2 * comedi/drivers/dt2801.c
3 * Device Driver for DataTranslation DT2801
8 Description: Data Translation DT2801 series and DT01-EZ
11 Devices: [Data Translation] DT2801 (dt2801), DT2801-A, DT2801/5716A,
12 DT2805, DT2805/5716A, DT2808, DT2818, DT2809, DT01-EZ
14 This driver can autoprobe the type of board.
16 Configuration options:
17 [0] - I/O port base address
19 [2] - A/D reference 0=differential, 1=single-ended
29 [5] - D/A 1 range (same choices)
32 #include "../comedidev.h"
33 #include <linux/delay.h>
34 #include <linux/ioport.h>
36 #define DT2801_TIMEOUT 1000
38 /* Hardware Configuration */
39 /* ====================== */
41 #define DT2801_MAX_DMA_SIZE (64 * 1024)
44 #define DT2801_IOSIZE 2
47 /* ====================== */
50 #define DT_C_RESET 0x0
51 #define DT_C_CLEAR_ERR 0x1
52 #define DT_C_READ_ERRREG 0x2
53 #define DT_C_SET_CLOCK 0x3
58 #define DT_C_SET_DIGIN 0x4
59 #define DT_C_SET_DIGOUT 0x5
60 #define DT_C_READ_DIG 0x6
61 #define DT_C_WRITE_DIG 0x7
63 #define DT_C_WRITE_DAIM 0x8
64 #define DT_C_SET_DA 0x9
65 #define DT_C_WRITE_DA 0xa
67 #define DT_C_READ_ADIM 0xc
68 #define DT_C_SET_AD 0xd
69 #define DT_C_READ_AD 0xe
71 /* Command modifiers (only used with read/write), EXTTRIG can be
72 used with some other commands.
74 #define DT_MOD_DMA (1<<4)
75 #define DT_MOD_CONT (1<<5)
76 #define DT_MOD_EXTCLK (1<<6)
77 #define DT_MOD_EXTTRIG (1<<7)
79 /* Bits in status register */
80 #define DT_S_DATA_OUT_READY (1<<0)
81 #define DT_S_DATA_IN_FULL (1<<1)
82 #define DT_S_READY (1<<2)
83 #define DT_S_COMMAND (1<<3)
84 #define DT_S_COMPOSITE_ERROR (1<<7)
88 #define DT2801_STATUS 1
92 /* ignore 'defined but not used' warning */
93 static const struct comedi_lrange range_dt2801_ai_pgh_bipolar = { 4, {
107 static const struct comedi_lrange range_dt2801_ai_pgl_bipolar = { 4, {
122 /* ignore 'defined but not used' warning */
123 static const struct comedi_lrange range_dt2801_ai_pgh_unipolar = { 4, {
135 static const struct comedi_lrange range_dt2801_ai_pgl_unipolar = { 4, {
147 struct dt2801_board {
158 /* Typeid's for the different boards of the DT2801-series
159 (taken from the test-software, that comes with the board)
161 static const struct dt2801_board boardtypes[] = {
179 .name = "dt2801/5716a",
195 .name = "dt2805/5716a",
228 #define boardtype (*(const struct dt2801_board *)dev->board_ptr)
230 struct dt2801_private {
232 const struct comedi_lrange *dac_range_types[2];
233 unsigned int ao_readback[2];
236 #define devpriv ((struct dt2801_private *)dev->private)
238 /* These are the low-level routines:
239 writecommand: write a command to the board
240 writedata: write data byte
241 readdata: read data byte
244 /* Only checks DataOutReady-flag, not the Ready-flag as it is done
245 in the examples of the manual. I don't see why this should be
247 static int dt2801_readdata(struct comedi_device *dev, int *data)
250 int timeout = DT2801_TIMEOUT;
253 stat = inb_p(dev->iobase + DT2801_STATUS);
254 if (stat & (DT_S_COMPOSITE_ERROR | DT_S_READY))
256 if (stat & DT_S_DATA_OUT_READY) {
257 *data = inb_p(dev->iobase + DT2801_DATA);
260 } while (--timeout > 0);
265 static int dt2801_readdata2(struct comedi_device *dev, int *data)
270 ret = dt2801_readdata(dev, &lb);
273 ret = dt2801_readdata(dev, &hb);
277 *data = (hb << 8) + lb;
281 static int dt2801_writedata(struct comedi_device *dev, unsigned int data)
284 int timeout = DT2801_TIMEOUT;
287 stat = inb_p(dev->iobase + DT2801_STATUS);
289 if (stat & DT_S_COMPOSITE_ERROR)
291 if (!(stat & DT_S_DATA_IN_FULL)) {
292 outb_p(data & 0xff, dev->iobase + DT2801_DATA);
296 if (stat & DT_S_READY) {
298 ("dt2801: ready flag set (bad!) in dt2801_writedata()\n");
302 } while (--timeout > 0);
307 static int dt2801_writedata2(struct comedi_device *dev, unsigned int data)
311 ret = dt2801_writedata(dev, data & 0xff);
314 ret = dt2801_writedata(dev, (data >> 8));
321 static int dt2801_wait_for_ready(struct comedi_device *dev)
323 int timeout = DT2801_TIMEOUT;
326 stat = inb_p(dev->iobase + DT2801_STATUS);
327 if (stat & DT_S_READY)
330 stat = inb_p(dev->iobase + DT2801_STATUS);
332 if (stat & DT_S_COMPOSITE_ERROR)
334 if (stat & DT_S_READY)
336 } while (--timeout > 0);
341 static int dt2801_writecmd(struct comedi_device *dev, int command)
345 dt2801_wait_for_ready(dev);
347 stat = inb_p(dev->iobase + DT2801_STATUS);
348 if (stat & DT_S_COMPOSITE_ERROR) {
350 ("dt2801: composite-error in dt2801_writecmd(), ignoring\n");
352 if (!(stat & DT_S_READY))
353 printk("dt2801: !ready in dt2801_writecmd(), ignoring\n");
354 outb_p(command, dev->iobase + DT2801_CMD);
359 static int dt2801_reset(struct comedi_device *dev)
365 DPRINTK("dt2801: resetting board...\n");
366 DPRINTK("fingerprint: 0x%02x 0x%02x\n", inb_p(dev->iobase),
367 inb_p(dev->iobase + 1));
369 /* pull random data from data port */
370 inb_p(dev->iobase + DT2801_DATA);
371 inb_p(dev->iobase + DT2801_DATA);
372 inb_p(dev->iobase + DT2801_DATA);
373 inb_p(dev->iobase + DT2801_DATA);
375 DPRINTK("dt2801: stop\n");
376 /* dt2801_writecmd(dev,DT_C_STOP); */
377 outb_p(DT_C_STOP, dev->iobase + DT2801_CMD);
379 /* dt2801_wait_for_ready(dev); */
383 stat = inb_p(dev->iobase + DT2801_STATUS);
384 if (stat & DT_S_READY)
388 printk("dt2801: timeout 1 status=0x%02x\n", stat);
390 /* printk("dt2801: reading dummy\n"); */
391 /* dt2801_readdata(dev,&board_code); */
393 DPRINTK("dt2801: reset\n");
394 outb_p(DT_C_RESET, dev->iobase + DT2801_CMD);
395 /* dt2801_writecmd(dev,DT_C_RESET); */
400 stat = inb_p(dev->iobase + DT2801_STATUS);
401 if (stat & DT_S_READY)
405 printk("dt2801: timeout 2 status=0x%02x\n", stat);
407 DPRINTK("dt2801: reading code\n");
408 dt2801_readdata(dev, &board_code);
410 DPRINTK("dt2801: ok. code=0x%02x\n", board_code);
415 static int probe_number_of_ai_chans(struct comedi_device *dev)
421 for (n_chans = 0; n_chans < 16; n_chans++) {
422 stat = dt2801_writecmd(dev, DT_C_READ_ADIM);
423 dt2801_writedata(dev, 0);
424 dt2801_writedata(dev, n_chans);
425 stat = dt2801_readdata2(dev, &data);
437 static const struct comedi_lrange *dac_range_table[] = {
445 static const struct comedi_lrange *dac_range_lkup(int opt)
447 if (opt < 0 || opt >= 5)
448 return &range_unknown;
449 return dac_range_table[opt];
452 static const struct comedi_lrange *ai_range_lkup(int type, int opt)
457 &range_dt2801_ai_pgl_unipolar :
458 &range_dt2801_ai_pgl_bipolar;
460 return (opt) ? &range_unipolar10 : &range_bipolar10;
462 return &range_unipolar5;
464 return &range_unknown;
467 static int dt2801_error(struct comedi_device *dev, int stat)
471 printk("dt2801: timeout\n");
473 printk("dt2801: error %d\n", stat);
476 printk("dt2801: error status 0x%02x, resetting...\n", stat);
484 static int dt2801_ai_insn_read(struct comedi_device *dev,
485 struct comedi_subdevice *s,
486 struct comedi_insn *insn, unsigned int *data)
492 for (i = 0; i < insn->n; i++) {
493 stat = dt2801_writecmd(dev, DT_C_READ_ADIM);
494 dt2801_writedata(dev, CR_RANGE(insn->chanspec));
495 dt2801_writedata(dev, CR_CHAN(insn->chanspec));
496 stat = dt2801_readdata2(dev, &d);
499 return dt2801_error(dev, stat);
507 static int dt2801_ao_insn_read(struct comedi_device *dev,
508 struct comedi_subdevice *s,
509 struct comedi_insn *insn, unsigned int *data)
511 data[0] = devpriv->ao_readback[CR_CHAN(insn->chanspec)];
516 static int dt2801_ao_insn_write(struct comedi_device *dev,
517 struct comedi_subdevice *s,
518 struct comedi_insn *insn, unsigned int *data)
520 dt2801_writecmd(dev, DT_C_WRITE_DAIM);
521 dt2801_writedata(dev, CR_CHAN(insn->chanspec));
522 dt2801_writedata2(dev, data[0]);
524 devpriv->ao_readback[CR_CHAN(insn->chanspec)] = data[0];
529 static int dt2801_dio_insn_bits(struct comedi_device *dev,
530 struct comedi_subdevice *s,
531 struct comedi_insn *insn, unsigned int *data)
535 if (s == dev->subdevices + 4)
539 s->state &= ~data[0];
540 s->state |= (data[0] & data[1]);
541 dt2801_writecmd(dev, DT_C_WRITE_DIG);
542 dt2801_writedata(dev, which);
543 dt2801_writedata(dev, s->state);
545 dt2801_writecmd(dev, DT_C_READ_DIG);
546 dt2801_writedata(dev, which);
547 dt2801_readdata(dev, data + 1);
552 static int dt2801_dio_insn_config(struct comedi_device *dev,
553 struct comedi_subdevice *s,
554 struct comedi_insn *insn, unsigned int *data)
558 if (s == dev->subdevices + 4)
563 case INSN_CONFIG_DIO_OUTPUT:
565 dt2801_writecmd(dev, DT_C_SET_DIGOUT);
567 case INSN_CONFIG_DIO_INPUT:
569 dt2801_writecmd(dev, DT_C_SET_DIGIN);
571 case INSN_CONFIG_DIO_QUERY:
572 data[1] = s->io_bits ? COMEDI_OUTPUT : COMEDI_INPUT;
577 dt2801_writedata(dev, which);
586 [2] - a/d 0=differential, 1=single-ended
587 [3] - a/d range 0=[-10,10], 1=[0,10]
588 [4] - dac0 range 0=[-10,10], 1=[-5,5], 2=[-2.5,2.5] 3=[0,10], 4=[0,5]
589 [5] - dac1 range 0=[-10,10], 1=[-5,5], 2=[-2.5,2.5] 3=[0,10], 4=[0,5]
591 static int dt2801_attach(struct comedi_device *dev, struct comedi_devconfig *it)
593 struct comedi_subdevice *s;
594 unsigned long iobase;
595 int board_code, type;
599 iobase = it->options[0];
600 if (!request_region(iobase, DT2801_IOSIZE, "dt2801")) {
601 comedi_error(dev, "I/O port conflict");
604 dev->iobase = iobase;
606 /* do some checking */
608 board_code = dt2801_reset(dev);
610 /* heh. if it didn't work, try it again. */
612 board_code = dt2801_reset(dev);
614 for (type = 0; type < ARRAY_SIZE(boardtypes); type++) {
615 if (boardtypes[type].boardcode == board_code)
618 printk("dt2801: unrecognized board code=0x%02x, contact author\n",
623 dev->board_ptr = boardtypes + type;
624 printk("dt2801: %s at port 0x%lx", boardtype.name, iobase);
626 n_ai_chans = probe_number_of_ai_chans(dev);
627 printk(" (ai channels = %d)\n", n_ai_chans);
629 ret = comedi_alloc_subdevices(dev, 4);
633 ret = alloc_private(dev, sizeof(struct dt2801_private));
637 dev->board_name = boardtype.name;
639 s = dev->subdevices + 0;
641 s->type = COMEDI_SUBD_AI;
642 s->subdev_flags = SDF_READABLE | SDF_GROUND;
644 s->n_chan = n_ai_chans;
647 s->n_chan = boardtype.ad_chan;
649 s->n_chan = boardtype.ad_chan / 2;
651 s->maxdata = (1 << boardtype.adbits) - 1;
652 s->range_table = ai_range_lkup(boardtype.adrangetype, it->options[3]);
653 s->insn_read = dt2801_ai_insn_read;
657 s->type = COMEDI_SUBD_AO;
658 s->subdev_flags = SDF_WRITABLE;
660 s->maxdata = (1 << boardtype.dabits) - 1;
661 s->range_table_list = devpriv->dac_range_types;
662 devpriv->dac_range_types[0] = dac_range_lkup(it->options[4]);
663 devpriv->dac_range_types[1] = dac_range_lkup(it->options[5]);
664 s->insn_read = dt2801_ao_insn_read;
665 s->insn_write = dt2801_ao_insn_write;
668 /* 1st digital subdevice */
669 s->type = COMEDI_SUBD_DIO;
670 s->subdev_flags = SDF_READABLE | SDF_WRITABLE;
673 s->range_table = &range_digital;
674 s->insn_bits = dt2801_dio_insn_bits;
675 s->insn_config = dt2801_dio_insn_config;
678 /* 2nd digital subdevice */
679 s->type = COMEDI_SUBD_DIO;
680 s->subdev_flags = SDF_READABLE | SDF_WRITABLE;
683 s->range_table = &range_digital;
684 s->insn_bits = dt2801_dio_insn_bits;
685 s->insn_config = dt2801_dio_insn_config;
692 static void dt2801_detach(struct comedi_device *dev)
695 release_region(dev->iobase, DT2801_IOSIZE);
698 static struct comedi_driver dt2801_driver = {
699 .driver_name = "dt2801",
700 .module = THIS_MODULE,
701 .attach = dt2801_attach,
702 .detach = dt2801_detach,
704 module_comedi_driver(dt2801_driver);
706 MODULE_AUTHOR("Comedi http://www.comedi.org");
707 MODULE_DESCRIPTION("Comedi low-level driver");
708 MODULE_LICENSE("GPL");