1 /*******************************************************************************
2 This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
3 ST Ethernet IPs are built around a Synopsys IP Core.
5 Copyright (C) 2007-2009 STMicroelectronics Ltd
7 This program is free software; you can redistribute it and/or modify it
8 under the terms and conditions of the GNU General Public License,
9 version 2, as published by the Free Software Foundation.
11 This program is distributed in the hope it will be useful, but WITHOUT
12 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
13 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
16 You should have received a copy of the GNU General Public License along with
17 this program; if not, write to the Free Software Foundation, Inc.,
18 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
20 The full GNU General Public License is included in this distribution in
21 the file called "COPYING".
23 Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
25 Documentation available at:
26 http://www.stlinux.com
28 https://bugzilla.stlinux.com/
29 *******************************************************************************/
31 #include <linux/module.h>
32 #include <linux/init.h>
33 #include <linux/kernel.h>
34 #include <linux/interrupt.h>
35 #include <linux/netdevice.h>
36 #include <linux/etherdevice.h>
37 #include <linux/platform_device.h>
39 #include <linux/tcp.h>
40 #include <linux/skbuff.h>
41 #include <linux/ethtool.h>
42 #include <linux/if_ether.h>
43 #include <linux/crc32.h>
44 #include <linux/mii.h>
45 #include <linux/phy.h>
46 #include <linux/if_vlan.h>
47 #include <linux/dma-mapping.h>
48 #include <linux/stm/soc.h>
51 #define STMMAC_RESOURCE_NAME "stmmaceth"
52 #define PHY_RESOURCE_NAME "stmmacphy"
55 /*#define STMMAC_DEBUG*/
57 #define DBG(nlevel, klevel, fmt, args...) \
58 ((void)(netif_msg_##nlevel(priv) && \
59 printk(KERN_##klevel fmt, ## args)))
61 #define DBG(nlevel, klevel, fmt, args...) do { } while (0)
64 #undef STMMAC_RX_DEBUG
65 /*#define STMMAC_RX_DEBUG*/
66 #ifdef STMMAC_RX_DEBUG
67 #define RX_DBG(fmt, args...) printk(fmt, ## args)
69 #define RX_DBG(fmt, args...) do { } while (0)
72 #undef STMMAC_XMIT_DEBUG
73 /*#define STMMAC_XMIT_DEBUG*/
74 #ifdef STMMAC_TX_DEBUG
75 #define TX_DBG(fmt, args...) printk(fmt, ## args)
77 #define TX_DBG(fmt, args...) do { } while (0)
80 #define STMMAC_ALIGN(x) L1_CACHE_ALIGN(x)
81 #define JUMBO_LEN 9000
83 /* Module parameters */
84 #define TX_TIMEO 5000 /* default 5 seconds */
85 static int watchdog = TX_TIMEO;
86 module_param(watchdog, int, S_IRUGO | S_IWUSR);
87 MODULE_PARM_DESC(watchdog, "Transmit timeout in milliseconds");
89 static int debug = -1; /* -1: default, 0: no output, 16: all */
90 module_param(debug, int, S_IRUGO | S_IWUSR);
91 MODULE_PARM_DESC(debug, "Message Level (0: no output, 16: all)");
93 static int phyaddr = -1;
94 module_param(phyaddr, int, S_IRUGO);
95 MODULE_PARM_DESC(phyaddr, "Physical device address");
97 #define DMA_TX_SIZE 256
98 static int dma_txsize = DMA_TX_SIZE;
99 module_param(dma_txsize, int, S_IRUGO | S_IWUSR);
100 MODULE_PARM_DESC(dma_txsize, "Number of descriptors in the TX list");
102 #define DMA_RX_SIZE 256
103 static int dma_rxsize = DMA_RX_SIZE;
104 module_param(dma_rxsize, int, S_IRUGO | S_IWUSR);
105 MODULE_PARM_DESC(dma_rxsize, "Number of descriptors in the RX list");
107 static int flow_ctrl = FLOW_OFF;
108 module_param(flow_ctrl, int, S_IRUGO | S_IWUSR);
109 MODULE_PARM_DESC(flow_ctrl, "Flow control ability [on/off]");
111 static int pause = PAUSE_TIME;
112 module_param(pause, int, S_IRUGO | S_IWUSR);
113 MODULE_PARM_DESC(pause, "Flow Control Pause Time");
115 #define TC_DEFAULT 64
116 static int tc = TC_DEFAULT;
117 module_param(tc, int, S_IRUGO | S_IWUSR);
118 MODULE_PARM_DESC(tc, "DMA threshold control value");
120 #define RX_NO_COALESCE 1 /* Always interrupt on completion */
121 #define TX_NO_COALESCE -1 /* No moderation by default */
123 /* Pay attention to tune this parameter; take care of both
124 * hardware capability and network stabitily/performance impact.
125 * Many tests showed that ~4ms latency seems to be good enough. */
126 #ifdef CONFIG_STMMAC_TIMER
127 #define DEFAULT_PERIODIC_RATE 256
128 static int tmrate = DEFAULT_PERIODIC_RATE;
129 module_param(tmrate, int, S_IRUGO | S_IWUSR);
130 MODULE_PARM_DESC(tmrate, "External timer freq. (default: 256Hz)");
133 #define DMA_BUFFER_SIZE BUF_SIZE_2KiB
134 static int buf_sz = DMA_BUFFER_SIZE;
135 module_param(buf_sz, int, S_IRUGO | S_IWUSR);
136 MODULE_PARM_DESC(buf_sz, "DMA buffer size");
138 /* In case of Giga ETH, we can enable/disable the COE for the
139 * transmit HW checksum computation.
140 * Note that, if tx csum is off in HW, SG will be still supported. */
141 static int tx_coe = HW_CSUM;
142 module_param(tx_coe, int, S_IRUGO | S_IWUSR);
143 MODULE_PARM_DESC(tx_coe, "GMAC COE type 2 [on/off]");
145 static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
146 NETIF_MSG_LINK | NETIF_MSG_IFUP |
147 NETIF_MSG_IFDOWN | NETIF_MSG_TIMER);
149 static irqreturn_t stmmac_interrupt(int irq, void *dev_id);
150 static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev);
153 * stmmac_verify_args - verify the driver parameters.
154 * Description: it verifies if some wrong parameter is passed to the driver.
155 * Note that wrong parameters are replaced with the default values.
157 static void stmmac_verify_args(void)
159 if (unlikely(watchdog < 0))
161 if (unlikely(dma_rxsize < 0))
162 dma_rxsize = DMA_RX_SIZE;
163 if (unlikely(dma_txsize < 0))
164 dma_txsize = DMA_TX_SIZE;
165 if (unlikely((buf_sz < DMA_BUFFER_SIZE) || (buf_sz > BUF_SIZE_16KiB)))
166 buf_sz = DMA_BUFFER_SIZE;
167 if (unlikely(flow_ctrl > 1))
168 flow_ctrl = FLOW_AUTO;
169 else if (likely(flow_ctrl < 0))
170 flow_ctrl = FLOW_OFF;
171 if (unlikely((pause < 0) || (pause > 0xffff)))
177 #if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
178 static void print_pkt(unsigned char *buf, int len)
181 pr_info("len = %d byte, buf addr: 0x%p", len, buf);
182 for (j = 0; j < len; j++) {
184 pr_info("\n %03x:", j);
185 pr_info(" %02x", buf[j]);
192 /* minimum number of free TX descriptors required to wake up TX process */
193 #define STMMAC_TX_THRESH(x) (x->dma_tx_size/4)
195 static inline u32 stmmac_tx_avail(struct stmmac_priv *priv)
197 return priv->dirty_tx + priv->dma_tx_size - priv->cur_tx - 1;
202 * @dev: net device structure
203 * Description: it adjusts the link parameters.
205 static void stmmac_adjust_link(struct net_device *dev)
207 struct stmmac_priv *priv = netdev_priv(dev);
208 struct phy_device *phydev = priv->phydev;
209 unsigned long ioaddr = dev->base_addr;
212 unsigned int fc = priv->flow_ctrl, pause_time = priv->pause;
217 DBG(probe, DEBUG, "stmmac_adjust_link: called. address %d link %d\n",
218 phydev->addr, phydev->link);
220 spin_lock_irqsave(&priv->lock, flags);
222 u32 ctrl = readl(ioaddr + MAC_CTRL_REG);
224 /* Now we make sure that we can be in full duplex mode.
225 * If not, we operate in half-duplex mode. */
226 if (phydev->duplex != priv->oldduplex) {
228 if (!(phydev->duplex))
229 ctrl &= ~priv->mac_type->hw.link.duplex;
231 ctrl |= priv->mac_type->hw.link.duplex;
232 priv->oldduplex = phydev->duplex;
234 /* Flow Control operation */
236 priv->mac_type->ops->flow_ctrl(ioaddr, phydev->duplex,
239 if (phydev->speed != priv->speed) {
241 switch (phydev->speed) {
243 if (likely(priv->is_gmac))
244 ctrl &= ~priv->mac_type->hw.link.port;
249 ctrl |= priv->mac_type->hw.link.port;
250 if (phydev->speed == SPEED_100) {
252 priv->mac_type->hw.link.
256 ~(priv->mac_type->hw.
260 ctrl &= ~priv->mac_type->hw.link.port;
262 priv->fix_mac_speed(priv->bsp_priv,
266 if (netif_msg_link(priv))
267 pr_warning("%s: Speed (%d) is not 10"
268 " or 100!\n", dev->name, phydev->speed);
272 priv->speed = phydev->speed;
275 writel(ctrl, ioaddr + MAC_CTRL_REG);
277 if (!priv->oldlink) {
281 } else if (priv->oldlink) {
285 priv->oldduplex = -1;
288 if (new_state && netif_msg_link(priv))
289 phy_print_status(phydev);
291 spin_unlock_irqrestore(&priv->lock, flags);
293 DBG(probe, DEBUG, "stmmac_adjust_link: exiting\n");
297 * stmmac_init_phy - PHY initialization
298 * @dev: net device structure
299 * Description: it initializes the driver's PHY state, and attaches the PHY
304 static int stmmac_init_phy(struct net_device *dev)
306 struct stmmac_priv *priv = netdev_priv(dev);
307 struct phy_device *phydev;
308 char phy_id[BUS_ID_SIZE]; /* PHY to connect */
309 char bus_id[BUS_ID_SIZE];
313 priv->oldduplex = -1;
315 if (priv->phy_addr == -1) {
316 /* We don't have a PHY, so do nothing */
320 snprintf(bus_id, MII_BUS_ID_SIZE, "%x", priv->bus_id);
321 snprintf(phy_id, BUS_ID_SIZE, PHY_ID_FMT, bus_id, priv->phy_addr);
322 pr_debug("stmmac_init_phy: trying to attach to %s\n", phy_id);
324 phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0,
325 priv->phy_interface);
327 if (IS_ERR(phydev)) {
328 pr_err("%s: Could not attach to PHY\n", dev->name);
329 return PTR_ERR(phydev);
333 * Broken HW is sometimes missing the pull-up resistor on the
334 * MDIO line, which results in reads to non-existent devices returning
335 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
337 * Note: phydev->phy_id is the result of reading the UID PHY registers.
339 if (phydev->phy_id == 0) {
340 phy_disconnect(phydev);
343 pr_debug("stmmac_init_phy: %s: attached to PHY (UID 0x%x)"
344 " Link = %d\n", dev->name, phydev->phy_id, phydev->link);
346 priv->phydev = phydev;
351 static inline void stmmac_mac_enable_rx(unsigned long ioaddr)
353 u32 value = readl(ioaddr + MAC_CTRL_REG);
354 value |= MAC_RNABLE_RX;
355 /* Set the RE (receive enable bit into the MAC CTRL register). */
356 writel(value, ioaddr + MAC_CTRL_REG);
359 static inline void stmmac_mac_enable_tx(unsigned long ioaddr)
361 u32 value = readl(ioaddr + MAC_CTRL_REG);
362 value |= MAC_ENABLE_TX;
363 /* Set the TE (transmit enable bit into the MAC CTRL register). */
364 writel(value, ioaddr + MAC_CTRL_REG);
367 static inline void stmmac_mac_disable_rx(unsigned long ioaddr)
369 u32 value = readl(ioaddr + MAC_CTRL_REG);
370 value &= ~MAC_RNABLE_RX;
371 writel(value, ioaddr + MAC_CTRL_REG);
374 static inline void stmmac_mac_disable_tx(unsigned long ioaddr)
376 u32 value = readl(ioaddr + MAC_CTRL_REG);
377 value &= ~MAC_ENABLE_TX;
378 writel(value, ioaddr + MAC_CTRL_REG);
383 * @p: pointer to the ring.
384 * @size: size of the ring.
385 * Description: display all the descriptors within the ring.
387 static void display_ring(struct dma_desc *p, int size)
395 for (i = 0; i < size; i++) {
396 struct tmp_s *x = (struct tmp_s *)(p + i);
397 pr_info("\t%d [0x%x]: DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
398 i, (unsigned int)virt_to_phys(&p[i]),
399 (unsigned int)(x->a), (unsigned int)((x->a) >> 32),
406 * init_dma_desc_rings - init the RX/TX descriptor rings
407 * @dev: net device structure
408 * Description: this function initializes the DMA RX/TX descriptors
409 * and allocates the socket buffers.
411 static void init_dma_desc_rings(struct net_device *dev)
414 struct stmmac_priv *priv = netdev_priv(dev);
416 unsigned int txsize = priv->dma_tx_size;
417 unsigned int rxsize = priv->dma_rx_size;
418 unsigned int bfsize = priv->dma_buf_sz;
419 int buff2_needed = 0, dis_ic = 0;
421 /* Set the Buffer size according to the MTU;
422 * indeed, in case of jumbo we need to bump-up the buffer sizes.
424 if (unlikely(dev->mtu >= BUF_SIZE_8KiB))
425 bfsize = BUF_SIZE_16KiB;
426 else if (unlikely(dev->mtu >= BUF_SIZE_4KiB))
427 bfsize = BUF_SIZE_8KiB;
428 else if (unlikely(dev->mtu >= BUF_SIZE_2KiB))
429 bfsize = BUF_SIZE_4KiB;
430 else if (unlikely(dev->mtu >= DMA_BUFFER_SIZE))
431 bfsize = BUF_SIZE_2KiB;
433 bfsize = DMA_BUFFER_SIZE;
435 #ifdef CONFIG_STMMAC_TIMER
436 /* Disable interrupts on completion for the reception if timer is on */
437 if (likely(priv->tm->enable))
440 /* If the MTU exceeds 8k so use the second buffer in the chain */
441 if (bfsize >= BUF_SIZE_8KiB)
444 DBG(probe, INFO, "stmmac: txsize %d, rxsize %d, bfsize %d\n",
445 txsize, rxsize, bfsize);
447 priv->rx_skbuff_dma = kmalloc(rxsize * sizeof(dma_addr_t), GFP_KERNEL);
449 kmalloc(sizeof(struct sk_buff *) * rxsize, GFP_KERNEL);
451 (struct dma_desc *)dma_alloc_coherent(priv->device,
453 sizeof(struct dma_desc),
456 priv->tx_skbuff = kmalloc(sizeof(struct sk_buff *) * txsize,
459 (struct dma_desc *)dma_alloc_coherent(priv->device,
461 sizeof(struct dma_desc),
465 if ((priv->dma_rx == NULL) || (priv->dma_tx == NULL)) {
466 pr_err("%s:ERROR allocating the DMA Tx/Rx desc\n", __func__);
470 DBG(probe, INFO, "stmmac (%s) DMA desc rings: virt addr (Rx %p, "
471 "Tx %p)\n\tDMA phy addr (Rx 0x%08x, Tx 0x%08x)\n",
472 dev->name, priv->dma_rx, priv->dma_tx,
473 (unsigned int)priv->dma_rx_phy, (unsigned int)priv->dma_tx_phy);
475 /* RX INITIALIZATION */
476 DBG(probe, INFO, "stmmac: SKB addresses:\n"
477 "skb\t\tskb data\tdma data\n");
479 for (i = 0; i < rxsize; i++) {
480 struct dma_desc *p = priv->dma_rx + i;
482 skb = netdev_alloc_skb_ip_align(dev, bfsize);
483 if (unlikely(skb == NULL)) {
484 pr_err("%s: Rx init fails; skb is NULL\n", __func__);
487 priv->rx_skbuff[i] = skb;
488 priv->rx_skbuff_dma[i] = dma_map_single(priv->device, skb->data,
489 bfsize, DMA_FROM_DEVICE);
491 p->des2 = priv->rx_skbuff_dma[i];
492 if (unlikely(buff2_needed))
493 p->des3 = p->des2 + BUF_SIZE_8KiB;
494 DBG(probe, INFO, "[%p]\t[%p]\t[%x]\n", priv->rx_skbuff[i],
495 priv->rx_skbuff[i]->data, priv->rx_skbuff_dma[i]);
498 priv->dirty_rx = (unsigned int)(i - rxsize);
499 priv->dma_buf_sz = bfsize;
502 /* TX INITIALIZATION */
503 for (i = 0; i < txsize; i++) {
504 priv->tx_skbuff[i] = NULL;
505 priv->dma_tx[i].des2 = 0;
510 /* Clear the Rx/Tx descriptors */
511 priv->mac_type->ops->init_rx_desc(priv->dma_rx, rxsize, dis_ic);
512 priv->mac_type->ops->init_tx_desc(priv->dma_tx, txsize);
514 if (netif_msg_hw(priv)) {
515 pr_info("RX descriptor ring:\n");
516 display_ring(priv->dma_rx, rxsize);
517 pr_info("TX descriptor ring:\n");
518 display_ring(priv->dma_tx, txsize);
523 static void dma_free_rx_skbufs(struct stmmac_priv *priv)
527 for (i = 0; i < priv->dma_rx_size; i++) {
528 if (priv->rx_skbuff[i]) {
529 dma_unmap_single(priv->device, priv->rx_skbuff_dma[i],
530 priv->dma_buf_sz, DMA_FROM_DEVICE);
531 dev_kfree_skb_any(priv->rx_skbuff[i]);
533 priv->rx_skbuff[i] = NULL;
538 static void dma_free_tx_skbufs(struct stmmac_priv *priv)
542 for (i = 0; i < priv->dma_tx_size; i++) {
543 if (priv->tx_skbuff[i] != NULL) {
544 struct dma_desc *p = priv->dma_tx + i;
546 dma_unmap_single(priv->device, p->des2,
547 priv->mac_type->ops->get_tx_len(p),
549 dev_kfree_skb_any(priv->tx_skbuff[i]);
550 priv->tx_skbuff[i] = NULL;
556 static void free_dma_desc_resources(struct stmmac_priv *priv)
558 /* Release the DMA TX/RX socket buffers */
559 dma_free_rx_skbufs(priv);
560 dma_free_tx_skbufs(priv);
562 /* Free the region of consistent memory previously allocated for
564 dma_free_coherent(priv->device,
565 priv->dma_tx_size * sizeof(struct dma_desc),
566 priv->dma_tx, priv->dma_tx_phy);
567 dma_free_coherent(priv->device,
568 priv->dma_rx_size * sizeof(struct dma_desc),
569 priv->dma_rx, priv->dma_rx_phy);
570 kfree(priv->rx_skbuff_dma);
571 kfree(priv->rx_skbuff);
572 kfree(priv->tx_skbuff);
578 * stmmac_dma_start_tx
579 * @ioaddr: device I/O address
580 * Description: this function starts the DMA tx process.
582 static void stmmac_dma_start_tx(unsigned long ioaddr)
584 u32 value = readl(ioaddr + DMA_CONTROL);
585 value |= DMA_CONTROL_ST;
586 writel(value, ioaddr + DMA_CONTROL);
590 static void stmmac_dma_stop_tx(unsigned long ioaddr)
592 u32 value = readl(ioaddr + DMA_CONTROL);
593 value &= ~DMA_CONTROL_ST;
594 writel(value, ioaddr + DMA_CONTROL);
599 * stmmac_dma_start_rx
600 * @ioaddr: device I/O address
601 * Description: this function starts the DMA rx process.
603 static void stmmac_dma_start_rx(unsigned long ioaddr)
605 u32 value = readl(ioaddr + DMA_CONTROL);
606 value |= DMA_CONTROL_SR;
607 writel(value, ioaddr + DMA_CONTROL);
612 static void stmmac_dma_stop_rx(unsigned long ioaddr)
614 u32 value = readl(ioaddr + DMA_CONTROL);
615 value &= ~DMA_CONTROL_SR;
616 writel(value, ioaddr + DMA_CONTROL);
622 * stmmac_dma_operation_mode - HW DMA operation mode
623 * @priv : pointer to the private device structure.
624 * Description: it sets the DMA operation mode: tx/rx DMA thresholds
625 * or Store-And-Forward capability. It also verifies the COE for the
626 * transmission in case of Giga ETH.
628 static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
630 if (!priv->is_gmac) {
632 priv->mac_type->ops->dma_mode(priv->dev->base_addr, tc, 0);
633 priv->tx_coe = NO_HW_CSUM;
635 if ((priv->dev->mtu <= ETH_DATA_LEN) && (tx_coe)) {
636 priv->mac_type->ops->dma_mode(priv->dev->base_addr,
637 SF_DMA_MODE, SF_DMA_MODE);
639 priv->tx_coe = HW_CSUM;
641 /* Checksum computation is performed in software. */
642 priv->mac_type->ops->dma_mode(priv->dev->base_addr, tc,
644 priv->tx_coe = NO_HW_CSUM;
647 tx_coe = priv->tx_coe;
654 * show_tx_process_state
655 * @status: tx descriptor status field
656 * Description: it shows the Transmit Process State for CSR5[22:20]
658 static void show_tx_process_state(unsigned int status)
661 state = (status & DMA_STATUS_TS_MASK) >> DMA_STATUS_TS_SHIFT;
665 pr_info("- TX (Stopped): Reset or Stop command\n");
668 pr_info("- TX (Running):Fetching the Tx desc\n");
671 pr_info("- TX (Running): Waiting for end of tx\n");
674 pr_info("- TX (Running): Reading the data "
675 "and queuing the data into the Tx buf\n");
678 pr_info("- TX (Suspended): Tx Buff Underflow "
679 "or an unavailable Transmit descriptor\n");
682 pr_info("- TX (Running): Closing Tx descriptor\n");
691 * show_rx_process_state
692 * @status: rx descriptor status field
693 * Description: it shows the Receive Process State for CSR5[19:17]
695 static void show_rx_process_state(unsigned int status)
698 state = (status & DMA_STATUS_RS_MASK) >> DMA_STATUS_RS_SHIFT;
702 pr_info("- RX (Stopped): Reset or Stop command\n");
705 pr_info("- RX (Running): Fetching the Rx desc\n");
708 pr_info("- RX (Running):Checking for end of pkt\n");
711 pr_info("- RX (Running): Waiting for Rx pkt\n");
714 pr_info("- RX (Suspended): Unavailable Rx buf\n");
717 pr_info("- RX (Running): Closing Rx descriptor\n");
720 pr_info("- RX(Running): Flushing the current frame"
721 " from the Rx buf\n");
724 pr_info("- RX (Running): Queuing the Rx frame"
725 " from the Rx buf into memory\n");
736 * @priv: private driver structure
737 * Description: it reclaims resources after transmission completes.
739 static void stmmac_tx(struct stmmac_priv *priv)
741 unsigned int txsize = priv->dma_tx_size;
742 unsigned long ioaddr = priv->dev->base_addr;
744 while (priv->dirty_tx != priv->cur_tx) {
746 unsigned int entry = priv->dirty_tx % txsize;
747 struct sk_buff *skb = priv->tx_skbuff[entry];
748 struct dma_desc *p = priv->dma_tx + entry;
750 /* Check if the descriptor is owned by the DMA. */
751 if (priv->mac_type->ops->get_tx_owner(p))
754 /* Verify tx error by looking at the last segment */
755 last = priv->mac_type->ops->get_tx_ls(p);
758 priv->mac_type->ops->tx_status(&priv->dev->stats,
761 if (likely(tx_error == 0)) {
762 priv->dev->stats.tx_packets++;
763 priv->xstats.tx_pkt_n++;
765 priv->dev->stats.tx_errors++;
767 TX_DBG("%s: curr %d, dirty %d\n", __func__,
768 priv->cur_tx, priv->dirty_tx);
771 dma_unmap_single(priv->device, p->des2,
772 priv->mac_type->ops->get_tx_len(p),
774 if (unlikely(p->des3))
777 if (likely(skb != NULL)) {
779 * If there's room in the queue (limit it to size)
780 * we add this skb back into the pool,
781 * if it's the right size.
783 if ((skb_queue_len(&priv->rx_recycle) <
784 priv->dma_rx_size) &&
785 skb_recycle_check(skb, priv->dma_buf_sz))
786 __skb_queue_head(&priv->rx_recycle, skb);
790 priv->tx_skbuff[entry] = NULL;
793 priv->mac_type->ops->release_tx_desc(p);
795 entry = (++priv->dirty_tx) % txsize;
797 if (unlikely(netif_queue_stopped(priv->dev) &&
798 stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv))) {
799 netif_tx_lock(priv->dev);
800 if (netif_queue_stopped(priv->dev) &&
801 stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv)) {
802 TX_DBG("%s: restart transmit\n", __func__);
803 netif_wake_queue(priv->dev);
805 netif_tx_unlock(priv->dev);
810 static inline void stmmac_enable_irq(struct stmmac_priv *priv)
812 #ifdef CONFIG_STMMAC_TIMER
813 if (likely(priv->tm->enable))
814 priv->tm->timer_start(tmrate);
817 writel(DMA_INTR_DEFAULT_MASK, priv->dev->base_addr + DMA_INTR_ENA);
820 static inline void stmmac_disable_irq(struct stmmac_priv *priv)
822 #ifdef CONFIG_STMMAC_TIMER
823 if (likely(priv->tm->enable))
824 priv->tm->timer_stop();
827 writel(0, priv->dev->base_addr + DMA_INTR_ENA);
830 static int stmmac_has_work(struct stmmac_priv *priv)
832 unsigned int has_work = 0;
833 int rxret, tx_work = 0;
835 rxret = priv->mac_type->ops->get_rx_owner(priv->dma_rx +
836 (priv->cur_rx % priv->dma_rx_size));
838 if (priv->dirty_tx != priv->cur_tx)
841 if (likely(!rxret || tx_work))
847 static inline void _stmmac_schedule(struct stmmac_priv *priv)
849 if (likely(stmmac_has_work(priv))) {
850 stmmac_disable_irq(priv);
851 napi_schedule(&priv->napi);
855 #ifdef CONFIG_STMMAC_TIMER
856 void stmmac_schedule(struct net_device *dev)
858 struct stmmac_priv *priv = netdev_priv(dev);
860 priv->xstats.sched_timer_n++;
862 _stmmac_schedule(priv);
867 static void stmmac_no_timer_started(unsigned int x)
871 static void stmmac_no_timer_stopped(void)
878 * @priv: pointer to the private device structure
879 * Description: it cleans the descriptors and restarts the transmission
882 static void stmmac_tx_err(struct stmmac_priv *priv)
884 netif_stop_queue(priv->dev);
886 stmmac_dma_stop_tx(priv->dev->base_addr);
887 dma_free_tx_skbufs(priv);
888 priv->mac_type->ops->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
891 stmmac_dma_start_tx(priv->dev->base_addr);
893 priv->dev->stats.tx_errors++;
894 netif_wake_queue(priv->dev);
900 * stmmac_dma_interrupt - Interrupt handler for the driver
901 * @dev: net device structure
902 * Description: Interrupt handler for the driver (DMA).
904 static void stmmac_dma_interrupt(struct net_device *dev)
906 unsigned long ioaddr = dev->base_addr;
907 struct stmmac_priv *priv = netdev_priv(dev);
908 /* read the status register (CSR5) */
909 u32 intr_status = readl(ioaddr + DMA_STATUS);
911 DBG(intr, INFO, "%s: [CSR5: 0x%08x]\n", __func__, intr_status);
914 /* It displays the DMA transmit process state (CSR5 register) */
915 if (netif_msg_tx_done(priv))
916 show_tx_process_state(intr_status);
917 if (netif_msg_rx_status(priv))
918 show_rx_process_state(intr_status);
920 /* ABNORMAL interrupts */
921 if (unlikely(intr_status & DMA_STATUS_AIS)) {
922 DBG(intr, INFO, "CSR5[15] DMA ABNORMAL IRQ: ");
923 if (unlikely(intr_status & DMA_STATUS_UNF)) {
924 DBG(intr, INFO, "transmit underflow\n");
925 if (unlikely(tc != SF_DMA_MODE) && (tc <= 256)) {
926 /* Try to bump up the threshold */
928 priv->mac_type->ops->dma_mode(ioaddr, tc,
930 priv->xstats.threshold = tc;
933 priv->xstats.tx_undeflow_irq++;
935 if (unlikely(intr_status & DMA_STATUS_TJT)) {
936 DBG(intr, INFO, "transmit jabber\n");
937 priv->xstats.tx_jabber_irq++;
939 if (unlikely(intr_status & DMA_STATUS_OVF)) {
940 DBG(intr, INFO, "recv overflow\n");
941 priv->xstats.rx_overflow_irq++;
943 if (unlikely(intr_status & DMA_STATUS_RU)) {
944 DBG(intr, INFO, "receive buffer unavailable\n");
945 priv->xstats.rx_buf_unav_irq++;
947 if (unlikely(intr_status & DMA_STATUS_RPS)) {
948 DBG(intr, INFO, "receive process stopped\n");
949 priv->xstats.rx_process_stopped_irq++;
951 if (unlikely(intr_status & DMA_STATUS_RWT)) {
952 DBG(intr, INFO, "receive watchdog\n");
953 priv->xstats.rx_watchdog_irq++;
955 if (unlikely(intr_status & DMA_STATUS_ETI)) {
956 DBG(intr, INFO, "transmit early interrupt\n");
957 priv->xstats.tx_early_irq++;
959 if (unlikely(intr_status & DMA_STATUS_TPS)) {
960 DBG(intr, INFO, "transmit process stopped\n");
961 priv->xstats.tx_process_stopped_irq++;
964 if (unlikely(intr_status & DMA_STATUS_FBI)) {
965 DBG(intr, INFO, "fatal bus error\n");
966 priv->xstats.fatal_bus_error_irq++;
971 /* TX/RX NORMAL interrupts */
972 if (intr_status & DMA_STATUS_NIS) {
973 priv->xstats.normal_irq_n++;
974 if (likely((intr_status & DMA_STATUS_RI) ||
975 (intr_status & (DMA_STATUS_TI))))
976 _stmmac_schedule(priv);
979 /* Optional hardware blocks, interrupts should be disabled */
980 if (unlikely(intr_status &
981 (DMA_STATUS_GPI | DMA_STATUS_GMI | DMA_STATUS_GLI)))
982 pr_info("%s: unexpected status %08x\n", __func__, intr_status);
984 /* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */
985 writel((intr_status & 0x1ffff), ioaddr + DMA_STATUS);
987 DBG(intr, INFO, "\n\n");
993 * stmmac_open - open entry point of the driver
994 * @dev : pointer to the device structure.
996 * This function is the open entry point of the driver.
998 * 0 on success and an appropriate (-)ve integer as defined in errno.h
1001 static int stmmac_open(struct net_device *dev)
1003 struct stmmac_priv *priv = netdev_priv(dev);
1004 unsigned long ioaddr = dev->base_addr;
1007 /* Check that the MAC address is valid. If its not, refuse
1008 * to bring the device up. The user must specify an
1009 * address using the following linux command:
1010 * ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx */
1011 if (!is_valid_ether_addr(dev->dev_addr)) {
1012 random_ether_addr(dev->dev_addr);
1013 pr_warning("%s: generated random MAC address %pM\n", dev->name,
1017 stmmac_verify_args();
1019 ret = stmmac_init_phy(dev);
1020 if (unlikely(ret)) {
1021 pr_err("%s: Cannot attach to PHY (error: %d)\n", __func__, ret);
1025 /* Request the IRQ lines */
1026 ret = request_irq(dev->irq, stmmac_interrupt,
1027 IRQF_SHARED, dev->name, dev);
1028 if (unlikely(ret < 0)) {
1029 pr_err("%s: ERROR: allocating the IRQ %d (error: %d)\n",
1030 __func__, dev->irq, ret);
1034 #ifdef CONFIG_STMMAC_TIMER
1035 priv->tm = kzalloc(sizeof(struct stmmac_timer *), GFP_KERNEL);
1036 if (unlikely(priv->tm == NULL)) {
1037 pr_err("%s: ERROR: timer memory alloc failed \n", __func__);
1040 priv->tm->freq = tmrate;
1042 /* Test if the external timer can be actually used.
1043 * In case of failure continue without timer. */
1044 if (unlikely((stmmac_open_ext_timer(dev, priv->tm)) < 0)) {
1045 pr_warning("stmmaceth: cannot attach the external timer.\n");
1048 priv->tm->timer_start = stmmac_no_timer_started;
1049 priv->tm->timer_stop = stmmac_no_timer_stopped;
1051 priv->tm->enable = 1;
1054 /* Create and initialize the TX/RX descriptors chains. */
1055 priv->dma_tx_size = STMMAC_ALIGN(dma_txsize);
1056 priv->dma_rx_size = STMMAC_ALIGN(dma_rxsize);
1057 priv->dma_buf_sz = STMMAC_ALIGN(buf_sz);
1058 init_dma_desc_rings(dev);
1060 /* DMA initialization and SW reset */
1061 if (unlikely(priv->mac_type->ops->dma_init(ioaddr,
1062 priv->pbl, priv->dma_tx_phy, priv->dma_rx_phy) < 0)) {
1064 pr_err("%s: DMA initialization failed\n", __func__);
1068 /* Copy the MAC addr into the HW */
1069 priv->mac_type->ops->set_umac_addr(ioaddr, dev->dev_addr, 0);
1070 /* Initialize the MAC Core */
1071 priv->mac_type->ops->core_init(ioaddr);
1075 /* Initialise the MMC (if present) to disable all interrupts. */
1076 writel(0xffffffff, ioaddr + MMC_HIGH_INTR_MASK);
1077 writel(0xffffffff, ioaddr + MMC_LOW_INTR_MASK);
1079 /* Enable the MAC Rx/Tx */
1080 stmmac_mac_enable_rx(ioaddr);
1081 stmmac_mac_enable_tx(ioaddr);
1083 /* Set the HW DMA mode and the COE */
1084 stmmac_dma_operation_mode(priv);
1086 /* Extra statistics */
1087 memset(&priv->xstats, 0, sizeof(struct stmmac_extra_stats));
1088 priv->xstats.threshold = tc;
1090 /* Start the ball rolling... */
1091 DBG(probe, DEBUG, "%s: DMA RX/TX processes started...\n", dev->name);
1092 stmmac_dma_start_tx(ioaddr);
1093 stmmac_dma_start_rx(ioaddr);
1095 #ifdef CONFIG_STMMAC_TIMER
1096 priv->tm->timer_start(tmrate);
1098 /* Dump DMA/MAC registers */
1099 if (netif_msg_hw(priv)) {
1100 priv->mac_type->ops->dump_mac_regs(ioaddr);
1101 priv->mac_type->ops->dump_dma_regs(ioaddr);
1105 phy_start(priv->phydev);
1107 napi_enable(&priv->napi);
1108 skb_queue_head_init(&priv->rx_recycle);
1109 netif_start_queue(dev);
1114 * stmmac_release - close entry point of the driver
1115 * @dev : device pointer.
1117 * This is the stop entry point of the driver.
1119 static int stmmac_release(struct net_device *dev)
1121 struct stmmac_priv *priv = netdev_priv(dev);
1123 /* Stop and disconnect the PHY */
1125 phy_stop(priv->phydev);
1126 phy_disconnect(priv->phydev);
1127 priv->phydev = NULL;
1130 netif_stop_queue(dev);
1132 #ifdef CONFIG_STMMAC_TIMER
1133 /* Stop and release the timer */
1134 stmmac_close_ext_timer();
1135 if (priv->tm != NULL)
1138 napi_disable(&priv->napi);
1139 skb_queue_purge(&priv->rx_recycle);
1141 /* Free the IRQ lines */
1142 free_irq(dev->irq, dev);
1144 /* Stop TX/RX DMA and clear the descriptors */
1145 stmmac_dma_stop_tx(dev->base_addr);
1146 stmmac_dma_stop_rx(dev->base_addr);
1148 /* Release and free the Rx/Tx resources */
1149 free_dma_desc_resources(priv);
1151 /* Disable the MAC core */
1152 stmmac_mac_disable_tx(dev->base_addr);
1153 stmmac_mac_disable_rx(dev->base_addr);
1155 netif_carrier_off(dev);
1161 * To perform emulated hardware segmentation on skb.
1163 static int stmmac_sw_tso(struct stmmac_priv *priv, struct sk_buff *skb)
1165 struct sk_buff *segs, *curr_skb;
1166 int gso_segs = skb_shinfo(skb)->gso_segs;
1168 /* Estimate the number of fragments in the worst case */
1169 if (unlikely(stmmac_tx_avail(priv) < gso_segs)) {
1170 netif_stop_queue(priv->dev);
1171 TX_DBG(KERN_ERR "%s: TSO BUG! Tx Ring full when queue awake\n",
1173 if (stmmac_tx_avail(priv) < gso_segs)
1174 return NETDEV_TX_BUSY;
1176 netif_wake_queue(priv->dev);
1178 TX_DBG("\tstmmac_sw_tso: segmenting: skb %p (len %d)\n",
1181 segs = skb_gso_segment(skb, priv->dev->features & ~NETIF_F_TSO);
1182 if (unlikely(IS_ERR(segs)))
1188 TX_DBG("\t\tcurrent skb->len: %d, *curr %p,"
1189 "*next %p\n", curr_skb->len, curr_skb, segs);
1190 curr_skb->next = NULL;
1191 stmmac_xmit(curr_skb, priv->dev);
1197 return NETDEV_TX_OK;
1200 static unsigned int stmmac_handle_jumbo_frames(struct sk_buff *skb,
1201 struct net_device *dev,
1204 struct stmmac_priv *priv = netdev_priv(dev);
1205 unsigned int nopaged_len = skb_headlen(skb);
1206 unsigned int txsize = priv->dma_tx_size;
1207 unsigned int entry = priv->cur_tx % txsize;
1208 struct dma_desc *desc = priv->dma_tx + entry;
1210 if (nopaged_len > BUF_SIZE_8KiB) {
1212 int buf2_size = nopaged_len - BUF_SIZE_8KiB;
1214 desc->des2 = dma_map_single(priv->device, skb->data,
1215 BUF_SIZE_8KiB, DMA_TO_DEVICE);
1216 desc->des3 = desc->des2 + BUF_SIZE_4KiB;
1217 priv->mac_type->ops->prepare_tx_desc(desc, 1, BUF_SIZE_8KiB,
1220 entry = (++priv->cur_tx) % txsize;
1221 desc = priv->dma_tx + entry;
1223 desc->des2 = dma_map_single(priv->device,
1224 skb->data + BUF_SIZE_8KiB,
1225 buf2_size, DMA_TO_DEVICE);
1226 desc->des3 = desc->des2 + BUF_SIZE_4KiB;
1227 priv->mac_type->ops->prepare_tx_desc(desc, 0,
1228 buf2_size, csum_insertion);
1229 priv->mac_type->ops->set_tx_owner(desc);
1230 priv->tx_skbuff[entry] = NULL;
1232 desc->des2 = dma_map_single(priv->device, skb->data,
1233 nopaged_len, DMA_TO_DEVICE);
1234 desc->des3 = desc->des2 + BUF_SIZE_4KiB;
1235 priv->mac_type->ops->prepare_tx_desc(desc, 1, nopaged_len,
1243 * @skb : the socket buffer
1244 * @dev : device pointer
1245 * Description : Tx entry point of the driver.
1247 static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
1249 struct stmmac_priv *priv = netdev_priv(dev);
1250 unsigned int txsize = priv->dma_tx_size;
1252 int i, csum_insertion = 0;
1253 int nfrags = skb_shinfo(skb)->nr_frags;
1254 struct dma_desc *desc, *first;
1256 if (unlikely(stmmac_tx_avail(priv) < nfrags + 1)) {
1257 if (!netif_queue_stopped(dev)) {
1258 netif_stop_queue(dev);
1259 /* This is a hard error, log it. */
1260 pr_err("%s: BUG! Tx Ring full when queue awake\n",
1263 return NETDEV_TX_BUSY;
1266 entry = priv->cur_tx % txsize;
1268 #ifdef STMMAC_XMIT_DEBUG
1269 if ((skb->len > ETH_FRAME_LEN) || nfrags)
1270 pr_info("stmmac xmit:\n"
1271 "\tskb addr %p - len: %d - nopaged_len: %d\n"
1272 "\tn_frags: %d - ip_summed: %d - %s gso\n",
1273 skb, skb->len, skb_headlen(skb), nfrags, skb->ip_summed,
1274 !skb_is_gso(skb) ? "isn't" : "is");
1277 if (unlikely(skb_is_gso(skb)))
1278 return stmmac_sw_tso(priv, skb);
1280 if (likely((skb->ip_summed == CHECKSUM_PARTIAL))) {
1281 if (likely(priv->tx_coe == NO_HW_CSUM))
1282 skb_checksum_help(skb);
1287 desc = priv->dma_tx + entry;
1290 #ifdef STMMAC_XMIT_DEBUG
1291 if ((nfrags > 0) || (skb->len > ETH_FRAME_LEN))
1292 pr_debug("stmmac xmit: skb len: %d, nopaged_len: %d,\n"
1293 "\t\tn_frags: %d, ip_summed: %d\n",
1294 skb->len, skb_headlen(skb), nfrags, skb->ip_summed);
1296 priv->tx_skbuff[entry] = skb;
1297 if (unlikely(skb->len >= BUF_SIZE_4KiB)) {
1298 entry = stmmac_handle_jumbo_frames(skb, dev, csum_insertion);
1299 desc = priv->dma_tx + entry;
1301 unsigned int nopaged_len = skb_headlen(skb);
1302 desc->des2 = dma_map_single(priv->device, skb->data,
1303 nopaged_len, DMA_TO_DEVICE);
1304 priv->mac_type->ops->prepare_tx_desc(desc, 1, nopaged_len,
1308 for (i = 0; i < nfrags; i++) {
1309 skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
1310 int len = frag->size;
1312 entry = (++priv->cur_tx) % txsize;
1313 desc = priv->dma_tx + entry;
1315 TX_DBG("\t[entry %d] segment len: %d\n", entry, len);
1316 desc->des2 = dma_map_page(priv->device, frag->page,
1318 len, DMA_TO_DEVICE);
1319 priv->tx_skbuff[entry] = NULL;
1320 priv->mac_type->ops->prepare_tx_desc(desc, 0, len,
1322 priv->mac_type->ops->set_tx_owner(desc);
1325 /* Interrupt on completition only for the latest segment */
1326 priv->mac_type->ops->close_tx_desc(desc);
1328 #ifdef CONFIG_STMMAC_TIMER
1329 /* Clean IC while using timer */
1330 if (likely(priv->tm->enable))
1331 priv->mac_type->ops->clear_tx_ic(desc);
1333 /* To avoid raise condition */
1334 priv->mac_type->ops->set_tx_owner(first);
1338 #ifdef STMMAC_XMIT_DEBUG
1339 if (netif_msg_pktdata(priv)) {
1340 pr_info("stmmac xmit: current=%d, dirty=%d, entry=%d, "
1341 "first=%p, nfrags=%d\n",
1342 (priv->cur_tx % txsize), (priv->dirty_tx % txsize),
1343 entry, first, nfrags);
1344 display_ring(priv->dma_tx, txsize);
1345 pr_info(">>> frame to be transmitted: ");
1346 print_pkt(skb->data, skb->len);
1349 if (unlikely(stmmac_tx_avail(priv) <= (MAX_SKB_FRAGS + 1))) {
1350 TX_DBG("%s: stop transmitted packets\n", __func__);
1351 netif_stop_queue(dev);
1354 dev->stats.tx_bytes += skb->len;
1356 /* CSR1 enables the transmit DMA to check for new descriptor */
1357 writel(1, dev->base_addr + DMA_XMT_POLL_DEMAND);
1359 return NETDEV_TX_OK;
1362 static inline void stmmac_rx_refill(struct stmmac_priv *priv)
1364 unsigned int rxsize = priv->dma_rx_size;
1365 int bfsize = priv->dma_buf_sz;
1366 struct dma_desc *p = priv->dma_rx;
1368 for (; priv->cur_rx - priv->dirty_rx > 0; priv->dirty_rx++) {
1369 unsigned int entry = priv->dirty_rx % rxsize;
1370 if (likely(priv->rx_skbuff[entry] == NULL)) {
1371 struct sk_buff *skb;
1373 skb = __skb_dequeue(&priv->rx_recycle);
1375 skb = netdev_alloc_skb_ip_align(priv->dev,
1378 if (unlikely(skb == NULL))
1381 priv->rx_skbuff[entry] = skb;
1382 priv->rx_skbuff_dma[entry] =
1383 dma_map_single(priv->device, skb->data, bfsize,
1386 (p + entry)->des2 = priv->rx_skbuff_dma[entry];
1387 if (unlikely(priv->is_gmac)) {
1388 if (bfsize >= BUF_SIZE_8KiB)
1390 (p + entry)->des2 + BUF_SIZE_8KiB;
1392 RX_DBG(KERN_INFO "\trefill entry #%d\n", entry);
1394 priv->mac_type->ops->set_rx_owner(p + entry);
1399 static int stmmac_rx(struct stmmac_priv *priv, int limit)
1401 unsigned int rxsize = priv->dma_rx_size;
1402 unsigned int entry = priv->cur_rx % rxsize;
1403 unsigned int next_entry;
1404 unsigned int count = 0;
1405 struct dma_desc *p = priv->dma_rx + entry;
1406 struct dma_desc *p_next;
1408 #ifdef STMMAC_RX_DEBUG
1409 if (netif_msg_hw(priv)) {
1410 pr_debug(">>> stmmac_rx: descriptor ring:\n");
1411 display_ring(priv->dma_rx, rxsize);
1415 while (!priv->mac_type->ops->get_rx_owner(p)) {
1423 next_entry = (++priv->cur_rx) % rxsize;
1424 p_next = priv->dma_rx + next_entry;
1427 /* read the status of the incoming frame */
1428 status = (priv->mac_type->ops->rx_status(&priv->dev->stats,
1430 if (unlikely(status == discard_frame))
1431 priv->dev->stats.rx_errors++;
1433 struct sk_buff *skb;
1434 /* Length should omit the CRC */
1436 priv->mac_type->ops->get_rx_frame_len(p) - 4;
1438 #ifdef STMMAC_RX_DEBUG
1439 if (frame_len > ETH_FRAME_LEN)
1440 pr_debug("\tRX frame size %d, COE status: %d\n",
1443 if (netif_msg_hw(priv))
1444 pr_debug("\tdesc: %p [entry %d] buff=0x%x\n",
1447 skb = priv->rx_skbuff[entry];
1448 if (unlikely(!skb)) {
1449 pr_err("%s: Inconsistent Rx descriptor chain\n",
1451 priv->dev->stats.rx_dropped++;
1454 prefetch(skb->data - NET_IP_ALIGN);
1455 priv->rx_skbuff[entry] = NULL;
1457 skb_put(skb, frame_len);
1458 dma_unmap_single(priv->device,
1459 priv->rx_skbuff_dma[entry],
1460 priv->dma_buf_sz, DMA_FROM_DEVICE);
1461 #ifdef STMMAC_RX_DEBUG
1462 if (netif_msg_pktdata(priv)) {
1463 pr_info(" frame received (%dbytes)", frame_len);
1464 print_pkt(skb->data, frame_len);
1467 skb->protocol = eth_type_trans(skb, priv->dev);
1469 if (unlikely(status == csum_none)) {
1470 /* always for the old mac 10/100 */
1471 skb->ip_summed = CHECKSUM_NONE;
1472 netif_receive_skb(skb);
1474 skb->ip_summed = CHECKSUM_UNNECESSARY;
1475 napi_gro_receive(&priv->napi, skb);
1478 priv->dev->stats.rx_packets++;
1479 priv->dev->stats.rx_bytes += frame_len;
1480 priv->dev->last_rx = jiffies;
1483 p = p_next; /* use prefetched values */
1486 stmmac_rx_refill(priv);
1488 priv->xstats.rx_pkt_n += count;
1494 * stmmac_poll - stmmac poll method (NAPI)
1495 * @napi : pointer to the napi structure.
1496 * @budget : maximum number of packets that the current CPU can receive from
1499 * This function implements the the reception process.
1500 * Also it runs the TX completion thread
1502 static int stmmac_poll(struct napi_struct *napi, int budget)
1504 struct stmmac_priv *priv = container_of(napi, struct stmmac_priv, napi);
1507 priv->xstats.poll_n++;
1509 work_done = stmmac_rx(priv, budget);
1511 if (work_done < budget) {
1512 napi_complete(napi);
1513 stmmac_enable_irq(priv);
1520 * @dev : Pointer to net device structure
1521 * Description: this function is called when a packet transmission fails to
1522 * complete within a reasonable tmrate. The driver will mark the error in the
1523 * netdev structure and arrange for the device to be reset to a sane state
1524 * in order to transmit a new packet.
1526 static void stmmac_tx_timeout(struct net_device *dev)
1528 struct stmmac_priv *priv = netdev_priv(dev);
1530 /* Clear Tx resources and restart transmitting again */
1531 stmmac_tx_err(priv);
1535 /* Configuration changes (passed on by ifconfig) */
1536 static int stmmac_config(struct net_device *dev, struct ifmap *map)
1538 if (dev->flags & IFF_UP) /* can't act on a running interface */
1541 /* Don't allow changing the I/O address */
1542 if (map->base_addr != dev->base_addr) {
1543 pr_warning("%s: can't change I/O address\n", dev->name);
1547 /* Don't allow changing the IRQ */
1548 if (map->irq != dev->irq) {
1549 pr_warning("%s: can't change IRQ number %d\n",
1550 dev->name, dev->irq);
1554 /* ignore other fields */
1559 * stmmac_multicast_list - entry point for multicast addressing
1560 * @dev : pointer to the device structure
1562 * This function is a driver entry point which gets called by the kernel
1563 * whenever multicast addresses must be enabled/disabled.
1567 static void stmmac_multicast_list(struct net_device *dev)
1569 struct stmmac_priv *priv = netdev_priv(dev);
1571 spin_lock(&priv->lock);
1572 priv->mac_type->ops->set_filter(dev);
1573 spin_unlock(&priv->lock);
1578 * stmmac_change_mtu - entry point to change MTU size for the device.
1579 * @dev : device pointer.
1580 * @new_mtu : the new MTU size for the device.
1581 * Description: the Maximum Transfer Unit (MTU) is used by the network layer
1582 * to drive packet transmission. Ethernet has an MTU of 1500 octets
1583 * (ETH_DATA_LEN). This value can be changed with ifconfig.
1585 * 0 on success and an appropriate (-)ve integer as defined in errno.h
1588 static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
1590 struct stmmac_priv *priv = netdev_priv(dev);
1593 if (netif_running(dev)) {
1594 pr_err("%s: must be stopped to change its MTU\n", dev->name);
1599 max_mtu = JUMBO_LEN;
1601 max_mtu = ETH_DATA_LEN;
1603 if ((new_mtu < 46) || (new_mtu > max_mtu)) {
1604 pr_err("%s: invalid MTU, max MTU is: %d\n", dev->name, max_mtu);
1613 static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
1615 struct net_device *dev = (struct net_device *)dev_id;
1616 struct stmmac_priv *priv = netdev_priv(dev);
1618 if (unlikely(!dev)) {
1619 pr_err("%s: invalid dev pointer\n", __func__);
1623 if (priv->is_gmac) {
1624 unsigned long ioaddr = dev->base_addr;
1625 /* To handle GMAC own interrupts */
1626 priv->mac_type->ops->host_irq_status(ioaddr);
1628 stmmac_dma_interrupt(dev);
1633 #ifdef CONFIG_NET_POLL_CONTROLLER
1634 /* Polling receive - used by NETCONSOLE and other diagnostic tools
1635 * to allow network I/O with interrupts disabled. */
1636 static void stmmac_poll_controller(struct net_device *dev)
1638 disable_irq(dev->irq);
1639 stmmac_interrupt(dev->irq, dev);
1640 enable_irq(dev->irq);
1645 * stmmac_ioctl - Entry point for the Ioctl
1646 * @dev: Device pointer.
1647 * @rq: An IOCTL specefic structure, that can contain a pointer to
1648 * a proprietary structure used to pass information to the driver.
1649 * @cmd: IOCTL command
1651 * Currently there are no special functionality supported in IOCTL, just the
1652 * phy_mii_ioctl(...) can be invoked.
1654 static int stmmac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1656 struct stmmac_priv *priv = netdev_priv(dev);
1657 int ret = -EOPNOTSUPP;
1659 if (!netif_running(dev))
1669 spin_lock(&priv->lock);
1670 ret = phy_mii_ioctl(priv->phydev, if_mii(rq), cmd);
1671 spin_unlock(&priv->lock);
1678 #ifdef STMMAC_VLAN_TAG_USED
1679 static void stmmac_vlan_rx_register(struct net_device *dev,
1680 struct vlan_group *grp)
1682 struct stmmac_priv *priv = netdev_priv(dev);
1684 DBG(probe, INFO, "%s: Setting vlgrp to %p\n", dev->name, grp);
1686 spin_lock(&priv->lock);
1688 spin_unlock(&priv->lock);
1694 static const struct net_device_ops stmmac_netdev_ops = {
1695 .ndo_open = stmmac_open,
1696 .ndo_start_xmit = stmmac_xmit,
1697 .ndo_stop = stmmac_release,
1698 .ndo_change_mtu = stmmac_change_mtu,
1699 .ndo_set_multicast_list = stmmac_multicast_list,
1700 .ndo_tx_timeout = stmmac_tx_timeout,
1701 .ndo_do_ioctl = stmmac_ioctl,
1702 .ndo_set_config = stmmac_config,
1703 #ifdef STMMAC_VLAN_TAG_USED
1704 .ndo_vlan_rx_register = stmmac_vlan_rx_register,
1706 #ifdef CONFIG_NET_POLL_CONTROLLER
1707 .ndo_poll_controller = stmmac_poll_controller,
1709 .ndo_set_mac_address = eth_mac_addr,
1713 * stmmac_probe - Initialization of the adapter .
1714 * @dev : device pointer
1715 * Description: The function initializes the network device structure for
1716 * the STMMAC driver. It also calls the low level routines
1717 * in order to init the HW (i.e. the DMA engine)
1719 static int stmmac_probe(struct net_device *dev)
1722 struct stmmac_priv *priv = netdev_priv(dev);
1726 dev->netdev_ops = &stmmac_netdev_ops;
1727 stmmac_set_ethtool_ops(dev);
1729 dev->features |= (NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_HIGHDMA);
1730 dev->watchdog_timeo = msecs_to_jiffies(watchdog);
1731 #ifdef STMMAC_VLAN_TAG_USED
1732 /* Both mac100 and gmac support receive VLAN tag detection */
1733 dev->features |= NETIF_F_HW_VLAN_RX;
1735 priv->msg_enable = netif_msg_init(debug, default_msg_level);
1741 priv->flow_ctrl = FLOW_AUTO; /* RX/TX pause on */
1743 priv->pause = pause;
1744 netif_napi_add(dev, &priv->napi, stmmac_poll, 64);
1746 /* Get the MAC address */
1747 priv->mac_type->ops->get_umac_addr(dev->base_addr, dev->dev_addr, 0);
1749 if (!is_valid_ether_addr(dev->dev_addr))
1750 pr_warning("\tno valid MAC address;"
1751 "please, use ifconfig or nwhwconfig!\n");
1753 ret = register_netdev(dev);
1755 pr_err("%s: ERROR %i registering the device\n",
1760 DBG(probe, DEBUG, "%s: Scatter/Gather: %s - HW checksums: %s\n",
1761 dev->name, (dev->features & NETIF_F_SG) ? "on" : "off",
1762 (dev->features & NETIF_F_HW_CSUM) ? "on" : "off");
1764 spin_lock_init(&priv->lock);
1770 * stmmac_mac_device_setup
1771 * @dev : device pointer
1772 * Description: select and initialise the mac device (mac100 or Gmac).
1774 static int stmmac_mac_device_setup(struct net_device *dev)
1776 struct stmmac_priv *priv = netdev_priv(dev);
1777 unsigned long ioaddr = dev->base_addr;
1779 struct mac_device_info *device;
1782 device = gmac_setup(ioaddr);
1784 device = mac100_setup(ioaddr);
1789 priv->mac_type = device;
1791 priv->wolenabled = priv->mac_type->hw.pmt; /* PMT supported */
1792 if (priv->wolenabled == PMT_SUPPORTED)
1793 priv->wolopts = WAKE_MAGIC; /* Magic Frame */
1798 static int stmmacphy_dvr_probe(struct platform_device *pdev)
1800 struct plat_stmmacphy_data *plat_dat;
1801 plat_dat = (struct plat_stmmacphy_data *)((pdev->dev).platform_data);
1803 pr_debug("stmmacphy_dvr_probe: added phy for bus %d\n",
1809 static int stmmacphy_dvr_remove(struct platform_device *pdev)
1814 static struct platform_driver stmmacphy_driver = {
1816 .name = PHY_RESOURCE_NAME,
1818 .probe = stmmacphy_dvr_probe,
1819 .remove = stmmacphy_dvr_remove,
1823 * stmmac_associate_phy
1824 * @dev: pointer to device structure
1825 * @data: points to the private structure.
1826 * Description: Scans through all the PHYs we have registered and checks if
1827 * any are associated with our MAC. If so, then just fill in
1828 * the blanks in our local context structure
1830 static int stmmac_associate_phy(struct device *dev, void *data)
1832 struct stmmac_priv *priv = (struct stmmac_priv *)data;
1833 struct plat_stmmacphy_data *plat_dat;
1835 plat_dat = (struct plat_stmmacphy_data *)(dev->platform_data);
1837 DBG(probe, DEBUG, "%s: checking phy for bus %d\n", __func__,
1840 /* Check that this phy is for the MAC being initialised */
1841 if (priv->bus_id != plat_dat->bus_id)
1844 /* OK, this PHY is connected to the MAC.
1845 Go ahead and get the parameters */
1846 DBG(probe, DEBUG, "%s: OK. Found PHY config\n", __func__);
1848 platform_get_irq_byname(to_platform_device(dev), "phyirq");
1849 DBG(probe, DEBUG, "%s: PHY irq on bus %d is %d\n", __func__,
1850 plat_dat->bus_id, priv->phy_irq);
1852 /* Override with kernel parameters if supplied XXX CRS XXX
1853 * this needs to have multiple instances */
1854 if ((phyaddr >= 0) && (phyaddr <= 31))
1855 plat_dat->phy_addr = phyaddr;
1857 priv->phy_addr = plat_dat->phy_addr;
1858 priv->phy_mask = plat_dat->phy_mask;
1859 priv->phy_interface = plat_dat->interface;
1860 priv->phy_reset = plat_dat->phy_reset;
1862 DBG(probe, DEBUG, "%s: exiting\n", __func__);
1863 return 1; /* forces exit of driver_for_each_device() */
1868 * @pdev: platform device pointer
1869 * Description: the driver is initialized through platform_device.
1871 static int stmmac_dvr_probe(struct platform_device *pdev)
1874 struct resource *res;
1875 unsigned int *addr = NULL;
1876 struct net_device *ndev = NULL;
1877 struct stmmac_priv *priv;
1878 struct plat_stmmacenet_data *plat_dat;
1880 pr_info("STMMAC driver:\n\tplatform registration... ");
1881 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1888 if (!request_mem_region(res->start, (res->end - res->start),
1890 pr_err("%s: ERROR: memory allocation failed"
1891 "cannot get the I/O addr 0x%x\n",
1892 __func__, (unsigned int)res->start);
1897 addr = ioremap(res->start, (res->end - res->start));
1899 pr_err("%s: ERROR: memory mapping failed \n", __func__);
1904 ndev = alloc_etherdev(sizeof(struct stmmac_priv));
1906 pr_err("%s: ERROR: allocating the device\n", __func__);
1911 SET_NETDEV_DEV(ndev, &pdev->dev);
1913 /* Get the MAC information */
1914 ndev->irq = platform_get_irq_byname(pdev, "macirq");
1915 if (ndev->irq == -ENXIO) {
1916 pr_err("%s: ERROR: MAC IRQ configuration "
1917 "information not found\n", __func__);
1922 priv = netdev_priv(ndev);
1923 priv->device = &(pdev->dev);
1925 plat_dat = (struct plat_stmmacenet_data *)((pdev->dev).platform_data);
1926 priv->bus_id = plat_dat->bus_id;
1927 priv->pbl = plat_dat->pbl; /* TLI */
1928 priv->is_gmac = plat_dat->has_gmac; /* GMAC is on board */
1930 platform_set_drvdata(pdev, ndev);
1932 /* Set the I/O base addr */
1933 ndev->base_addr = (unsigned long)addr;
1935 /* MAC HW revice detection */
1936 ret = stmmac_mac_device_setup(ndev);
1940 /* Network Device Registration */
1941 ret = stmmac_probe(ndev);
1945 /* associate a PHY - it is provided by another platform bus */
1946 if (!driver_for_each_device
1947 (&(stmmacphy_driver.driver), NULL, (void *)priv,
1948 stmmac_associate_phy)) {
1949 pr_err("No PHY device is associated with this MAC!\n");
1954 priv->fix_mac_speed = plat_dat->fix_mac_speed;
1955 priv->bsp_priv = plat_dat->bsp_priv;
1957 pr_info("\t%s - (dev. name: %s - id: %d, IRQ #%d\n"
1958 "\tIO base addr: 0x%08x)\n", ndev->name, pdev->name,
1959 pdev->id, ndev->irq, (unsigned int)addr);
1961 /* MDIO bus Registration */
1962 pr_debug("\tMDIO bus (id: %d)...", priv->bus_id);
1963 ret = stmmac_mdio_register(ndev);
1966 pr_debug("registered!\n");
1970 platform_set_drvdata(pdev, NULL);
1971 release_mem_region(res->start, (res->end - res->start));
1981 * @pdev: platform device pointer
1982 * Description: this function resets the TX/RX processes, disables the MAC RX/TX
1983 * changes the link status, releases the DMA descriptor rings,
1984 * unregisters the MDIO bus and unmaps the allocated memory.
1986 static int stmmac_dvr_remove(struct platform_device *pdev)
1988 struct net_device *ndev = platform_get_drvdata(pdev);
1989 struct resource *res;
1991 pr_info("%s:\n\tremoving driver", __func__);
1993 stmmac_dma_stop_rx(ndev->base_addr);
1994 stmmac_dma_stop_tx(ndev->base_addr);
1996 stmmac_mac_disable_rx(ndev->base_addr);
1997 stmmac_mac_disable_tx(ndev->base_addr);
1999 netif_carrier_off(ndev);
2001 stmmac_mdio_unregister(ndev);
2003 platform_set_drvdata(pdev, NULL);
2004 unregister_netdev(ndev);
2006 iounmap((void *)ndev->base_addr);
2007 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2008 release_mem_region(res->start, (res->end - res->start));
2016 static int stmmac_suspend(struct platform_device *pdev, pm_message_t state)
2018 struct net_device *dev = platform_get_drvdata(pdev);
2019 struct stmmac_priv *priv = netdev_priv(dev);
2022 if (!dev || !netif_running(dev))
2025 spin_lock(&priv->lock);
2027 if (state.event == PM_EVENT_SUSPEND) {
2028 netif_device_detach(dev);
2029 netif_stop_queue(dev);
2031 phy_stop(priv->phydev);
2033 #ifdef CONFIG_STMMAC_TIMER
2034 priv->tm->timer_stop();
2035 if (likely(priv->tm->enable))
2038 napi_disable(&priv->napi);
2040 /* Stop TX/RX DMA */
2041 stmmac_dma_stop_tx(dev->base_addr);
2042 stmmac_dma_stop_rx(dev->base_addr);
2043 /* Clear the Rx/Tx descriptors */
2044 priv->mac_type->ops->init_rx_desc(priv->dma_rx,
2045 priv->dma_rx_size, dis_ic);
2046 priv->mac_type->ops->init_tx_desc(priv->dma_tx,
2049 stmmac_mac_disable_tx(dev->base_addr);
2051 if (device_may_wakeup(&(pdev->dev))) {
2052 /* Enable Power down mode by programming the PMT regs */
2053 if (priv->wolenabled == PMT_SUPPORTED)
2054 priv->mac_type->ops->pmt(dev->base_addr,
2057 stmmac_mac_disable_rx(dev->base_addr);
2061 /* Although this can appear slightly redundant it actually
2062 * makes fast the standby operation and guarantees the driver
2063 * working if hibernation is on media. */
2064 stmmac_release(dev);
2067 spin_unlock(&priv->lock);
2071 static int stmmac_resume(struct platform_device *pdev)
2073 struct net_device *dev = platform_get_drvdata(pdev);
2074 struct stmmac_priv *priv = netdev_priv(dev);
2075 unsigned long ioaddr = dev->base_addr;
2077 if (!netif_running(dev))
2080 spin_lock(&priv->lock);
2082 if (priv->shutdown) {
2083 /* Re-open the interface and re-init the MAC/DMA
2089 /* Power Down bit, into the PM register, is cleared
2090 * automatically as soon as a magic packet or a Wake-up frame
2091 * is received. Anyway, it's better to manually clear
2092 * this bit because it can generate problems while resuming
2093 * from another devices (e.g. serial console). */
2094 if (device_may_wakeup(&(pdev->dev)))
2095 if (priv->wolenabled == PMT_SUPPORTED)
2096 priv->mac_type->ops->pmt(dev->base_addr, 0);
2098 netif_device_attach(dev);
2100 /* Enable the MAC and DMA */
2101 stmmac_mac_enable_rx(ioaddr);
2102 stmmac_mac_enable_tx(ioaddr);
2103 stmmac_dma_start_tx(ioaddr);
2104 stmmac_dma_start_rx(ioaddr);
2106 #ifdef CONFIG_STMMAC_TIMER
2107 priv->tm->timer_start(tmrate);
2109 napi_enable(&priv->napi);
2112 phy_start(priv->phydev);
2114 netif_start_queue(dev);
2117 spin_unlock(&priv->lock);
2122 static struct platform_driver stmmac_driver = {
2124 .name = STMMAC_RESOURCE_NAME,
2126 .probe = stmmac_dvr_probe,
2127 .remove = stmmac_dvr_remove,
2129 .suspend = stmmac_suspend,
2130 .resume = stmmac_resume,
2136 * stmmac_init_module - Entry point for the driver
2137 * Description: This function is the entry point for the driver.
2139 static int __init stmmac_init_module(void)
2143 if (platform_driver_register(&stmmacphy_driver)) {
2144 pr_err("No PHY devices registered!\n");
2148 ret = platform_driver_register(&stmmac_driver);
2153 * stmmac_cleanup_module - Cleanup routine for the driver
2154 * Description: This function is the cleanup routine for the driver.
2156 static void __exit stmmac_cleanup_module(void)
2158 platform_driver_unregister(&stmmacphy_driver);
2159 platform_driver_unregister(&stmmac_driver);
2163 static int __init stmmac_cmdline_opt(char *str)
2169 while ((opt = strsep(&str, ",")) != NULL) {
2170 if (!strncmp(opt, "debug:", 6))
2171 strict_strtoul(opt + 6, 0, (unsigned long *)&debug);
2172 else if (!strncmp(opt, "phyaddr:", 8))
2173 strict_strtoul(opt + 8, 0, (unsigned long *)&phyaddr);
2174 else if (!strncmp(opt, "dma_txsize:", 11))
2175 strict_strtoul(opt + 11, 0,
2176 (unsigned long *)&dma_txsize);
2177 else if (!strncmp(opt, "dma_rxsize:", 11))
2178 strict_strtoul(opt + 11, 0,
2179 (unsigned long *)&dma_rxsize);
2180 else if (!strncmp(opt, "buf_sz:", 7))
2181 strict_strtoul(opt + 7, 0, (unsigned long *)&buf_sz);
2182 else if (!strncmp(opt, "tc:", 3))
2183 strict_strtoul(opt + 3, 0, (unsigned long *)&tc);
2184 else if (!strncmp(opt, "tx_coe:", 7))
2185 strict_strtoul(opt + 7, 0, (unsigned long *)&tx_coe);
2186 else if (!strncmp(opt, "watchdog:", 9))
2187 strict_strtoul(opt + 9, 0, (unsigned long *)&watchdog);
2188 else if (!strncmp(opt, "flow_ctrl:", 10))
2189 strict_strtoul(opt + 10, 0,
2190 (unsigned long *)&flow_ctrl);
2191 else if (!strncmp(opt, "pause:", 6))
2192 strict_strtoul(opt + 6, 0, (unsigned long *)&pause);
2193 #ifdef CONFIG_STMMAC_TIMER
2194 else if (!strncmp(opt, "tmrate:", 7))
2195 strict_strtoul(opt + 7, 0, (unsigned long *)&tmrate);
2201 __setup("stmmaceth=", stmmac_cmdline_opt);
2204 module_init(stmmac_init_module);
2205 module_exit(stmmac_cleanup_module);
2207 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet driver");
2208 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
2209 MODULE_LICENSE("GPL");