drivers/scsi/gvp11.c

   1 #include <linux/types.h>
   2 #include <linux/init.h>
   3 #include <linux/interrupt.h>
   4 #include <linux/mm.h>
   5 #include <linux/slab.h>
   6 #include <linux/spinlock.h>
   7 #include <linux/zorro.h>
   8
   9 #include <asm/page.h>
  10 #include <asm/pgtable.h>
  11 #include <asm/amigaints.h>
  12 #include <asm/amigahw.h>
  13
  14 #include "scsi.h"
  15 #include "wd33c93.h"
  16 #include "gvp11.h"
  17
  18
  19 #define CHECK_WD33C93
  20
  21 struct gvp11_hostdata {
  22         struct WD33C93_hostdata wh;
  23         struct gvp11_scsiregs *regs;
  24 };
  25
  26 static irqreturn_t gvp11_intr(int irq, void *data)
  27 {
  28         struct Scsi_Host *instance = data;
  29         struct gvp11_hostdata *hdata = shost_priv(instance);
  30         unsigned int status = hdata->regs->CNTR;
  31         unsigned long flags;
  32
  33         if (!(status & GVP11_DMAC_INT_PENDING))
  34                 return IRQ_NONE;
  35
  36         spin_lock_irqsave(instance->host_lock, flags);
  37         wd33c93_intr(instance);
  38         spin_unlock_irqrestore(instance->host_lock, flags);
  39         return IRQ_HANDLED;
  40 }
  41
  42 static int gvp11_xfer_mask = 0;
  43
  44 void gvp11_setup(char *str, int *ints)
  45 {
  46         gvp11_xfer_mask = ints[1];
  47 }
  48
  49 static int dma_setup(struct scsi_cmnd *cmd, int dir_in)
  50 {
  51         struct Scsi_Host *instance = cmd->device->host;
  52         struct gvp11_hostdata *hdata = shost_priv(instance);
  53         struct WD33C93_hostdata *wh = &hdata->wh;
  54         struct gvp11_scsiregs *regs = hdata->regs;
  55         unsigned short cntr = GVP11_DMAC_INT_ENABLE;
  56         unsigned long addr = virt_to_bus(cmd->SCp.ptr);
  57         int bank_mask;
  58         static int scsi_alloc_out_of_range = 0;
  59
  60         /* use bounce buffer if the physical address is bad */
  61         if (addr & wh->dma_xfer_mask) {
  62                 wh->dma_bounce_len = (cmd->SCp.this_residual + 511) & ~0x1ff;
  63
  64                 if (!scsi_alloc_out_of_range) {
  65                         wh->dma_bounce_buffer =
  66                                 kmalloc(wh->dma_bounce_len, GFP_KERNEL);
  67                         wh->dma_buffer_pool = BUF_SCSI_ALLOCED;
  68                 }
  69
  70                 if (scsi_alloc_out_of_range ||
  71                     !wh->dma_bounce_buffer) {
  72                         wh->dma_bounce_buffer =
  73                                 amiga_chip_alloc(wh->dma_bounce_len,
  74                                                  "GVP II SCSI Bounce Buffer");
  75
  76                         if (!wh->dma_bounce_buffer) {
  77                                 wh->dma_bounce_len = 0;
  78                                 return 1;
  79                         }
  80
  81                         wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
  82                 }
  83
  84                 /* check if the address of the bounce buffer is OK */
  85                 addr = virt_to_bus(wh->dma_bounce_buffer);
  86
  87                 if (addr & wh->dma_xfer_mask) {
  88                         /* fall back to Chip RAM if address out of range */
  89                         if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED) {
  90                                 kfree(wh->dma_bounce_buffer);
  91                                 scsi_alloc_out_of_range = 1;
  92                         } else {
  93                                 amiga_chip_free(wh->dma_bounce_buffer);
  94                         }
  95
  96                         wh->dma_bounce_buffer =
  97                                 amiga_chip_alloc(wh->dma_bounce_len,
  98                                                  "GVP II SCSI Bounce Buffer");
  99
 100                         if (!wh->dma_bounce_buffer) {
 101                                 wh->dma_bounce_len = 0;
 102                                 return 1;
 103                         }
 104
 105                         addr = virt_to_bus(wh->dma_bounce_buffer);
 106                         wh->dma_buffer_pool = BUF_CHIP_ALLOCED;
 107                 }
 108
 109                 if (!dir_in) {
 110                         /* copy to bounce buffer for a write */
 111                         memcpy(wh->dma_bounce_buffer, cmd->SCp.ptr,
 112                                cmd->SCp.this_residual);
 113                 }
 114         }
 115
 116         /* setup dma direction */
 117         if (!dir_in)
 118                 cntr |= GVP11_DMAC_DIR_WRITE;
 119
 120         wh->dma_dir = dir_in;
 121         regs->CNTR = cntr;
 122
 123         /* setup DMA *physical* address */
 124         regs->ACR = addr;
 125
 126         if (dir_in) {
 127                 /* invalidate any cache */
 128                 cache_clear(addr, cmd->SCp.this_residual);
 129         } else {
 130                 /* push any dirty cache */
 131                 cache_push(addr, cmd->SCp.this_residual);
 132         }
 133
 134         bank_mask = (~wh->dma_xfer_mask >> 18) & 0x01c0;
 135         if (bank_mask)
 136                 regs->BANK = bank_mask & (addr >> 18);
 137
 138         /* start DMA */
 139         regs->ST_DMA = 1;
 140
 141         /* return success */
 142         return 0;
 143 }
 144
 145 static void dma_stop(struct Scsi_Host *instance, struct scsi_cmnd *SCpnt,
 146                      int status)
 147 {
 148         struct gvp11_hostdata *hdata = shost_priv(instance);
 149         struct WD33C93_hostdata *wh = &hdata->wh;
 150         struct gvp11_scsiregs *regs = hdata->regs;
 151
 152         /* stop DMA */
 153         regs->SP_DMA = 1;
 154         /* remove write bit from CONTROL bits */
 155         regs->CNTR = GVP11_DMAC_INT_ENABLE;
 156
 157         /* copy from a bounce buffer, if necessary */
 158         if (status && wh->dma_bounce_buffer) {
 159                 if (wh->dma_dir && SCpnt)
 160                         memcpy(SCpnt->SCp.ptr, wh->dma_bounce_buffer,
 161                                SCpnt->SCp.this_residual);
 162
 163                 if (wh->dma_buffer_pool == BUF_SCSI_ALLOCED)
 164                         kfree(wh->dma_bounce_buffer);
 165                 else
 166                         amiga_chip_free(wh->dma_bounce_buffer);
 167
 168                 wh->dma_bounce_buffer = NULL;
 169                 wh->dma_bounce_len = 0;
 170         }
 171 }
 172
 173 static int gvp11_bus_reset(struct scsi_cmnd *cmd)
 174 {
 175         struct Scsi_Host *instance = cmd->device->host;
 176
 177         /* FIXME perform bus-specific reset */
 178
 179         /* FIXME 2: shouldn't we no-op this function (return
 180            FAILED), and fall back to host reset function,
 181            wd33c93_host_reset ? */
 182
 183         spin_lock_irq(instance->host_lock);
 184         wd33c93_host_reset(cmd);
 185         spin_unlock_irq(instance->host_lock);
 186
 187         return SUCCESS;
 188 }
 189
 190 static struct scsi_host_template gvp11_scsi_template = {
 191         .module                 = THIS_MODULE,
 192         .name                   = "GVP Series II SCSI",
 193         .proc_info              = wd33c93_proc_info,
 194         .proc_name              = "GVP11",
 195         .queuecommand           = wd33c93_queuecommand,
 196         .eh_abort_handler       = wd33c93_abort,
 197         .eh_bus_reset_handler   = gvp11_bus_reset,
 198         .eh_host_reset_handler  = wd33c93_host_reset,
 199         .can_queue              = CAN_QUEUE,
 200         .this_id                = 7,
 201         .sg_tablesize           = SG_ALL,
 202         .cmd_per_lun            = CMD_PER_LUN,
 203         .use_clustering         = DISABLE_CLUSTERING
 204 };
 205
 206 static int __devinit check_wd33c93(struct gvp11_scsiregs *regs)
 207 {
 208 #ifdef CHECK_WD33C93
 209         volatile unsigned char *sasr_3393, *scmd_3393;
 210         unsigned char save_sasr;
 211         unsigned char q, qq;
 212
 213         /*
 214          * These darn GVP boards are a problem - it can be tough to tell
 215          * whether or not they include a SCSI controller. This is the
 216          * ultimate Yet-Another-GVP-Detection-Hack in that it actually
 217          * probes for a WD33c93 chip: If we find one, it's extremely
 218          * likely that this card supports SCSI, regardless of Product_
 219          * Code, Board_Size, etc.
 220          */
 221
 222         /* Get pointers to the presumed register locations and save contents */
 223
 224         sasr_3393 = &regs->SASR;
 225         scmd_3393 = &regs->SCMD;
 226         save_sasr = *sasr_3393;
 227
 228         /* First test the AuxStatus Reg */
 229
 230         q = *sasr_3393; /* read it */
 231         if (q & 0x08)   /* bit 3 should always be clear */
 232                 return -ENODEV;
 233         *sasr_3393 = WD_AUXILIARY_STATUS;       /* setup indirect address */
 234         if (*sasr_3393 == WD_AUXILIARY_STATUS) {        /* shouldn't retain the write */
 235                 *sasr_3393 = save_sasr; /* Oops - restore this byte */
 236                 return -ENODEV;
 237         }
 238         if (*sasr_3393 != q) {  /* should still read the same */
 239                 *sasr_3393 = save_sasr; /* Oops - restore this byte */
 240                 return -ENODEV;
 241         }
 242         if (*scmd_3393 != q)    /* and so should the image at 0x1f */
 243                 return -ENODEV;
 244
 245         /*
 246          * Ok, we probably have a wd33c93, but let's check a few other places
 247          * for good measure. Make sure that this works for both 'A and 'B
 248          * chip versions.
 249          */
 250
 251         *sasr_3393 = WD_SCSI_STATUS;
 252         q = *scmd_3393;
 253         *sasr_3393 = WD_SCSI_STATUS;
 254         *scmd_3393 = ~q;
 255         *sasr_3393 = WD_SCSI_STATUS;
 256         qq = *scmd_3393;
 257         *sasr_3393 = WD_SCSI_STATUS;
 258         *scmd_3393 = q;
 259         if (qq != q)    /* should be read only */
 260                 return -ENODEV;
 261         *sasr_3393 = 0x1e;      /* this register is unimplemented */
 262         q = *scmd_3393;
 263         *sasr_3393 = 0x1e;
 264         *scmd_3393 = ~q;
 265         *sasr_3393 = 0x1e;
 266         qq = *scmd_3393;
 267         *sasr_3393 = 0x1e;
 268         *scmd_3393 = q;
 269         if (qq != q || qq != 0xff)      /* should be read only, all 1's */
 270                 return -ENODEV;
 271         *sasr_3393 = WD_TIMEOUT_PERIOD;
 272         q = *scmd_3393;
 273         *sasr_3393 = WD_TIMEOUT_PERIOD;
 274         *scmd_3393 = ~q;
 275         *sasr_3393 = WD_TIMEOUT_PERIOD;
 276         qq = *scmd_3393;
 277         *sasr_3393 = WD_TIMEOUT_PERIOD;
 278         *scmd_3393 = q;
 279         if (qq != (~q & 0xff))  /* should be read/write */
 280                 return -ENODEV;
 281 #endif /* CHECK_WD33C93 */
 282
 283         return 0;
 284 }
 285
 286 static int __devinit gvp11_probe(struct zorro_dev *z,
 287                                  const struct zorro_device_id *ent)
 288 {
 289         struct Scsi_Host *instance;
 290         unsigned long address;
 291         int error;
 292         unsigned int epc;
 293         unsigned int default_dma_xfer_mask;
 294         struct gvp11_hostdata *hdata;
 295         struct gvp11_scsiregs *regs;
 296         wd33c93_regs wdregs;
 297
 298         default_dma_xfer_mask = ent->driver_data;
 299
 300         /*
 301          * Rumors state that some GVP ram boards use the same product
 302          * code as the SCSI controllers. Therefore if the board-size
 303          * is not 64KB we asume it is a ram board and bail out.
 304          */
 305         if (zorro_resource_len(z) != 0x10000)
 306                 return -ENODEV;
 307
 308         address = z->resource.start;
 309         if (!request_mem_region(address, 256, "wd33c93"))
 310                 return -EBUSY;
 311
 312         regs = (struct gvp11_scsiregs *)(ZTWO_VADDR(address));
 313
 314         error = check_wd33c93(regs);
 315         if (error)
 316                 goto fail_check_or_alloc;
 317
 318         instance = scsi_host_alloc(&gvp11_scsi_template,
 319                                    sizeof(struct gvp11_hostdata));
 320         if (!instance) {
 321                 error = -ENOMEM;
 322                 goto fail_check_or_alloc;
 323         }
 324
 325         instance->irq = IRQ_AMIGA_PORTS;
 326         instance->unique_id = z->slotaddr;
 327
 328         regs->secret2 = 1;
 329         regs->secret1 = 0;
 330         regs->secret3 = 15;
 331         while (regs->CNTR & GVP11_DMAC_BUSY)
 332                 ;
 333         regs->CNTR = 0;
 334         regs->BANK = 0;
 335
 336         wdregs.SASR = &regs->SASR;
 337         wdregs.SCMD = &regs->SCMD;
 338
 339         hdata = shost_priv(instance);
 340         if (gvp11_xfer_mask)
 341                 hdata->wh.dma_xfer_mask = gvp11_xfer_mask;
 342         else
 343                 hdata->wh.dma_xfer_mask = default_dma_xfer_mask;
 344
 345         hdata->wh.no_sync = 0xff;
 346         hdata->wh.fast = 0;
 347         hdata->wh.dma_mode = CTRL_DMA;
 348         hdata->regs = regs;
 349
 350         /*
 351          * Check for 14MHz SCSI clock
 352          */
 353         epc = *(unsigned short *)(ZTWO_VADDR(address) + 0x8000);
 354         wd33c93_init(instance, wdregs, dma_setup, dma_stop,
 355                      (epc & GVP_SCSICLKMASK) ? WD33C93_FS_8_10
 356                                              : WD33C93_FS_12_15);
 357
 358         error = request_irq(IRQ_AMIGA_PORTS, gvp11_intr, IRQF_SHARED,
 359                             "GVP11 SCSI", instance);
 360         if (error)
 361                 goto fail_irq;
 362
 363         regs->CNTR = GVP11_DMAC_INT_ENABLE;
 364
 365         error = scsi_add_host(instance, NULL);
 366         if (error)
 367                 goto fail_host;
 368
 369         zorro_set_drvdata(z, instance);
 370         scsi_scan_host(instance);
 371         return 0;
 372
 373 fail_host:
 374         free_irq(IRQ_AMIGA_PORTS, instance);
 375 fail_irq:
 376         scsi_host_put(instance);
 377 fail_check_or_alloc:
 378         release_mem_region(address, 256);
 379         return error;
 380 }
 381
 382 static void __devexit gvp11_remove(struct zorro_dev *z)
 383 {
 384         struct Scsi_Host *instance = zorro_get_drvdata(z);
 385         struct gvp11_hostdata *hdata = shost_priv(instance);
 386
 387         hdata->regs->CNTR = 0;
 388         scsi_remove_host(instance);
 389         free_irq(IRQ_AMIGA_PORTS, instance);
 390         scsi_host_put(instance);
 391         release_mem_region(z->resource.start, 256);
 392 }
 393
 394         /*
 395          * This should (hopefully) be the correct way to identify
 396          * all the different GVP SCSI controllers (except for the
 397          * SERIES I though).
 398          */
 399
 400 static struct zorro_device_id gvp11_zorro_tbl[] __devinitdata = {
 401         { ZORRO_PROD_GVP_COMBO_030_R3_SCSI,     ~0x00ffffff },
 402         { ZORRO_PROD_GVP_SERIES_II,             ~0x00ffffff },
 403         { ZORRO_PROD_GVP_GFORCE_030_SCSI,       ~0x01ffffff },
 404         { ZORRO_PROD_GVP_A530_SCSI,             ~0x01ffffff },
 405         { ZORRO_PROD_GVP_COMBO_030_R4_SCSI,     ~0x01ffffff },
 406         { ZORRO_PROD_GVP_A1291,                 ~0x07ffffff },
 407         { ZORRO_PROD_GVP_GFORCE_040_SCSI_1,     ~0x07ffffff },
 408         { 0 }
 409 };
 410 MODULE_DEVICE_TABLE(zorro, gvp11_zorro_tbl);
 411
 412 static struct zorro_driver gvp11_driver = {
 413         .name           = "gvp11",
 414         .id_table       = gvp11_zorro_tbl,
 415         .probe          = gvp11_probe,
 416         .remove         = __devexit_p(gvp11_remove),
 417 };
 418
 419 static int __init gvp11_init(void)
 420 {
 421         return zorro_register_driver(&gvp11_driver);
 422 }
 423 module_init(gvp11_init);
 424
 425 static void __exit gvp11_exit(void)
 426 {
 427         zorro_unregister_driver(&gvp11_driver);
 428 }
 429 module_exit(gvp11_exit);
 430
 431 MODULE_DESCRIPTION("GVP Series II SCSI");
 432 MODULE_LICENSE("GPL");