1 /*******************************************************************************
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2009 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
27 *******************************************************************************/
30 * 80003ES2LAN Gigabit Ethernet Controller (Copper)
31 * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
36 #define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00
37 #define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02
38 #define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10
39 #define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F
41 #define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008
42 #define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800
43 #define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010
45 #define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
46 #define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000
47 #define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000
49 #define E1000_KMRNCTRLSTA_OPMODE_MASK 0x000C
50 #define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO 0x0004
52 #define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
53 #define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000
55 #define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8
56 #define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9
58 /* GG82563 PHY Specific Status Register (Page 0, Register 16 */
59 #define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disab. */
60 #define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
61 #define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */
62 #define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */
63 #define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */
65 /* PHY Specific Control Register 2 (Page 0, Register 26) */
66 #define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000
67 /* 1=Reverse Auto-Negotiation */
69 /* MAC Specific Control Register (Page 2, Register 21) */
70 /* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
71 #define GG82563_MSCR_TX_CLK_MASK 0x0007
72 #define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004
73 #define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005
74 #define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007
76 #define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
78 /* DSP Distance Register (Page 5, Register 26) */
79 #define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M
85 /* Kumeran Mode Control Register (Page 193, Register 16) */
86 #define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
88 /* Max number of times Kumeran read/write should be validated */
89 #define GG82563_MAX_KMRN_RETRY 0x5
91 /* Power Management Control Register (Page 193, Register 20) */
92 #define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001
93 /* 1=Enable SERDES Electrical Idle */
95 /* In-Band Control Register (Page 194, Register 18) */
96 #define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
99 * A table for the GG82563 cable length where the range is defined
100 * with a lower bound at "index" and the upper bound at
103 static const u16 e1000_gg82563_cable_length_table[] =
104 { 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF };
105 #define GG82563_CABLE_LENGTH_TABLE_SIZE \
106 ARRAY_SIZE(e1000_gg82563_cable_length_table)
108 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw);
109 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
110 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
111 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
112 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
113 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
114 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
115 static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw);
116 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
118 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
120 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);
123 * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
124 * @hw: pointer to the HW structure
126 static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
128 struct e1000_phy_info *phy = &hw->phy;
131 if (hw->phy.media_type != e1000_media_type_copper) {
132 phy->type = e1000_phy_none;
135 phy->ops.power_up = e1000_power_up_phy_copper;
136 phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan;
140 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
141 phy->reset_delay_us = 100;
142 phy->type = e1000_phy_gg82563;
144 /* This can only be done after all function pointers are setup. */
145 ret_val = e1000e_get_phy_id(hw);
148 if (phy->id != GG82563_E_PHY_ID)
149 return -E1000_ERR_PHY;
155 * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
156 * @hw: pointer to the HW structure
158 static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
160 struct e1000_nvm_info *nvm = &hw->nvm;
161 u32 eecd = er32(EECD);
164 nvm->opcode_bits = 8;
166 switch (nvm->override) {
167 case e1000_nvm_override_spi_large:
169 nvm->address_bits = 16;
171 case e1000_nvm_override_spi_small:
173 nvm->address_bits = 8;
176 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
177 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
181 nvm->type = e1000_nvm_eeprom_spi;
183 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
184 E1000_EECD_SIZE_EX_SHIFT);
187 * Added to a constant, "size" becomes the left-shift value
188 * for setting word_size.
190 size += NVM_WORD_SIZE_BASE_SHIFT;
192 /* EEPROM access above 16k is unsupported */
195 nvm->word_size = 1 << size;
201 * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
202 * @hw: pointer to the HW structure
204 static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
206 struct e1000_hw *hw = &adapter->hw;
207 struct e1000_mac_info *mac = &hw->mac;
208 struct e1000_mac_operations *func = &mac->ops;
211 switch (adapter->pdev->device) {
212 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
213 hw->phy.media_type = e1000_media_type_internal_serdes;
216 hw->phy.media_type = e1000_media_type_copper;
220 /* Set mta register count */
221 mac->mta_reg_count = 128;
222 /* Set rar entry count */
223 mac->rar_entry_count = E1000_RAR_ENTRIES;
224 /* Set if manageability features are enabled. */
225 mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK)
227 /* Adaptive IFS not supported */
228 mac->adaptive_ifs = false;
231 switch (hw->phy.media_type) {
232 case e1000_media_type_copper:
233 func->setup_physical_interface = e1000_setup_copper_link_80003es2lan;
234 func->check_for_link = e1000e_check_for_copper_link;
236 case e1000_media_type_fiber:
237 func->setup_physical_interface = e1000e_setup_fiber_serdes_link;
238 func->check_for_link = e1000e_check_for_fiber_link;
240 case e1000_media_type_internal_serdes:
241 func->setup_physical_interface = e1000e_setup_fiber_serdes_link;
242 func->check_for_link = e1000e_check_for_serdes_link;
245 return -E1000_ERR_CONFIG;
249 /* set lan id for port to determine which phy lock to use */
250 hw->mac.ops.set_lan_id(hw);
255 static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
257 struct e1000_hw *hw = &adapter->hw;
260 rc = e1000_init_mac_params_80003es2lan(adapter);
264 rc = e1000_init_nvm_params_80003es2lan(hw);
268 rc = e1000_init_phy_params_80003es2lan(hw);
276 * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY
277 * @hw: pointer to the HW structure
279 * A wrapper to acquire access rights to the correct PHY.
281 static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
285 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
286 return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
290 * e1000_release_phy_80003es2lan - Release rights to access PHY
291 * @hw: pointer to the HW structure
293 * A wrapper to release access rights to the correct PHY.
295 static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
299 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
300 e1000_release_swfw_sync_80003es2lan(hw, mask);
304 * e1000_acquire_mac_csr_80003es2lan - Acquire rights to access Kumeran register
305 * @hw: pointer to the HW structure
307 * Acquire the semaphore to access the Kumeran interface.
310 static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw)
314 mask = E1000_SWFW_CSR_SM;
316 return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
320 * e1000_release_mac_csr_80003es2lan - Release rights to access Kumeran Register
321 * @hw: pointer to the HW structure
323 * Release the semaphore used to access the Kumeran interface
325 static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw)
329 mask = E1000_SWFW_CSR_SM;
331 e1000_release_swfw_sync_80003es2lan(hw, mask);
335 * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM
336 * @hw: pointer to the HW structure
338 * Acquire the semaphore to access the EEPROM.
340 static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw)
344 ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
348 ret_val = e1000e_acquire_nvm(hw);
351 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
357 * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM
358 * @hw: pointer to the HW structure
360 * Release the semaphore used to access the EEPROM.
362 static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw)
364 e1000e_release_nvm(hw);
365 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
369 * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
370 * @hw: pointer to the HW structure
371 * @mask: specifies which semaphore to acquire
373 * Acquire the SW/FW semaphore to access the PHY or NVM. The mask
374 * will also specify which port we're acquiring the lock for.
376 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
380 u32 fwmask = mask << 16;
384 while (i < timeout) {
385 if (e1000e_get_hw_semaphore(hw))
386 return -E1000_ERR_SWFW_SYNC;
388 swfw_sync = er32(SW_FW_SYNC);
389 if (!(swfw_sync & (fwmask | swmask)))
393 * Firmware currently using resource (fwmask)
394 * or other software thread using resource (swmask)
396 e1000e_put_hw_semaphore(hw);
402 e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
403 return -E1000_ERR_SWFW_SYNC;
407 ew32(SW_FW_SYNC, swfw_sync);
409 e1000e_put_hw_semaphore(hw);
415 * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore
416 * @hw: pointer to the HW structure
417 * @mask: specifies which semaphore to acquire
419 * Release the SW/FW semaphore used to access the PHY or NVM. The mask
420 * will also specify which port we're releasing the lock for.
422 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
426 while (e1000e_get_hw_semaphore(hw) != 0);
429 swfw_sync = er32(SW_FW_SYNC);
431 ew32(SW_FW_SYNC, swfw_sync);
433 e1000e_put_hw_semaphore(hw);
437 * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
438 * @hw: pointer to the HW structure
439 * @offset: offset of the register to read
440 * @data: pointer to the data returned from the operation
442 * Read the GG82563 PHY register.
444 static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
445 u32 offset, u16 *data)
451 ret_val = e1000_acquire_phy_80003es2lan(hw);
455 /* Select Configuration Page */
456 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
457 page_select = GG82563_PHY_PAGE_SELECT;
460 * Use Alternative Page Select register to access
461 * registers 30 and 31
463 page_select = GG82563_PHY_PAGE_SELECT_ALT;
466 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
467 ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
469 e1000_release_phy_80003es2lan(hw);
473 if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) {
475 * The "ready" bit in the MDIC register may be incorrectly set
476 * before the device has completed the "Page Select" MDI
477 * transaction. So we wait 200us after each MDI command...
481 /* ...and verify the command was successful. */
482 ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
484 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
485 ret_val = -E1000_ERR_PHY;
486 e1000_release_phy_80003es2lan(hw);
492 ret_val = e1000e_read_phy_reg_mdic(hw,
493 MAX_PHY_REG_ADDRESS & offset,
498 ret_val = e1000e_read_phy_reg_mdic(hw,
499 MAX_PHY_REG_ADDRESS & offset,
503 e1000_release_phy_80003es2lan(hw);
509 * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
510 * @hw: pointer to the HW structure
511 * @offset: offset of the register to read
512 * @data: value to write to the register
514 * Write to the GG82563 PHY register.
516 static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
517 u32 offset, u16 data)
523 ret_val = e1000_acquire_phy_80003es2lan(hw);
527 /* Select Configuration Page */
528 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
529 page_select = GG82563_PHY_PAGE_SELECT;
532 * Use Alternative Page Select register to access
533 * registers 30 and 31
535 page_select = GG82563_PHY_PAGE_SELECT_ALT;
538 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
539 ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
541 e1000_release_phy_80003es2lan(hw);
545 if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) {
547 * The "ready" bit in the MDIC register may be incorrectly set
548 * before the device has completed the "Page Select" MDI
549 * transaction. So we wait 200us after each MDI command...
553 /* ...and verify the command was successful. */
554 ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
556 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
557 e1000_release_phy_80003es2lan(hw);
558 return -E1000_ERR_PHY;
563 ret_val = e1000e_write_phy_reg_mdic(hw,
564 MAX_PHY_REG_ADDRESS & offset,
569 ret_val = e1000e_write_phy_reg_mdic(hw,
570 MAX_PHY_REG_ADDRESS & offset,
574 e1000_release_phy_80003es2lan(hw);
580 * e1000_write_nvm_80003es2lan - Write to ESB2 NVM
581 * @hw: pointer to the HW structure
582 * @offset: offset of the register to read
583 * @words: number of words to write
584 * @data: buffer of data to write to the NVM
586 * Write "words" of data to the ESB2 NVM.
588 static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
589 u16 words, u16 *data)
591 return e1000e_write_nvm_spi(hw, offset, words, data);
595 * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete
596 * @hw: pointer to the HW structure
598 * Wait a specific amount of time for manageability processes to complete.
599 * This is a function pointer entry point called by the phy module.
601 static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw)
603 s32 timeout = PHY_CFG_TIMEOUT;
604 u32 mask = E1000_NVM_CFG_DONE_PORT_0;
606 if (hw->bus.func == 1)
607 mask = E1000_NVM_CFG_DONE_PORT_1;
610 if (er32(EEMNGCTL) & mask)
616 e_dbg("MNG configuration cycle has not completed.\n");
617 return -E1000_ERR_RESET;
624 * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
625 * @hw: pointer to the HW structure
627 * Force the speed and duplex settings onto the PHY. This is a
628 * function pointer entry point called by the phy module.
630 static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
637 * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
638 * forced whenever speed and duplex are forced.
640 ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
644 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
645 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
649 e_dbg("GG82563 PSCR: %X\n", phy_data);
651 ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
655 e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
657 /* Reset the phy to commit changes. */
658 phy_data |= MII_CR_RESET;
660 ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
666 if (hw->phy.autoneg_wait_to_complete) {
667 e_dbg("Waiting for forced speed/duplex link "
668 "on GG82563 phy.\n");
670 ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
677 * We didn't get link.
678 * Reset the DSP and cross our fingers.
680 ret_val = e1000e_phy_reset_dsp(hw);
686 ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
692 ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
697 * Resetting the phy means we need to verify the TX_CLK corresponds
698 * to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
700 phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
701 if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
702 phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
704 phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
707 * In addition, we must re-enable CRS on Tx for both half and full
710 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
711 ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
717 * e1000_get_cable_length_80003es2lan - Set approximate cable length
718 * @hw: pointer to the HW structure
720 * Find the approximate cable length as measured by the GG82563 PHY.
721 * This is a function pointer entry point called by the phy module.
723 static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
725 struct e1000_phy_info *phy = &hw->phy;
729 ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
733 index = phy_data & GG82563_DSPD_CABLE_LENGTH;
735 if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5) {
736 ret_val = -E1000_ERR_PHY;
740 phy->min_cable_length = e1000_gg82563_cable_length_table[index];
741 phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5];
743 phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
750 * e1000_get_link_up_info_80003es2lan - Report speed and duplex
751 * @hw: pointer to the HW structure
752 * @speed: pointer to speed buffer
753 * @duplex: pointer to duplex buffer
755 * Retrieve the current speed and duplex configuration.
757 static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
762 if (hw->phy.media_type == e1000_media_type_copper) {
763 ret_val = e1000e_get_speed_and_duplex_copper(hw,
766 hw->phy.ops.cfg_on_link_up(hw);
768 ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
777 * e1000_reset_hw_80003es2lan - Reset the ESB2 controller
778 * @hw: pointer to the HW structure
780 * Perform a global reset to the ESB2 controller.
782 static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
788 * Prevent the PCI-E bus from sticking if there is no TLP connection
789 * on the last TLP read/write transaction when MAC is reset.
791 ret_val = e1000e_disable_pcie_master(hw);
793 e_dbg("PCI-E Master disable polling has failed.\n");
795 e_dbg("Masking off all interrupts\n");
796 ew32(IMC, 0xffffffff);
799 ew32(TCTL, E1000_TCTL_PSP);
806 ret_val = e1000_acquire_phy_80003es2lan(hw);
807 e_dbg("Issuing a global reset to MAC\n");
808 ew32(CTRL, ctrl | E1000_CTRL_RST);
809 e1000_release_phy_80003es2lan(hw);
811 ret_val = e1000e_get_auto_rd_done(hw);
813 /* We don't want to continue accessing MAC registers. */
816 /* Clear any pending interrupt events. */
817 ew32(IMC, 0xffffffff);
820 ret_val = e1000_check_alt_mac_addr_generic(hw);
826 * e1000_init_hw_80003es2lan - Initialize the ESB2 controller
827 * @hw: pointer to the HW structure
829 * Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
831 static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
833 struct e1000_mac_info *mac = &hw->mac;
838 e1000_initialize_hw_bits_80003es2lan(hw);
840 /* Initialize identification LED */
841 ret_val = e1000e_id_led_init(hw);
843 e_dbg("Error initializing identification LED\n");
844 /* This is not fatal and we should not stop init due to this */
846 /* Disabling VLAN filtering */
847 e_dbg("Initializing the IEEE VLAN\n");
848 mac->ops.clear_vfta(hw);
850 /* Setup the receive address. */
851 e1000e_init_rx_addrs(hw, mac->rar_entry_count);
853 /* Zero out the Multicast HASH table */
854 e_dbg("Zeroing the MTA\n");
855 for (i = 0; i < mac->mta_reg_count; i++)
856 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
858 /* Setup link and flow control */
859 ret_val = e1000e_setup_link(hw);
861 /* Set the transmit descriptor write-back policy */
862 reg_data = er32(TXDCTL(0));
863 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
864 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
865 ew32(TXDCTL(0), reg_data);
867 /* ...for both queues. */
868 reg_data = er32(TXDCTL(1));
869 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
870 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
871 ew32(TXDCTL(1), reg_data);
873 /* Enable retransmit on late collisions */
874 reg_data = er32(TCTL);
875 reg_data |= E1000_TCTL_RTLC;
876 ew32(TCTL, reg_data);
878 /* Configure Gigabit Carry Extend Padding */
879 reg_data = er32(TCTL_EXT);
880 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
881 reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
882 ew32(TCTL_EXT, reg_data);
884 /* Configure Transmit Inter-Packet Gap */
885 reg_data = er32(TIPG);
886 reg_data &= ~E1000_TIPG_IPGT_MASK;
887 reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
888 ew32(TIPG, reg_data);
890 reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
891 reg_data &= ~0x00100000;
892 E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
894 /* default to true to enable the MDIC W/A */
895 hw->dev_spec.e80003es2lan.mdic_wa_enable = true;
897 ret_val = e1000_read_kmrn_reg_80003es2lan(hw,
898 E1000_KMRNCTRLSTA_OFFSET >>
899 E1000_KMRNCTRLSTA_OFFSET_SHIFT,
902 if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
903 E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
904 hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
908 * Clear all of the statistics registers (clear on read). It is
909 * important that we do this after we have tried to establish link
910 * because the symbol error count will increment wildly if there
913 e1000_clear_hw_cntrs_80003es2lan(hw);
919 * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
920 * @hw: pointer to the HW structure
922 * Initializes required hardware-dependent bits needed for normal operation.
924 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
928 /* Transmit Descriptor Control 0 */
929 reg = er32(TXDCTL(0));
931 ew32(TXDCTL(0), reg);
933 /* Transmit Descriptor Control 1 */
934 reg = er32(TXDCTL(1));
936 ew32(TXDCTL(1), reg);
938 /* Transmit Arbitration Control 0 */
940 reg &= ~(0xF << 27); /* 30:27 */
941 if (hw->phy.media_type != e1000_media_type_copper)
945 /* Transmit Arbitration Control 1 */
947 if (er32(TCTL) & E1000_TCTL_MULR)
955 * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
956 * @hw: pointer to the HW structure
958 * Setup some GG82563 PHY registers for obtaining link
960 static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
962 struct e1000_phy_info *phy = &hw->phy;
967 ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
971 data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
972 /* Use 25MHz for both link down and 1000Base-T for Tx clock. */
973 data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
975 ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
981 * MDI/MDI-X = 0 (default)
982 * 0 - Auto for all speeds
985 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
987 ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
991 data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
995 data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
998 data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
1002 data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
1008 * disable_polarity_correction = 0 (default)
1009 * Automatic Correction for Reversed Cable Polarity
1013 data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
1014 if (phy->disable_polarity_correction)
1015 data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
1017 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
1021 /* SW Reset the PHY so all changes take effect */
1022 ret_val = e1000e_commit_phy(hw);
1024 e_dbg("Error Resetting the PHY\n");
1028 /* Bypass Rx and Tx FIFO's */
1029 ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
1030 E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
1031 E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
1032 E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
1036 ret_val = e1000_read_kmrn_reg_80003es2lan(hw,
1037 E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
1041 data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
1042 ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
1043 E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
1048 ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
1052 data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
1053 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
1057 ctrl_ext = er32(CTRL_EXT);
1058 ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
1059 ew32(CTRL_EXT, ctrl_ext);
1061 ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
1066 * Do not init these registers when the HW is in IAMT mode, since the
1067 * firmware will have already initialized them. We only initialize
1068 * them if the HW is not in IAMT mode.
1070 if (!e1000e_check_mng_mode(hw)) {
1071 /* Enable Electrical Idle on the PHY */
1072 data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
1073 ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data);
1077 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data);
1081 data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
1082 ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
1088 * Workaround: Disable padding in Kumeran interface in the MAC
1089 * and in the PHY to avoid CRC errors.
1091 ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
1095 data |= GG82563_ICR_DIS_PADDING;
1096 ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
1104 * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
1105 * @hw: pointer to the HW structure
1107 * Essentially a wrapper for setting up all things "copper" related.
1108 * This is a function pointer entry point called by the mac module.
1110 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
1117 ctrl |= E1000_CTRL_SLU;
1118 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
1122 * Set the mac to wait the maximum time between each
1123 * iteration and increase the max iterations when
1124 * polling the phy; this fixes erroneous timeouts at 10Mbps.
1126 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4),
1130 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
1135 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
1139 ret_val = e1000_read_kmrn_reg_80003es2lan(hw,
1140 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
1144 reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
1145 ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
1146 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
1151 ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw);
1155 ret_val = e1000e_setup_copper_link(hw);
1161 * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up
1162 * @hw: pointer to the HW structure
1163 * @duplex: current duplex setting
1165 * Configure the KMRN interface by applying last minute quirks for
1168 static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw)
1174 if (hw->phy.media_type == e1000_media_type_copper) {
1175 ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed,
1180 if (speed == SPEED_1000)
1181 ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw);
1183 ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex);
1190 * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
1191 * @hw: pointer to the HW structure
1192 * @duplex: current duplex setting
1194 * Configure the KMRN interface by applying last minute quirks for
1197 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
1202 u16 reg_data, reg_data2;
1204 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
1205 ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
1206 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
1211 /* Configure Transmit Inter-Packet Gap */
1213 tipg &= ~E1000_TIPG_IPGT_MASK;
1214 tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
1218 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
1222 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2);
1226 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
1228 if (duplex == HALF_DUPLEX)
1229 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
1231 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
1233 ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
1239 * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
1240 * @hw: pointer to the HW structure
1242 * Configure the KMRN interface by applying last minute quirks for
1243 * gigabit operation.
1245 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
1248 u16 reg_data, reg_data2;
1252 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
1253 ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
1254 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
1259 /* Configure Transmit Inter-Packet Gap */
1261 tipg &= ~E1000_TIPG_IPGT_MASK;
1262 tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
1266 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
1270 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2);
1274 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
1276 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
1277 ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
1283 * e1000_read_kmrn_reg_80003es2lan - Read kumeran register
1284 * @hw: pointer to the HW structure
1285 * @offset: register offset to be read
1286 * @data: pointer to the read data
1288 * Acquire semaphore, then read the PHY register at offset
1289 * using the kumeran interface. The information retrieved is stored in data.
1290 * Release the semaphore before exiting.
1292 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
1298 ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
1302 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
1303 E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
1304 ew32(KMRNCTRLSTA, kmrnctrlsta);
1308 kmrnctrlsta = er32(KMRNCTRLSTA);
1309 *data = (u16)kmrnctrlsta;
1311 e1000_release_mac_csr_80003es2lan(hw);
1317 * e1000_write_kmrn_reg_80003es2lan - Write kumeran register
1318 * @hw: pointer to the HW structure
1319 * @offset: register offset to write to
1320 * @data: data to write at register offset
1322 * Acquire semaphore, then write the data to PHY register
1323 * at the offset using the kumeran interface. Release semaphore
1326 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
1332 ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
1336 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
1337 E1000_KMRNCTRLSTA_OFFSET) | data;
1338 ew32(KMRNCTRLSTA, kmrnctrlsta);
1342 e1000_release_mac_csr_80003es2lan(hw);
1348 * e1000_read_mac_addr_80003es2lan - Read device MAC address
1349 * @hw: pointer to the HW structure
1351 static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
1356 * If there's an alternate MAC address place it in RAR0
1357 * so that it will override the Si installed default perm
1360 ret_val = e1000_check_alt_mac_addr_generic(hw);
1364 ret_val = e1000_read_mac_addr_generic(hw);
1371 * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down
1372 * @hw: pointer to the HW structure
1374 * In the case of a PHY power down to save power, or to turn off link during a
1375 * driver unload, or wake on lan is not enabled, remove the link.
1377 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw)
1379 /* If the management interface is not enabled, then power down */
1380 if (!(hw->mac.ops.check_mng_mode(hw) ||
1381 hw->phy.ops.check_reset_block(hw)))
1382 e1000_power_down_phy_copper(hw);
1388 * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
1389 * @hw: pointer to the HW structure
1391 * Clears the hardware counters by reading the counter registers.
1393 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
1395 e1000e_clear_hw_cntrs_base(hw);
1433 static struct e1000_mac_operations es2_mac_ops = {
1434 .read_mac_addr = e1000_read_mac_addr_80003es2lan,
1435 .id_led_init = e1000e_id_led_init,
1436 .check_mng_mode = e1000e_check_mng_mode_generic,
1437 /* check_for_link dependent on media type */
1438 .cleanup_led = e1000e_cleanup_led_generic,
1439 .clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan,
1440 .get_bus_info = e1000e_get_bus_info_pcie,
1441 .set_lan_id = e1000_set_lan_id_multi_port_pcie,
1442 .get_link_up_info = e1000_get_link_up_info_80003es2lan,
1443 .led_on = e1000e_led_on_generic,
1444 .led_off = e1000e_led_off_generic,
1445 .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
1446 .write_vfta = e1000_write_vfta_generic,
1447 .clear_vfta = e1000_clear_vfta_generic,
1448 .reset_hw = e1000_reset_hw_80003es2lan,
1449 .init_hw = e1000_init_hw_80003es2lan,
1450 .setup_link = e1000e_setup_link,
1451 /* setup_physical_interface dependent on media type */
1452 .setup_led = e1000e_setup_led_generic,
1455 static struct e1000_phy_operations es2_phy_ops = {
1456 .acquire = e1000_acquire_phy_80003es2lan,
1457 .check_polarity = e1000_check_polarity_m88,
1458 .check_reset_block = e1000e_check_reset_block_generic,
1459 .commit = e1000e_phy_sw_reset,
1460 .force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan,
1461 .get_cfg_done = e1000_get_cfg_done_80003es2lan,
1462 .get_cable_length = e1000_get_cable_length_80003es2lan,
1463 .get_info = e1000e_get_phy_info_m88,
1464 .read_reg = e1000_read_phy_reg_gg82563_80003es2lan,
1465 .release = e1000_release_phy_80003es2lan,
1466 .reset = e1000e_phy_hw_reset_generic,
1467 .set_d0_lplu_state = NULL,
1468 .set_d3_lplu_state = e1000e_set_d3_lplu_state,
1469 .write_reg = e1000_write_phy_reg_gg82563_80003es2lan,
1470 .cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan,
1473 static struct e1000_nvm_operations es2_nvm_ops = {
1474 .acquire = e1000_acquire_nvm_80003es2lan,
1475 .read = e1000e_read_nvm_eerd,
1476 .release = e1000_release_nvm_80003es2lan,
1477 .update = e1000e_update_nvm_checksum_generic,
1478 .valid_led_default = e1000e_valid_led_default,
1479 .validate = e1000e_validate_nvm_checksum_generic,
1480 .write = e1000_write_nvm_80003es2lan,
1483 struct e1000_info e1000_es2_info = {
1484 .mac = e1000_80003es2lan,
1485 .flags = FLAG_HAS_HW_VLAN_FILTER
1486 | FLAG_HAS_JUMBO_FRAMES
1488 | FLAG_APME_IN_CTRL3
1489 | FLAG_RX_CSUM_ENABLED
1490 | FLAG_HAS_CTRLEXT_ON_LOAD
1491 | FLAG_RX_NEEDS_RESTART /* errata */
1492 | FLAG_TARC_SET_BIT_ZERO /* errata */
1493 | FLAG_APME_CHECK_PORT_B
1494 | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
1495 | FLAG_TIPG_MEDIUM_FOR_80003ESLAN,
1497 .max_hw_frame_size = DEFAULT_JUMBO,
1498 .get_variants = e1000_get_variants_80003es2lan,
1499 .mac_ops = &es2_mac_ops,
1500 .phy_ops = &es2_phy_ops,
1501 .nvm_ops = &es2_nvm_ops,