3 Sensoray s626 Comedi driver
5 COMEDI - Linux Control and Measurement Device Interface
6 Copyright (C) 2000 David A. Schleef <ds@schleef.org>
8 Based on Sensoray Model 626 Linux driver Version 0.2
9 Copyright (C) 2002-2004 Sensoray Co., Inc.
11 This program is free software; you can redistribute it and/or modify
12 it under the terms of the GNU General Public License as published by
13 the Free Software Foundation; either version 2 of the License, or
14 (at your option) any later version.
16 This program is distributed in the hope that it will be useful,
17 but WITHOUT ANY WARRANTY; without even the implied warranty of
18 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
19 GNU General Public License for more details.
21 You should have received a copy of the GNU General Public License
22 along with this program; if not, write to the Free Software
23 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
29 Description: Sensoray 626 driver
30 Devices: [Sensoray] 626 (s626)
31 Authors: Gianluca Palli <gpalli@deis.unibo.it>,
32 Updated: Fri, 15 Feb 2008 10:28:42 +0000
35 Configuration options:
36 [0] - PCI bus of device (optional)
37 [1] - PCI slot of device (optional)
38 If bus/slot is not specified, the first supported
39 PCI device found will be used.
41 INSN_CONFIG instructions:
49 s626 has 3 dio subdevices (2,3 and 4) each with 16 i/o channels
50 supported configuration options:
56 Every channel must be configured before reading.
60 insn.insn=INSN_CONFIG; //configuration instruction
61 insn.n=1; //number of operation (must be 1)
62 insn.data=&initialvalue; //initial value loaded into encoder
63 //during configuration
64 insn.subdev=5; //encoder subdevice
65 insn.chanspec=CR_PACK(encoder_channel,0,AREF_OTHER); //encoder_channel
68 comedi_do_insn(cf,&insn); //executing configuration
71 #include <linux/interrupt.h>
72 #include <linux/kernel.h>
73 #include <linux/types.h>
75 #include "../comedidev.h"
77 #include "comedi_pci.h"
79 #include "comedi_fc.h"
82 MODULE_AUTHOR("Gianluca Palli <gpalli@deis.unibo.it>");
83 MODULE_DESCRIPTION("Sensoray 626 Comedi driver module");
84 MODULE_LICENSE("GPL");
97 static const struct s626_board s626_boards[] = {
100 .ai_chans = S626_ADC_CHANNELS,
102 .ao_chans = S626_DAC_CHANNELS,
104 .dio_chans = S626_DIO_CHANNELS,
105 .dio_banks = S626_DIO_BANKS,
106 .enc_chans = S626_ENCODER_CHANNELS,
110 #define thisboard ((const struct s626_board *)dev->board_ptr)
111 #define PCI_VENDOR_ID_S626 0x1131
112 #define PCI_DEVICE_ID_S626 0x7146
115 * For devices with vendor:device id == 0x1131:0x7146 you must specify
116 * also subvendor:subdevice ids, because otherwise it will conflict with
117 * Philips SAA7146 media/dvb based cards.
119 static DEFINE_PCI_DEVICE_TABLE(s626_pci_table) = {
120 {PCI_VENDOR_ID_S626, PCI_DEVICE_ID_S626, 0x6000, 0x0272, 0, 0, 0},
124 MODULE_DEVICE_TABLE(pci, s626_pci_table);
126 static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it);
127 static int s626_detach(struct comedi_device *dev);
129 static struct comedi_driver driver_s626 = {
130 .driver_name = "s626",
131 .module = THIS_MODULE,
132 .attach = s626_attach,
133 .detach = s626_detach,
136 struct s626_private {
137 struct pci_dev *pdev;
141 uint8_t ai_cmd_running; /* ai_cmd is running */
142 uint8_t ai_continous; /* continous acquisition */
143 int ai_sample_count; /* number of samples to acquire */
144 unsigned int ai_sample_timer;
145 /* time between samples in units of the timer */
146 int ai_convert_count; /* conversion counter */
147 unsigned int ai_convert_timer;
148 /* time between conversion in units of the timer */
149 uint16_t CounterIntEnabs;
150 /* Counter interrupt enable mask for MISC2 register. */
151 uint8_t AdcItems; /* Number of items in ADC poll list. */
152 struct bufferDMA RPSBuf; /* DMA buffer used to hold ADC (RPS1) program. */
153 struct bufferDMA ANABuf;
154 /* DMA buffer used to receive ADC data and hold DAC data. */
156 /* Pointer to logical adrs of DMA buffer used to hold DAC data. */
157 uint16_t Dacpol; /* Image of DAC polarity register. */
158 uint8_t TrimSetpoint[12]; /* Images of TrimDAC setpoints */
159 uint16_t ChargeEnabled; /* Image of MISC2 Battery */
160 /* Charge Enabled (0 or WRMISC2_CHARGE_ENABLE). */
161 uint16_t WDInterval; /* Image of MISC2 watchdog interval control bits. */
163 /* I2C device address for onboard EEPROM (board rev dependent). */
165 unsigned int ao_readback[S626_DAC_CHANNELS];
180 static struct dio_private dio_private_A = {
182 .WRDOut = LP_WRDOUTA,
183 .RDEdgSel = LP_RDEDGSELA,
184 .WREdgSel = LP_WREDGSELA,
185 .RDCapSel = LP_RDCAPSELA,
186 .WRCapSel = LP_WRCAPSELA,
187 .RDCapFlg = LP_RDCAPFLGA,
188 .RDIntSel = LP_RDINTSELA,
189 .WRIntSel = LP_WRINTSELA,
192 static struct dio_private dio_private_B = {
194 .WRDOut = LP_WRDOUTB,
195 .RDEdgSel = LP_RDEDGSELB,
196 .WREdgSel = LP_WREDGSELB,
197 .RDCapSel = LP_RDCAPSELB,
198 .WRCapSel = LP_WRCAPSELB,
199 .RDCapFlg = LP_RDCAPFLGB,
200 .RDIntSel = LP_RDINTSELB,
201 .WRIntSel = LP_WRINTSELB,
204 static struct dio_private dio_private_C = {
206 .WRDOut = LP_WRDOUTC,
207 .RDEdgSel = LP_RDEDGSELC,
208 .WREdgSel = LP_WREDGSELC,
209 .RDCapSel = LP_RDCAPSELC,
210 .WRCapSel = LP_WRCAPSELC,
211 .RDCapFlg = LP_RDCAPFLGC,
212 .RDIntSel = LP_RDINTSELC,
213 .WRIntSel = LP_WRINTSELC,
216 /* to group dio devices (48 bits mask and data are not allowed ???)
217 static struct dio_private *dio_private_word[]={
224 #define devpriv ((struct s626_private *)dev->private)
225 #define diopriv ((struct dio_private *)s->private)
227 static int __devinit driver_s626_pci_probe(struct pci_dev *dev,
228 const struct pci_device_id *ent)
230 return comedi_pci_auto_config(dev, driver_s626.driver_name);
233 static void __devexit driver_s626_pci_remove(struct pci_dev *dev)
235 comedi_pci_auto_unconfig(dev);
238 static struct pci_driver driver_s626_pci_driver = {
239 .id_table = s626_pci_table,
240 .probe = &driver_s626_pci_probe,
241 .remove = __devexit_p(&driver_s626_pci_remove)
244 static int __init driver_s626_init_module(void)
248 retval = comedi_driver_register(&driver_s626);
252 driver_s626_pci_driver.name = (char *)driver_s626.driver_name;
253 return pci_register_driver(&driver_s626_pci_driver);
256 static void __exit driver_s626_cleanup_module(void)
258 pci_unregister_driver(&driver_s626_pci_driver);
259 comedi_driver_unregister(&driver_s626);
262 module_init(driver_s626_init_module);
263 module_exit(driver_s626_cleanup_module);
266 static int s626_ai_insn_config(struct comedi_device *dev,
267 struct comedi_subdevice *s,
268 struct comedi_insn *insn, unsigned int *data);
269 /* static int s626_ai_rinsn(struct comedi_device *dev,struct comedi_subdevice *s,struct comedi_insn *insn,unsigned int *data); */
270 static int s626_ai_insn_read(struct comedi_device *dev,
271 struct comedi_subdevice *s,
272 struct comedi_insn *insn, unsigned int *data);
273 static int s626_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s);
274 static int s626_ai_cmdtest(struct comedi_device *dev,
275 struct comedi_subdevice *s, struct comedi_cmd *cmd);
276 static int s626_ai_cancel(struct comedi_device *dev,
277 struct comedi_subdevice *s);
278 static int s626_ao_winsn(struct comedi_device *dev, struct comedi_subdevice *s,
279 struct comedi_insn *insn, unsigned int *data);
280 static int s626_ao_rinsn(struct comedi_device *dev, struct comedi_subdevice *s,
281 struct comedi_insn *insn, unsigned int *data);
282 static int s626_dio_insn_bits(struct comedi_device *dev,
283 struct comedi_subdevice *s,
284 struct comedi_insn *insn, unsigned int *data);
285 static int s626_dio_insn_config(struct comedi_device *dev,
286 struct comedi_subdevice *s,
287 struct comedi_insn *insn, unsigned int *data);
288 static int s626_dio_set_irq(struct comedi_device *dev, unsigned int chan);
289 static int s626_dio_reset_irq(struct comedi_device *dev, unsigned int gruop,
291 static int s626_dio_clear_irq(struct comedi_device *dev);
292 static int s626_enc_insn_config(struct comedi_device *dev,
293 struct comedi_subdevice *s,
294 struct comedi_insn *insn, unsigned int *data);
295 static int s626_enc_insn_read(struct comedi_device *dev,
296 struct comedi_subdevice *s,
297 struct comedi_insn *insn, unsigned int *data);
298 static int s626_enc_insn_write(struct comedi_device *dev,
299 struct comedi_subdevice *s,
300 struct comedi_insn *insn, unsigned int *data);
301 static int s626_ns_to_timer(int *nanosec, int round_mode);
302 static int s626_ai_load_polllist(uint8_t *ppl, struct comedi_cmd *cmd);
303 static int s626_ai_inttrig(struct comedi_device *dev,
304 struct comedi_subdevice *s, unsigned int trignum);
305 static irqreturn_t s626_irq_handler(int irq, void *d);
306 static unsigned int s626_ai_reg_to_uint(int data);
307 /* static unsigned int s626_uint_to_reg(struct comedi_subdevice *s, int data); */
309 /* end ioctl routines */
311 /* internal routines */
312 static void s626_dio_init(struct comedi_device *dev);
313 static void ResetADC(struct comedi_device *dev, uint8_t * ppl);
314 static void LoadTrimDACs(struct comedi_device *dev);
315 static void WriteTrimDAC(struct comedi_device *dev, uint8_t LogicalChan,
317 static uint8_t I2Cread(struct comedi_device *dev, uint8_t addr);
318 static uint32_t I2Chandshake(struct comedi_device *dev, uint32_t val);
319 static void SetDAC(struct comedi_device *dev, uint16_t chan, short dacdata);
320 static void SendDAC(struct comedi_device *dev, uint32_t val);
321 static void WriteMISC2(struct comedi_device *dev, uint16_t NewImage);
322 static void DEBItransfer(struct comedi_device *dev);
323 static uint16_t DEBIread(struct comedi_device *dev, uint16_t addr);
324 static void DEBIwrite(struct comedi_device *dev, uint16_t addr, uint16_t wdata);
325 static void DEBIreplace(struct comedi_device *dev, uint16_t addr, uint16_t mask,
327 static void CloseDMAB(struct comedi_device *dev, struct bufferDMA *pdma,
330 /* COUNTER OBJECT ------------------------------------------------ */
332 /* Pointers to functions that differ for A and B counters: */
333 uint16_t(*GetEnable) (struct comedi_device *dev, struct enc_private *); /* Return clock enable. */
334 uint16_t(*GetIntSrc) (struct comedi_device *dev, struct enc_private *); /* Return interrupt source. */
335 uint16_t(*GetLoadTrig) (struct comedi_device *dev, struct enc_private *); /* Return preload trigger source. */
336 uint16_t(*GetMode) (struct comedi_device *dev, struct enc_private *); /* Return standardized operating mode. */
337 void (*PulseIndex) (struct comedi_device *dev, struct enc_private *); /* Generate soft index strobe. */
338 void (*SetEnable) (struct comedi_device *dev, struct enc_private *, uint16_t enab); /* Program clock enable. */
339 void (*SetIntSrc) (struct comedi_device *dev, struct enc_private *, uint16_t IntSource); /* Program interrupt source. */
340 void (*SetLoadTrig) (struct comedi_device *dev, struct enc_private *, uint16_t Trig); /* Program preload trigger source. */
341 void (*SetMode) (struct comedi_device *dev, struct enc_private *, uint16_t Setup, uint16_t DisableIntSrc); /* Program standardized operating mode. */
342 void (*ResetCapFlags) (struct comedi_device *dev, struct enc_private *); /* Reset event capture flags. */
344 uint16_t MyCRA; /* Address of CRA register. */
345 uint16_t MyCRB; /* Address of CRB register. */
346 uint16_t MyLatchLsw; /* Address of Latch least-significant-word */
348 uint16_t MyEventBits[4]; /* Bit translations for IntSrc -->RDMISC2. */
351 #define encpriv ((struct enc_private *)(dev->subdevices+5)->private)
353 /* counters routines */
354 static void s626_timer_load(struct comedi_device *dev, struct enc_private *k,
356 static uint32_t ReadLatch(struct comedi_device *dev, struct enc_private *k);
357 static void ResetCapFlags_A(struct comedi_device *dev, struct enc_private *k);
358 static void ResetCapFlags_B(struct comedi_device *dev, struct enc_private *k);
359 static uint16_t GetMode_A(struct comedi_device *dev, struct enc_private *k);
360 static uint16_t GetMode_B(struct comedi_device *dev, struct enc_private *k);
361 static void SetMode_A(struct comedi_device *dev, struct enc_private *k,
362 uint16_t Setup, uint16_t DisableIntSrc);
363 static void SetMode_B(struct comedi_device *dev, struct enc_private *k,
364 uint16_t Setup, uint16_t DisableIntSrc);
365 static void SetEnable_A(struct comedi_device *dev, struct enc_private *k,
367 static void SetEnable_B(struct comedi_device *dev, struct enc_private *k,
369 static uint16_t GetEnable_A(struct comedi_device *dev, struct enc_private *k);
370 static uint16_t GetEnable_B(struct comedi_device *dev, struct enc_private *k);
371 static void SetLatchSource(struct comedi_device *dev, struct enc_private *k,
373 /* static uint16_t GetLatchSource(struct comedi_device *dev, struct enc_private *k ); */
374 static void SetLoadTrig_A(struct comedi_device *dev, struct enc_private *k,
376 static void SetLoadTrig_B(struct comedi_device *dev, struct enc_private *k,
378 static uint16_t GetLoadTrig_A(struct comedi_device *dev, struct enc_private *k);
379 static uint16_t GetLoadTrig_B(struct comedi_device *dev, struct enc_private *k);
380 static void SetIntSrc_B(struct comedi_device *dev, struct enc_private *k,
382 static void SetIntSrc_A(struct comedi_device *dev, struct enc_private *k,
384 static uint16_t GetIntSrc_A(struct comedi_device *dev, struct enc_private *k);
385 static uint16_t GetIntSrc_B(struct comedi_device *dev, struct enc_private *k);
386 /* static void SetClkMult(struct comedi_device *dev, struct enc_private *k, uint16_t value ) ; */
387 /* static uint16_t GetClkMult(struct comedi_device *dev, struct enc_private *k ) ; */
388 /* static void SetIndexPol(struct comedi_device *dev, struct enc_private *k, uint16_t value ); */
389 /* static uint16_t GetClkPol(struct comedi_device *dev, struct enc_private *k ) ; */
390 /* static void SetIndexSrc( struct comedi_device *dev,struct enc_private *k, uint16_t value ); */
391 /* static uint16_t GetClkSrc( struct comedi_device *dev,struct enc_private *k ); */
392 /* static void SetIndexSrc( struct comedi_device *dev,struct enc_private *k, uint16_t value ); */
393 /* static uint16_t GetIndexSrc( struct comedi_device *dev,struct enc_private *k ); */
394 static void PulseIndex_A(struct comedi_device *dev, struct enc_private *k);
395 static void PulseIndex_B(struct comedi_device *dev, struct enc_private *k);
396 static void Preload(struct comedi_device *dev, struct enc_private *k,
398 static void CountersInit(struct comedi_device *dev);
399 /* end internal routines */
401 /* Counter objects constructor. */
403 /* Counter overflow/index event flag masks for RDMISC2. */
404 #define INDXMASK(C) (1 << (((C) > 2) ? ((C) * 2 - 1) : ((C) * 2 + 4)))
405 #define OVERMASK(C) (1 << (((C) > 2) ? ((C) * 2 + 5) : ((C) * 2 + 10)))
406 #define EVBITS(C) { 0, OVERMASK(C), INDXMASK(C), OVERMASK(C) | INDXMASK(C) }
408 /* Translation table to map IntSrc into equivalent RDMISC2 event flag bits. */
409 /* static const uint16_t EventBits[][4] = { EVBITS(0), EVBITS(1), EVBITS(2), EVBITS(3), EVBITS(4), EVBITS(5) }; */
411 /* struct enc_private; */
412 static struct enc_private enc_private_data[] = {
414 .GetEnable = GetEnable_A,
415 .GetIntSrc = GetIntSrc_A,
416 .GetLoadTrig = GetLoadTrig_A,
417 .GetMode = GetMode_A,
418 .PulseIndex = PulseIndex_A,
419 .SetEnable = SetEnable_A,
420 .SetIntSrc = SetIntSrc_A,
421 .SetLoadTrig = SetLoadTrig_A,
422 .SetMode = SetMode_A,
423 .ResetCapFlags = ResetCapFlags_A,
426 .MyLatchLsw = LP_CNTR0ALSW,
427 .MyEventBits = EVBITS(0),
430 .GetEnable = GetEnable_A,
431 .GetIntSrc = GetIntSrc_A,
432 .GetLoadTrig = GetLoadTrig_A,
433 .GetMode = GetMode_A,
434 .PulseIndex = PulseIndex_A,
435 .SetEnable = SetEnable_A,
436 .SetIntSrc = SetIntSrc_A,
437 .SetLoadTrig = SetLoadTrig_A,
438 .SetMode = SetMode_A,
439 .ResetCapFlags = ResetCapFlags_A,
442 .MyLatchLsw = LP_CNTR1ALSW,
443 .MyEventBits = EVBITS(1),
446 .GetEnable = GetEnable_A,
447 .GetIntSrc = GetIntSrc_A,
448 .GetLoadTrig = GetLoadTrig_A,
449 .GetMode = GetMode_A,
450 .PulseIndex = PulseIndex_A,
451 .SetEnable = SetEnable_A,
452 .SetIntSrc = SetIntSrc_A,
453 .SetLoadTrig = SetLoadTrig_A,
454 .SetMode = SetMode_A,
455 .ResetCapFlags = ResetCapFlags_A,
458 .MyLatchLsw = LP_CNTR2ALSW,
459 .MyEventBits = EVBITS(2),
462 .GetEnable = GetEnable_B,
463 .GetIntSrc = GetIntSrc_B,
464 .GetLoadTrig = GetLoadTrig_B,
465 .GetMode = GetMode_B,
466 .PulseIndex = PulseIndex_B,
467 .SetEnable = SetEnable_B,
468 .SetIntSrc = SetIntSrc_B,
469 .SetLoadTrig = SetLoadTrig_B,
470 .SetMode = SetMode_B,
471 .ResetCapFlags = ResetCapFlags_B,
474 .MyLatchLsw = LP_CNTR0BLSW,
475 .MyEventBits = EVBITS(3),
478 .GetEnable = GetEnable_B,
479 .GetIntSrc = GetIntSrc_B,
480 .GetLoadTrig = GetLoadTrig_B,
481 .GetMode = GetMode_B,
482 .PulseIndex = PulseIndex_B,
483 .SetEnable = SetEnable_B,
484 .SetIntSrc = SetIntSrc_B,
485 .SetLoadTrig = SetLoadTrig_B,
486 .SetMode = SetMode_B,
487 .ResetCapFlags = ResetCapFlags_B,
490 .MyLatchLsw = LP_CNTR1BLSW,
491 .MyEventBits = EVBITS(4),
494 .GetEnable = GetEnable_B,
495 .GetIntSrc = GetIntSrc_B,
496 .GetLoadTrig = GetLoadTrig_B,
497 .GetMode = GetMode_B,
498 .PulseIndex = PulseIndex_B,
499 .SetEnable = SetEnable_B,
500 .SetIntSrc = SetIntSrc_B,
501 .SetLoadTrig = SetLoadTrig_B,
502 .SetMode = SetMode_B,
503 .ResetCapFlags = ResetCapFlags_B,
506 .MyLatchLsw = LP_CNTR2BLSW,
507 .MyEventBits = EVBITS(5),
511 /* enab/disable a function or test status bit(s) that are accessed */
512 /* through Main Control Registers 1 or 2. */
513 #define MC_ENABLE(REGADRS, CTRLWORD) writel(((uint32_t)(CTRLWORD) << 16) | (uint32_t)(CTRLWORD), devpriv->base_addr+(REGADRS))
515 #define MC_DISABLE(REGADRS, CTRLWORD) writel((uint32_t)(CTRLWORD) << 16 , devpriv->base_addr+(REGADRS))
517 #define MC_TEST(REGADRS, CTRLWORD) ((readl(devpriv->base_addr+(REGADRS)) & CTRLWORD) != 0)
519 /* #define WR7146(REGARDS,CTRLWORD)
520 writel(CTRLWORD,(uint32_t)(devpriv->base_addr+(REGARDS))) */
521 #define WR7146(REGARDS, CTRLWORD) writel(CTRLWORD, devpriv->base_addr+(REGARDS))
523 /* #define RR7146(REGARDS)
524 readl((uint32_t)(devpriv->base_addr+(REGARDS))) */
525 #define RR7146(REGARDS) readl(devpriv->base_addr+(REGARDS))
527 #define BUGFIX_STREG(REGADRS) (REGADRS - 4)
529 /* Write a time slot control record to TSL2. */
530 #define VECTPORT(VECTNUM) (P_TSL2 + ((VECTNUM) << 2))
531 #define SETVECT(VECTNUM, VECTVAL) WR7146(VECTPORT(VECTNUM), (VECTVAL))
533 /* Code macros used for constructing I2C command bytes. */
534 #define I2C_B2(ATTR, VAL) (((ATTR) << 6) | ((VAL) << 24))
535 #define I2C_B1(ATTR, VAL) (((ATTR) << 4) | ((VAL) << 16))
536 #define I2C_B0(ATTR, VAL) (((ATTR) << 2) | ((VAL) << 8))
538 static const struct comedi_lrange s626_range_table = { 2, {
544 static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)
546 /* uint8_t PollList; */
547 /* uint16_t AdcData; */
548 /* uint16_t StartVal; */
549 /* uint16_t index; */
550 /* unsigned int data[16]; */
554 resource_size_t resourceStart;
556 struct comedi_subdevice *s;
557 const struct pci_device_id *ids;
558 struct pci_dev *pdev = NULL;
560 if (alloc_private(dev, sizeof(struct s626_private)) < 0)
563 for (i = 0; i < (ARRAY_SIZE(s626_pci_table) - 1) && !pdev; i++) {
564 ids = &s626_pci_table[i];
566 pdev = pci_get_subsys(ids->vendor, ids->device,
567 ids->subvendor, ids->subdevice,
570 if ((it->options[0] || it->options[1]) && pdev) {
571 /* matches requested bus/slot */
572 if (pdev->bus->number == it->options[0] &&
573 PCI_SLOT(pdev->devfn) == it->options[1])
579 devpriv->pdev = pdev;
582 printk(KERN_ERR "s626_attach: Board not present!!!\n");
586 result = comedi_pci_enable(pdev, "s626");
588 printk(KERN_ERR "s626_attach: comedi_pci_enable fails\n");
591 devpriv->got_regions = 1;
593 resourceStart = pci_resource_start(devpriv->pdev, 0);
595 devpriv->base_addr = ioremap(resourceStart, SIZEOF_ADDRESS_SPACE);
596 if (devpriv->base_addr == NULL) {
597 printk(KERN_ERR "s626_attach: IOREMAP failed\n");
601 if (devpriv->base_addr) {
602 /* disable master interrupt */
603 writel(0, devpriv->base_addr + P_IER);
606 writel(MC1_SOFT_RESET, devpriv->base_addr + P_MC1);
608 /* DMA FIXME DMA// */
609 DEBUG("s626_attach: DMA ALLOCATION\n");
611 /* adc buffer allocation */
612 devpriv->allocatedBuf = 0;
614 devpriv->ANABuf.LogicalBase =
615 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, &appdma);
617 if (devpriv->ANABuf.LogicalBase == NULL) {
618 printk(KERN_ERR "s626_attach: DMA Memory mapping error\n");
622 devpriv->ANABuf.PhysicalBase = appdma;
625 ("s626_attach: AllocDMAB ADC Logical=%p, bsize=%d, Physical=0x%x\n",
626 devpriv->ANABuf.LogicalBase, DMABUF_SIZE,
627 (uint32_t) devpriv->ANABuf.PhysicalBase);
629 devpriv->allocatedBuf++;
631 devpriv->RPSBuf.LogicalBase =
632 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, &appdma);
634 if (devpriv->RPSBuf.LogicalBase == NULL) {
635 printk(KERN_ERR "s626_attach: DMA Memory mapping error\n");
639 devpriv->RPSBuf.PhysicalBase = appdma;
642 ("s626_attach: AllocDMAB RPS Logical=%p, bsize=%d, Physical=0x%x\n",
643 devpriv->RPSBuf.LogicalBase, DMABUF_SIZE,
644 (uint32_t) devpriv->RPSBuf.PhysicalBase);
646 devpriv->allocatedBuf++;
650 dev->board_ptr = s626_boards;
651 dev->board_name = thisboard->name;
653 if (alloc_subdevices(dev, 6) < 0)
656 dev->iobase = (unsigned long)devpriv->base_addr;
657 dev->irq = devpriv->pdev->irq;
659 /* set up interrupt handler */
661 printk(KERN_ERR " unknown irq (bad)\n");
663 ret = request_irq(dev->irq, s626_irq_handler, IRQF_SHARED,
667 printk(KERN_ERR " irq not available\n");
672 DEBUG("s626_attach: -- it opts %d,%d --\n",
673 it->options[0], it->options[1]);
675 s = dev->subdevices + 0;
676 /* analog input subdevice */
677 dev->read_subdev = s;
678 /* we support single-ended (ground) and differential */
679 s->type = COMEDI_SUBD_AI;
680 s->subdev_flags = SDF_READABLE | SDF_DIFF | SDF_CMD_READ;
681 s->n_chan = thisboard->ai_chans;
682 s->maxdata = (0xffff >> 2);
683 s->range_table = &s626_range_table;
684 s->len_chanlist = thisboard->ai_chans; /* This is the maximum chanlist
685 length that the board can
687 s->insn_config = s626_ai_insn_config;
688 s->insn_read = s626_ai_insn_read;
689 s->do_cmd = s626_ai_cmd;
690 s->do_cmdtest = s626_ai_cmdtest;
691 s->cancel = s626_ai_cancel;
693 s = dev->subdevices + 1;
694 /* analog output subdevice */
695 s->type = COMEDI_SUBD_AO;
696 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
697 s->n_chan = thisboard->ao_chans;
698 s->maxdata = (0x3fff);
699 s->range_table = &range_bipolar10;
700 s->insn_write = s626_ao_winsn;
701 s->insn_read = s626_ao_rinsn;
703 s = dev->subdevices + 2;
704 /* digital I/O subdevice */
705 s->type = COMEDI_SUBD_DIO;
706 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
707 s->n_chan = S626_DIO_CHANNELS;
710 s->private = &dio_private_A;
711 s->range_table = &range_digital;
712 s->insn_config = s626_dio_insn_config;
713 s->insn_bits = s626_dio_insn_bits;
715 s = dev->subdevices + 3;
716 /* digital I/O subdevice */
717 s->type = COMEDI_SUBD_DIO;
718 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
722 s->private = &dio_private_B;
723 s->range_table = &range_digital;
724 s->insn_config = s626_dio_insn_config;
725 s->insn_bits = s626_dio_insn_bits;
727 s = dev->subdevices + 4;
728 /* digital I/O subdevice */
729 s->type = COMEDI_SUBD_DIO;
730 s->subdev_flags = SDF_WRITABLE | SDF_READABLE;
734 s->private = &dio_private_C;
735 s->range_table = &range_digital;
736 s->insn_config = s626_dio_insn_config;
737 s->insn_bits = s626_dio_insn_bits;
739 s = dev->subdevices + 5;
740 /* encoder (counter) subdevice */
741 s->type = COMEDI_SUBD_COUNTER;
742 s->subdev_flags = SDF_WRITABLE | SDF_READABLE | SDF_LSAMPL;
743 s->n_chan = thisboard->enc_chans;
744 s->private = enc_private_data;
745 s->insn_config = s626_enc_insn_config;
746 s->insn_read = s626_enc_insn_read;
747 s->insn_write = s626_enc_insn_write;
748 s->maxdata = 0xffffff;
749 s->range_table = &range_unknown;
751 /* stop ai_command */
752 devpriv->ai_cmd_running = 0;
754 if (devpriv->base_addr && (devpriv->allocatedBuf == 2)) {
758 /* enab DEBI and audio pins, enable I2C interface. */
759 MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C);
760 /* Configure DEBI operating mode. */
761 WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 /* Local bus is 16 */
763 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT)
766 /* transfer timeout */
768 |DEBI_SWAP /* Set up byte lane */
770 | DEBI_CFG_INTEL); /* Intel-compatible */
771 /* local bus (DEBI */
772 /* never times out). */
773 DEBUG("s626_attach: %d debi init -- %d\n",
774 DEBI_CFG_SLAVE16 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT) |
775 DEBI_SWAP | DEBI_CFG_INTEL,
776 DEBI_CFG_INTEL | DEBI_CFG_TOQ | DEBI_CFG_INCQ |
779 /* DEBI INIT S626 WR7146( P_DEBICFG, DEBI_CFG_INTEL | DEBI_CFG_TOQ */
780 /* | DEBI_CFG_INCQ| DEBI_CFG_16Q); //end */
782 /* Paging is disabled. */
783 WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE); /* Disable MMU paging. */
785 /* Init GPIO so that ADC Start* is negated. */
786 WR7146(P_GPIO, GPIO_BASE | GPIO1_HI);
788 /* IsBoardRevA is a boolean that indicates whether the board is RevA.
790 * VERSION 2.01 CHANGE: REV A & B BOARDS NOW SUPPORTED BY DYNAMIC
791 * EEPROM ADDRESS SELECTION. Initialize the I2C interface, which
792 * is used to access the onboard serial EEPROM. The EEPROM's I2C
793 * DeviceAddress is hardwired to a value that is dependent on the
794 * 626 board revision. On all board revisions, the EEPROM stores
795 * TrimDAC calibration constants for analog I/O. On RevB and
796 * higher boards, the DeviceAddress is hardwired to 0 to enable
797 * the EEPROM to also store the PCI SubVendorID and SubDeviceID;
798 * this is the address at which the SAA7146 expects a
799 * configuration EEPROM to reside. On RevA boards, the EEPROM
800 * device address, which is hardwired to 4, prevents the SAA7146
801 * from retrieving PCI sub-IDs, so the SAA7146 uses its built-in
802 * default values, instead.
805 /* devpriv->I2Cards= IsBoardRevA ? 0xA8 : 0xA0; // Set I2C EEPROM */
806 /* DeviceType (0xA0) */
807 /* and DeviceAddress<<1. */
809 devpriv->I2CAdrs = 0xA0; /* I2C device address for onboard */
812 /* Issue an I2C ABORT command to halt any I2C operation in */
813 /* progress and reset BUSY flag. */
814 WR7146(P_I2CSTAT, I2C_CLKSEL | I2C_ABORT);
815 /* Write I2C control: abort any I2C activity. */
816 MC_ENABLE(P_MC2, MC2_UPLD_IIC);
817 /* Invoke command upload */
818 while ((RR7146(P_MC2) & MC2_UPLD_IIC) == 0)
820 /* and wait for upload to complete. */
822 /* Per SAA7146 data sheet, write to STATUS reg twice to
823 * reset all I2C error flags. */
824 for (i = 0; i < 2; i++) {
825 WR7146(P_I2CSTAT, I2C_CLKSEL);
826 /* Write I2C control: reset error flags. */
827 MC_ENABLE(P_MC2, MC2_UPLD_IIC); /* Invoke command upload */
828 while (!MC_TEST(P_MC2, MC2_UPLD_IIC))
830 /* and wait for upload to complete. */
833 /* Init audio interface functional attributes: set DAC/ADC
834 * serial clock rates, invert DAC serial clock so that
835 * DAC data setup times are satisfied, enable DAC serial
839 WR7146(P_ACON2, ACON2_INIT);
841 /* Set up TSL1 slot list, which is used to control the
842 * accumulation of ADC data: RSD1 = shift data in on SD1.
843 * SIB_A1 = store data uint8_t at next available location in
844 * FB BUFFER1 register. */
845 WR7146(P_TSL1, RSD1 | SIB_A1);
846 /* Fetch ADC high data uint8_t. */
847 WR7146(P_TSL1 + 4, RSD1 | SIB_A1 | EOS);
848 /* Fetch ADC low data uint8_t; end of TSL1. */
850 /* enab TSL1 slot list so that it executes all the time. */
851 WR7146(P_ACON1, ACON1_ADCSTART);
853 /* Initialize RPS registers used for ADC. */
855 /* Physical start of RPS program. */
856 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase);
858 WR7146(P_RPSPAGE1, 0);
859 /* RPS program performs no explicit mem writes. */
860 WR7146(P_RPS1_TOUT, 0); /* Disable RPS timeouts. */
862 /* SAA7146 BUG WORKAROUND. Initialize SAA7146 ADC interface
863 * to a known state by invoking ADCs until FB BUFFER 1
864 * register shows that it is correctly receiving ADC data.
865 * This is necessary because the SAA7146 ADC interface does
866 * not start up in a defined state after a PCI reset.
869 /* PollList = EOPL; // Create a simple polling */
870 /* // list for analog input */
872 /* ResetADC( dev, &PollList ); */
874 /* s626_ai_rinsn(dev,dev->subdevices,NULL,data); //( &AdcData ); // */
875 /* //Get initial ADC */
878 /* StartVal = data[0]; */
880 /* // VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED EXECUTION. */
881 /* // Invoke ADCs until the new ADC value differs from the initial */
882 /* // value or a timeout occurs. The timeout protects against the */
883 /* // possibility that the driver is restarting and the ADC data is a */
884 /* // fixed value resulting from the applied ADC analog input being */
885 /* // unusually quiet or at the rail. */
887 /* for ( index = 0; index < 500; index++ ) */
889 /* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */
890 /* AdcData = data[0]; //ReadADC( &AdcData ); */
891 /* if ( AdcData != StartVal ) */
897 /* init the DAC interface */
899 /* Init Audio2's output DMAC attributes: burst length = 1
900 * DWORD, threshold = 1 DWORD.
902 WR7146(P_PCI_BT_A, 0);
904 /* Init Audio2's output DMA physical addresses. The protection
905 * address is set to 1 DWORD past the base address so that a
906 * single DWORD will be transferred each time a DMA transfer is
910 devpriv->ANABuf.PhysicalBase +
911 (DAC_WDMABUF_OS * sizeof(uint32_t));
913 WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf); /* Buffer base adrs. */
914 WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t))); /* Protection address. */
916 /* Cache Audio2's output DMA buffer logical address. This is
917 * where DAC data is buffered for A2 output DMA transfers. */
919 (uint32_t *) devpriv->ANABuf.LogicalBase + DAC_WDMABUF_OS;
921 /* Audio2's output channels does not use paging. The protection
922 * violation handling bit is set so that the DMAC will
923 * automatically halt and its PCI address pointer will be reset
924 * when the protection address is reached. */
926 WR7146(P_PAGEA2_OUT, 8);
928 /* Initialize time slot list 2 (TSL2), which is used to control
929 * the clock generation for and serialization of data to be sent
930 * to the DAC devices. Slot 0 is a NOP that is used to trap TSL
931 * execution; this permits other slots to be safely modified
932 * without first turning off the TSL sequencer (which is
933 * apparently impossible to do). Also, SD3 (which is driven by a
934 * pull-up resistor) is shifted in and stored to the MSB of
935 * FB_BUFFER2 to be used as evidence that the slot sequence has
936 * not yet finished executing.
939 SETVECT(0, XSD2 | RSD3 | SIB_A2 | EOS);
940 /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2. */
942 /* Initialize slot 1, which is constant. Slot 1 causes a
943 * DWORD to be transferred from audio channel 2's output FIFO
944 * to the FIFO's output buffer so that it can be serialized
945 * and sent to the DAC during subsequent slots. All remaining
946 * slots are dynamically populated as required by the target
950 /* Slot 1: Fetch DWORD from Audio2's output FIFO. */
952 /* Start DAC's audio interface (TSL2) running. */
953 WR7146(P_ACON1, ACON1_DACSTART);
955 /* end init DAC interface */
957 /* Init Trim DACs to calibrated values. Do it twice because the
958 * SAA7146 audio channel does not always reset properly and
959 * sometimes causes the first few TrimDAC writes to malfunction.
963 LoadTrimDACs(dev); /* Insurance. */
965 /* Manually init all gate array hardware in case this is a soft
966 * reset (we have no way of determining whether this is a warm
967 * or cold start). This is necessary because the gate array will
968 * reset only in response to a PCI hard reset; there is no soft
971 /* Init all DAC outputs to 0V and init all DAC setpoint and
974 for (chan = 0; chan < S626_DAC_CHANNELS; chan++)
975 SetDAC(dev, chan, 0);
977 /* Init image of WRMISC2 Battery Charger Enabled control bit.
978 * This image is used when the state of the charger control bit,
979 * which has no direct hardware readback mechanism, is queried.
981 devpriv->ChargeEnabled = 0;
983 /* Init image of watchdog timer interval in WRMISC2. This image
984 * maintains the value of the control bits of MISC2 are
985 * continuously reset to zero as long as the WD timer is disabled.
987 devpriv->WDInterval = 0;
989 /* Init Counter Interrupt enab mask for RDMISC2. This mask is
990 * applied against MISC2 when testing to determine which timer
991 * events are requesting interrupt service.
993 devpriv->CounterIntEnabs = 0;
998 /* Without modifying the state of the Battery Backup enab, disable
999 * the watchdog timer, set DIO channels 0-5 to operate in the
1000 * standard DIO (vs. counter overflow) mode, disable the battery
1001 * charger, and reset the watchdog interval selector to zero.
1003 WriteMISC2(dev, (uint16_t) (DEBIread(dev,
1005 MISC2_BATT_ENABLE));
1007 /* Initialize the digital I/O subsystem. */
1010 /* enable interrupt test */
1011 /* writel(IRQ_GPIO3 | IRQ_RPS1,devpriv->base_addr+P_IER); */
1014 DEBUG("s626_attach: comedi%d s626 attached %04x\n", dev->minor,
1015 (uint32_t) devpriv->base_addr);
1020 static unsigned int s626_ai_reg_to_uint(int data)
1022 unsigned int tempdata;
1024 tempdata = (data >> 18);
1025 if (tempdata & 0x2000)
1028 tempdata += (1 << 13);
1033 /* static unsigned int s626_uint_to_reg(struct comedi_subdevice *s, int data){ */
1037 static irqreturn_t s626_irq_handler(int irq, void *d)
1039 struct comedi_device *dev = d;
1040 struct comedi_subdevice *s;
1041 struct comedi_cmd *cmd;
1042 struct enc_private *k;
1043 unsigned long flags;
1045 uint32_t irqtype, irqstatus;
1051 DEBUG("s626_irq_handler: interrupt request received!!!\n");
1053 if (dev->attached == 0)
1055 /* lock to avoid race with comedi_poll */
1056 spin_lock_irqsave(&dev->spinlock, flags);
1058 /* save interrupt enable register state */
1059 irqstatus = readl(devpriv->base_addr + P_IER);
1061 /* read interrupt type */
1062 irqtype = readl(devpriv->base_addr + P_ISR);
1064 /* disable master interrupt */
1065 writel(0, devpriv->base_addr + P_IER);
1067 /* clear interrupt */
1068 writel(irqtype, devpriv->base_addr + P_ISR);
1071 DEBUG("s626_irq_handler: interrupt type %d\n", irqtype);
1074 case IRQ_RPS1: /* end_of_scan occurs */
1076 DEBUG("s626_irq_handler: RPS1 irq detected\n");
1078 /* manage ai subdevice */
1079 s = dev->subdevices;
1080 cmd = &(s->async->cmd);
1082 /* Init ptr to DMA buffer that holds new ADC data. We skip the
1083 * first uint16_t in the buffer because it contains junk data from
1084 * the final ADC of the previous poll list scan.
1086 readaddr = (int32_t *) devpriv->ANABuf.LogicalBase + 1;
1088 /* get the data and hand it over to comedi */
1089 for (i = 0; i < (s->async->cmd.chanlist_len); i++) {
1090 /* Convert ADC data to 16-bit integer values and copy to application */
1092 tempdata = s626_ai_reg_to_uint((int)*readaddr);
1095 /* put data into read buffer */
1096 /* comedi_buf_put(s->async, tempdata); */
1097 if (cfc_write_to_buffer(s, tempdata) == 0)
1099 ("s626_irq_handler: cfc_write_to_buffer error!\n");
1101 DEBUG("s626_irq_handler: ai channel %d acquired: %d\n",
1105 /* end of scan occurs */
1106 s->async->events |= COMEDI_CB_EOS;
1108 if (!(devpriv->ai_continous))
1109 devpriv->ai_sample_count--;
1110 if (devpriv->ai_sample_count <= 0) {
1111 devpriv->ai_cmd_running = 0;
1113 /* Stop RPS program. */
1114 MC_DISABLE(P_MC1, MC1_ERPS1);
1116 /* send end of acquisition */
1117 s->async->events |= COMEDI_CB_EOA;
1119 /* disable master interrupt */
1123 if (devpriv->ai_cmd_running && cmd->scan_begin_src == TRIG_EXT) {
1125 ("s626_irq_handler: enable interrupt on dio channel %d\n",
1126 cmd->scan_begin_arg);
1128 s626_dio_set_irq(dev, cmd->scan_begin_arg);
1130 DEBUG("s626_irq_handler: External trigger is set!!!\n");
1132 /* tell comedi that data is there */
1133 DEBUG("s626_irq_handler: events %d\n", s->async->events);
1134 comedi_event(dev, s);
1136 case IRQ_GPIO3: /* check dio and conter interrupt */
1138 DEBUG("s626_irq_handler: GPIO3 irq detected\n");
1140 /* manage ai subdevice */
1141 s = dev->subdevices;
1142 cmd = &(s->async->cmd);
1144 /* s626_dio_clear_irq(dev); */
1146 for (group = 0; group < S626_DIO_BANKS; group++) {
1148 /* read interrupt type */
1149 irqbit = DEBIread(dev,
1150 ((struct dio_private *)(dev->
1154 private)->RDCapFlg);
1156 /* check if interrupt is generated from dio channels */
1158 s626_dio_reset_irq(dev, group, irqbit);
1160 ("s626_irq_handler: check interrupt on dio group %d %d\n",
1162 if (devpriv->ai_cmd_running) {
1163 /* check if interrupt is an ai acquisition start trigger */
1164 if ((irqbit >> (cmd->start_arg -
1166 == 1 && cmd->start_src == TRIG_EXT) {
1168 ("s626_irq_handler: Edge capture interrupt received from channel %d\n",
1171 /* Start executing the RPS program. */
1172 MC_ENABLE(P_MC1, MC1_ERPS1);
1175 ("s626_irq_handler: acquisition start triggered!!!\n");
1177 if (cmd->scan_begin_src ==
1180 ("s626_ai_cmd: enable interrupt on dio channel %d\n",
1184 s626_dio_set_irq(dev,
1185 cmd->scan_begin_arg);
1188 ("s626_irq_handler: External scan trigger is set!!!\n");
1191 if ((irqbit >> (cmd->scan_begin_arg -
1194 && cmd->scan_begin_src ==
1197 ("s626_irq_handler: Edge capture interrupt received from channel %d\n",
1198 cmd->scan_begin_arg);
1200 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1201 MC_ENABLE(P_MC2, MC2_ADC_RPS);
1204 ("s626_irq_handler: scan triggered!!! %d\n",
1205 devpriv->ai_sample_count);
1206 if (cmd->convert_src ==
1210 ("s626_ai_cmd: enable interrupt on dio channel %d group %d\n",
1215 devpriv->ai_convert_count
1216 = cmd->chanlist_len;
1218 s626_dio_set_irq(dev,
1222 ("s626_irq_handler: External convert trigger is set!!!\n");
1225 if (cmd->convert_src ==
1228 devpriv->ai_convert_count
1229 = cmd->chanlist_len;
1230 k->SetEnable(dev, k,
1234 if ((irqbit >> (cmd->convert_arg -
1237 && cmd->convert_src == TRIG_EXT) {
1239 ("s626_irq_handler: Edge capture interrupt received from channel %d\n",
1242 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1243 MC_ENABLE(P_MC2, MC2_ADC_RPS);
1246 ("s626_irq_handler: adc convert triggered!!!\n");
1248 devpriv->ai_convert_count--;
1250 if (devpriv->ai_convert_count >
1254 ("s626_ai_cmd: enable interrupt on dio channel %d group %d\n",
1259 s626_dio_set_irq(dev,
1263 ("s626_irq_handler: External trigger is set!!!\n");
1271 /* read interrupt type */
1272 irqbit = DEBIread(dev, LP_RDMISC2);
1274 /* check interrupt on counters */
1275 DEBUG("s626_irq_handler: check counters interrupt %d\n",
1278 if (irqbit & IRQ_COINT1A) {
1280 ("s626_irq_handler: interrupt on counter 1A overflow\n");
1283 /* clear interrupt capture flag */
1284 k->ResetCapFlags(dev, k);
1286 if (irqbit & IRQ_COINT2A) {
1288 ("s626_irq_handler: interrupt on counter 2A overflow\n");
1291 /* clear interrupt capture flag */
1292 k->ResetCapFlags(dev, k);
1294 if (irqbit & IRQ_COINT3A) {
1296 ("s626_irq_handler: interrupt on counter 3A overflow\n");
1299 /* clear interrupt capture flag */
1300 k->ResetCapFlags(dev, k);
1302 if (irqbit & IRQ_COINT1B) {
1304 ("s626_irq_handler: interrupt on counter 1B overflow\n");
1307 /* clear interrupt capture flag */
1308 k->ResetCapFlags(dev, k);
1310 if (irqbit & IRQ_COINT2B) {
1312 ("s626_irq_handler: interrupt on counter 2B overflow\n");
1315 /* clear interrupt capture flag */
1316 k->ResetCapFlags(dev, k);
1318 if (devpriv->ai_convert_count > 0) {
1319 devpriv->ai_convert_count--;
1320 if (devpriv->ai_convert_count == 0)
1321 k->SetEnable(dev, k, CLKENAB_INDEX);
1323 if (cmd->convert_src == TRIG_TIMER) {
1325 ("s626_irq_handler: conver timer trigger!!! %d\n",
1326 devpriv->ai_convert_count);
1328 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1329 MC_ENABLE(P_MC2, MC2_ADC_RPS);
1333 if (irqbit & IRQ_COINT3B) {
1335 ("s626_irq_handler: interrupt on counter 3B overflow\n");
1338 /* clear interrupt capture flag */
1339 k->ResetCapFlags(dev, k);
1341 if (cmd->scan_begin_src == TRIG_TIMER) {
1343 ("s626_irq_handler: scan timer trigger!!!\n");
1345 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1346 MC_ENABLE(P_MC2, MC2_ADC_RPS);
1349 if (cmd->convert_src == TRIG_TIMER) {
1351 ("s626_irq_handler: convert timer trigger is set\n");
1353 devpriv->ai_convert_count = cmd->chanlist_len;
1354 k->SetEnable(dev, k, CLKENAB_ALWAYS);
1359 /* enable interrupt */
1360 writel(irqstatus, devpriv->base_addr + P_IER);
1362 DEBUG("s626_irq_handler: exit interrupt service routine.\n");
1364 spin_unlock_irqrestore(&dev->spinlock, flags);
1368 static int s626_detach(struct comedi_device *dev)
1371 /* stop ai_command */
1372 devpriv->ai_cmd_running = 0;
1374 if (devpriv->base_addr) {
1375 /* interrupt mask */
1376 WR7146(P_IER, 0); /* Disable master interrupt. */
1377 WR7146(P_ISR, IRQ_GPIO3 | IRQ_RPS1); /* Clear board's IRQ status flag. */
1379 /* Disable the watchdog timer and battery charger. */
1382 /* Close all interfaces on 7146 device. */
1383 WR7146(P_MC1, MC1_SHUTDOWN);
1384 WR7146(P_ACON1, ACON1_BASE);
1386 CloseDMAB(dev, &devpriv->RPSBuf, DMABUF_SIZE);
1387 CloseDMAB(dev, &devpriv->ANABuf, DMABUF_SIZE);
1391 free_irq(dev->irq, dev);
1393 if (devpriv->base_addr)
1394 iounmap(devpriv->base_addr);
1396 if (devpriv->pdev) {
1397 if (devpriv->got_regions)
1398 comedi_pci_disable(devpriv->pdev);
1399 pci_dev_put(devpriv->pdev);
1403 DEBUG("s626_detach: S626 detached!\n");
1409 * this functions build the RPS program for hardware driven acquistion
1411 void ResetADC(struct comedi_device *dev, uint8_t * ppl)
1413 register uint32_t *pRPS;
1418 struct comedi_cmd *cmd = &(dev->subdevices->async->cmd);
1420 /* Stop RPS program in case it is currently running. */
1421 MC_DISABLE(P_MC1, MC1_ERPS1);
1423 /* Set starting logical address to write RPS commands. */
1424 pRPS = (uint32_t *) devpriv->RPSBuf.LogicalBase;
1426 /* Initialize RPS instruction pointer. */
1427 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase);
1429 /* Construct RPS program in RPSBuf DMA buffer */
1431 if (cmd != NULL && cmd->scan_begin_src != TRIG_FOLLOW) {
1432 DEBUG("ResetADC: scan_begin pause inserted\n");
1433 /* Wait for Start trigger. */
1434 *pRPS++ = RPS_PAUSE | RPS_SIGADC;
1435 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC;
1438 /* SAA7146 BUG WORKAROUND Do a dummy DEBI Write. This is necessary
1439 * because the first RPS DEBI Write following a non-RPS DEBI write
1440 * seems to always fail. If we don't do this dummy write, the ADC
1441 * gain might not be set to the value required for the first slot in
1442 * the poll list; the ADC gain would instead remain unchanged from
1443 * the previously programmed value.
1445 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2);
1446 /* Write DEBI Write command and address to shadow RAM. */
1448 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL;
1449 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2);
1450 /* Write DEBI immediate data to shadow RAM: */
1452 *pRPS++ = GSEL_BIPOLAR5V;
1453 /* arbitrary immediate data value. */
1455 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI;
1456 /* Reset "shadow RAM uploaded" flag. */
1457 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */
1458 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to finish. */
1460 /* Digitize all slots in the poll list. This is implemented as a
1461 * for loop to limit the slot count to 16 in case the application
1462 * forgot to set the EOPL flag in the final slot.
1464 for (devpriv->AdcItems = 0; devpriv->AdcItems < 16; devpriv->AdcItems++) {
1465 /* Convert application's poll list item to private board class
1466 * format. Each app poll list item is an uint8_t with form
1467 * (EOPL,x,x,RANGE,CHAN<3:0>), where RANGE code indicates 0 =
1468 * +-10V, 1 = +-5V, and EOPL = End of Poll List marker.
1471 (*ppl << 8) | (*ppl & 0x10 ? GSEL_BIPOLAR5V :
1474 /* Switch ADC analog gain. */
1475 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); /* Write DEBI command */
1476 /* and address to */
1478 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL;
1479 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); /* Write DEBI */
1480 /* immediate data to */
1483 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; /* Reset "shadow RAM uploaded" */
1485 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */
1486 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to */
1489 /* Select ADC analog input channel. */
1490 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2);
1491 /* Write DEBI command and address to shadow RAM. */
1492 *pRPS++ = DEBI_CMD_WRWORD | LP_ISEL;
1493 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2);
1494 /* Write DEBI immediate data to shadow RAM. */
1496 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI;
1497 /* Reset "shadow RAM uploaded" flag. */
1499 *pRPS++ = RPS_UPLOAD | RPS_DEBI;
1500 /* Invoke shadow RAM upload. */
1502 *pRPS++ = RPS_PAUSE | RPS_DEBI;
1503 /* Wait for shadow upload to finish. */
1505 /* Delay at least 10 microseconds for analog input settling.
1506 * Instead of padding with NOPs, we use RPS_JUMP instructions
1507 * here; this allows us to produce a longer delay than is
1508 * possible with NOPs because each RPS_JUMP flushes the RPS'
1509 * instruction prefetch pipeline.
1512 (uint32_t) devpriv->RPSBuf.PhysicalBase +
1513 (uint32_t) ((unsigned long)pRPS -
1514 (unsigned long)devpriv->RPSBuf.LogicalBase);
1515 for (i = 0; i < (10 * RPSCLK_PER_US / 2); i++) {
1516 JmpAdrs += 8; /* Repeat to implement time delay: */
1517 *pRPS++ = RPS_JUMP; /* Jump to next RPS instruction. */
1521 if (cmd != NULL && cmd->convert_src != TRIG_NOW) {
1522 DEBUG("ResetADC: convert pause inserted\n");
1523 /* Wait for Start trigger. */
1524 *pRPS++ = RPS_PAUSE | RPS_SIGADC;
1525 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC;
1527 /* Start ADC by pulsing GPIO1. */
1528 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */
1529 *pRPS++ = GPIO_BASE | GPIO1_LO;
1531 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */
1532 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */
1533 *pRPS++ = GPIO_BASE | GPIO1_HI;
1535 /* Wait for ADC to complete (GPIO2 is asserted high when ADC not
1536 * busy) and for data from previous conversion to shift into FB
1537 * BUFFER 1 register.
1539 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */
1541 /* Transfer ADC data from FB BUFFER 1 register to DMA buffer. */
1542 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2);
1544 (uint32_t) devpriv->ANABuf.PhysicalBase +
1545 (devpriv->AdcItems << 2);
1547 /* If this slot's EndOfPollList flag is set, all channels have */
1548 /* now been processed. */
1549 if (*ppl++ & EOPL) {
1550 devpriv->AdcItems++; /* Adjust poll list item count. */
1551 break; /* Exit poll list processing loop. */
1554 DEBUG("ResetADC: ADC items %d\n", devpriv->AdcItems);
1556 /* VERSION 2.01 CHANGE: DELAY CHANGED FROM 250NS to 2US. Allow the
1557 * ADC to stabilize for 2 microseconds before starting the final
1558 * (dummy) conversion. This delay is necessary to allow sufficient
1559 * time between last conversion finished and the start of the dummy
1560 * conversion. Without this delay, the last conversion's data value
1561 * is sometimes set to the previous conversion's data value.
1563 for (n = 0; n < (2 * RPSCLK_PER_US); n++)
1566 /* Start a dummy conversion to cause the data from the last
1567 * conversion of interest to be shifted in.
1569 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */
1570 *pRPS++ = GPIO_BASE | GPIO1_LO;
1572 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */
1573 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */
1574 *pRPS++ = GPIO_BASE | GPIO1_HI;
1576 /* Wait for the data from the last conversion of interest to arrive
1577 * in FB BUFFER 1 register.
1579 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */
1581 /* Transfer final ADC data from FB BUFFER 1 register to DMA buffer. */
1582 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2); /* */
1584 (uint32_t) devpriv->ANABuf.PhysicalBase + (devpriv->AdcItems << 2);
1586 /* Indicate ADC scan loop is finished. */
1587 /* *pRPS++= RPS_CLRSIGNAL | RPS_SIGADC ; // Signal ReadADC() that scan is done. */
1589 /* invoke interrupt */
1590 if (devpriv->ai_cmd_running == 1) {
1591 DEBUG("ResetADC: insert irq in ADC RPS task\n");
1594 /* Restart RPS program at its beginning. */
1595 *pRPS++ = RPS_JUMP; /* Branch to start of RPS program. */
1596 *pRPS++ = (uint32_t) devpriv->RPSBuf.PhysicalBase;
1598 /* End of RPS program build */
1601 /* TO COMPLETE, IF NECESSARY */
1602 static int s626_ai_insn_config(struct comedi_device *dev,
1603 struct comedi_subdevice *s,
1604 struct comedi_insn *insn, unsigned int *data)
1610 /* static int s626_ai_rinsn(struct comedi_device *dev,struct comedi_subdevice *s,struct comedi_insn *insn,unsigned int *data) */
1612 /* register uint8_t i; */
1613 /* register int32_t *readaddr; */
1615 /* DEBUG("as626_ai_rinsn: ai_rinsn enter\n"); */
1617 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1618 /* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */
1620 /* Wait until ADC scan loop is finished (RPS Signal 0 reset). */
1621 /* while ( MC_TEST( P_MC2, MC2_ADC_RPS ) ); */
1623 /* Init ptr to DMA buffer that holds new ADC data. We skip the
1624 * first uint16_t in the buffer because it contains junk data from
1625 * the final ADC of the previous poll list scan.
1627 /* readaddr = (uint32_t *)devpriv->ANABuf.LogicalBase + 1; */
1629 /* Convert ADC data to 16-bit integer values and copy to application buffer. */
1630 /* for ( i = 0; i < devpriv->AdcItems; i++ ) { */
1631 /* *data = s626_ai_reg_to_uint( *readaddr++ ); */
1632 /* DEBUG("s626_ai_rinsn: data %d\n",*data); */
1636 /* DEBUG("s626_ai_rinsn: ai_rinsn escape\n"); */
1640 static int s626_ai_insn_read(struct comedi_device *dev,
1641 struct comedi_subdevice *s,
1642 struct comedi_insn *insn, unsigned int *data)
1644 uint16_t chan = CR_CHAN(insn->chanspec);
1645 uint16_t range = CR_RANGE(insn->chanspec);
1646 uint16_t AdcSpec = 0;
1650 /* interrupt call test */
1651 /* writel(IRQ_GPIO3,devpriv->base_addr+P_PSR); */
1652 /* Writing a logical 1 into any of the RPS_PSR bits causes the
1653 * corresponding interrupt to be generated if enabled
1656 DEBUG("s626_ai_insn_read: entering\n");
1658 /* Convert application's ADC specification into form
1659 * appropriate for register programming.
1662 AdcSpec = (chan << 8) | (GSEL_BIPOLAR5V);
1664 AdcSpec = (chan << 8) | (GSEL_BIPOLAR10V);
1666 /* Switch ADC analog gain. */
1667 DEBIwrite(dev, LP_GSEL, AdcSpec); /* Set gain. */
1669 /* Select ADC analog input channel. */
1670 DEBIwrite(dev, LP_ISEL, AdcSpec); /* Select channel. */
1672 for (n = 0; n < insn->n; n++) {
1674 /* Delay 10 microseconds for analog input settling. */
1677 /* Start ADC by pulsing GPIO1 low. */
1678 GpioImage = RR7146(P_GPIO);
1679 /* Assert ADC Start command */
1680 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1681 /* and stretch it out. */
1682 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1683 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1684 /* Negate ADC Start command. */
1685 WR7146(P_GPIO, GpioImage | GPIO1_HI);
1687 /* Wait for ADC to complete (GPIO2 is asserted high when */
1688 /* ADC not busy) and for data from previous conversion to */
1689 /* shift into FB BUFFER 1 register. */
1691 /* Wait for ADC done. */
1692 while (!(RR7146(P_PSR) & PSR_GPIO2))
1695 /* Fetch ADC data. */
1697 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1));
1699 /* Allow the ADC to stabilize for 4 microseconds before
1700 * starting the next (final) conversion. This delay is
1701 * necessary to allow sufficient time between last
1702 * conversion finished and the start of the next
1703 * conversion. Without this delay, the last conversion's
1704 * data value is sometimes set to the previous
1705 * conversion's data value.
1710 /* Start a dummy conversion to cause the data from the
1711 * previous conversion to be shifted in. */
1712 GpioImage = RR7146(P_GPIO);
1714 /* Assert ADC Start command */
1715 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1716 /* and stretch it out. */
1717 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1718 WR7146(P_GPIO, GpioImage & ~GPIO1_HI);
1719 /* Negate ADC Start command. */
1720 WR7146(P_GPIO, GpioImage | GPIO1_HI);
1722 /* Wait for the data to arrive in FB BUFFER 1 register. */
1724 /* Wait for ADC done. */
1725 while (!(RR7146(P_PSR) & PSR_GPIO2))
1728 /* Fetch ADC data from audio interface's input shift register. */
1730 /* Fetch ADC data. */
1732 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1));
1734 DEBUG("s626_ai_insn_read: samples %d, data %d\n", n, data[n - 1]);
1739 static int s626_ai_load_polllist(uint8_t *ppl, struct comedi_cmd *cmd)
1744 for (n = 0; n < cmd->chanlist_len; n++) {
1745 if (CR_RANGE((cmd->chanlist)[n]) == 0)
1746 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_5V);
1748 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_10V);
1756 static int s626_ai_inttrig(struct comedi_device *dev,
1757 struct comedi_subdevice *s, unsigned int trignum)
1762 DEBUG("s626_ai_inttrig: trigger adc start...");
1764 /* Start executing the RPS program. */
1765 MC_ENABLE(P_MC1, MC1_ERPS1);
1767 s->async->inttrig = NULL;
1775 static int s626_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
1779 struct comedi_cmd *cmd = &s->async->cmd;
1780 struct enc_private *k;
1783 DEBUG("s626_ai_cmd: entering command function\n");
1785 if (devpriv->ai_cmd_running) {
1786 printk(KERN_ERR "s626_ai_cmd: Another ai_cmd is running %d\n",
1790 /* disable interrupt */
1791 writel(0, devpriv->base_addr + P_IER);
1793 /* clear interrupt request */
1794 writel(IRQ_RPS1 | IRQ_GPIO3, devpriv->base_addr + P_ISR);
1796 /* clear any pending interrupt */
1797 s626_dio_clear_irq(dev);
1798 /* s626_enc_clear_irq(dev); */
1800 /* reset ai_cmd_running flag */
1801 devpriv->ai_cmd_running = 0;
1803 /* test if cmd is valid */
1805 DEBUG("s626_ai_cmd: NULL command\n");
1808 DEBUG("s626_ai_cmd: command received!!!\n");
1811 if (dev->irq == 0) {
1813 "s626_ai_cmd: cannot run command without an irq");
1817 s626_ai_load_polllist(ppl, cmd);
1818 devpriv->ai_cmd_running = 1;
1819 devpriv->ai_convert_count = 0;
1821 switch (cmd->scan_begin_src) {
1825 /* set a conter to generate adc trigger at scan_begin_arg interval */
1827 tick = s626_ns_to_timer((int *)&cmd->scan_begin_arg,
1828 cmd->flags & TRIG_ROUND_MASK);
1830 /* load timer value and enable interrupt */
1831 s626_timer_load(dev, k, tick);
1832 k->SetEnable(dev, k, CLKENAB_ALWAYS);
1834 DEBUG("s626_ai_cmd: scan trigger timer is set with value %d\n",
1839 /* set the digital line and interrupt for scan trigger */
1840 if (cmd->start_src != TRIG_EXT)
1841 s626_dio_set_irq(dev, cmd->scan_begin_arg);
1843 DEBUG("s626_ai_cmd: External scan trigger is set!!!\n");
1848 switch (cmd->convert_src) {
1852 /* set a conter to generate adc trigger at convert_arg interval */
1854 tick = s626_ns_to_timer((int *)&cmd->convert_arg,
1855 cmd->flags & TRIG_ROUND_MASK);
1857 /* load timer value and enable interrupt */
1858 s626_timer_load(dev, k, tick);
1859 k->SetEnable(dev, k, CLKENAB_INDEX);
1862 ("s626_ai_cmd: convert trigger timer is set with value %d\n",
1866 /* set the digital line and interrupt for convert trigger */
1867 if (cmd->scan_begin_src != TRIG_EXT
1868 && cmd->start_src == TRIG_EXT)
1869 s626_dio_set_irq(dev, cmd->convert_arg);
1871 DEBUG("s626_ai_cmd: External convert trigger is set!!!\n");
1876 switch (cmd->stop_src) {
1878 /* data arrives as one packet */
1879 devpriv->ai_sample_count = cmd->stop_arg;
1880 devpriv->ai_continous = 0;
1883 /* continous acquisition */
1884 devpriv->ai_continous = 1;
1885 devpriv->ai_sample_count = 0;
1891 switch (cmd->start_src) {
1893 /* Trigger ADC scan loop start by setting RPS Signal 0. */
1894 /* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */
1896 /* Start executing the RPS program. */
1897 MC_ENABLE(P_MC1, MC1_ERPS1);
1899 DEBUG("s626_ai_cmd: ADC triggered\n");
1900 s->async->inttrig = NULL;
1903 /* configure DIO channel for acquisition trigger */
1904 s626_dio_set_irq(dev, cmd->start_arg);
1906 DEBUG("s626_ai_cmd: External start trigger is set!!!\n");
1908 s->async->inttrig = NULL;
1911 s->async->inttrig = s626_ai_inttrig;
1915 /* enable interrupt */
1916 writel(IRQ_GPIO3 | IRQ_RPS1, devpriv->base_addr + P_IER);
1918 DEBUG("s626_ai_cmd: command function terminated\n");
1923 static int s626_ai_cmdtest(struct comedi_device *dev,
1924 struct comedi_subdevice *s, struct comedi_cmd *cmd)
1929 /* cmdtest tests a particular command to see if it is valid. Using
1930 * the cmdtest ioctl, a user can create a valid cmd and then have it
1931 * executes by the cmd ioctl.
1933 * cmdtest returns 1,2,3,4 or 0, depending on which tests the
1934 * command passes. */
1936 /* step 1: make sure trigger sources are trivially valid */
1938 tmp = cmd->start_src;
1939 cmd->start_src &= TRIG_NOW | TRIG_INT | TRIG_EXT;
1940 if (!cmd->start_src || tmp != cmd->start_src)
1943 tmp = cmd->scan_begin_src;
1944 cmd->scan_begin_src &= TRIG_TIMER | TRIG_EXT | TRIG_FOLLOW;
1945 if (!cmd->scan_begin_src || tmp != cmd->scan_begin_src)
1948 tmp = cmd->convert_src;
1949 cmd->convert_src &= TRIG_TIMER | TRIG_EXT | TRIG_NOW;
1950 if (!cmd->convert_src || tmp != cmd->convert_src)
1953 tmp = cmd->scan_end_src;
1954 cmd->scan_end_src &= TRIG_COUNT;
1955 if (!cmd->scan_end_src || tmp != cmd->scan_end_src)
1958 tmp = cmd->stop_src;
1959 cmd->stop_src &= TRIG_COUNT | TRIG_NONE;
1960 if (!cmd->stop_src || tmp != cmd->stop_src)
1966 /* step 2: make sure trigger sources are unique and mutually
1969 /* note that mutual compatibility is not an issue here */
1970 if (cmd->scan_begin_src != TRIG_TIMER &&
1971 cmd->scan_begin_src != TRIG_EXT
1972 && cmd->scan_begin_src != TRIG_FOLLOW)
1974 if (cmd->convert_src != TRIG_TIMER &&
1975 cmd->convert_src != TRIG_EXT && cmd->convert_src != TRIG_NOW)
1977 if (cmd->stop_src != TRIG_COUNT && cmd->stop_src != TRIG_NONE)
1983 /* step 3: make sure arguments are trivially compatible */
1985 if (cmd->start_src != TRIG_EXT && cmd->start_arg != 0) {
1990 if (cmd->start_src == TRIG_EXT && cmd->start_arg > 39) {
1991 cmd->start_arg = 39;
1995 if (cmd->scan_begin_src == TRIG_EXT && cmd->scan_begin_arg > 39) {
1996 cmd->scan_begin_arg = 39;
2000 if (cmd->convert_src == TRIG_EXT && cmd->convert_arg > 39) {
2001 cmd->convert_arg = 39;
2004 #define MAX_SPEED 200000 /* in nanoseconds */
2005 #define MIN_SPEED 2000000000 /* in nanoseconds */
2007 if (cmd->scan_begin_src == TRIG_TIMER) {
2008 if (cmd->scan_begin_arg < MAX_SPEED) {
2009 cmd->scan_begin_arg = MAX_SPEED;
2012 if (cmd->scan_begin_arg > MIN_SPEED) {
2013 cmd->scan_begin_arg = MIN_SPEED;
2017 /* external trigger */
2018 /* should be level/edge, hi/lo specification here */
2019 /* should specify multiple external triggers */
2020 /* if(cmd->scan_begin_arg>9){ */
2021 /* cmd->scan_begin_arg=9; */
2025 if (cmd->convert_src == TRIG_TIMER) {
2026 if (cmd->convert_arg < MAX_SPEED) {
2027 cmd->convert_arg = MAX_SPEED;
2030 if (cmd->convert_arg > MIN_SPEED) {
2031 cmd->convert_arg = MIN_SPEED;
2035 /* external trigger */
2037 /* if(cmd->convert_arg>9){ */
2038 /* cmd->convert_arg=9; */
2043 if (cmd->scan_end_arg != cmd->chanlist_len) {
2044 cmd->scan_end_arg = cmd->chanlist_len;
2047 if (cmd->stop_src == TRIG_COUNT) {
2048 if (cmd->stop_arg > 0x00ffffff) {
2049 cmd->stop_arg = 0x00ffffff;
2054 if (cmd->stop_arg != 0) {
2063 /* step 4: fix up any arguments */
2065 if (cmd->scan_begin_src == TRIG_TIMER) {
2066 tmp = cmd->scan_begin_arg;
2067 s626_ns_to_timer((int *)&cmd->scan_begin_arg,
2068 cmd->flags & TRIG_ROUND_MASK);
2069 if (tmp != cmd->scan_begin_arg)
2072 if (cmd->convert_src == TRIG_TIMER) {
2073 tmp = cmd->convert_arg;
2074 s626_ns_to_timer((int *)&cmd->convert_arg,
2075 cmd->flags & TRIG_ROUND_MASK);
2076 if (tmp != cmd->convert_arg)
2078 if (cmd->scan_begin_src == TRIG_TIMER &&
2079 cmd->scan_begin_arg <
2080 cmd->convert_arg * cmd->scan_end_arg) {
2081 cmd->scan_begin_arg =
2082 cmd->convert_arg * cmd->scan_end_arg;
2093 static int s626_ai_cancel(struct comedi_device *dev, struct comedi_subdevice *s)
2095 /* Stop RPS program in case it is currently running. */
2096 MC_DISABLE(P_MC1, MC1_ERPS1);
2098 /* disable master interrupt */
2099 writel(0, devpriv->base_addr + P_IER);
2101 devpriv->ai_cmd_running = 0;
2106 /* This function doesn't require a particular form, this is just what
2107 * happens to be used in some of the drivers. It should convert ns
2108 * nanoseconds to a counter value suitable for programming the device.
2109 * Also, it should adjust ns so that it cooresponds to the actual time
2110 * that the device will use. */
2111 static int s626_ns_to_timer(int *nanosec, int round_mode)
2115 base = 500; /* 2MHz internal clock */
2117 switch (round_mode) {
2118 case TRIG_ROUND_NEAREST:
2120 divider = (*nanosec + base / 2) / base;
2122 case TRIG_ROUND_DOWN:
2123 divider = (*nanosec) / base;
2126 divider = (*nanosec + base - 1) / base;
2130 *nanosec = base * divider;
2134 static int s626_ao_winsn(struct comedi_device *dev, struct comedi_subdevice *s,
2135 struct comedi_insn *insn, unsigned int *data)
2139 uint16_t chan = CR_CHAN(insn->chanspec);
2142 for (i = 0; i < insn->n; i++) {
2143 dacdata = (int16_t) data[i];
2144 devpriv->ao_readback[CR_CHAN(insn->chanspec)] = data[i];
2145 dacdata -= (0x1fff);
2147 SetDAC(dev, chan, dacdata);
2153 static int s626_ao_rinsn(struct comedi_device *dev, struct comedi_subdevice *s,
2154 struct comedi_insn *insn, unsigned int *data)
2158 for (i = 0; i < insn->n; i++)
2159 data[i] = devpriv->ao_readback[CR_CHAN(insn->chanspec)];
2164 /* *************** DIGITAL I/O FUNCTIONS ***************
2165 * All DIO functions address a group of DIO channels by means of
2166 * "group" argument. group may be 0, 1 or 2, which correspond to DIO
2167 * ports A, B and C, respectively.
2170 static void s626_dio_init(struct comedi_device *dev)
2173 struct comedi_subdevice *s;
2175 /* Prepare to treat writes to WRCapSel as capture disables. */
2176 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP);
2178 /* For each group of sixteen channels ... */
2179 for (group = 0; group < S626_DIO_BANKS; group++) {
2180 s = dev->subdevices + 2 + group;
2181 DEBIwrite(dev, diopriv->WRIntSel, 0); /* Disable all interrupts. */
2182 DEBIwrite(dev, diopriv->WRCapSel, 0xFFFF); /* Disable all event */
2184 DEBIwrite(dev, diopriv->WREdgSel, 0); /* Init all DIOs to */
2187 DEBIwrite(dev, diopriv->WRDOut, 0); /* Program all outputs */
2188 /* to inactive state. */
2190 DEBUG("s626_dio_init: DIO initialized\n");
2193 /* DIO devices are slightly special. Although it is possible to
2194 * implement the insn_read/insn_write interface, it is much more
2195 * useful to applications if you implement the insn_bits interface.
2196 * This allows packed reading/writing of the DIO channels. The comedi
2197 * core can convert between insn_bits and insn_read/write */
2199 static int s626_dio_insn_bits(struct comedi_device *dev,
2200 struct comedi_subdevice *s,
2201 struct comedi_insn *insn, unsigned int *data)
2204 /* Length of data must be 2 (mask and new data, see below) */
2210 ("comedi%d: s626: s626_dio_insn_bits(): Invalid instruction length\n",
2216 * The insn data consists of a mask in data[0] and the new data in
2217 * data[1]. The mask defines which bits we are concerning about.
2218 * The new data must be anded with the mask. Each channel
2219 * corresponds to a bit.
2222 /* Check if requested ports are configured for output */
2223 if ((s->io_bits & data[0]) != data[0])
2226 s->state &= ~data[0];
2227 s->state |= data[0] & data[1];
2229 /* Write out the new digital output lines */
2231 DEBIwrite(dev, diopriv->WRDOut, s->state);
2233 data[1] = DEBIread(dev, diopriv->RDDIn);
2238 static int s626_dio_insn_config(struct comedi_device *dev,
2239 struct comedi_subdevice *s,
2240 struct comedi_insn *insn, unsigned int *data)
2244 case INSN_CONFIG_DIO_QUERY:
2247 io_bits & (1 << CR_CHAN(insn->chanspec))) ? COMEDI_OUTPUT :
2252 s->io_bits &= ~(1 << CR_CHAN(insn->chanspec));
2255 s->io_bits |= 1 << CR_CHAN(insn->chanspec);
2261 DEBIwrite(dev, diopriv->WRDOut, s->io_bits);
2266 static int s626_dio_set_irq(struct comedi_device *dev, unsigned int chan)
2269 unsigned int bitmask;
2270 unsigned int status;
2272 /* select dio bank */
2274 bitmask = 1 << (chan - (16 * group));
2275 DEBUG("s626_dio_set_irq: enable interrupt on dio channel %d group %d\n",
2276 chan - (16 * group), group);
2278 /* set channel to capture positive edge */
2279 status = DEBIread(dev,
2280 ((struct dio_private *)(dev->subdevices + 2 +
2281 group)->private)->RDEdgSel);
2283 ((struct dio_private *)(dev->subdevices + 2 +
2284 group)->private)->WREdgSel,
2287 /* enable interrupt on selected channel */
2288 status = DEBIread(dev,
2289 ((struct dio_private *)(dev->subdevices + 2 +
2290 group)->private)->RDIntSel);
2292 ((struct dio_private *)(dev->subdevices + 2 +
2293 group)->private)->WRIntSel,
2296 /* enable edge capture write command */
2297 DEBIwrite(dev, LP_MISC1, MISC1_EDCAP);
2299 /* enable edge capture on selected channel */
2300 status = DEBIread(dev,
2301 ((struct dio_private *)(dev->subdevices + 2 +
2302 group)->private)->RDCapSel);
2304 ((struct dio_private *)(dev->subdevices + 2 +
2305 group)->private)->WRCapSel,
2311 static int s626_dio_reset_irq(struct comedi_device *dev, unsigned int group,
2315 ("s626_dio_reset_irq: disable interrupt on dio channel %d group %d\n",
2318 /* disable edge capture write command */
2319 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP);
2321 /* enable edge capture on selected channel */
2323 ((struct dio_private *)(dev->subdevices + 2 +
2324 group)->private)->WRCapSel, mask);
2329 static int s626_dio_clear_irq(struct comedi_device *dev)
2333 /* disable edge capture write command */
2334 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP);
2336 for (group = 0; group < S626_DIO_BANKS; group++) {
2337 /* clear pending events and interrupt */
2339 ((struct dio_private *)(dev->subdevices + 2 +
2340 group)->private)->WRCapSel,
2347 /* Now this function initializes the value of the counter (data[0])
2348 and set the subdevice. To complete with trigger and interrupt
2350 static int s626_enc_insn_config(struct comedi_device *dev,
2351 struct comedi_subdevice *s,
2352 struct comedi_insn *insn, unsigned int *data)
2354 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */
2356 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */
2357 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is Counter. */
2358 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */
2359 /* ( CNTDIR_UP << BF_CLKPOL ) | // Count direction is Down. */
2360 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */
2361 (CLKENAB_INDEX << BF_CLKENAB);
2362 /* uint16_t DisableIntSrc=TRUE; */
2363 /* uint32_t Preloadvalue; //Counter initial value */
2364 uint16_t valueSrclatch = LATCHSRC_AB_READ;
2365 uint16_t enab = CLKENAB_ALWAYS;
2366 struct enc_private *k = &encpriv[CR_CHAN(insn->chanspec)];
2368 DEBUG("s626_enc_insn_config: encoder config\n");
2370 /* (data==NULL) ? (Preloadvalue=0) : (Preloadvalue=data[0]); */
2372 k->SetMode(dev, k, Setup, TRUE);
2373 Preload(dev, k, *(insn->data));
2374 k->PulseIndex(dev, k);
2375 SetLatchSource(dev, k, valueSrclatch);
2376 k->SetEnable(dev, k, (uint16_t) (enab != 0));
2381 static int s626_enc_insn_read(struct comedi_device *dev,
2382 struct comedi_subdevice *s,
2383 struct comedi_insn *insn, unsigned int *data)
2387 struct enc_private *k = &encpriv[CR_CHAN(insn->chanspec)];
2389 DEBUG("s626_enc_insn_read: encoder read channel %d\n",
2390 CR_CHAN(insn->chanspec));
2392 for (n = 0; n < insn->n; n++)
2393 data[n] = ReadLatch(dev, k);
2395 DEBUG("s626_enc_insn_read: encoder sample %d\n", data[n]);
2400 static int s626_enc_insn_write(struct comedi_device *dev,
2401 struct comedi_subdevice *s,
2402 struct comedi_insn *insn, unsigned int *data)
2405 struct enc_private *k = &encpriv[CR_CHAN(insn->chanspec)];
2407 DEBUG("s626_enc_insn_write: encoder write channel %d\n",
2408 CR_CHAN(insn->chanspec));
2410 /* Set the preload register */
2411 Preload(dev, k, data[0]);
2413 /* Software index pulse forces the preload register to load */
2414 /* into the counter */
2415 k->SetLoadTrig(dev, k, 0);
2416 k->PulseIndex(dev, k);
2417 k->SetLoadTrig(dev, k, 2);
2419 DEBUG("s626_enc_insn_write: End encoder write\n");
2424 static void s626_timer_load(struct comedi_device *dev, struct enc_private *k,
2427 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */
2429 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */
2430 (CLKSRC_TIMER << BF_CLKSRC) | /* Operating mode is Timer. */
2431 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */
2432 (CNTDIR_DOWN << BF_CLKPOL) | /* Count direction is Down. */
2433 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */
2434 (CLKENAB_INDEX << BF_CLKENAB);
2435 uint16_t valueSrclatch = LATCHSRC_A_INDXA;
2436 /* uint16_t enab=CLKENAB_ALWAYS; */
2438 k->SetMode(dev, k, Setup, FALSE);
2440 /* Set the preload register */
2441 Preload(dev, k, tick);
2443 /* Software index pulse forces the preload register to load */
2444 /* into the counter */
2445 k->SetLoadTrig(dev, k, 0);
2446 k->PulseIndex(dev, k);
2448 /* set reload on counter overflow */
2449 k->SetLoadTrig(dev, k, 1);
2451 /* set interrupt on overflow */
2452 k->SetIntSrc(dev, k, INTSRC_OVER);
2454 SetLatchSource(dev, k, valueSrclatch);
2455 /* k->SetEnable(dev,k,(uint16_t)(enab != 0)); */
2458 /* *********** DAC FUNCTIONS *********** */
2460 /* Slot 0 base settings. */
2461 #define VECT0 (XSD2 | RSD3 | SIB_A2)
2462 /* Slot 0 always shifts in 0xFF and store it to FB_BUFFER2. */
2464 /* TrimDac LogicalChan-to-PhysicalChan mapping table. */
2465 static uint8_t trimchan[] = { 10, 9, 8, 3, 2, 7, 6, 1, 0, 5, 4 };
2467 /* TrimDac LogicalChan-to-EepromAdrs mapping table. */
2468 static uint8_t trimadrs[] = { 0x40, 0x41, 0x42, 0x50, 0x51, 0x52, 0x53, 0x60, 0x61, 0x62, 0x63 };
2470 static void LoadTrimDACs(struct comedi_device *dev)
2474 /* Copy TrimDac setpoint values from EEPROM to TrimDacs. */
2475 for (i = 0; i < ARRAY_SIZE(trimchan); i++)
2476 WriteTrimDAC(dev, i, I2Cread(dev, trimadrs[i]));
2479 static void WriteTrimDAC(struct comedi_device *dev, uint8_t LogicalChan,
2484 /* Save the new setpoint in case the application needs to read it back later. */
2485 devpriv->TrimSetpoint[LogicalChan] = (uint8_t) DacData;
2487 /* Map logical channel number to physical channel number. */
2488 chan = (uint32_t) trimchan[LogicalChan];
2490 /* Set up TSL2 records for TrimDac write operation. All slots shift
2491 * 0xFF in from pulled-up SD3 so that the end of the slot sequence
2495 SETVECT(2, XSD2 | XFIFO_1 | WS3);
2496 /* Slot 2: Send high uint8_t to target TrimDac. */
2497 SETVECT(3, XSD2 | XFIFO_0 | WS3);
2498 /* Slot 3: Send low uint8_t to target TrimDac. */
2499 SETVECT(4, XSD2 | XFIFO_3 | WS1);
2500 /* Slot 4: Send NOP high uint8_t to DAC0 to keep clock running. */
2501 SETVECT(5, XSD2 | XFIFO_2 | WS1 | EOS);
2502 /* Slot 5: Send NOP low uint8_t to DAC0. */
2504 /* Construct and transmit target DAC's serial packet:
2505 * ( 0000 AAAA ), ( DDDD DDDD ),( 0x00 ),( 0x00 ) where A<3:0> is the
2506 * DAC channel's address, and D<7:0> is the DAC setpoint. Append a
2507 * WORD value (that writes a channel 0 NOP command to a non-existent
2508 * main DAC channel) that serves to keep the clock running after the
2509 * packet has been sent to the target DAC.
2512 /* Address the DAC channel within the trimdac device. */
2513 SendDAC(dev, ((uint32_t) chan << 8)
2514 | (uint32_t) DacData); /* Include DAC setpoint data. */
2517 /* ************** EEPROM ACCESS FUNCTIONS ************** */
2518 /* Read uint8_t from EEPROM. */
2520 static uint8_t I2Cread(struct comedi_device *dev, uint8_t addr)
2524 /* Send EEPROM target address. */
2525 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CW)
2526 /* Byte2 = I2C command: write to I2C EEPROM device. */
2527 | I2C_B1(I2C_ATTRSTOP, addr)
2528 /* Byte1 = EEPROM internal target address. */
2529 | I2C_B0(I2C_ATTRNOP, 0))) { /* Byte0 = Not sent. */
2530 /* Abort function and declare error if handshake failed. */
2531 DEBUG("I2Cread: error handshake I2Cread a\n");
2534 /* Execute EEPROM read. */
2535 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CR)
2539 /* from I2C EEPROM */
2541 |I2C_B1(I2C_ATTRSTOP, 0)
2543 /* Byte1 receives */
2546 |I2C_B0(I2C_ATTRNOP, 0))) { /* Byte0 = Not sent. */
2548 /* Abort function and declare error if handshake failed. */
2549 DEBUG("I2Cread: error handshake I2Cread b\n");
2552 /* Return copy of EEPROM value. */
2553 rtnval = (uint8_t) (RR7146(P_I2CCTRL) >> 16);
2557 static uint32_t I2Chandshake(struct comedi_device *dev, uint32_t val)
2559 /* Write I2C command to I2C Transfer Control shadow register. */
2560 WR7146(P_I2CCTRL, val);
2562 /* Upload I2C shadow registers into working registers and wait for */
2563 /* upload confirmation. */
2565 MC_ENABLE(P_MC2, MC2_UPLD_IIC);
2566 while (!MC_TEST(P_MC2, MC2_UPLD_IIC))
2569 /* Wait until I2C bus transfer is finished or an error occurs. */
2570 while ((RR7146(P_I2CCTRL) & (I2C_BUSY | I2C_ERR)) == I2C_BUSY)
2573 /* Return non-zero if I2C error occurred. */
2574 return RR7146(P_I2CCTRL) & I2C_ERR;
2578 /* Private helper function: Write setpoint to an application DAC channel. */
2580 static void SetDAC(struct comedi_device *dev, uint16_t chan, short dacdata)
2582 register uint16_t signmask;
2583 register uint32_t WSImage;
2585 /* Adjust DAC data polarity and set up Polarity Control Register */
2587 signmask = 1 << chan;
2590 devpriv->Dacpol |= signmask;
2592 devpriv->Dacpol &= ~signmask;
2594 /* Limit DAC setpoint value to valid range. */
2595 if ((uint16_t) dacdata > 0x1FFF)
2598 /* Set up TSL2 records (aka "vectors") for DAC update. Vectors V2
2599 * and V3 transmit the setpoint to the target DAC. V4 and V5 send
2600 * data to a non-existent TrimDac channel just to keep the clock
2601 * running after sending data to the target DAC. This is necessary
2602 * to eliminate the clock glitch that would otherwise occur at the
2603 * end of the target DAC's serial data stream. When the sequence
2604 * restarts at V0 (after executing V5), the gate array automatically
2605 * disables gating for the DAC clock and all DAC chip selects.
2608 WSImage = (chan & 2) ? WS1 : WS2;
2609 /* Choose DAC chip select to be asserted. */
2610 SETVECT(2, XSD2 | XFIFO_1 | WSImage);
2611 /* Slot 2: Transmit high data byte to target DAC. */
2612 SETVECT(3, XSD2 | XFIFO_0 | WSImage);
2613 /* Slot 3: Transmit low data byte to target DAC. */
2614 SETVECT(4, XSD2 | XFIFO_3 | WS3);
2615 /* Slot 4: Transmit to non-existent TrimDac channel to keep clock */
2616 SETVECT(5, XSD2 | XFIFO_2 | WS3 | EOS);
2617 /* Slot 5: running after writing target DAC's low data byte. */
2619 /* Construct and transmit target DAC's serial packet:
2620 * ( A10D DDDD ),( DDDD DDDD ),( 0x0F ),( 0x00 ) where A is chan<0>,
2621 * and D<12:0> is the DAC setpoint. Append a WORD value (that writes
2622 * to a non-existent TrimDac channel) that serves to keep the clock
2623 * running after the packet has been sent to the target DAC.
2625 SendDAC(dev, 0x0F000000
2626 /* Continue clock after target DAC data (write to non-existent trimdac). */
2628 /* Address the two main dual-DAC devices (TSL's chip select enables
2629 * target device). */
2630 | ((uint32_t) (chan & 1) << 15)
2631 /* Address the DAC channel within the device. */
2632 | (uint32_t) dacdata); /* Include DAC setpoint data. */
2636 /* Private helper function: Transmit serial data to DAC via Audio
2637 * channel 2. Assumes: (1) TSL2 slot records initialized, and (2)
2638 * Dacpol contains valid target image.
2641 static void SendDAC(struct comedi_device *dev, uint32_t val)
2644 /* START THE SERIAL CLOCK RUNNING ------------- */
2646 /* Assert DAC polarity control and enable gating of DAC serial clock
2647 * and audio bit stream signals. At this point in time we must be
2648 * assured of being in time slot 0. If we are not in slot 0, the
2649 * serial clock and audio stream signals will be disabled; this is
2650 * because the following DEBIwrite statement (which enables signals
2651 * to be passed through the gate array) would execute before the
2652 * trailing edge of WS1/WS3 (which turns off the signals), thus
2653 * causing the signals to be inactive during the DAC write.
2655 DEBIwrite(dev, LP_DACPOL, devpriv->Dacpol);
2657 /* TRANSFER OUTPUT DWORD VALUE INTO A2'S OUTPUT FIFO ---------------- */
2659 /* Copy DAC setpoint value to DAC's output DMA buffer. */
2661 /* WR7146( (uint32_t)devpriv->pDacWBuf, val ); */
2662 *devpriv->pDacWBuf = val;
2664 /* enab the output DMA transfer. This will cause the DMAC to copy
2665 * the DAC's data value to A2's output FIFO. The DMA transfer will
2666 * then immediately terminate because the protection address is
2667 * reached upon transfer of the first DWORD value.
2669 MC_ENABLE(P_MC1, MC1_A2OUT);
2671 /* While the DMA transfer is executing ... */
2673 /* Reset Audio2 output FIFO's underflow flag (along with any other
2674 * FIFO underflow/overflow flags). When set, this flag will
2675 * indicate that we have emerged from slot 0.
2677 WR7146(P_ISR, ISR_AFOU);
2679 /* Wait for the DMA transfer to finish so that there will be data
2680 * available in the FIFO when time slot 1 tries to transfer a DWORD
2681 * from the FIFO to the output buffer register. We test for DMA
2682 * Done by polling the DMAC enable flag; this flag is automatically
2683 * cleared when the transfer has finished.
2685 while ((RR7146(P_MC1) & MC1_A2OUT) != 0)
2688 /* START THE OUTPUT STREAM TO THE TARGET DAC -------------------- */
2690 /* FIFO data is now available, so we enable execution of time slots
2691 * 1 and higher by clearing the EOS flag in slot 0. Note that SD3
2692 * will be shifted in and stored in FB_BUFFER2 for end-of-slot-list
2695 SETVECT(0, XSD2 | RSD3 | SIB_A2);
2697 /* Wait for slot 1 to execute to ensure that the Packet will be
2698 * transmitted. This is detected by polling the Audio2 output FIFO
2699 * underflow flag, which will be set when slot 1 execution has
2700 * finished transferring the DAC's data DWORD from the output FIFO
2701 * to the output buffer register.
2703 while ((RR7146(P_SSR) & SSR_AF2_OUT) == 0)
2706 /* Set up to trap execution at slot 0 when the TSL sequencer cycles
2707 * back to slot 0 after executing the EOS in slot 5. Also,
2708 * simultaneously shift out and in the 0x00 that is ALWAYS the value
2709 * stored in the last byte to be shifted out of the FIFO's DWORD
2712 SETVECT(0, XSD2 | XFIFO_2 | RSD2 | SIB_A2 | EOS);
2714 /* WAIT FOR THE TRANSACTION TO FINISH ----------------------- */
2716 /* Wait for the TSL to finish executing all time slots before
2717 * exiting this function. We must do this so that the next DAC
2718 * write doesn't start, thereby enabling clock/chip select signals:
2720 * 1. Before the TSL sequence cycles back to slot 0, which disables
2721 * the clock/cs signal gating and traps slot // list execution.
2722 * we have not yet finished slot 5 then the clock/cs signals are
2723 * still gated and we have not finished transmitting the stream.
2725 * 2. While slots 2-5 are executing due to a late slot 0 trap. In
2726 * this case, the slot sequence is currently repeating, but with
2727 * clock/cs signals disabled. We must wait for slot 0 to trap
2728 * execution before setting up the next DAC setpoint DMA transfer
2729 * and enabling the clock/cs signals. To detect the end of slot 5,
2730 * we test for the FB_BUFFER2 MSB contents to be equal to 0xFF. If
2731 * the TSL has not yet finished executing slot 5 ...
2733 if ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0) {
2734 /* The trap was set on time and we are still executing somewhere
2735 * in slots 2-5, so we now wait for slot 0 to execute and trap
2736 * TSL execution. This is detected when FB_BUFFER2 MSB changes
2737 * from 0xFF to 0x00, which slot 0 causes to happen by shifting
2738 * out/in on SD2 the 0x00 that is always referenced by slot 5.
2740 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0)
2743 /* Either (1) we were too late setting the slot 0 trap; the TSL
2744 * sequencer restarted slot 0 before we could set the EOS trap flag,
2745 * or (2) we were not late and execution is now trapped at slot 0.
2746 * In either case, we must now change slot 0 so that it will store
2747 * value 0xFF (instead of 0x00) to FB_BUFFER2 next time it executes.
2748 * In order to do this, we reprogram slot 0 so that it will shift in
2749 * SD3, which is driven only by a pull-up resistor.
2751 SETVECT(0, RSD3 | SIB_A2 | EOS);
2753 /* Wait for slot 0 to execute, at which time the TSL is setup for
2754 * the next DAC write. This is detected when FB_BUFFER2 MSB changes
2755 * from 0x00 to 0xFF.
2757 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) == 0)
2761 static void WriteMISC2(struct comedi_device *dev, uint16_t NewImage)
2763 DEBIwrite(dev, LP_MISC1, MISC1_WENABLE); /* enab writes to */
2764 /* MISC2 register. */
2765 DEBIwrite(dev, LP_WRMISC2, NewImage); /* Write new image to MISC2. */
2766 DEBIwrite(dev, LP_MISC1, MISC1_WDISABLE); /* Disable writes to MISC2. */
2769 /* Initialize the DEBI interface for all transfers. */
2771 static uint16_t DEBIread(struct comedi_device *dev, uint16_t addr)
2775 /* Set up DEBI control register value in shadow RAM. */
2776 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr);
2778 /* Execute the DEBI transfer. */
2781 /* Fetch target register value. */
2782 retval = (uint16_t) RR7146(P_DEBIAD);
2784 /* Return register value. */
2788 /* Execute a DEBI transfer. This must be called from within a */
2789 /* critical section. */
2790 static void DEBItransfer(struct comedi_device *dev)
2792 /* Initiate upload of shadow RAM to DEBI control register. */
2793 MC_ENABLE(P_MC2, MC2_UPLD_DEBI);
2795 /* Wait for completion of upload from shadow RAM to DEBI control */
2797 while (!MC_TEST(P_MC2, MC2_UPLD_DEBI))
2800 /* Wait until DEBI transfer is done. */
2801 while (RR7146(P_PSR) & PSR_DEBI_S)
2805 /* Write a value to a gate array register. */
2806 static void DEBIwrite(struct comedi_device *dev, uint16_t addr, uint16_t wdata)
2809 /* Set up DEBI control register value in shadow RAM. */
2810 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr);
2811 WR7146(P_DEBIAD, wdata);
2813 /* Execute the DEBI transfer. */
2817 /* Replace the specified bits in a gate array register. Imports: mask
2818 * specifies bits that are to be preserved, wdata is new value to be
2819 * or'd with the masked original.
2821 static void DEBIreplace(struct comedi_device *dev, uint16_t addr, uint16_t mask,
2825 /* Copy target gate array register into P_DEBIAD register. */
2826 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr);
2827 /* Set up DEBI control reg value in shadow RAM. */
2828 DEBItransfer(dev); /* Execute the DEBI Read transfer. */
2830 /* Write back the modified image. */
2831 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr);
2832 /* Set up DEBI control reg value in shadow RAM. */
2834 WR7146(P_DEBIAD, wdata | ((uint16_t) RR7146(P_DEBIAD) & mask));
2835 /* Modify the register image. */
2836 DEBItransfer(dev); /* Execute the DEBI Write transfer. */
2839 static void CloseDMAB(struct comedi_device *dev, struct bufferDMA *pdma,
2845 DEBUG("CloseDMAB: Entering S626DRV_CloseDMAB():\n");
2848 /* find the matching allocation from the board struct */
2850 vbptr = pdma->LogicalBase;
2851 vpptr = pdma->PhysicalBase;
2853 pci_free_consistent(devpriv->pdev, bsize, vbptr, vpptr);
2854 pdma->LogicalBase = 0;
2855 pdma->PhysicalBase = 0;
2857 DEBUG("CloseDMAB(): Logical=%p, bsize=%d, Physical=0x%x\n",
2858 vbptr, bsize, (uint32_t) vpptr);
2862 /* ****** COUNTER FUNCTIONS ******* */
2863 /* All counter functions address a specific counter by means of the
2864 * "Counter" argument, which is a logical counter number. The Counter
2865 * argument may have any of the following legal values: 0=0A, 1=1A,
2866 * 2=2A, 3=0B, 4=1B, 5=2B.
2869 /* Forward declarations for functions that are common to both A and B counters: */
2871 /* ****** PRIVATE COUNTER FUNCTIONS ****** */
2873 /* Read a counter's output latch. */
2875 static uint32_t ReadLatch(struct comedi_device *dev, struct enc_private *k)
2877 register uint32_t value;
2878 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch enter\n"); */
2880 /* Latch counts and fetch LSW of latched counts value. */
2881 value = (uint32_t) DEBIread(dev, k->MyLatchLsw);
2883 /* Fetch MSW of latched counts and combine with LSW. */
2884 value |= ((uint32_t) DEBIread(dev, k->MyLatchLsw + 2) << 16);
2886 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch exit\n"); */
2888 /* Return latched counts. */
2892 /* Reset a counter's index and overflow event capture flags. */
2894 static void ResetCapFlags_A(struct comedi_device *dev, struct enc_private *k)
2896 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL),
2897 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A);
2900 static void ResetCapFlags_B(struct comedi_device *dev, struct enc_private *k)
2902 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL),
2903 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B);
2906 /* Return counter setup in a format (COUNTER_SETUP) that is consistent */
2907 /* for both A and B counters. */
2909 static uint16_t GetMode_A(struct comedi_device *dev, struct enc_private *k)
2911 register uint16_t cra;
2912 register uint16_t crb;
2913 register uint16_t setup;
2915 /* Fetch CRA and CRB register images. */
2916 cra = DEBIread(dev, k->MyCRA);
2917 crb = DEBIread(dev, k->MyCRB);
2919 /* Populate the standardized counter setup bit fields. Note: */
2920 /* IndexSrc is restricted to ENC_X or IndxPol. */
2921 setup = ((cra & STDMSK_LOADSRC) /* LoadSrc = LoadSrcA. */
2922 |((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcA. */
2923 |((cra << (STDBIT_INTSRC - CRABIT_INTSRC_A)) & STDMSK_INTSRC) /* IntSrc = IntSrcA. */
2924 |((cra << (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1))) & STDMSK_INDXSRC) /* IndxSrc = IndxSrcA<1>. */
2925 |((cra >> (CRABIT_INDXPOL_A - STDBIT_INDXPOL)) & STDMSK_INDXPOL) /* IndxPol = IndxPolA. */
2926 |((crb >> (CRBBIT_CLKENAB_A - STDBIT_CLKENAB)) & STDMSK_CLKENAB)); /* ClkEnab = ClkEnabA. */
2928 /* Adjust mode-dependent parameters. */
2929 if (cra & (2 << CRABIT_CLKSRC_A)) /* If Timer mode (ClkSrcA<1> == 1): */
2930 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */
2931 |((cra << (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) & STDMSK_CLKPOL) /* Set ClkPol to indicate count direction (ClkSrcA<0>). */
2932 |(MULT_X1 << STDBIT_CLKMULT)); /* ClkMult must be 1x in Timer mode. */
2934 else /* If Counter mode (ClkSrcA<1> == 0): */
2935 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Counter mode. */
2936 |((cra >> (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) & STDMSK_CLKPOL) /* Pass through ClkPol. */
2937 |(((cra & CRAMSK_CLKMULT_A) == (MULT_X0 << CRABIT_CLKMULT_A)) ? /* Force ClkMult to 1x if not legal, else pass through. */
2938 (MULT_X1 << STDBIT_CLKMULT) :
2939 ((cra >> (CRABIT_CLKMULT_A -
2940 STDBIT_CLKMULT)) & STDMSK_CLKMULT)));
2942 /* Return adjusted counter setup. */
2946 static uint16_t GetMode_B(struct comedi_device *dev, struct enc_private *k)
2948 register uint16_t cra;
2949 register uint16_t crb;
2950 register uint16_t setup;
2952 /* Fetch CRA and CRB register images. */
2953 cra = DEBIread(dev, k->MyCRA);
2954 crb = DEBIread(dev, k->MyCRB);
2956 /* Populate the standardized counter setup bit fields. Note: */
2957 /* IndexSrc is restricted to ENC_X or IndxPol. */
2958 setup = (((crb << (STDBIT_INTSRC - CRBBIT_INTSRC_B)) & STDMSK_INTSRC) /* IntSrc = IntSrcB. */
2959 |((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcB. */
2960 |((crb << (STDBIT_LOADSRC - CRBBIT_LOADSRC_B)) & STDMSK_LOADSRC) /* LoadSrc = LoadSrcB. */
2961 |((crb << (STDBIT_INDXPOL - CRBBIT_INDXPOL_B)) & STDMSK_INDXPOL) /* IndxPol = IndxPolB. */
2962 |((crb >> (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) & STDMSK_CLKENAB) /* ClkEnab = ClkEnabB. */
2963 |((cra >> ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)) & STDMSK_INDXSRC)); /* IndxSrc = IndxSrcB<1>. */
2965 /* Adjust mode-dependent parameters. */
2966 if ((crb & CRBMSK_CLKMULT_B) == (MULT_X0 << CRBBIT_CLKMULT_B)) /* If Extender mode (ClkMultB == MULT_X0): */
2967 setup |= ((CLKSRC_EXTENDER << STDBIT_CLKSRC) /* Indicate Extender mode. */
2968 |(MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */
2969 |((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */
2971 else if (cra & (2 << CRABIT_CLKSRC_B)) /* If Timer mode (ClkSrcB<1> == 1): */
2972 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */
2973 |(MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */
2974 |((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */
2976 else /* If Counter mode (ClkSrcB<1> == 0): */
2977 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Timer mode. */
2978 |((crb >> (CRBBIT_CLKMULT_B - STDBIT_CLKMULT)) & STDMSK_CLKMULT) /* Clock multiplier is passed through. */
2979 |((crb << (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) & STDMSK_CLKPOL)); /* Clock polarity is passed through. */
2981 /* Return adjusted counter setup. */
2986 * Set the operating mode for the specified counter. The setup
2987 * parameter is treated as a COUNTER_SETUP data type. The following
2988 * parameters are programmable (all other parms are ignored): ClkMult,
2989 * ClkPol, ClkEnab, IndexSrc, IndexPol, LoadSrc.
2992 static void SetMode_A(struct comedi_device *dev, struct enc_private *k,
2993 uint16_t Setup, uint16_t DisableIntSrc)
2995 register uint16_t cra;
2996 register uint16_t crb;
2997 register uint16_t setup = Setup; /* Cache the Standard Setup. */
2999 /* Initialize CRA and CRB images. */
3000 cra = ((setup & CRAMSK_LOADSRC_A) /* Preload trigger is passed through. */
3001 |((setup & STDMSK_INDXSRC) >> (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1)))); /* IndexSrc is restricted to ENC_X or IndxPol. */
3003 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A /* Reset any pending CounterA event captures. */
3004 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_A - STDBIT_CLKENAB))); /* Clock enable is passed through. */
3006 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */
3008 cra |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC -
3011 /* Populate all mode-dependent attributes of CRA & CRB images. */
3012 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) {
3013 case CLKSRC_EXTENDER: /* Extender Mode: Force to Timer mode */
3014 /* (Extender valid only for B counters). */
3016 case CLKSRC_TIMER: /* Timer Mode: */
3017 cra |= ((2 << CRABIT_CLKSRC_A) /* ClkSrcA<1> selects system clock */
3018 |((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) /* with count direction (ClkSrcA<0>) obtained from ClkPol. */
3019 |(1 << CRABIT_CLKPOL_A) /* ClkPolA behaves as always-on clock enable. */
3020 |(MULT_X1 << CRABIT_CLKMULT_A)); /* ClkMult must be 1x. */
3023 default: /* Counter Mode: */
3024 cra |= (CLKSRC_COUNTER /* Select ENC_C and ENC_D as clock/direction inputs. */
3025 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) /* Clock polarity is passed through. */
3026 |(((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force multiplier to x1 if not legal, otherwise pass through. */
3027 (MULT_X1 << CRABIT_CLKMULT_A) :
3028 ((setup & STDMSK_CLKMULT) << (CRABIT_CLKMULT_A -
3032 /* Force positive index polarity if IndxSrc is software-driven only, */
3033 /* otherwise pass it through. */
3034 if (~setup & STDMSK_INDXSRC)
3035 cra |= ((setup & STDMSK_INDXPOL) << (CRABIT_INDXPOL_A -
3038 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */
3039 /* enable mask to indicate the counter interrupt is disabled. */
3041 devpriv->CounterIntEnabs &= ~k->MyEventBits[3];
3043 /* While retaining CounterB and LatchSrc configurations, program the */
3044 /* new counter operating mode. */
3045 DEBIreplace(dev, k->MyCRA, CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B, cra);
3046 DEBIreplace(dev, k->MyCRB,
3047 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)), crb);
3050 static void SetMode_B(struct comedi_device *dev, struct enc_private *k,
3051 uint16_t Setup, uint16_t DisableIntSrc)
3053 register uint16_t cra;
3054 register uint16_t crb;
3055 register uint16_t setup = Setup; /* Cache the Standard Setup. */
3057 /* Initialize CRA and CRB images. */
3058 cra = ((setup & STDMSK_INDXSRC) << ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)); /* IndexSrc field is restricted to ENC_X or IndxPol. */
3060 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B /* Reset event captures and disable interrupts. */
3061 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) /* Clock enable is passed through. */
3062 |((setup & STDMSK_LOADSRC) >> (STDBIT_LOADSRC - CRBBIT_LOADSRC_B))); /* Preload trigger source is passed through. */
3064 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */
3066 crb |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC -
3069 /* Populate all mode-dependent attributes of CRA & CRB images. */
3070 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) {
3071 case CLKSRC_TIMER: /* Timer Mode: */
3072 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB<1> selects system clock */
3073 |((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction (ClkSrcB<0>) obtained from ClkPol. */
3074 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB behaves as always-on clock enable. */
3075 |(MULT_X1 << CRBBIT_CLKMULT_B)); /* ClkMultB must be 1x. */
3078 case CLKSRC_EXTENDER: /* Extender Mode: */
3079 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB source is OverflowA (same as "timer") */
3080 |((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction obtained from ClkPol. */
3081 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB controls IndexB -- always set to active. */
3082 |(MULT_X0 << CRBBIT_CLKMULT_B)); /* ClkMultB selects OverflowA as the clock source. */
3085 default: /* Counter Mode: */
3086 cra |= (CLKSRC_COUNTER << CRABIT_CLKSRC_B); /* Select ENC_C and ENC_D as clock/direction inputs. */
3087 crb |= (((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) /* ClkPol is passed through. */
3088 |(((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force ClkMult to x1 if not legal, otherwise pass through. */
3089 (MULT_X1 << CRBBIT_CLKMULT_B) :
3090 ((setup & STDMSK_CLKMULT) << (CRBBIT_CLKMULT_B -
3094 /* Force positive index polarity if IndxSrc is software-driven only, */
3095 /* otherwise pass it through. */
3096 if (~setup & STDMSK_INDXSRC)
3097 crb |= ((setup & STDMSK_INDXPOL) >> (STDBIT_INDXPOL -
3100 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */
3101 /* enable mask to indicate the counter interrupt is disabled. */
3103 devpriv->CounterIntEnabs &= ~k->MyEventBits[3];
3105 /* While retaining CounterA and LatchSrc configurations, program the */
3106 /* new counter operating mode. */
3107 DEBIreplace(dev, k->MyCRA,
3108 (uint16_t) (~(CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B)), cra);
3109 DEBIreplace(dev, k->MyCRB, CRBMSK_CLKENAB_A | CRBMSK_LATCHSRC, crb);
3112 /* Return/set a counter's enable. enab: 0=always enabled, 1=enabled by index. */
3114 static void SetEnable_A(struct comedi_device *dev, struct enc_private *k,
3117 DEBUG("SetEnable_A: SetEnable_A enter 3541\n");
3118 DEBIreplace(dev, k->MyCRB,
3119 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)),
3120 (uint16_t) (enab << CRBBIT_CLKENAB_A));
3123 static void SetEnable_B(struct comedi_device *dev, struct enc_private *k,
3126 DEBIreplace(dev, k->MyCRB,
3127 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_B)),
3128 (uint16_t) (enab << CRBBIT_CLKENAB_B));
3131 static uint16_t GetEnable_A(struct comedi_device *dev, struct enc_private *k)
3133 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_A) & 1;
3136 static uint16_t GetEnable_B(struct comedi_device *dev, struct enc_private *k)
3138 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_B) & 1;
3141 /* Return/set a counter pair's latch trigger source. 0: On read
3142 * access, 1: A index latches A, 2: B index latches B, 3: A overflow
3146 static void SetLatchSource(struct comedi_device *dev, struct enc_private *k,
3149 DEBUG("SetLatchSource: SetLatchSource enter 3550\n");
3150 DEBIreplace(dev, k->MyCRB,
3151 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_LATCHSRC)),
3152 (uint16_t) (value << CRBBIT_LATCHSRC));
3154 DEBUG("SetLatchSource: SetLatchSource exit\n");
3158 * static uint16_t GetLatchSource(struct comedi_device *dev, struct enc_private *k )
3160 * return ( DEBIread( dev, k->MyCRB) >> CRBBIT_LATCHSRC ) & 3;
3165 * Return/set the event that will trigger transfer of the preload
3166 * register into the counter. 0=ThisCntr_Index, 1=ThisCntr_Overflow,
3167 * 2=OverflowA (B counters only), 3=disabled.
3170 static void SetLoadTrig_A(struct comedi_device *dev, struct enc_private *k,
3173 DEBIreplace(dev, k->MyCRA, (uint16_t) (~CRAMSK_LOADSRC_A),
3174 (uint16_t) (Trig << CRABIT_LOADSRC_A));
3177 static void SetLoadTrig_B(struct comedi_device *dev, struct enc_private *k,
3180 DEBIreplace(dev, k->MyCRB,
3181 (uint16_t) (~(CRBMSK_LOADSRC_B | CRBMSK_INTCTRL)),
3182 (uint16_t) (Trig << CRBBIT_LOADSRC_B));
3185 static uint16_t GetLoadTrig_A(struct comedi_device *dev, struct enc_private *k)
3187 return (DEBIread(dev, k->MyCRA) >> CRABIT_LOADSRC_A) & 3;
3190 static uint16_t GetLoadTrig_B(struct comedi_device *dev, struct enc_private *k)
3192 return (DEBIread(dev, k->MyCRB) >> CRBBIT_LOADSRC_B) & 3;
3195 /* Return/set counter interrupt source and clear any captured
3196 * index/overflow events. IntSource: 0=Disabled, 1=OverflowOnly,
3197 * 2=IndexOnly, 3=IndexAndOverflow.
3200 static void SetIntSrc_A(struct comedi_device *dev, struct enc_private *k,
3203 /* Reset any pending counter overflow or index captures. */
3204 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL),
3205 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A);
3207 /* Program counter interrupt source. */
3208 DEBIreplace(dev, k->MyCRA, ~CRAMSK_INTSRC_A,
3209 (uint16_t) (IntSource << CRABIT_INTSRC_A));
3211 /* Update MISC2 interrupt enable mask. */
3212 devpriv->CounterIntEnabs =
3213 (devpriv->CounterIntEnabs & ~k->
3214 MyEventBits[3]) | k->MyEventBits[IntSource];
3217 static void SetIntSrc_B(struct comedi_device *dev, struct enc_private *k,
3222 /* Cache writeable CRB register image. */
3223 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL;
3225 /* Reset any pending counter overflow or index captures. */
3226 DEBIwrite(dev, k->MyCRB,
3227 (uint16_t) (crb | CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B));
3229 /* Program counter interrupt source. */
3230 DEBIwrite(dev, k->MyCRB,
3231 (uint16_t) ((crb & ~CRBMSK_INTSRC_B) | (IntSource <<
3234 /* Update MISC2 interrupt enable mask. */
3235 devpriv->CounterIntEnabs =
3236 (devpriv->CounterIntEnabs & ~k->
3237 MyEventBits[3]) | k->MyEventBits[IntSource];
3240 static uint16_t GetIntSrc_A(struct comedi_device *dev, struct enc_private *k)
3242 return (DEBIread(dev, k->MyCRA) >> CRABIT_INTSRC_A) & 3;
3245 static uint16_t GetIntSrc_B(struct comedi_device *dev, struct enc_private *k)
3247 return (DEBIread(dev, k->MyCRB) >> CRBBIT_INTSRC_B) & 3;
3250 /* Return/set the clock multiplier. */
3252 /* static void SetClkMult(struct comedi_device *dev, struct enc_private *k, uint16_t value ) */
3254 /* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKMULT ) | ( value << STDBIT_CLKMULT ) ), FALSE ); */
3257 /* static uint16_t GetClkMult(struct comedi_device *dev, struct enc_private *k ) */
3259 /* return ( k->GetMode(dev, k ) >> STDBIT_CLKMULT ) & 3; */
3262 /* Return/set the clock polarity. */
3264 /* static void SetClkPol( struct comedi_device *dev,struct enc_private *k, uint16_t value ) */
3266 /* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKPOL ) | ( value << STDBIT_CLKPOL ) ), FALSE ); */
3269 /* static uint16_t GetClkPol(struct comedi_device *dev, struct enc_private *k ) */
3271 /* return ( k->GetMode(dev, k ) >> STDBIT_CLKPOL ) & 1; */
3274 /* Return/set the clock source. */
3276 /* static void SetClkSrc( struct comedi_device *dev,struct enc_private *k, uint16_t value ) */
3278 /* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKSRC ) | ( value << STDBIT_CLKSRC ) ), FALSE ); */
3281 /* static uint16_t GetClkSrc( struct comedi_device *dev,struct enc_private *k ) */
3283 /* return ( k->GetMode(dev, k ) >> STDBIT_CLKSRC ) & 3; */
3286 /* Return/set the index polarity. */
3288 /* static void SetIndexPol(struct comedi_device *dev, struct enc_private *k, uint16_t value ) */
3290 /* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXPOL ) | ( (value != 0) << STDBIT_INDXPOL ) ), FALSE ); */
3293 /* static uint16_t GetIndexPol(struct comedi_device *dev, struct enc_private *k ) */
3295 /* return ( k->GetMode(dev, k ) >> STDBIT_INDXPOL ) & 1; */
3298 /* Return/set the index source. */
3300 /* static void SetIndexSrc(struct comedi_device *dev, struct enc_private *k, uint16_t value ) */
3302 /* DEBUG("SetIndexSrc: set index src enter 3700\n"); */
3303 /* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXSRC ) | ( (value != 0) << STDBIT_INDXSRC ) ), FALSE ); */
3306 /* static uint16_t GetIndexSrc(struct comedi_device *dev, struct enc_private *k ) */
3308 /* return ( k->GetMode(dev, k ) >> STDBIT_INDXSRC ) & 1; */
3311 /* Generate an index pulse. */
3313 static void PulseIndex_A(struct comedi_device *dev, struct enc_private *k)
3315 register uint16_t cra;
3317 DEBUG("PulseIndex_A: pulse index enter\n");
3319 cra = DEBIread(dev, k->MyCRA); /* Pulse index. */
3320 DEBIwrite(dev, k->MyCRA, (uint16_t) (cra ^ CRAMSK_INDXPOL_A));
3321 DEBUG("PulseIndex_A: pulse index step1\n");
3322 DEBIwrite(dev, k->MyCRA, cra);
3325 static void PulseIndex_B(struct comedi_device *dev, struct enc_private *k)
3327 register uint16_t crb;
3329 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL; /* Pulse index. */
3330 DEBIwrite(dev, k->MyCRB, (uint16_t) (crb ^ CRBMSK_INDXPOL_B));
3331 DEBIwrite(dev, k->MyCRB, crb);
3334 /* Write value into counter preload register. */
3336 static void Preload(struct comedi_device *dev, struct enc_private *k,
3339 DEBUG("Preload: preload enter\n");
3340 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw), (uint16_t) value); /* Write value to preload register. */
3341 DEBUG("Preload: preload step 1\n");
3342 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw + 2),
3343 (uint16_t) (value >> 16));
3346 static void CountersInit(struct comedi_device *dev)
3349 struct enc_private *k;
3350 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */
3352 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */
3353 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is counter. */
3354 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */
3355 (CNTDIR_UP << BF_CLKPOL) | /* Count direction is up. */
3356 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */
3357 (CLKENAB_INDEX << BF_CLKENAB); /* Enabled by index */
3359 /* Disable all counter interrupts and clear any captured counter events. */
3360 for (chan = 0; chan < S626_ENCODER_CHANNELS; chan++) {
3362 k->SetMode(dev, k, Setup, TRUE);
3363 k->SetIntSrc(dev, k, 0);
3364 k->ResetCapFlags(dev, k);
3365 k->SetEnable(dev, k, CLKENAB_ALWAYS);
3367 DEBUG("CountersInit: counters initialized\n");