n"
 501         "       -change lane B to SGMII1\n"
 502         "lane_bank sgmii1c\n"
 503         "       -change lane C to SGMII1\n"
 504         "lane_bank sgmii2\n"
 505         "       -change lane D to SGMII2\n"
 506         "lane_bank pciex1\n"
 507         "       -change lane C to PCIeX1\n"
 508         "lane_bank pciex2\n"
 509         "       -change lane C & lane D to PCIeX2\n"
 510         "\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n"
 511 );