2 # Touchscreen driver configuration
4 menuconfig INPUT_TOUCHSCREEN
7 Say Y here, and a list of supported touchscreens will be displayed.
8 This option doesn't affect the kernel.
14 config TOUCHSCREEN_88PM860X
15 tristate "Marvell 88PM860x touchscreen"
16 depends on MFD_88PM860X
18 Say Y here if you have a 88PM860x PMIC and want to enable
19 support for the built-in touchscreen.
23 To compile this driver as a module, choose M here: the
24 module will be called 88pm860x-ts.
26 config TOUCHSCREEN_ADS7846
27 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
29 depends on HWMON = n || HWMON
31 Say Y here if you have a touchscreen interface using the
32 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
33 and your board-specific setup code includes that in its
36 If HWMON is selected, and the driver is told the reference voltage
37 on your board, you will also get hwmon interfaces for the voltage
38 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
40 If unsure, say N (but it's safe to say "Y").
42 To compile this driver as a module, choose M here: the
43 module will be called ads7846.
45 config TOUCHSCREEN_AD7877
46 tristate "AD7877 based touchscreens"
49 Say Y here if you have a touchscreen interface using the
50 AD7877 controller, and your board-specific initialization
51 code includes that in its table of SPI devices.
53 If unsure, say N (but it's safe to say "Y").
55 To compile this driver as a module, choose M here: the
56 module will be called ad7877.
58 config TOUCHSCREEN_AD7879
59 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
61 Say Y here if you want to support a touchscreen interface using
62 the AD7879-1/AD7889-1 controller.
64 You should select a bus connection too.
66 To compile this driver as a module, choose M here: the
67 module will be called ad7879.
69 config TOUCHSCREEN_AD7879_I2C
70 tristate "support I2C bus connection"
71 depends on TOUCHSCREEN_AD7879 && I2C
73 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
75 To compile this driver as a module, choose M here: the
76 module will be called ad7879-i2c.
78 config TOUCHSCREEN_AD7879_SPI
79 tristate "support SPI bus connection"
80 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
82 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
84 If unsure, say N (but it's safe to say "Y").
86 To compile this driver as a module, choose M here: the
87 module will be called ad7879-spi.
89 config TOUCHSCREEN_BITSY
90 tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
91 depends on SA1100_BITSY
94 Say Y here if you have the h3600 (Bitsy) touchscreen.
98 To compile this driver as a module, choose M here: the
99 module will be called h3600_ts_input.
101 config TOUCHSCREEN_CY8CTMG110
102 tristate "cy8ctmg110 touchscreen"
107 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
112 To compile this driver as a module, choose M here: the
113 module will be called cy8ctmg110_ts.
115 config TOUCHSCREEN_DA9034
116 tristate "Touchscreen support for Dialog Semiconductor DA9034"
117 depends on PMIC_DA903X
120 Say Y here to enable the support for the touchscreen found
121 on Dialog Semiconductor DA9034 PMIC.
123 config TOUCHSCREEN_DYNAPRO
124 tristate "Dynapro serial touchscreen"
127 Say Y here if you have a Dynapro serial touchscreen connected to
132 To compile this driver as a module, choose M here: the
133 module will be called dynapro.
135 config TOUCHSCREEN_HAMPSHIRE
136 tristate "Hampshire serial touchscreen"
139 Say Y here if you have a Hampshire serial touchscreen connected to
144 To compile this driver as a module, choose M here: the
145 module will be called hampshire.
147 config TOUCHSCREEN_EETI
148 tristate "EETI touchscreen panel support"
151 Say Y here to enable support for I2C connected EETI touch panels.
153 To compile this driver as a module, choose M here: the
154 module will be called eeti_ts.
156 config TOUCHSCREEN_FUJITSU
157 tristate "Fujitsu serial touchscreen"
160 Say Y here if you have the Fujitsu touchscreen (such as one
161 installed in Lifebook P series laptop) connected to your
166 To compile this driver as a module, choose M here: the
167 module will be called fujitsu-ts.
169 config TOUCHSCREEN_S3C2410
170 tristate "Samsung S3C2410/generic touchscreen input driver"
171 depends on ARCH_S3C2410 || SAMSUNG_DEV_TS
174 Say Y here if you have the s3c2410 touchscreen.
178 To compile this driver as a module, choose M here: the
179 module will be called s3c2410_ts.
181 config TOUCHSCREEN_GUNZE
182 tristate "Gunze AHL-51S touchscreen"
185 Say Y here if you have the Gunze AHL-51 touchscreen connected to
190 To compile this driver as a module, choose M here: the
191 module will be called gunze.
193 config TOUCHSCREEN_ELO
194 tristate "Elo serial touchscreens"
197 Say Y here if you have an Elo serial touchscreen connected to
202 To compile this driver as a module, choose M here: the
203 module will be called elo.
205 config TOUCHSCREEN_WACOM_W8001
206 tristate "Wacom W8001 penabled serial touchscreen"
209 Say Y here if you have an Wacom W8001 penabled serial touchscreen
210 connected to your system.
214 To compile this driver as a module, choose M here: the
215 module will be called wacom_w8001.
217 config TOUCHSCREEN_MCS5000
218 tristate "MELFAS MCS-5000 touchscreen"
221 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
226 To compile this driver as a module, choose M here: the
227 module will be called mcs5000_ts.
229 config TOUCHSCREEN_MTOUCH
230 tristate "MicroTouch serial touchscreens"
233 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
238 To compile this driver as a module, choose M here: the
239 module will be called mtouch.
241 config TOUCHSCREEN_INEXIO
242 tristate "iNexio serial touchscreens"
245 Say Y here if you have an iNexio serial touchscreen connected to
250 To compile this driver as a module, choose M here: the
251 module will be called inexio.
253 config TOUCHSCREEN_MK712
254 tristate "ICS MicroClock MK712 touchscreen"
256 Say Y here if you have the ICS MicroClock MK712 touchscreen
257 controller chip in your system.
261 To compile this driver as a module, choose M here: the
262 module will be called mk712.
264 config TOUCHSCREEN_HP600
265 tristate "HP Jornada 6xx touchscreen"
266 depends on SH_HP6XX && SH_ADC
268 Say Y here if you have a HP Jornada 620/660/680/690 and want to
269 support the built-in touchscreen.
271 To compile this driver as a module, choose M here: the
272 module will be called hp680_ts_input.
274 config TOUCHSCREEN_HP7XX
275 tristate "HP Jornada 7xx touchscreen"
276 depends on SA1100_JORNADA720_SSP
278 Say Y here if you have a HP Jornada 710/720/728 and want
279 to support the built-in touchscreen.
281 To compile this driver as a module, choose M here: the
282 module will be called jornada720_ts.
284 config TOUCHSCREEN_HTCPEN
285 tristate "HTC Shift X9500 touchscreen"
288 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
289 Clio / Shangrila and want to support the built-in touchscreen.
293 To compile this driver as a module, choose M here: the
294 module will be called htcpen.
296 config TOUCHSCREEN_PENMOUNT
297 tristate "Penmount serial touchscreen"
300 Say Y here if you have a Penmount serial touchscreen connected to
305 To compile this driver as a module, choose M here: the
306 module will be called penmount.
308 config TOUCHSCREEN_QT602240
309 tristate "QT602240 I2C Touchscreen"
312 Say Y here if you have the AT42QT602240/ATMXT224 I2C touchscreen
313 connected to your system.
317 To compile this driver as a module, choose M here: the
318 module will be called qt602240_ts.
320 config TOUCHSCREEN_MIGOR
321 tristate "Renesas MIGO-R touchscreen"
322 depends on SH_MIGOR && I2C
324 Say Y here to enable MIGO-R touchscreen support.
328 To compile this driver as a module, choose M here: the
329 module will be called migor_ts.
331 config TOUCHSCREEN_TOUCHRIGHT
332 tristate "Touchright serial touchscreen"
335 Say Y here if you have a Touchright serial touchscreen connected to
340 To compile this driver as a module, choose M here: the
341 module will be called touchright.
343 config TOUCHSCREEN_TOUCHWIN
344 tristate "Touchwin serial touchscreen"
347 Say Y here if you have a Touchwin serial touchscreen connected to
352 To compile this driver as a module, choose M here: the
353 module will be called touchwin.
355 config TOUCHSCREEN_ATMEL_TSADCC
356 tristate "Atmel Touchscreen Interface"
357 depends on ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
359 Say Y here if you have a 4-wire touchscreen connected to the
360 ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
364 To compile this driver as a module, choose M here: the
365 module will be called atmel_tsadcc.
367 config TOUCHSCREEN_UCB1400
368 tristate "Philips UCB1400 touchscreen"
370 depends on UCB1400_CORE
372 This enables support for the Philips UCB1400 touchscreen interface.
373 The UCB1400 is an AC97 audio codec. The touchscreen interface
374 will be initialized only after the ALSA subsystem has been
375 brought up and the UCB1400 detected. You therefore have to
376 configure ALSA support as well (either built-in or modular,
377 independently of whether this driver is itself built-in or
378 modular) for this driver to work.
380 To compile this driver as a module, choose M here: the
381 module will be called ucb1400_ts.
383 config TOUCHSCREEN_WM97XX
384 tristate "Support for WM97xx AC97 touchscreen controllers"
387 Say Y here if you have a Wolfson Microelectronics WM97xx
388 touchscreen connected to your system. Note that this option
389 only enables core driver, you will also need to select
390 support for appropriate chip below.
394 To compile this driver as a module, choose M here: the
395 module will be called wm97xx-ts.
397 config TOUCHSCREEN_WM9705
398 bool "WM9705 Touchscreen interface support"
399 depends on TOUCHSCREEN_WM97XX
402 Say Y here to enable support for the Wolfson Microelectronics
403 WM9705 touchscreen controller.
405 config TOUCHSCREEN_WM9712
406 bool "WM9712 Touchscreen interface support"
407 depends on TOUCHSCREEN_WM97XX
410 Say Y here to enable support for the Wolfson Microelectronics
411 WM9712 touchscreen controller.
413 config TOUCHSCREEN_WM9713
414 bool "WM9713 Touchscreen interface support"
415 depends on TOUCHSCREEN_WM97XX
418 Say Y here to enable support for the Wolfson Microelectronics
419 WM9713 touchscreen controller.
421 config TOUCHSCREEN_WM97XX_ATMEL
422 tristate "WM97xx Atmel accelerated touch"
423 depends on TOUCHSCREEN_WM97XX && (AVR32 || ARCH_AT91)
425 Say Y here for support for streaming mode with WM97xx touchscreens
426 on Atmel AT91 or AVR32 systems with an AC97C module.
428 Be aware that this will use channel B in the controller for
429 streaming data, this must not conflict with other AC97C drivers.
433 To compile this driver as a module, choose M here: the module will
434 be called atmel-wm97xx.
436 config TOUCHSCREEN_WM97XX_MAINSTONE
437 tristate "WM97xx Mainstone/Palm accelerated touch"
438 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
440 Say Y here for support for streaming mode with WM97xx touchscreens
441 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
445 To compile this driver as a module, choose M here: the
446 module will be called mainstone-wm97xx.
448 config TOUCHSCREEN_WM97XX_ZYLONITE
449 tristate "Zylonite accelerated touch"
450 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
451 select TOUCHSCREEN_WM9713
453 Say Y here for support for streaming mode with the touchscreen
458 To compile this driver as a module, choose M here: the
459 module will be called zylonite-wm97xx.
461 config TOUCHSCREEN_USB_COMPOSITE
462 tristate "USB Touchscreen Driver"
463 depends on USB_ARCH_HAS_HCD
466 USB Touchscreen driver for:
467 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
468 - PanJit TouchSet USB
469 - 3M MicroTouch USB (EX II series)
471 - some other eTurboTouch
474 - IRTOUCHSYSTEMS/UNITOP
476 - GoTop Super_Q2/GogoPen/PenPower tablets
477 - JASTEC USB Touch Controller/DigiTech DTR-02U
478 - Zytronic controllers
480 Have a look at <http://linux.chapter7.ch/touchkit/> for
481 a usage description and the required user-space stuff.
483 To compile this driver as a module, choose M here: the
484 module will be called usbtouchscreen.
486 config TOUCHSCREEN_MC13783
487 tristate "Freescale MC13783 touchscreen input driver"
488 depends on MFD_MC13783
490 Say Y here if you have an Freescale MC13783 PMIC on your
491 board and want to use its touchscreen
495 To compile this driver as a module, choose M here: the
496 module will be called mc13783_ts.
498 config TOUCHSCREEN_USB_EGALAX
500 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
501 depends on TOUCHSCREEN_USB_COMPOSITE
503 config TOUCHSCREEN_USB_PANJIT
505 bool "PanJit device support" if EMBEDDED
506 depends on TOUCHSCREEN_USB_COMPOSITE
508 config TOUCHSCREEN_USB_3M
510 bool "3M/Microtouch EX II series device support" if EMBEDDED
511 depends on TOUCHSCREEN_USB_COMPOSITE
513 config TOUCHSCREEN_USB_ITM
515 bool "ITM device support" if EMBEDDED
516 depends on TOUCHSCREEN_USB_COMPOSITE
518 config TOUCHSCREEN_USB_ETURBO
520 bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
521 depends on TOUCHSCREEN_USB_COMPOSITE
523 config TOUCHSCREEN_USB_GUNZE
525 bool "Gunze AHL61 device support" if EMBEDDED
526 depends on TOUCHSCREEN_USB_COMPOSITE
528 config TOUCHSCREEN_USB_DMC_TSC10
530 bool "DMC TSC-10/25 device support" if EMBEDDED
531 depends on TOUCHSCREEN_USB_COMPOSITE
533 config TOUCHSCREEN_USB_IRTOUCH
535 bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
536 depends on TOUCHSCREEN_USB_COMPOSITE
538 config TOUCHSCREEN_USB_IDEALTEK
540 bool "IdealTEK URTC1000 device support" if EMBEDDED
541 depends on TOUCHSCREEN_USB_COMPOSITE
543 config TOUCHSCREEN_USB_GENERAL_TOUCH
545 bool "GeneralTouch Touchscreen device support" if EMBEDDED
546 depends on TOUCHSCREEN_USB_COMPOSITE
548 config TOUCHSCREEN_USB_GOTOP
550 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
551 depends on TOUCHSCREEN_USB_COMPOSITE
553 config TOUCHSCREEN_USB_JASTEC
555 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EMBEDDED
556 depends on TOUCHSCREEN_USB_COMPOSITE
558 config TOUCHSCREEN_USB_E2I
560 bool "e2i Touchscreen controller (e.g. from Mimo 740)"
561 depends on TOUCHSCREEN_USB_COMPOSITE
563 config TOUCHSCREEN_USB_ZYTRONIC
565 bool "Zytronic controller" if EMBEDDED
566 depends on TOUCHSCREEN_USB_COMPOSITE
568 config TOUCHSCREEN_USB_ETT_TC45USB
570 bool "ET&T USB series TC4UM/TC5UH touchscreen controler support" if EMBEDDED
571 depends on TOUCHSCREEN_USB_COMPOSITE
573 config TOUCHSCREEN_USB_NEXIO
575 bool "NEXIO/iNexio device support" if EMBEDDED
576 depends on TOUCHSCREEN_USB_COMPOSITE
578 config TOUCHSCREEN_TOUCHIT213
579 tristate "Sahara TouchIT-213 touchscreen"
582 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
586 To compile this driver as a module, choose M here: the
587 module will be called touchit213.
589 config TOUCHSCREEN_TSC2007
590 tristate "TSC2007 based touchscreens"
593 Say Y here if you have a TSC2007 based touchscreen.
597 To compile this driver as a module, choose M here: the
598 module will be called tsc2007.
600 config TOUCHSCREEN_W90X900
601 tristate "W90P910 touchscreen driver"
604 Say Y here if you have a W90P910 based touchscreen.
606 To compile this driver as a module, choose M here: the
607 module will be called w90p910_ts.
609 config TOUCHSCREEN_PCAP
610 tristate "Motorola PCAP touchscreen"
613 Say Y here if you have a Motorola EZX telephone and
614 want to enable support for the built-in touchscreen.
616 To compile this driver as a module, choose M here: the
617 module will be called pcap_ts.
619 config TOUCHSCREEN_TPS6507X
620 tristate "TPS6507x based touchscreens"
623 Say Y here if you have a TPS6507x based touchscreen
628 To compile this driver as a module, choose M here: the
629 module will be called tps6507x_ts.