drivers/spi/spi-s3c64xx.c

   1 /*
   2  * Copyright (C) 2009 Samsung Electronics Ltd.
   3  *      Jaswinder Singh <jassi.brar@samsung.com>
   4  *
   5  * This program is free software; you can redistribute it and/or modify
   6  * it under the terms of the GNU General Public License as published by
   7  * the Free Software Foundation; either version 2 of the License, or
   8  * (at your option) any later version.
   9  *
  10  * This program is distributed in the hope that it will be useful,
  11  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  12  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  13  * GNU General Public License for more details.
  14  *
  15  * You should have received a copy of the GNU General Public License
  16  * along with this program; if not, write to the Free Software
  17  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  18  */
  19
  20 #include <linux/init.h>
  21 #include <linux/module.h>
  22 #include <linux/workqueue.h>
  23 #include <linux/interrupt.h>
  24 #include <linux/delay.h>
  25 #include <linux/clk.h>
  26 #include <linux/dma-mapping.h>
  27 #include <linux/dmaengine.h>
  28 #include <linux/platform_device.h>
  29 #include <linux/pm_runtime.h>
  30 #include <linux/spi/spi.h>
  31 #include <linux/gpio.h>
  32 #include <linux/of.h>
  33 #include <linux/of_gpio.h>
  34
  35 #include <linux/platform_data/spi-s3c64xx.h>
  36
  37 #ifdef CONFIG_S3C_DMA
  38 #include <mach/dma.h>
  39 #endif
  40
  41 #define MAX_SPI_PORTS           3
  42
  43 /* Registers and bit-fields */
  44
  45 #define S3C64XX_SPI_CH_CFG              0x00
  46 #define S3C64XX_SPI_CLK_CFG             0x04
  47 #define S3C64XX_SPI_MODE_CFG    0x08
  48 #define S3C64XX_SPI_SLAVE_SEL   0x0C
  49 #define S3C64XX_SPI_INT_EN              0x10
  50 #define S3C64XX_SPI_STATUS              0x14
  51 #define S3C64XX_SPI_TX_DATA             0x18
  52 #define S3C64XX_SPI_RX_DATA             0x1C
  53 #define S3C64XX_SPI_PACKET_CNT  0x20
  54 #define S3C64XX_SPI_PENDING_CLR 0x24
  55 #define S3C64XX_SPI_SWAP_CFG    0x28
  56 #define S3C64XX_SPI_FB_CLK              0x2C
  57
  58 #define S3C64XX_SPI_CH_HS_EN            (1<<6)  /* High Speed Enable */
  59 #define S3C64XX_SPI_CH_SW_RST           (1<<5)
  60 #define S3C64XX_SPI_CH_SLAVE            (1<<4)
  61 #define S3C64XX_SPI_CPOL_L              (1<<3)
  62 #define S3C64XX_SPI_CPHA_B              (1<<2)
  63 #define S3C64XX_SPI_CH_RXCH_ON          (1<<1)
  64 #define S3C64XX_SPI_CH_TXCH_ON          (1<<0)
  65
  66 #define S3C64XX_SPI_CLKSEL_SRCMSK       (3<<9)
  67 #define S3C64XX_SPI_CLKSEL_SRCSHFT      9
  68 #define S3C64XX_SPI_ENCLK_ENABLE        (1<<8)
  69 #define S3C64XX_SPI_PSR_MASK            0xff
  70
  71 #define S3C64XX_SPI_MODE_CH_TSZ_BYTE            (0<<29)
  72 #define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD        (1<<29)
  73 #define S3C64XX_SPI_MODE_CH_TSZ_WORD            (2<<29)
  74 #define S3C64XX_SPI_MODE_CH_TSZ_MASK            (3<<29)
  75 #define S3C64XX_SPI_MODE_BUS_TSZ_BYTE           (0<<17)
  76 #define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD       (1<<17)
  77 #define S3C64XX_SPI_MODE_BUS_TSZ_WORD           (2<<17)
  78 #define S3C64XX_SPI_MODE_BUS_TSZ_MASK           (3<<17)
  79 #define S3C64XX_SPI_MODE_RXDMA_ON               (1<<2)
  80 #define S3C64XX_SPI_MODE_TXDMA_ON               (1<<1)
  81 #define S3C64XX_SPI_MODE_4BURST                 (1<<0)
  82
  83 #define S3C64XX_SPI_SLAVE_AUTO                  (1<<1)
  84 #define S3C64XX_SPI_SLAVE_SIG_INACT             (1<<0)
  85
  86 #define S3C64XX_SPI_INT_TRAILING_EN             (1<<6)
  87 #define S3C64XX_SPI_INT_RX_OVERRUN_EN           (1<<5)
  88 #define S3C64XX_SPI_INT_RX_UNDERRUN_EN          (1<<4)
  89 #define S3C64XX_SPI_INT_TX_OVERRUN_EN           (1<<3)
  90 #define S3C64XX_SPI_INT_TX_UNDERRUN_EN          (1<<2)
  91 #define S3C64XX_SPI_INT_RX_FIFORDY_EN           (1<<1)
  92 #define S3C64XX_SPI_INT_TX_FIFORDY_EN           (1<<0)
  93
  94 #define S3C64XX_SPI_ST_RX_OVERRUN_ERR           (1<<5)
  95 #define S3C64XX_SPI_ST_RX_UNDERRUN_ERR  (1<<4)
  96 #define S3C64XX_SPI_ST_TX_OVERRUN_ERR           (1<<3)
  97 #define S3C64XX_SPI_ST_TX_UNDERRUN_ERR  (1<<2)
  98 #define S3C64XX_SPI_ST_RX_FIFORDY               (1<<1)
  99 #define S3C64XX_SPI_ST_TX_FIFORDY               (1<<0)
 100
 101 #define S3C64XX_SPI_PACKET_CNT_EN               (1<<16)
 102
 103 #define S3C64XX_SPI_PND_TX_UNDERRUN_CLR         (1<<4)
 104 #define S3C64XX_SPI_PND_TX_OVERRUN_CLR          (1<<3)
 105 #define S3C64XX_SPI_PND_RX_UNDERRUN_CLR         (1<<2)
 106 #define S3C64XX_SPI_PND_RX_OVERRUN_CLR          (1<<1)
 107 #define S3C64XX_SPI_PND_TRAILING_CLR            (1<<0)
 108
 109 #define S3C64XX_SPI_SWAP_RX_HALF_WORD           (1<<7)
 110 #define S3C64XX_SPI_SWAP_RX_BYTE                (1<<6)
 111 #define S3C64XX_SPI_SWAP_RX_BIT                 (1<<5)
 112 #define S3C64XX_SPI_SWAP_RX_EN                  (1<<4)
 113 #define S3C64XX_SPI_SWAP_TX_HALF_WORD           (1<<3)
 114 #define S3C64XX_SPI_SWAP_TX_BYTE                (1<<2)
 115 #define S3C64XX_SPI_SWAP_TX_BIT                 (1<<1)
 116 #define S3C64XX_SPI_SWAP_TX_EN                  (1<<0)
 117
 118 #define S3C64XX_SPI_FBCLK_MSK           (3<<0)
 119
 120 #define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
 121 #define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
 122                                 (1 << (i)->port_conf->tx_st_done)) ? 1 : 0)
 123 #define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i))
 124 #define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \
 125                                         FIFO_LVL_MASK(i))
 126
 127 #define S3C64XX_SPI_MAX_TRAILCNT        0x3ff
 128 #define S3C64XX_SPI_TRAILCNT_OFF        19
 129
 130 #define S3C64XX_SPI_TRAILCNT            S3C64XX_SPI_MAX_TRAILCNT
 131
 132 #define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
 133
 134 #define RXBUSY    (1<<2)
 135 #define TXBUSY    (1<<3)
 136
 137 struct s3c64xx_spi_dma_data {
 138         struct dma_chan *ch;
 139         enum dma_transfer_direction direction;
 140         unsigned int dmach;
 141 };
 142
 143 /**
 144  * struct s3c64xx_spi_info - SPI Controller hardware info
 145  * @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register.
 146  * @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter.
 147  * @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter.
 148  * @high_speed: True, if the controller supports HIGH_SPEED_EN bit.
 149  * @clk_from_cmu: True, if the controller does not include a clock mux and
 150  *      prescaler unit.
 151  *
 152  * The Samsung s3c64xx SPI controller are used on various Samsung SoC's but
 153  * differ in some aspects such as the size of the fifo and spi bus clock
 154  * setup. Such differences are specified to the driver using this structure
 155  * which is provided as driver data to the driver.
 156  */
 157 struct s3c64xx_spi_port_config {
 158         int     fifo_lvl_mask[MAX_SPI_PORTS];
 159         int     rx_lvl_offset;
 160         int     tx_st_done;
 161         bool    high_speed;
 162         bool    clk_from_cmu;
 163 };
 164
 165 /**
 166  * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver.
 167  * @clk: Pointer to the spi clock.
 168  * @src_clk: Pointer to the clock used to generate SPI signals.
 169  * @master: Pointer to the SPI Protocol master.
 170  * @cntrlr_info: Platform specific data for the controller this driver manages.
 171  * @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint.
 172  * @queue: To log SPI xfer requests.
 173  * @lock: Controller specific lock.
 174  * @state: Set of FLAGS to indicate status.
 175  * @rx_dmach: Controller's DMA channel for Rx.
 176  * @tx_dmach: Controller's DMA channel for Tx.
 177  * @sfr_start: BUS address of SPI controller regs.
 178  * @regs: Pointer to ioremap'ed controller registers.
 179  * @irq: interrupt
 180  * @xfer_completion: To indicate completion of xfer task.
 181  * @cur_mode: Stores the active configuration of the controller.
 182  * @cur_bpw: Stores the active bits per word settings.
 183  * @cur_speed: Stores the active xfer clock speed.
 184  */
 185 struct s3c64xx_spi_driver_data {
 186         void __iomem                    *regs;
 187         struct clk                      *clk;
 188         struct clk                      *src_clk;
 189         struct platform_device          *pdev;
 190         struct spi_master               *master;
 191         struct s3c64xx_spi_info  *cntrlr_info;
 192         struct spi_device               *tgl_spi;
 193         struct list_head                queue;
 194         spinlock_t                      lock;
 195         unsigned long                   sfr_start;
 196         struct completion               xfer_completion;
 197         unsigned                        state;
 198         unsigned                        cur_mode, cur_bpw;
 199         unsigned                        cur_speed;
 200         struct s3c64xx_spi_dma_data     rx_dma;
 201         struct s3c64xx_spi_dma_data     tx_dma;
 202 #ifdef CONFIG_S3C_DMA
 203         struct samsung_dma_ops          *ops;
 204 #endif
 205         struct s3c64xx_spi_port_config  *port_conf;
 206         unsigned int                    port_id;
 207         unsigned long                   gpios[4];
 208 };
 209
 210 static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
 211 {
 212         void __iomem *regs = sdd->regs;
 213         unsigned long loops;
 214         u32 val;
 215
 216         writel(0, regs + S3C64XX_SPI_PACKET_CNT);
 217
 218         val = readl(regs + S3C64XX_SPI_CH_CFG);
 219         val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON);
 220         writel(val, regs + S3C64XX_SPI_CH_CFG);
 221
 222         val = readl(regs + S3C64XX_SPI_CH_CFG);
 223         val |= S3C64XX_SPI_CH_SW_RST;
 224         val &= ~S3C64XX_SPI_CH_HS_EN;
 225         writel(val, regs + S3C64XX_SPI_CH_CFG);
 226
 227         /* Flush TxFIFO*/
 228         loops = msecs_to_loops(1);
 229         do {
 230                 val = readl(regs + S3C64XX_SPI_STATUS);
 231         } while (TX_FIFO_LVL(val, sdd) && loops--);
 232
 233         if (loops == 0)
 234                 dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
 235
 236         /* Flush RxFIFO*/
 237         loops = msecs_to_loops(1);
 238         do {
 239                 val = readl(regs + S3C64XX_SPI_STATUS);
 240                 if (RX_FIFO_LVL(val, sdd))
 241                         readl(regs + S3C64XX_SPI_RX_DATA);
 242                 else
 243                         break;
 244         } while (loops--);
 245
 246         if (loops == 0)
 247                 dev_warn(&sdd->pdev->dev, "Timed out flushing RX FIFO\n");
 248
 249         val = readl(regs + S3C64XX_SPI_CH_CFG);
 250         val &= ~S3C64XX_SPI_CH_SW_RST;
 251         writel(val, regs + S3C64XX_SPI_CH_CFG);
 252
 253         val = readl(regs + S3C64XX_SPI_MODE_CFG);
 254         val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
 255         writel(val, regs + S3C64XX_SPI_MODE_CFG);
 256 }
 257
 258 static void s3c64xx_spi_dmacb(void *data)
 259 {
 260         struct s3c64xx_spi_driver_data *sdd;
 261         struct s3c64xx_spi_dma_data *dma = data;
 262         unsigned long flags;
 263
 264         if (dma->direction == DMA_DEV_TO_MEM)
 265                 sdd = container_of(data,
 266                         struct s3c64xx_spi_driver_data, rx_dma);
 267         else
 268                 sdd = container_of(data,
 269                         struct s3c64xx_spi_driver_data, tx_dma);
 270
 271         spin_lock_irqsave(&sdd->lock, flags);
 272
 273         if (dma->direction == DMA_DEV_TO_MEM) {
 274                 sdd->state &= ~RXBUSY;
 275                 if (!(sdd->state & TXBUSY))
 276                         complete(&sdd->xfer_completion);
 277         } else {
 278                 sdd->state &= ~TXBUSY;
 279                 if (!(sdd->state & RXBUSY))
 280                         complete(&sdd->xfer_completion);
 281         }
 282
 283         spin_unlock_irqrestore(&sdd->lock, flags);
 284 }
 285
 286 #ifdef CONFIG_S3C_DMA
 287 /* FIXME: remove this section once arch/arm/mach-s3c64xx uses dmaengine */
 288
 289 static struct s3c2410_dma_client s3c64xx_spi_dma_client = {
 290         .name = "samsung-spi-dma",
 291 };
 292
 293 static void prepare_dma(struct s3c64xx_spi_dma_data *dma,
 294                                         unsigned len, dma_addr_t buf)
 295 {
 296         struct s3c64xx_spi_driver_data *sdd;
 297         struct samsung_dma_prep info;
 298         struct samsung_dma_config config;
 299
 300         if (dma->direction == DMA_DEV_TO_MEM) {
 301                 sdd = container_of((void *)dma,
 302                         struct s3c64xx_spi_driver_data, rx_dma);
 303                 config.direction = sdd->rx_dma.direction;
 304                 config.fifo = sdd->sfr_start + S3C64XX_SPI_RX_DATA;
 305                 config.width = sdd->cur_bpw / 8;
 306                 sdd->ops->config((enum dma_ch)sdd->rx_dma.ch, &config);
 307         } else {
 308                 sdd = container_of((void *)dma,
 309                         struct s3c64xx_spi_driver_data, tx_dma);
 310                 config.direction =  sdd->tx_dma.direction;
 311                 config.fifo = sdd->sfr_start + S3C64XX_SPI_TX_DATA;
 312                 config.width = sdd->cur_bpw / 8;
 313                 sdd->ops->config((enum dma_ch)sdd->tx_dma.ch, &config);
 314         }
 315
 316         info.cap = DMA_SLAVE;
 317         info.len = len;
 318         info.fp = s3c64xx_spi_dmacb;
 319         info.fp_param = dma;
 320         info.direction = dma->direction;
 321         info.buf = buf;
 322
 323         sdd->ops->prepare((enum dma_ch)dma->ch, &info);
 324         sdd->ops->trigger((enum dma_ch)dma->ch);
 325 }
 326
 327 static int acquire_dma(struct s3c64xx_spi_driver_data *sdd)
 328 {
 329         struct samsung_dma_req req;
 330         struct device *dev = &sdd->pdev->dev;
 331
 332         sdd->ops = samsung_dma_get_ops();
 333
 334         req.cap = DMA_SLAVE;
 335         req.client = &s3c64xx_spi_dma_client;
 336
 337         sdd->rx_dma.ch = (void *)sdd->ops->request(sdd->rx_dma.dmach, &req, dev, "rx");
 338         sdd->tx_dma.ch = (void *)sdd->ops->request(sdd->tx_dma.dmach, &req, dev, "tx");
 339
 340         return 1;
 341 }
 342
 343 static int s3c64xx_spi_prepare_transfer(struct spi_master *spi)
 344 {
 345         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
 346
 347         /* Acquire DMA channels */
 348         while (!acquire_dma(sdd))
 349                 usleep_range(10000, 11000);
 350
 351         pm_runtime_get_sync(&sdd->pdev->dev);
 352
 353         return 0;
 354 }
 355
 356 static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi)
 357 {
 358         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
 359
 360         /* Free DMA channels */
 361         sdd->ops->release((enum dma_ch)sdd->rx_dma.ch, &s3c64xx_spi_dma_client);
 362         sdd->ops->release((enum dma_ch)sdd->tx_dma.ch, &s3c64xx_spi_dma_client);
 363
 364         pm_runtime_put(&sdd->pdev->dev);
 365
 366         return 0;
 367 }
 368
 369 static void s3c64xx_spi_dma_stop(struct s3c64xx_spi_driver_data *sdd,
 370                                  struct s3c64xx_spi_dma_data *dma)
 371 {
 372         sdd->ops->stop((enum dma_ch)dma->ch);
 373 }
 374 #else
 375
 376 static void prepare_dma(struct s3c64xx_spi_dma_data *dma,
 377                                         unsigned len, dma_addr_t buf)
 378 {
 379         struct s3c64xx_spi_driver_data *sdd;
 380         struct dma_slave_config config;
 381         struct scatterlist sg;
 382         struct dma_async_tx_descriptor *desc;
 383
 384         if (dma->direction == DMA_DEV_TO_MEM) {
 385                 sdd = container_of((void *)dma,
 386                         struct s3c64xx_spi_driver_data, rx_dma);
 387                 config.direction = dma->direction;
 388                 config.src_addr = sdd->sfr_start + S3C64XX_SPI_RX_DATA;
 389                 config.src_addr_width = sdd->cur_bpw / 8;
 390                 config.src_maxburst = 1;
 391                 dmaengine_slave_config(dma->ch, &config);
 392         } else {
 393                 sdd = container_of((void *)dma,
 394                         struct s3c64xx_spi_driver_data, tx_dma);
 395                 config.direction = dma->direction;
 396                 config.dst_addr = sdd->sfr_start + S3C64XX_SPI_TX_DATA;
 397                 config.dst_addr_width = sdd->cur_bpw / 8;
 398                 config.dst_maxburst = 1;
 399                 dmaengine_slave_config(dma->ch, &config);
 400         }
 401
 402         sg_init_table(&sg, 1);
 403         sg_dma_len(&sg) = len;
 404         sg_set_page(&sg, pfn_to_page(PFN_DOWN(buf)),
 405                     len, offset_in_page(buf));
 406         sg_dma_address(&sg) = buf;
 407
 408         desc = dmaengine_prep_slave_sg(dma->ch,
 409                 &sg, 1, dma->direction, DMA_PREP_INTERRUPT);
 410
 411         desc->callback = s3c64xx_spi_dmacb;
 412         desc->callback_param = dma;
 413
 414         dmaengine_submit(desc);
 415         dma_async_issue_pending(dma->ch);
 416 }
 417
 418 static int s3c64xx_spi_prepare_transfer(struct spi_master *spi)
 419 {
 420         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
 421         dma_filter_fn filter = sdd->cntrlr_info->filter;
 422         struct device *dev = &sdd->pdev->dev;
 423         dma_cap_mask_t mask;
 424         int ret;
 425
 426         dma_cap_zero(mask);
 427         dma_cap_set(DMA_SLAVE, mask);
 428
 429         /* Acquire DMA channels */
 430         sdd->rx_dma.ch = dma_request_slave_channel_compat(mask, filter,
 431                                 (void*)sdd->rx_dma.dmach, dev, "rx");
 432         if (!sdd->rx_dma.ch) {
 433                 dev_err(dev, "Failed to get RX DMA channel\n");
 434                 ret = -EBUSY;
 435                 goto out;
 436         }
 437
 438         sdd->tx_dma.ch = dma_request_slave_channel_compat(mask, filter,
 439                                 (void*)sdd->tx_dma.dmach, dev, "tx");
 440         if (!sdd->tx_dma.ch) {
 441                 dev_err(dev, "Failed to get TX DMA channel\n");
 442                 ret = -EBUSY;
 443                 goto out_rx;
 444         }
 445
 446         ret = pm_runtime_get_sync(&sdd->pdev->dev);
 447         if (ret != 0) {
 448                 dev_err(dev, "Failed to enable device: %d\n", ret);
 449                 goto out_tx;
 450         }
 451
 452         return 0;
 453
 454 out_tx:
 455         dma_release_channel(sdd->tx_dma.ch);
 456 out_rx:
 457         dma_release_channel(sdd->rx_dma.ch);
 458 out:
 459         return ret;
 460 }
 461
 462 static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi)
 463 {
 464         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
 465
 466         /* Free DMA channels */
 467         dma_release_channel(sdd->rx_dma.ch);
 468         dma_release_channel(sdd->tx_dma.ch);
 469
 470         pm_runtime_put(&sdd->pdev->dev);
 471         return 0;
 472 }
 473
 474 static void s3c64xx_spi_dma_stop(struct s3c64xx_spi_driver_data *sdd,
 475                                  struct s3c64xx_spi_dma_data *dma)
 476 {
 477         dmaengine_terminate_all(dma->ch);
 478 }
 479 #endif
 480
 481 static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
 482                                 struct spi_device *spi,
 483                                 struct spi_transfer *xfer, int dma_mode)
 484 {
 485         void __iomem *regs = sdd->regs;
 486         u32 modecfg, chcfg;
 487
 488         modecfg = readl(regs + S3C64XX_SPI_MODE_CFG);
 489         modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
 490
 491         chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
 492         chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
 493
 494         if (dma_mode) {
 495                 chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
 496         } else {
 497                 /* Always shift in data in FIFO, even if xfer is Tx only,
 498                  * this helps setting PCKT_CNT value for generating clocks
 499                  * as exactly needed.
 500                  */
 501                 chcfg |= S3C64XX_SPI_CH_RXCH_ON;
 502                 writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
 503                                         | S3C64XX_SPI_PACKET_CNT_EN,
 504                                         regs + S3C64XX_SPI_PACKET_CNT);
 505         }
 506
 507         if (xfer->tx_buf != NULL) {
 508                 sdd->state |= TXBUSY;
 509                 chcfg |= S3C64XX_SPI_CH_TXCH_ON;
 510                 if (dma_mode) {
 511                         modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
 512                         prepare_dma(&sdd->tx_dma, xfer->len, xfer->tx_dma);
 513                 } else {
 514                         switch (sdd->cur_bpw) {
 515                         case 32:
 516                                 iowrite32_rep(regs + S3C64XX_SPI_TX_DATA,
 517                                         xfer->tx_buf, xfer->len / 4);
 518                                 break;
 519                         case 16:
 520                                 iowrite16_rep(regs + S3C64XX_SPI_TX_DATA,
 521                                         xfer->tx_buf, xfer->len / 2);
 522                                 break;
 523                         default:
 524                                 iowrite8_rep(regs + S3C64XX_SPI_TX_DATA,
 525                                         xfer->tx_buf, xfer->len);
 526                                 break;
 527                         }
 528                 }
 529         }
 530
 531         if (xfer->rx_buf != NULL) {
 532                 sdd->state |= RXBUSY;
 533
 534                 if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL
 535                                         && !(sdd->cur_mode & SPI_CPHA))
 536                         chcfg |= S3C64XX_SPI_CH_HS_EN;
 537
 538                 if (dma_mode) {
 539                         modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
 540                         chcfg |= S3C64XX_SPI_CH_RXCH_ON;
 541                         writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
 542                                         | S3C64XX_SPI_PACKET_CNT_EN,
 543                                         regs + S3C64XX_SPI_PACKET_CNT);
 544                         prepare_dma(&sdd->rx_dma, xfer->len, xfer->rx_dma);
 545                 }
 546         }
 547
 548         writel(modecfg, regs + S3C64XX_SPI_MODE_CFG);
 549         writel(chcfg, regs + S3C64XX_SPI_CH_CFG);
 550 }
 551
 552 static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
 553                                                 struct spi_device *spi)
 554 {
 555         struct s3c64xx_spi_csinfo *cs;
 556
 557         if (sdd->tgl_spi != NULL) { /* If last device toggled after mssg */
 558                 if (sdd->tgl_spi != spi) { /* if last mssg on diff device */
 559                         /* Deselect the last toggled device */
 560                         cs = sdd->tgl_spi->controller_data;
 561                         gpio_set_value(cs->line,
 562                                 spi->mode & SPI_CS_HIGH ? 0 : 1);
 563                 }
 564                 sdd->tgl_spi = NULL;
 565         }
 566
 567         cs = spi->controller_data;
 568         gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
 569 }
 570
 571 static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
 572                                 struct spi_transfer *xfer, int dma_mode)
 573 {
 574         void __iomem *regs = sdd->regs;
 575         unsigned long val;
 576         int ms;
 577
 578         /* millisecs to xfer 'len' bytes @ 'cur_speed' */
 579         ms = xfer->len * 8 * 1000 / sdd->cur_speed;
 580         ms += 10; /* some tolerance */
 581
 582         if (dma_mode) {
 583                 val = msecs_to_jiffies(ms) + 10;
 584                 val = wait_for_completion_timeout(&sdd->xfer_completion, val);
 585         } else {
 586                 u32 status;
 587                 val = msecs_to_loops(ms);
 588                 do {
 589                         status = readl(regs + S3C64XX_SPI_STATUS);
 590                 } while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
 591         }
 592
 593         if (!val)
 594                 return -EIO;
 595
 596         if (dma_mode) {
 597                 u32 status;
 598
 599                 /*
 600                  * DmaTx returns after simply writing data in the FIFO,
 601                  * w/o waiting for real transmission on the bus to finish.
 602                  * DmaRx returns only after Dma read data from FIFO which
 603                  * needs bus transmission to finish, so we don't worry if
 604                  * Xfer involved Rx(with or without Tx).
 605                  */
 606                 if (xfer->rx_buf == NULL) {
 607                         val = msecs_to_loops(10);
 608                         status = readl(regs + S3C64XX_SPI_STATUS);
 609                         while ((TX_FIFO_LVL(status, sdd)
 610                                 || !S3C64XX_SPI_ST_TX_DONE(status, sdd))
 611                                         && --val) {
 612                                 cpu_relax();
 613                                 status = readl(regs + S3C64XX_SPI_STATUS);
 614                         }
 615
 616                         if (!val)
 617                                 return -EIO;
 618                 }
 619         } else {
 620                 /* If it was only Tx */
 621                 if (xfer->rx_buf == NULL) {
 622                         sdd->state &= ~TXBUSY;
 623                         return 0;
 624                 }
 625
 626                 switch (sdd->cur_bpw) {
 627                 case 32:
 628                         ioread32_rep(regs + S3C64XX_SPI_RX_DATA,
 629                                 xfer->rx_buf, xfer->len / 4);
 630                         break;
 631                 case 16:
 632                         ioread16_rep(regs + S3C64XX_SPI_RX_DATA,
 633                                 xfer->rx_buf, xfer->len / 2);
 634                         break;
 635                 default:
 636                         ioread8_rep(regs + S3C64XX_SPI_RX_DATA,
 637                                 xfer->rx_buf, xfer->len);
 638                         break;
 639                 }
 640                 sdd->state &= ~RXBUSY;
 641         }
 642
 643         return 0;
 644 }
 645
 646 static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
 647                                                 struct spi_device *spi)
 648 {
 649         struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 650
 651         if (sdd->tgl_spi == spi)
 652                 sdd->tgl_spi = NULL;
 653
 654         gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
 655 }
 656
 657 static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
 658 {
 659         void __iomem *regs = sdd->regs;
 660         u32 val;
 661
 662         /* Disable Clock */
 663         if (sdd->port_conf->clk_from_cmu) {
 664                 clk_disable_unprepare(sdd->src_clk);
 665         } else {
 666                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 667                 val &= ~S3C64XX_SPI_ENCLK_ENABLE;
 668                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 669         }
 670
 671         /* Set Polarity and Phase */
 672         val = readl(regs + S3C64XX_SPI_CH_CFG);
 673         val &= ~(S3C64XX_SPI_CH_SLAVE |
 674                         S3C64XX_SPI_CPOL_L |
 675                         S3C64XX_SPI_CPHA_B);
 676
 677         if (sdd->cur_mode & SPI_CPOL)
 678                 val |= S3C64XX_SPI_CPOL_L;
 679
 680         if (sdd->cur_mode & SPI_CPHA)
 681                 val |= S3C64XX_SPI_CPHA_B;
 682
 683         writel(val, regs + S3C64XX_SPI_CH_CFG);
 684
 685         /* Set Channel & DMA Mode */
 686         val = readl(regs + S3C64XX_SPI_MODE_CFG);
 687         val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK
 688                         | S3C64XX_SPI_MODE_CH_TSZ_MASK);
 689
 690         switch (sdd->cur_bpw) {
 691         case 32:
 692                 val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
 693                 val |= S3C64XX_SPI_MODE_CH_TSZ_WORD;
 694                 break;
 695         case 16:
 696                 val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
 697                 val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD;
 698                 break;
 699         default:
 700                 val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
 701                 val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE;
 702                 break;
 703         }
 704
 705         writel(val, regs + S3C64XX_SPI_MODE_CFG);
 706
 707         if (sdd->port_conf->clk_from_cmu) {
 708                 /* Configure Clock */
 709                 /* There is half-multiplier before the SPI */
 710                 clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
 711                 /* Enable Clock */
 712                 clk_prepare_enable(sdd->src_clk);
 713         } else {
 714                 /* Configure Clock */
 715                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 716                 val &= ~S3C64XX_SPI_PSR_MASK;
 717                 val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
 718                                 & S3C64XX_SPI_PSR_MASK);
 719                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 720
 721                 /* Enable Clock */
 722                 val = readl(regs + S3C64XX_SPI_CLK_CFG);
 723                 val |= S3C64XX_SPI_ENCLK_ENABLE;
 724                 writel(val, regs + S3C64XX_SPI_CLK_CFG);
 725         }
 726 }
 727
 728 #define XFER_DMAADDR_INVALID DMA_BIT_MASK(32)
 729
 730 static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd,
 731                                                 struct spi_message *msg)
 732 {
 733         struct device *dev = &sdd->pdev->dev;
 734         struct spi_transfer *xfer;
 735
 736         if (msg->is_dma_mapped)
 737                 return 0;
 738
 739         /* First mark all xfer unmapped */
 740         list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 741                 xfer->rx_dma = XFER_DMAADDR_INVALID;
 742                 xfer->tx_dma = XFER_DMAADDR_INVALID;
 743         }
 744
 745         /* Map until end or first fail */
 746         list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 747
 748                 if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
 749                         continue;
 750
 751                 if (xfer->tx_buf != NULL) {
 752                         xfer->tx_dma = dma_map_single(dev,
 753                                         (void *)xfer->tx_buf, xfer->len,
 754                                         DMA_TO_DEVICE);
 755                         if (dma_mapping_error(dev, xfer->tx_dma)) {
 756                                 dev_err(dev, "dma_map_single Tx failed\n");
 757                                 xfer->tx_dma = XFER_DMAADDR_INVALID;
 758                                 return -ENOMEM;
 759                         }
 760                 }
 761
 762                 if (xfer->rx_buf != NULL) {
 763                         xfer->rx_dma = dma_map_single(dev, xfer->rx_buf,
 764                                                 xfer->len, DMA_FROM_DEVICE);
 765                         if (dma_mapping_error(dev, xfer->rx_dma)) {
 766                                 dev_err(dev, "dma_map_single Rx failed\n");
 767                                 dma_unmap_single(dev, xfer->tx_dma,
 768                                                 xfer->len, DMA_TO_DEVICE);
 769                                 xfer->tx_dma = XFER_DMAADDR_INVALID;
 770                                 xfer->rx_dma = XFER_DMAADDR_INVALID;
 771                                 return -ENOMEM;
 772                         }
 773                 }
 774         }
 775
 776         return 0;
 777 }
 778
 779 static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd,
 780                                                 struct spi_message *msg)
 781 {
 782         struct device *dev = &sdd->pdev->dev;
 783         struct spi_transfer *xfer;
 784
 785         if (msg->is_dma_mapped)
 786                 return;
 787
 788         list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 789
 790                 if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1))
 791                         continue;
 792
 793                 if (xfer->rx_buf != NULL
 794                                 && xfer->rx_dma != XFER_DMAADDR_INVALID)
 795                         dma_unmap_single(dev, xfer->rx_dma,
 796                                                 xfer->len, DMA_FROM_DEVICE);
 797
 798                 if (xfer->tx_buf != NULL
 799                                 && xfer->tx_dma != XFER_DMAADDR_INVALID)
 800                         dma_unmap_single(dev, xfer->tx_dma,
 801                                                 xfer->len, DMA_TO_DEVICE);
 802         }
 803 }
 804
 805 static int s3c64xx_spi_transfer_one_message(struct spi_master *master,
 806                                             struct spi_message *msg)
 807 {
 808         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
 809         struct spi_device *spi = msg->spi;
 810         struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 811         struct spi_transfer *xfer;
 812         int status = 0, cs_toggle = 0;
 813         u32 speed;
 814         u8 bpw;
 815
 816         /* If Master's(controller) state differs from that needed by Slave */
 817         if (sdd->cur_speed != spi->max_speed_hz
 818                         || sdd->cur_mode != spi->mode
 819                         || sdd->cur_bpw != spi->bits_per_word) {
 820                 sdd->cur_bpw = spi->bits_per_word;
 821                 sdd->cur_speed = spi->max_speed_hz;
 822                 sdd->cur_mode = spi->mode;
 823                 s3c64xx_spi_config(sdd);
 824         }
 825
 826         /* Map all the transfers if needed */
 827         if (s3c64xx_spi_map_mssg(sdd, msg)) {
 828                 dev_err(&spi->dev,
 829                         "Xfer: Unable to map message buffers!\n");
 830                 status = -ENOMEM;
 831                 goto out;
 832         }
 833
 834         /* Configure feedback delay */
 835         writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK);
 836
 837         list_for_each_entry(xfer, &msg->transfers, transfer_list) {
 838
 839                 unsigned long flags;
 840                 int use_dma;
 841
 842                 INIT_COMPLETION(sdd->xfer_completion);
 843
 844                 /* Only BPW and Speed may change across transfers */
 845                 bpw = xfer->bits_per_word;
 846                 speed = xfer->speed_hz ? : spi->max_speed_hz;
 847
 848                 if (xfer->len % (bpw / 8)) {
 849                         dev_err(&spi->dev,
 850                                 "Xfer length(%u) not a multiple of word size(%u)\n",
 851                                 xfer->len, bpw / 8);
 852                         status = -EIO;
 853                         goto out;
 854                 }
 855
 856                 if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
 857                         sdd->cur_bpw = bpw;
 858                         sdd->cur_speed = speed;
 859                         s3c64xx_spi_config(sdd);
 860                 }
 861
 862                 /* Polling method for xfers not bigger than FIFO capacity */
 863                 use_dma = 0;
 864                 if (sdd->rx_dma.ch && sdd->tx_dma.ch &&
 865                     (xfer->len > ((FIFO_LVL_MASK(sdd) >> 1) + 1)))
 866                         use_dma = 1;
 867
 868                 spin_lock_irqsave(&sdd->lock, flags);
 869
 870                 /* Pending only which is to be done */
 871                 sdd->state &= ~RXBUSY;
 872                 sdd->state &= ~TXBUSY;
 873
 874                 enable_datapath(sdd, spi, xfer, use_dma);
 875
 876                 /* Slave Select */
 877                 enable_cs(sdd, spi);
 878
 879                 /* Start the signals */
 880                 writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 881
 882                 spin_unlock_irqrestore(&sdd->lock, flags);
 883
 884                 status = wait_for_xfer(sdd, xfer, use_dma);
 885
 886                 /* Quiese the signals */
 887                 writel(S3C64XX_SPI_SLAVE_SIG_INACT,
 888                        sdd->regs + S3C64XX_SPI_SLAVE_SEL);
 889
 890                 if (status) {
 891                         dev_err(&spi->dev, "I/O Error: rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
 892                                 xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0,
 893                                 (sdd->state & RXBUSY) ? 'f' : 'p',
 894                                 (sdd->state & TXBUSY) ? 'f' : 'p',
 895                                 xfer->len);
 896
 897                         if (use_dma) {
 898                                 if (xfer->tx_buf != NULL
 899                                                 && (sdd->state & TXBUSY))
 900                                         s3c64xx_spi_dma_stop(sdd, &sdd->tx_dma);
 901                                 if (xfer->rx_buf != NULL
 902                                                 && (sdd->state & RXBUSY))
 903                                         s3c64xx_spi_dma_stop(sdd, &sdd->rx_dma);
 904                         }
 905
 906                         goto out;
 907                 }
 908
 909                 if (xfer->delay_usecs)
 910                         udelay(xfer->delay_usecs);
 911
 912                 if (xfer->cs_change) {
 913                         /* Hint that the next mssg is gonna be
 914                            for the same device */
 915                         if (list_is_last(&xfer->transfer_list,
 916                                                 &msg->transfers))
 917                                 cs_toggle = 1;
 918                 }
 919
 920                 msg->actual_length += xfer->len;
 921
 922                 flush_fifo(sdd);
 923         }
 924
 925 out:
 926         if (!cs_toggle || status)
 927                 disable_cs(sdd, spi);
 928         else
 929                 sdd->tgl_spi = spi;
 930
 931         s3c64xx_spi_unmap_mssg(sdd, msg);
 932
 933         msg->status = status;
 934
 935         spi_finalize_current_message(master);
 936
 937         return 0;
 938 }
 939
 940 static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata(
 941                                 struct spi_device *spi)
 942 {
 943         struct s3c64xx_spi_csinfo *cs;
 944         struct device_node *slave_np, *data_np = NULL;
 945         u32 fb_delay = 0;
 946
 947         slave_np = spi->dev.of_node;
 948         if (!slave_np) {
 949                 dev_err(&spi->dev, "device node not found\n");
 950                 return ERR_PTR(-EINVAL);
 951         }
 952
 953         data_np = of_get_child_by_name(slave_np, "controller-data");
 954         if (!data_np) {
 955                 dev_err(&spi->dev, "child node 'controller-data' not found\n");
 956                 return ERR_PTR(-EINVAL);
 957         }
 958
 959         cs = kzalloc(sizeof(*cs), GFP_KERNEL);
 960         if (!cs) {
 961                 dev_err(&spi->dev, "could not allocate memory for controller data\n");
 962                 of_node_put(data_np);
 963                 return ERR_PTR(-ENOMEM);
 964         }
 965
 966         cs->line = of_get_named_gpio(data_np, "cs-gpio", 0);
 967         if (!gpio_is_valid(cs->line)) {
 968                 dev_err(&spi->dev, "chip select gpio is not specified or invalid\n");
 969                 kfree(cs);
 970                 of_node_put(data_np);
 971                 return ERR_PTR(-EINVAL);
 972         }
 973
 974         of_property_read_u32(data_np, "samsung,spi-feedback-delay", &fb_delay);
 975         cs->fb_delay = fb_delay;
 976         of_node_put(data_np);
 977         return cs;
 978 }
 979
 980 /*
 981  * Here we only check the validity of requested configuration
 982  * and save the configuration in a local data-structure.
 983  * The controller is actually configured only just before we
 984  * get a message to transfer.
 985  */
 986 static int s3c64xx_spi_setup(struct spi_device *spi)
 987 {
 988         struct s3c64xx_spi_csinfo *cs = spi->controller_data;
 989         struct s3c64xx_spi_driver_data *sdd;
 990         struct s3c64xx_spi_info *sci;
 991         struct spi_message *msg;
 992         unsigned long flags;
 993         int err;
 994
 995         sdd = spi_master_get_devdata(spi->master);
 996         if (!cs && spi->dev.of_node) {
 997                 cs = s3c64xx_get_slave_ctrldata(spi);
 998                 spi->controller_data = cs;
 999         }
1000
1001         if (IS_ERR_OR_NULL(cs)) {
1002                 dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
1003                 return -ENODEV;
1004         }
1005
1006         if (!spi_get_ctldata(spi)) {
1007                 err = gpio_request_one(cs->line, GPIOF_OUT_INIT_HIGH,
1008                                        dev_name(&spi->dev));
1009                 if (err) {
1010                         dev_err(&spi->dev,
1011                                 "Failed to get /CS gpio [%d]: %d\n",
1012                                 cs->line, err);
1013                         goto err_gpio_req;
1014                 }
1015                 spi_set_ctldata(spi, cs);
1016         }
1017
1018         sci = sdd->cntrlr_info;
1019
1020         spin_lock_irqsave(&sdd->lock, flags);
1021
1022         list_for_each_entry(msg, &sdd->queue, queue) {
1023                 /* Is some mssg is already queued for this device */
1024                 if (msg->spi == spi) {
1025                         dev_err(&spi->dev,
1026                                 "setup: attempt while mssg in queue!\n");
1027                         spin_unlock_irqrestore(&sdd->lock, flags);
1028                         err = -EBUSY;
1029                         goto err_msgq;
1030                 }
1031         }
1032
1033         spin_unlock_irqrestore(&sdd->lock, flags);
1034
1035         pm_runtime_get_sync(&sdd->pdev->dev);
1036
1037         /* Check if we can provide the requested rate */
1038         if (!sdd->port_conf->clk_from_cmu) {
1039                 u32 psr, speed;
1040
1041                 /* Max possible */
1042                 speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1);
1043
1044                 if (spi->max_speed_hz > speed)
1045                         spi->max_speed_hz = speed;
1046
1047                 psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
1048                 psr &= S3C64XX_SPI_PSR_MASK;
1049                 if (psr == S3C64XX_SPI_PSR_MASK)
1050                         psr--;
1051
1052                 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
1053                 if (spi->max_speed_hz < speed) {
1054                         if (psr+1 < S3C64XX_SPI_PSR_MASK) {
1055                                 psr++;
1056                         } else {
1057                                 err = -EINVAL;
1058                                 goto setup_exit;
1059                         }
1060                 }
1061
1062                 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
1063                 if (spi->max_speed_hz >= speed) {
1064                         spi->max_speed_hz = speed;
1065                 } else {
1066                         dev_err(&spi->dev, "Can't set %dHz transfer speed\n",
1067                                 spi->max_speed_hz);
1068                         err = -EINVAL;
1069                         goto setup_exit;
1070                 }
1071         }
1072
1073         pm_runtime_put(&sdd->pdev->dev);
1074         disable_cs(sdd, spi);
1075         return 0;
1076
1077 setup_exit:
1078         /* setup() returns with device de-selected */
1079         disable_cs(sdd, spi);
1080
1081 err_msgq:
1082         gpio_free(cs->line);
1083         spi_set_ctldata(spi, NULL);
1084
1085 err_gpio_req:
1086         if (spi->dev.of_node)
1087                 kfree(cs);
1088
1089         return err;
1090 }
1091
1092 static void s3c64xx_spi_cleanup(struct spi_device *spi)
1093 {
1094         struct s3c64xx_spi_csinfo *cs = spi_get_ctldata(spi);
1095
1096         if (cs) {
1097                 gpio_free(cs->line);
1098                 if (spi->dev.of_node)
1099                         kfree(cs);
1100         }
1101         spi_set_ctldata(spi, NULL);
1102 }
1103
1104 static irqreturn_t s3c64xx_spi_irq(int irq, void *data)
1105 {
1106         struct s3c64xx_spi_driver_data *sdd = data;
1107         struct spi_master *spi = sdd->master;
1108         unsigned int val, clr = 0;
1109
1110         val = readl(sdd->regs + S3C64XX_SPI_STATUS);
1111
1112         if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) {
1113                 clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR;
1114                 dev_err(&spi->dev, "RX overrun\n");
1115         }
1116         if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) {
1117                 clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR;
1118                 dev_err(&spi->dev, "RX underrun\n");
1119         }
1120         if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) {
1121                 clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR;
1122                 dev_err(&spi->dev, "TX overrun\n");
1123         }
1124         if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) {
1125                 clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
1126                 dev_err(&spi->dev, "TX underrun\n");
1127         }
1128
1129         /* Clear the pending irq by setting and then clearing it */
1130         writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
1131         writel(0, sdd->regs + S3C64XX_SPI_PENDING_CLR);
1132
1133         return IRQ_HANDLED;
1134 }
1135
1136 static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
1137 {
1138         struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
1139         void __iomem *regs = sdd->regs;
1140         unsigned int val;
1141
1142         sdd->cur_speed = 0;
1143
1144         writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
1145
1146         /* Disable Interrupts - we use Polling if not DMA mode */
1147         writel(0, regs + S3C64XX_SPI_INT_EN);
1148
1149         if (!sdd->port_conf->clk_from_cmu)
1150                 writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
1151                                 regs + S3C64XX_SPI_CLK_CFG);
1152         writel(0, regs + S3C64XX_SPI_MODE_CFG);
1153         writel(0, regs + S3C64XX_SPI_PACKET_CNT);
1154
1155         /* Clear any irq pending bits, should set and clear the bits */
1156         val = S3C64XX_SPI_PND_RX_OVERRUN_CLR |
1157                 S3C64XX_SPI_PND_RX_UNDERRUN_CLR |
1158                 S3C64XX_SPI_PND_TX_OVERRUN_CLR |
1159                 S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
1160         writel(val, regs + S3C64XX_SPI_PENDING_CLR);
1161         writel(0, regs + S3C64XX_SPI_PENDING_CLR);
1162
1163         writel(0, regs + S3C64XX_SPI_SWAP_CFG);
1164
1165         val = readl(regs + S3C64XX_SPI_MODE_CFG);
1166         val &= ~S3C64XX_SPI_MODE_4BURST;
1167         val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
1168         val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
1169         writel(val, regs + S3C64XX_SPI_MODE_CFG);
1170
1171         flush_fifo(sdd);
1172 }
1173
1174 #ifdef CONFIG_OF
1175 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
1176 {
1177         struct s3c64xx_spi_info *sci;
1178         u32 temp;
1179
1180         sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL);
1181         if (!sci) {
1182                 dev_err(dev, "memory allocation for spi_info failed\n");
1183                 return ERR_PTR(-ENOMEM);
1184         }
1185
1186         if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) {
1187                 dev_warn(dev, "spi bus clock parent not specified, using clock at index 0 as parent\n");
1188                 sci->src_clk_nr = 0;
1189         } else {
1190                 sci->src_clk_nr = temp;
1191         }
1192
1193         if (of_property_read_u32(dev->of_node, "num-cs", &temp)) {
1194                 dev_warn(dev, "number of chip select lines not specified, assuming 1 chip select line\n");
1195                 sci->num_cs = 1;
1196         } else {
1197                 sci->num_cs = temp;
1198         }
1199
1200         return sci;
1201 }
1202 #else
1203 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
1204 {
1205         return dev->platform_data;
1206 }
1207 #endif
1208
1209 static const struct of_device_id s3c64xx_spi_dt_match[];
1210
1211 static inline struct s3c64xx_spi_port_config *s3c64xx_spi_get_port_config(
1212                                                 struct platform_device *pdev)
1213 {
1214 #ifdef CONFIG_OF
1215         if (pdev->dev.of_node) {
1216                 const struct of_device_id *match;
1217                 match = of_match_node(s3c64xx_spi_dt_match, pdev->dev.of_node);
1218                 return (struct s3c64xx_spi_port_config *)match->data;
1219         }
1220 #endif
1221         return (struct s3c64xx_spi_port_config *)
1222                          platform_get_device_id(pdev)->driver_data;
1223 }
1224
1225 static int s3c64xx_spi_probe(struct platform_device *pdev)
1226 {
1227         struct resource *mem_res;
1228         struct resource *res;
1229         struct s3c64xx_spi_driver_data *sdd;
1230         struct s3c64xx_spi_info *sci = pdev->dev.platform_data;
1231         struct spi_master *master;
1232         int ret, irq;
1233         char clk_name[16];
1234
1235         if (!sci && pdev->dev.of_node) {
1236                 sci = s3c64xx_spi_parse_dt(&pdev->dev);
1237                 if (IS_ERR(sci))
1238                         return PTR_ERR(sci);
1239         }
1240
1241         if (!sci) {
1242                 dev_err(&pdev->dev, "platform_data missing!\n");
1243                 return -ENODEV;
1244         }
1245
1246         mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1247         if (mem_res == NULL) {
1248                 dev_err(&pdev->dev, "Unable to get SPI MEM resource\n");
1249                 return -ENXIO;
1250         }
1251
1252         irq = platform_get_irq(pdev, 0);
1253         if (irq < 0) {
1254                 dev_warn(&pdev->dev, "Failed to get IRQ: %d\n", irq);
1255                 return irq;
1256         }
1257
1258         master = spi_alloc_master(&pdev->dev,
1259                                 sizeof(struct s3c64xx_spi_driver_data));
1260         if (master == NULL) {
1261                 dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
1262                 return -ENOMEM;
1263         }
1264
1265         platform_set_drvdata(pdev, master);
1266
1267         sdd = spi_master_get_devdata(master);
1268         sdd->port_conf = s3c64xx_spi_get_port_config(pdev);
1269         sdd->master = master;
1270         sdd->cntrlr_info = sci;
1271         sdd->pdev = pdev;
1272         sdd->sfr_start = mem_res->start;
1273         if (pdev->dev.of_node) {
1274                 ret = of_alias_get_id(pdev->dev.of_node, "spi");
1275                 if (ret < 0) {
1276                         dev_err(&pdev->dev, "failed to get alias id, errno %d\n",
1277                                 ret);
1278                         goto err0;
1279                 }
1280                 sdd->port_id = ret;
1281         } else {
1282                 sdd->port_id = pdev->id;
1283         }
1284
1285         sdd->cur_bpw = 8;
1286
1287         if (!sdd->pdev->dev.of_node) {
1288                 res = platform_get_resource(pdev, IORESOURCE_DMA,  0);
1289                 if (!res) {
1290                         dev_err(&pdev->dev, "Unable to get SPI tx dma "
1291                                         "resource\n");
1292                         return -ENXIO;
1293                 }
1294                 sdd->tx_dma.dmach = res->start;
1295
1296                 res = platform_get_resource(pdev, IORESOURCE_DMA,  1);
1297                 if (!res) {
1298                         dev_err(&pdev->dev, "Unable to get SPI rx dma "
1299                                         "resource\n");
1300                         return -ENXIO;
1301                 }
1302                 sdd->rx_dma.dmach = res->start;
1303         }
1304
1305         sdd->tx_dma.direction = DMA_MEM_TO_DEV;
1306         sdd->rx_dma.direction = DMA_DEV_TO_MEM;
1307
1308         master->dev.of_node = pdev->dev.of_node;
1309         master->bus_num = sdd->port_id;
1310         master->setup = s3c64xx_spi_setup;
1311         master->cleanup = s3c64xx_spi_cleanup;
1312         master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer;
1313         master->transfer_one_message = s3c64xx_spi_transfer_one_message;
1314         master->unprepare_transfer_hardware = s3c64xx_spi_unprepare_transfer;
1315         master->num_chipselect = sci->num_cs;
1316         master->dma_alignment = 8;
1317         master->bits_per_word_mask = BIT(32 - 1) | BIT(16 - 1) | BIT(8 - 1);
1318         /* the spi->mode bits understood by this driver: */
1319         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
1320
1321         sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res);
1322         if (IS_ERR(sdd->regs)) {
1323                 ret = PTR_ERR(sdd->regs);
1324                 goto err0;
1325         }
1326
1327         if (sci->cfg_gpio && sci->cfg_gpio()) {
1328                 dev_err(&pdev->dev, "Unable to config gpio\n");
1329                 ret = -EBUSY;
1330                 goto err0;
1331         }
1332
1333         /* Setup clocks */
1334         sdd->clk = devm_clk_get(&pdev->dev, "spi");
1335         if (IS_ERR(sdd->clk)) {
1336                 dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n");
1337                 ret = PTR_ERR(sdd->clk);
1338                 goto err0;
1339         }
1340
1341         if (clk_prepare_enable(sdd->clk)) {
1342                 dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n");
1343                 ret = -EBUSY;
1344                 goto err0;
1345         }
1346
1347         sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr);
1348         sdd->src_clk = devm_clk_get(&pdev->dev, clk_name);
1349         if (IS_ERR(sdd->src_clk)) {
1350                 dev_err(&pdev->dev,
1351                         "Unable to acquire clock '%s'\n", clk_name);
1352                 ret = PTR_ERR(sdd->src_clk);
1353                 goto err2;
1354         }
1355
1356         if (clk_prepare_enable(sdd->src_clk)) {
1357                 dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", clk_name);
1358                 ret = -EBUSY;
1359                 goto err2;
1360         }
1361
1362         /* Setup Deufult Mode */
1363         s3c64xx_spi_hwinit(sdd, sdd->port_id);
1364
1365         spin_lock_init(&sdd->lock);
1366         init_completion(&sdd->xfer_completion);
1367         INIT_LIST_HEAD(&sdd->queue);
1368
1369         ret = devm_request_irq(&pdev->dev, irq, s3c64xx_spi_irq, 0,
1370                                 "spi-s3c64xx", sdd);
1371         if (ret != 0) {
1372                 dev_err(&pdev->dev, "Failed to request IRQ %d: %d\n",
1373                         irq, ret);
1374                 goto err3;
1375         }
1376
1377         writel(S3C64XX_SPI_INT_RX_OVERRUN_EN | S3C64XX_SPI_INT_RX_UNDERRUN_EN |
1378                S3C64XX_SPI_INT_TX_OVERRUN_EN | S3C64XX_SPI_INT_TX_UNDERRUN_EN,
1379                sdd->regs + S3C64XX_SPI_INT_EN);
1380
1381         if (spi_register_master(master)) {
1382                 dev_err(&pdev->dev, "cannot register SPI master\n");
1383                 ret = -EBUSY;
1384                 goto err3;
1385         }
1386
1387         dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d with %d Slaves attached\n",
1388                                         sdd->port_id, master->num_chipselect);
1389         dev_dbg(&pdev->dev, "\tIOmem=[0x%x-0x%x]\tDMA=[Rx-%d, Tx-%d]\n",
1390                                         mem_res->end, mem_res->start,
1391                                         sdd->rx_dma.dmach, sdd->tx_dma.dmach);
1392
1393         pm_runtime_enable(&pdev->dev);
1394
1395         return 0;
1396
1397 err3:
1398         clk_disable_unprepare(sdd->src_clk);
1399 err2:
1400         clk_disable_unprepare(sdd->clk);
1401 err0:
1402         platform_set_drvdata(pdev, NULL);
1403         spi_master_put(master);
1404
1405         return ret;
1406 }
1407
1408 static int s3c64xx_spi_remove(struct platform_device *pdev)
1409 {
1410         struct spi_master *master = spi_master_get(platform_get_drvdata(pdev));
1411         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1412
1413         pm_runtime_disable(&pdev->dev);
1414
1415         spi_unregister_master(master);
1416
1417         writel(0, sdd->regs + S3C64XX_SPI_INT_EN);
1418
1419         clk_disable_unprepare(sdd->src_clk);
1420
1421         clk_disable_unprepare(sdd->clk);
1422
1423         platform_set_drvdata(pdev, NULL);
1424         spi_master_put(master);
1425
1426         return 0;
1427 }
1428
1429 #ifdef CONFIG_PM_SLEEP
1430 static int s3c64xx_spi_suspend(struct device *dev)
1431 {
1432         struct spi_master *master = dev_get_drvdata(dev);
1433         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1434
1435         spi_master_suspend(master);
1436
1437         /* Disable the clock */
1438         clk_disable_unprepare(sdd->src_clk);
1439         clk_disable_unprepare(sdd->clk);
1440
1441         sdd->cur_speed = 0; /* Output Clock is stopped */
1442
1443         return 0;
1444 }
1445
1446 static int s3c64xx_spi_resume(struct device *dev)
1447 {
1448         struct spi_master *master = dev_get_drvdata(dev);
1449         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1450         struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
1451
1452         if (sci->cfg_gpio)
1453                 sci->cfg_gpio();
1454
1455         /* Enable the clock */
1456         clk_prepare_enable(sdd->src_clk);
1457         clk_prepare_enable(sdd->clk);
1458
1459         s3c64xx_spi_hwinit(sdd, sdd->port_id);
1460
1461         spi_master_resume(master);
1462
1463         return 0;
1464 }
1465 #endif /* CONFIG_PM_SLEEP */
1466
1467 #ifdef CONFIG_PM_RUNTIME
1468 static int s3c64xx_spi_runtime_suspend(struct device *dev)
1469 {
1470         struct spi_master *master = dev_get_drvdata(dev);
1471         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1472
1473         clk_disable_unprepare(sdd->clk);
1474         clk_disable_unprepare(sdd->src_clk);
1475
1476         return 0;
1477 }
1478
1479 static int s3c64xx_spi_runtime_resume(struct device *dev)
1480 {
1481         struct spi_master *master = dev_get_drvdata(dev);
1482         struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
1483
1484         clk_prepare_enable(sdd->src_clk);
1485         clk_prepare_enable(sdd->clk);
1486
1487         return 0;
1488 }
1489 #endif /* CONFIG_PM_RUNTIME */
1490
1491 static const struct dev_pm_ops s3c64xx_spi_pm = {
1492         SET_SYSTEM_SLEEP_PM_OPS(s3c64xx_spi_suspend, s3c64xx_spi_resume)
1493         SET_RUNTIME_PM_OPS(s3c64xx_spi_runtime_suspend,
1494                            s3c64xx_spi_runtime_resume, NULL)
1495 };
1496
1497 static struct s3c64xx_spi_port_config s3c2443_spi_port_config = {
1498         .fifo_lvl_mask  = { 0x7f },
1499         .rx_lvl_offset  = 13,
1500         .tx_st_done     = 21,
1501         .high_speed     = true,
1502 };
1503
1504 static struct s3c64xx_spi_port_config s3c6410_spi_port_config = {
1505         .fifo_lvl_mask  = { 0x7f, 0x7F },
1506         .rx_lvl_offset  = 13,
1507         .tx_st_done     = 21,
1508 };
1509
1510 static struct s3c64xx_spi_port_config s5p64x0_spi_port_config = {
1511         .fifo_lvl_mask  = { 0x1ff, 0x7F },
1512         .rx_lvl_offset  = 15,
1513         .tx_st_done     = 25,
1514 };
1515
1516 static struct s3c64xx_spi_port_config s5pc100_spi_port_config = {
1517         .fifo_lvl_mask  = { 0x7f, 0x7F },
1518         .rx_lvl_offset  = 13,
1519         .tx_st_done     = 21,
1520         .high_speed     = true,
1521 };
1522
1523 static struct s3c64xx_spi_port_config s5pv210_spi_port_config = {
1524         .fifo_lvl_mask  = { 0x1ff, 0x7F },
1525         .rx_lvl_offset  = 15,
1526         .tx_st_done     = 25,
1527         .high_speed     = true,
1528 };
1529
1530 static struct s3c64xx_spi_port_config exynos4_spi_port_config = {
1531         .fifo_lvl_mask  = { 0x1ff, 0x7F, 0x7F },
1532         .rx_lvl_offset  = 15,
1533         .tx_st_done     = 25,
1534         .high_speed     = true,
1535         .clk_from_cmu   = true,
1536 };
1537
1538 static struct platform_device_id s3c64xx_spi_driver_ids[] = {
1539         {
1540                 .name           = "s3c2443-spi",
1541                 .driver_data    = (kernel_ulong_t)&s3c2443_spi_port_config,
1542         }, {
1543                 .name           = "s3c6410-spi",
1544                 .driver_data    = (kernel_ulong_t)&s3c6410_spi_port_config,
1545         }, {
1546                 .name           = "s5p64x0-spi",
1547                 .driver_data    = (kernel_ulong_t)&s5p64x0_spi_port_config,
1548         }, {
1549                 .name           = "s5pc100-spi",
1550                 .driver_data    = (kernel_ulong_t)&s5pc100_spi_port_config,
1551         }, {
1552                 .name           = "s5pv210-spi",
1553                 .driver_data    = (kernel_ulong_t)&s5pv210_spi_port_config,
1554         }, {
1555                 .name           = "exynos4210-spi",
1556                 .driver_data    = (kernel_ulong_t)&exynos4_spi_port_config,
1557         },
1558         { },
1559 };
1560
1561 #ifdef CONFIG_OF
1562 static const struct of_device_id s3c64xx_spi_dt_match[] = {
1563         { .compatible = "samsung,exynos4210-spi",
1564                         .data = (void *)&exynos4_spi_port_config,
1565         },
1566         { },
1567 };
1568 MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match);
1569 #endif /* CONFIG_OF */
1570
1571 static struct platform_driver s3c64xx_spi_driver = {
1572         .driver = {
1573                 .name   = "s3c64xx-spi",
1574                 .owner = THIS_MODULE,
1575                 .pm = &s3c64xx_spi_pm,
1576                 .of_match_table = of_match_ptr(s3c64xx_spi_dt_match),
1577         },
1578         .remove = s3c64xx_spi_remove,
1579         .id_table = s3c64xx_spi_driver_ids,
1580 };
1581 MODULE_ALIAS("platform:s3c64xx-spi");
1582
1583 static int __init s3c64xx_spi_init(void)
1584 {
1585         return platform_driver_probe(&s3c64xx_spi_driver, s3c64xx_spi_probe);
1586 }
1587 subsys_initcall(s3c64xx_spi_init);
1588
1589 static void __exit s3c64xx_spi_exit(void)
1590 {
1591         platform_driver_unregister(&s3c64xx_spi_driver);
1592 }
1593 module_exit(s3c64xx_spi_exit);
1594
1595 MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
1596 MODULE_DESCRIPTION("S3C64XX SPI Controller Driver");
1597 MODULE_LICENSE("GPL");