drivers/staging/wilc1000/wilc_wlan_if.h

   1 /* ///////////////////////////////////////////////////////////////////////// */
   2 /*  */
   3 /* Copyright (c) Atmel Corporation.  All rights reserved. */
   4 /*  */
   5 /* Module Name:  wilc_wlan_if.h */
   6 /*  */
   7 /*  */
   8 /* ///////////////////////////////////////////////////////////////////////// */
   9
  10 #ifndef WILC_WLAN_IF_H
  11 #define WILC_WLAN_IF_H
  12
  13 #include <linux/semaphore.h>
  14 #include "linux_wlan_common.h"
  15 #include <linux/netdevice.h>
  16
  17 /********************************************
  18  *
  19  *      Debug Flags
  20  *
  21  ********************************************/
  22
  23 #define N_INIT                  0x00000001
  24 #define N_ERR                   0x00000002
  25 #define N_TXQ                   0x00000004
  26 #define N_INTR                  0x00000008
  27 #define N_RXQ                   0x00000010
  28
  29 /********************************************
  30  *
  31  *      Host Interface Defines
  32  *
  33  ********************************************/
  34
  35 #define HIF_SDIO                (0)
  36 #define HIF_SPI                 BIT(0)
  37 #define HIF_SDIO_GPIO_IRQ       BIT(2)
  38
  39 /********************************************
  40  *
  41  *      Tx/Rx Buffer Size Defines
  42  *
  43  ********************************************/
  44
  45 #define CE_TX_BUFFER_SIZE       (64 * 1024)
  46 #define CE_RX_BUFFER_SIZE       (384 * 1024)
  47
  48 /********************************************
  49  *
  50  *      Wlan Interface Defines
  51  *
  52  ********************************************/
  53
  54 typedef struct {
  55         u32 read_write:         1;
  56         u32 function:           3;
  57         u32 raw:                1;
  58         u32 address:            17;
  59         u32 data:               8;
  60 } sdio_cmd52_t;
  61
  62 typedef struct {
  63         /* struct { */
  64         u32 read_write:         1;
  65         u32 function:           3;
  66         u32 block_mode:         1;
  67         u32 increment:          1;
  68         u32 address:            17;
  69         u32 count:              9;
  70         /* } bit; */
  71         u8 *buffer;
  72         u32 block_size;
  73 } sdio_cmd53_t;
  74
  75 #define WILC_MAC_INDICATE_STATUS        0x1
  76 #define WILC_MAC_STATUS_INIT            -1
  77 #define WILC_MAC_STATUS_READY           0
  78 #define WILC_MAC_STATUS_CONNECT         1
  79
  80 #define WILC_MAC_INDICATE_SCAN          0x2
  81
  82 struct tx_complete_data {
  83         int size;
  84         void *buff;
  85         u8 *pBssid;
  86         struct sk_buff *skb;
  87 };
  88
  89 typedef void (*wilc_tx_complete_func_t)(void *, int);
  90
  91 #define WILC_TX_ERR_NO_BUF      (-2)
  92
  93 /********************************************
  94  *
  95  *      Wlan Configuration ID
  96  *
  97  ********************************************/
  98
  99 #define MAX_SSID_LEN            33
 100 #define MAX_RATES_SUPPORTED     12
 101
 102 #define INFINITE_SLEEP_TIME     ((u32)0xFFFFFFFF)
 103
 104 typedef enum {
 105         SUPP_RATES_IE           = 1,
 106         EXT_SUPP_RATES_IE       = 50,
 107         HT_CAPABILITY_IE        = 45,
 108         RSN_IE                  = 48,
 109         WPA_IE                  = 221,
 110         WMM_IE                  = 221,
 111         P2P_IE                  = 221,
 112 } BEACON_IE;
 113
 114 typedef enum {
 115         INFRASTRUCTURE          = 0,
 116         INDEPENDENT,
 117         AP,
 118 } BSSTYPE_T;
 119
 120 typedef enum {
 121         RATE_AUTO               = 0,
 122         RATE_1MB                = 1,
 123         RATE_2MB                = 2,
 124         RATE_5MB                = 5,
 125         RATE_6MB                = 6,
 126         RATE_9MB                = 9,
 127         RATE_11MB               = 11,
 128         RATE_12MB               = 12,
 129         RATE_18MB               = 18,
 130         RATE_24MB               = 24,
 131         RATE_26MB               = 36,
 132         RATE_48MB               = 48,
 133         RATE_54MB               = 54
 134 } TX_RATE_T;
 135
 136 typedef enum {
 137         B_ONLY_MODE             = 0,    /* 1, 2 M, otherwise 5, 11 M */
 138         G_ONLY_MODE,                    /* 6,12,24 otherwise 9,18,36,48,54 */
 139         G_MIXED_11B_1_MODE,             /* 1,2,5.5,11 otherwise all on */
 140         G_MIXED_11B_2_MODE,             /* 1,2,5,11,6,12,24 otherwise all on */
 141 } G_OPERATING_MODE_T;
 142
 143 typedef enum {
 144         G_SHORT_PREAMBLE        = 0,    /* Short Preamble */
 145         G_LONG_PREAMBLE         = 1,    /* Long Preamble */
 146         G_AUTO_PREAMBLE         = 2,    /* Auto Preamble Selection */
 147 } G_PREAMBLE_T;
 148
 149 #define MAC_CONNECTED           1
 150 #define MAC_DISCONNECTED        0
 151
 152 #define SCAN_DONE               TRUE
 153 typedef enum {
 154         PASSIVE_SCAN            = 0,
 155         ACTIVE_SCAN             = 1,
 156 } SCANTYPE_T;
 157
 158 typedef enum {
 159         NO_POWERSAVE            = 0,
 160         MIN_FAST_PS             = 1,
 161         MAX_FAST_PS             = 2,
 162         MIN_PSPOLL_PS           = 3,
 163         MAX_PSPOLL_PS           = 4
 164 } USER_PS_MODE_T;
 165
 166 typedef enum {
 167         CHIP_WAKEDUP            = 0,
 168         CHIP_SLEEPING_AUTO      = 1,
 169         CHIP_SLEEPING_MANUAL    = 2
 170 } CHIP_PS_STATE_T;
 171
 172 typedef enum {
 173         ACQUIRE_ONLY            = 0,
 174         ACQUIRE_AND_WAKEUP      = 1,
 175 } BUS_ACQUIRE_T;
 176
 177 typedef enum {
 178         RELEASE_ONLY            = 0,
 179         RELEASE_ALLOW_SLEEP     = 1,
 180 } BUS_RELEASE_T;
 181
 182 typedef enum {
 183         NO_SECURITY             = 0,
 184         WEP_40                  = 0x3,
 185         WEP_104                 = 0x7,
 186         WPA_AES                 = 0x29,
 187         WPA_TKIP                = 0x49,
 188         WPA_AES_TKIP            = 0x69, /* Aes or Tkip */
 189         WPA2_AES                = 0x31,
 190         WPA2_TKIP               = 0x51,
 191         WPA2_AES_TKIP           = 0x71, /* Aes or Tkip */
 192 } SECURITY_T;
 193
 194 enum AUTHTYPE {
 195         OPEN_SYSTEM             = 1,
 196         SHARED_KEY              = 2,
 197         ANY                     = 3,
 198         IEEE8021                = 5
 199 };
 200
 201 enum SITESURVEY {
 202         SITE_SURVEY_1CH         = 0,
 203         SITE_SURVEY_ALL_CH      = 1,
 204         SITE_SURVEY_OFF         = 2
 205 };
 206
 207 typedef enum {
 208         NORMAL_ACK              = 0,
 209         NO_ACK,
 210 } ACK_POLICY_T;
 211
 212 typedef enum {
 213         DONT_RESET              = 0,
 214         DO_RESET                = 1,
 215         NO_REQUEST              = 2,
 216 } RESET_REQ_T;
 217
 218 typedef enum {
 219         REKEY_DISABLE           = 1,
 220         REKEY_TIME_BASE,
 221         REKEY_PKT_BASE,
 222         REKEY_TIME_PKT_BASE
 223 } RSNA_REKEY_POLICY_T;
 224
 225 typedef enum {
 226         FILTER_NO               = 0x00,
 227         FILTER_AP_ONLY          = 0x01,
 228         FILTER_STA_ONLY         = 0x02
 229 } SCAN_CLASS_FITLER_T;
 230
 231 typedef enum {
 232         PRI_HIGH_RSSI           = 0x00,
 233         PRI_LOW_RSSI            = 0x04,
 234         PRI_DETECT              = 0x08
 235 } SCAN_PRI_T;
 236
 237 typedef enum {
 238         CH_FILTER_OFF           = 0x00,
 239         CH_FILTER_ON            = 0x10
 240 } CH_FILTER_T;
 241
 242 typedef enum {
 243         AUTO_PROT               = 0,    /* Auto */
 244         NO_PROT,                        /* Do not use any protection */
 245         ERP_PROT,                       /* Protect all ERP frame exchanges */
 246         HT_PROT,                        /* Protect all HT frame exchanges  */
 247         GF_PROT,                        /* Protect all GF frame exchanges  */
 248 } N_PROTECTION_MODE_T;
 249
 250 typedef enum {
 251         G_SELF_CTS_PROT,
 252         G_RTS_CTS_PROT,
 253 } G_PROTECTION_MODE_T;
 254
 255 typedef enum {
 256         HT_MIXED_MODE           = 1,
 257         HT_ONLY_20MHZ_MODE,
 258         HT_ONLY_20_40MHZ_MODE,
 259 } N_OPERATING_MODE_T;
 260
 261 typedef enum {
 262         NO_DETECT               = 0,
 263         DETECT_ONLY             = 1,
 264         DETECT_PROTECT          = 2,
 265         DETECT_PROTECT_REPORT   = 3,
 266 } N_OBSS_DETECTION_T;
 267
 268 typedef enum {
 269         RTS_CTS_NONHT_PROT      = 0,    /* RTS-CTS at non-HT rate */
 270         FIRST_FRAME_NONHT_PROT,         /* First frame at non-HT rate */
 271         LSIG_TXOP_PROT,                 /* LSIG TXOP Protection */
 272         FIRST_FRAME_MIXED_PROT,         /* First frame at Mixed format */
 273 } N_PROTECTION_TYPE_T;
 274
 275 typedef enum {
 276         STATIC_MODE             = 1,
 277         DYNAMIC_MODE            = 2,
 278         MIMO_MODE               = 3,    /* power save disable */
 279 } N_SMPS_MODE_T;
 280
 281 typedef enum {
 282         DISABLE_SELF_CTS,
 283         ENABLE_SELF_CTS,
 284         DISABLE_TX_ABORT,
 285         ENABLE_TX_ABORT,
 286         HW_TRIGGER_ABORT,
 287         SW_TRIGGER_ABORT,
 288 } TX_ABORT_OPTION_T;
 289
 290 enum wid_type {
 291         WID_CHAR                = 0,
 292         WID_SHORT               = 1,
 293         WID_INT                 = 2,
 294         WID_STR                 = 3,
 295         WID_BIN_DATA            = 4,
 296         WID_BIN                 = 5,
 297         WID_IP                  = 6,
 298         WID_ADR                 = 7,
 299         WID_UNDEF               = 8,
 300         WID_TYPE_FORCE_32BIT    = 0xFFFFFFFF
 301 };
 302
 303 typedef enum {
 304         WID_NIL                         = 0xffff,
 305
 306         /*
 307          *  BSS Type
 308          *  -----------------------------------------------------------
 309          *  Configuration : Infrastructure   Independent   Access Point
 310          *  Values to set :         0               1            2
 311          *  -----------------------------------------------------------
 312          */
 313         WID_BSS_TYPE                    = 0x0000,
 314
 315         /*
 316          *  Transmit Rate
 317          *  -----------------------------------------------------------
 318          *  Configuration : 1  2  5.5  11  6  9  12  18  24  36  48  54
 319          *  Values to set : 1  2    5  11  6  9  12  18  24  36  48  54
 320          *  -----------------------------------------------------------
 321          */
 322         WID_CURRENT_TX_RATE             = 0x0001,
 323
 324         /*
 325          *  Channel
 326          *  -----------------------------------------------------------
 327          *  Configuration(g) : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 328          *  Values to set    : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 329          *  -----------------------------------------------------------
 330          */
 331         WID_CURRENT_CHANNEL             = 0x0002,
 332
 333         /*
 334          *  Preamble
 335          *  -----------------------------------------------------------
 336          *  Configuration :    short    long      Auto
 337          *  Values to set :       0       1         2
 338          *  -----------------------------------------------------------
 339          */
 340         WID_PREAMBLE                    = 0x0003,
 341
 342         /*
 343          * 11g operating mode (ignored if 11g not present)
 344          *  -----------------------------------------------------------
 345          *  Configuration :   HighPerf  Compat(RSet #1) Compat(RSet #2)
 346          *  Values to set :          1               2               3
 347          *  -----------------------------------------------------------
 348          */
 349         WID_11G_OPERATING_MODE          = 0x0004,
 350
 351         /*
 352          *  Mac status (response only)
 353          *  -----------------------------------------------------------
 354          *  Configuration :   disconnect  connect
 355          *  Values to get :          0       1
 356          *  -----------------------------------------------------------
 357          */
 358         WID_STATUS                      = 0x0005,
 359
 360         /*
 361          *  Scan type
 362          *  -----------------------------------------------------------
 363          *  Configuration :   Passive Scanning   Active Scanning
 364          *  Values to set :                  0                 1
 365          *  -----------------------------------------------------------
 366          */
 367         WID_SCAN_TYPE                   = 0x0007,
 368
 369         /*
 370          *  Key Id (WEP default key Id)
 371          *  -----------------------------------------------------------
 372          *  Configuration :   Any value between 0 to 3
 373          *  Values to set :   Same value. Default is 0
 374          *  -----------------------------------------------------------
 375          */
 376         WID_KEY_ID                      = 0x0009,
 377
 378         /*
 379          *  QoS Enable
 380          *  -----------------------------------------------------------
 381          *  Configuration :   QoS Disable   WMM Enable
 382          *  Values to set :   0             1
 383          *  -----------------------------------------------------------
 384          */
 385         WID_QOS_ENABLE                  = 0x000A,
 386
 387         /*
 388          *  Power Management
 389          *  -----------------------------------------------------------
 390          *  Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
 391          *  Values to set : 0            1             2
 392          *  -----------------------------------------------------------
 393          */
 394         WID_POWER_MANAGEMENT            = 0x000B,
 395
 396         /*
 397          *  WEP/802 11I Configuration
 398          *  -----------------------------------------------------------
 399          *  Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
 400          *  Values (0x)  :   00     03   07     29       49       31      51
 401          *  Configuration:WPA-AES+TKIP RSN-AES+TKIP
 402          *  Values (0x)  :      69        71
 403          *  -----------------------------------------------------------
 404          */
 405         WID_11I_MODE                    = 0x000C,
 406
 407         /*
 408          *  WEP Configuration: Used in BSS STA mode only when WEP is enabled
 409          *  -----------------------------------------------------------
 410          *  Configuration : Open System Shared Key Any Type | 802.1x Auth
 411          *  Values (0x)   :    01             02         03 |    BIT2
 412          *  -----------------------------------------------------------
 413          */
 414         WID_AUTH_TYPE                   = 0x000D,
 415
 416         /*
 417          *  Site Survey Type
 418          *  -----------------------------------------------------------
 419          *  Configuration       :  Values to set
 420          *  Survey 1 Channel    :  0
 421          *  survey all Channels :  1
 422          *  Disable Site Survey :  2
 423          *  -----------------------------------------------------------
 424          */
 425         WID_SITE_SURVEY                 = 0x000E,
 426
 427         /*
 428          *  Listen Interval
 429          *  -----------------------------------------------------------
 430          *  Configuration :   Any value between 1 to 255
 431          *  Values to set :   Same value. Default is 3
 432          *  -----------------------------------------------------------
 433          */
 434         WID_LISTEN_INTERVAL             = 0x000F,
 435
 436         /*
 437          *  DTIM Period
 438          *  -----------------------------------------------------------
 439          *  Configuration :   Any value between 1 to 255
 440          *  Values to set :   Same value. Default is 3
 441          *  -----------------------------------------------------------
 442          */
 443         WID_DTIM_PERIOD                 = 0x0010,
 444
 445         /*
 446          *  ACK Policy
 447          *  -----------------------------------------------------------
 448          *  Configuration :   Normal Ack            No Ack
 449          *  Values to set :       0                   1
 450          *  -----------------------------------------------------------
 451          */
 452         WID_ACK_POLICY                  = 0x0011,
 453
 454         /*
 455          *  Reset MAC (Set only)
 456          *  -----------------------------------------------------------
 457          *  Configuration :   Don't Reset       Reset   No Request
 458          *  Values to set :       0               1         2
 459          *  -----------------------------------------------------------
 460          */
 461         WID_RESET                       = 0x0012,
 462
 463         /*
 464          *  Broadcast SSID Option: Setting this will adhere to "" SSID element
 465          *  -----------------------------------------------------------
 466          *  Configuration :   Enable             Disable
 467          *  Values to set :   1                  0
 468          *  -----------------------------------------------------------
 469          */
 470         WID_BCAST_SSID                  = 0x0015,
 471
 472         /*
 473          *  Disconnect (Station)
 474          *  -----------------------------------------------------------
 475          *  Configuration :   Association ID
 476          *  Values to set :   Association ID
 477          *  -----------------------------------------------------------
 478          */
 479         WID_DISCONNECT                  = 0x0016,
 480
 481         /*
 482          *  11a Tx Power Level
 483          *  -----------------------------------------------------------
 484          *  Configuration : Sets TX Power (Higher the value greater the power)
 485          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 486          *  -----------------------------------------------------------
 487          */
 488         WID_TX_POWER_LEVEL_11A          = 0x0018,
 489
 490         /*
 491          *  Group Key Update Policy Selection
 492          *  -----------------------------------------------------------
 493          *  Configuration : Disabled timeBased packetBased timePacketBased
 494          *  Values to set :   1            2          3              4
 495          *  -----------------------------------------------------------
 496          */
 497         WID_REKEY_POLICY                = 0x0019,
 498
 499         /*
 500          *  Allow Short Slot
 501          *  -----------------------------------------------------------
 502          *  Configuration : Disallow Short Slot      Allow Short Slot
 503          *          (Enable Only Long Slot) (Enable Short Slot if applicable)
 504          *  Values to set :    0         1
 505          *  -----------------------------------------------------------
 506          */
 507         WID_SHORT_SLOT_ALLOWED          = 0x001A,
 508
 509         WID_PHY_ACTIVE_REG              = 0x001B,
 510
 511         /*
 512          *  11b Tx Power Level
 513          *  -----------------------------------------------------------
 514          *  Configuration : Sets TX Power (Higher the value greater the power)
 515          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 516          *  -----------------------------------------------------------
 517          */
 518         WID_TX_POWER_LEVEL_11B          = 0x001D,
 519
 520         /*
 521          *  Scan Request
 522          *  -----------------------------------------------------------
 523          *  Configuration : Request default scan
 524          *  Values to set : 0
 525          *  -----------------------------------------------------------
 526          */
 527         WID_START_SCAN_REQ              = 0x001E,
 528
 529         /*
 530          *  Rssi (get only)
 531          *  -----------------------------------------------------------
 532          *  Configuration :
 533          *  Values to get : Rssi value
 534          *  -----------------------------------------------------------
 535          */
 536         WID_RSSI                        = 0x001F,
 537
 538         /*
 539          * Join Request
 540          *  -----------------------------------------------------------
 541          *  Configuration : Request to join
 542          *  Values to set : index of scan result
 543          *  -----------------------------------------------------------
 544          */
 545         WID_JOIN_REQ                    = 0x0020,
 546
 547         WID_LINKSPEED                   = 0x0026,
 548
 549         /*
 550          *  Enable User Control of TX Power
 551          *  -----------------------------------------------------------
 552          *  Configuration : Disable                  Enable
 553          *  Values to set :    0                       1
 554          *  -----------------------------------------------------------
 555          */
 556         WID_USER_CONTROL_ON_TX_POWER    = 0x0027,
 557
 558         WID_MEMORY_ACCESS_8BIT          = 0x0029,
 559
 560         /*
 561          *  Enable Auto RX Sensitivity feature
 562          *  -----------------------------------------------------------
 563          *  Configuration : Disable                  Enable
 564          *  Values to set :    0                       1
 565          *  -----------------------------------------------------------
 566          */
 567         WID_AUTO_RX_SENSITIVITY         = 0x0032,
 568
 569         /*
 570          *  Receive Buffer Based Ack
 571          *  -----------------------------------------------------------
 572          *  Configuration : Disable                  Enable
 573          *  Values to set :    0                       1
 574          *  -----------------------------------------------------------
 575          */
 576         WID_DATAFLOW_CONTROL            = 0x0033,
 577
 578         /*
 579          *  Scan Filter
 580          *  -----------------------------------------------------------
 581          *  Configuration : Class       No filter   AP only   Station Only
 582          *  Values to set :                0           1           2
 583          *  Configuration : Priority    High Rssi   Low Rssi     Detect
 584          *  Values to set :                0          0x4         0x0
 585          *  Configuration : Channel     filter off  filter on
 586          *  Values to set :                0          0x10
 587          *  -----------------------------------------------------------
 588          */
 589         WID_SCAN_FILTER                 = 0x0036,
 590
 591         /*
 592          *  Link Loss Threshold (measure in the beacon period)
 593          *  -----------------------------------------------------------
 594          *  Configuration : Any value between 10 and 254(Set to 255 disable)
 595          *  Values to set : Same value. Default is 10
 596          *  -----------------------------------------------------------
 597          */
 598         WID_LINK_LOSS_THRESHOLD         = 0x0037,
 599
 600         WID_ABORT_RUNNING_SCAN          = 0x003E,
 601
 602         /* NMAC Character WID list */
 603         WID_WPS_START                   = 0x0043,
 604
 605         /*
 606          *  Protection mode for MAC
 607          *  -----------------------------------------------------------
 608          *  Configuration :  Auto  No protection  ERP    HT    GF
 609          *  Values to set :  0     1              2      3     4
 610          *  -----------------------------------------------------------
 611          */
 612         WID_11N_PROT_MECH               = 0x0080,
 613
 614         /*
 615          *  ERP Protection type for MAC
 616          *  -----------------------------------------------------------
 617          *  Configuration :  Self-CTS   RTS-CTS
 618          *  Values to set :  0          1
 619          *  -----------------------------------------------------------
 620          */
 621         WID_11N_ERP_PROT_TYPE           = 0x0081,
 622
 623         /*
 624          *  HT Option Enable
 625          *  -----------------------------------------------------------
 626          *  Configuration :   HT Enable          HT Disable
 627          *  Values to set :   1                  0
 628          *  -----------------------------------------------------------
 629          */
 630         WID_11N_ENABLE                  = 0x0082,
 631
 632         /*
 633          *  11n Operating mode (Note that 11g operating mode will also be
 634          *  used in addition to this, if this is set to HT Mixed mode)
 635          *  -----------------------------------------------------------
 636          *   Configuration :  HT Mixed  HT Only-20MHz   HT Only-20/40MHz
 637          *  Values to set :     1         2               3
 638          *  -----------------------------------------------------------
 639          */
 640         WID_11N_OPERATING_MODE          = 0x0083,
 641
 642         /*
 643          *  11n OBSS non-HT STA Detection flag
 644          *  -----------------------------------------------------------
 645          *  Configuration :  Do not detect
 646          *  Values to set :  0
 647          *  Configuration :  Detect, do not protect or report
 648          *  Values to set :  1
 649          *  Configuration :  Detect, protect and do not report
 650          *  Values to set :  2
 651          *  Configuration :  Detect, protect and report to other BSS
 652          *  Values to set :  3
 653          *  -----------------------------------------------------------
 654          */
 655         WID_11N_OBSS_NONHT_DETECTION    = 0x0084,
 656
 657         /*
 658          *  11n HT Protection Type
 659          *  -----------------------------------------------------------
 660          *  Configuration :  RTS-CTS   First Frame Exchange at non-HT-rate
 661          *  Values to set :  0         1
 662          *  Configuration :  LSIG TXOP First Frame Exchange in Mixed Fmt
 663          *  Values to set :  2         3
 664          *  -----------------------------------------------------------
 665          */
 666         WID_11N_HT_PROT_TYPE            = 0x0085,
 667
 668         /*
 669          *  11n RIFS Protection Enable Flag
 670          *  -----------------------------------------------------------
 671          *  Configuration :  Disable    Enable
 672          *  Values to set :  0          1
 673          *  -----------------------------------------------------------
 674          */
 675         WID_11N_RIFS_PROT_ENABLE        = 0x0086,
 676
 677         /*
 678          *  SMPS Mode
 679          *  -----------------------------------------------------------
 680          *  Configuration :  Static   Dynamic   MIMO (Power Save Disabled)
 681          *  Values to set :  1        2         3
 682          *  -----------------------------------------------------------
 683          */
 684         WID_11N_SMPS_MODE               = 0x0087,
 685
 686         /*
 687          *  Current transmit MCS
 688          *  -----------------------------------------------------------
 689          *  Configuration :  MCS Index for data rate
 690          *  Values to set :  0 to 7
 691          *  -----------------------------------------------------------
 692          */
 693         WID_11N_CURRENT_TX_MCS          = 0x0088,
 694
 695         WID_11N_PRINT_STATS             = 0x0089,
 696
 697         /*
 698          *  11n Short GI Enable Flag
 699          *  -----------------------------------------------------------
 700          *  Configuration :  Disable    Enable
 701          *  Values to set :  0          1
 702          *  -----------------------------------------------------------
 703          */
 704         WID_11N_SHORT_GI_ENABLE         = 0x008D,
 705
 706         /*
 707          *  11n RIFS Enable Flag
 708          *  -----------------------------------------------------------
 709          *  Configuration :  Disable    Enable
 710          *  Values to set :  0          1
 711          *  -----------------------------------------------------------
 712          */
 713         WID_RIFS_MODE                   = 0x0094,
 714
 715         /*
 716          *  TX Abort Feature
 717          *  -----------------------------------------------------------
 718          *  Configuration :  Disable Self CTS    Enable Self CTS
 719          *  Values to set :             0                      1
 720          *  Configuration :  Disable TX Abort    Enable TX Abort
 721          *  Values to set :             2                      3
 722          *  Configuration :  Enable HW TX Abort Enable SW TX Abort
 723          *  Values to set :             4                      5
 724          *  -----------------------------------------------------------
 725          */
 726         WID_TX_ABORT_CONFIG             = 0x00A1,
 727
 728         WID_REG_TSSI_11B_VALUE          = 0x00A6,
 729         WID_REG_TSSI_11G_VALUE          = 0x00A7,
 730         WID_REG_TSSI_11N_VALUE          = 0x00A8,
 731         WID_TX_CALIBRATION              = 0x00A9,
 732         WID_DSCR_TSSI_11B_VALUE         = 0x00AA,
 733         WID_DSCR_TSSI_11G_VALUE         = 0x00AB,
 734         WID_DSCR_TSSI_11N_VALUE         = 0x00AC,
 735
 736         /*
 737          *  Immediate Block-Ack Support
 738          *  -----------------------------------------------------------
 739          *  Configuration : Disable                  Enable
 740          *  Values to set :    0                       1
 741          *  -----------------------------------------------------------
 742          */
 743         WID_11N_IMMEDIATE_BA_ENABLED    = 0x00AF,
 744
 745         /*
 746          *  TXOP Disable Flag
 747          *  -----------------------------------------------------------
 748          *  Configuration : Disable                  Enable
 749          *  Values to set :    1                        0
 750          *  -----------------------------------------------------------
 751          */
 752         WID_11N_TXOP_PROT_DISABLE       = 0x00B0,
 753
 754         WID_TX_POWER_LEVEL_11N          = 0x00B1,
 755
 756         /* Custom Character WID list */
 757         WID_PC_TEST_MODE                = 0x00C8,
 758         /* SCAN Complete notification WID*/
 759         WID_SCAN_COMPLETE               = 0x00C9,
 760
 761         WID_DEL_BEACON                  = 0x00CA,
 762
 763         WID_LOGTerminal_Switch          = 0x00CD,
 764         /*  EMAC Short WID list */
 765         /*  RTS Threshold */
 766         /*
 767          *  -----------------------------------------------------------
 768          *  Configuration :   Any value between 256 to 2347
 769          *  Values to set :   Same value. Default is 2347
 770          *  -----------------------------------------------------------
 771          */
 772         WID_RTS_THRESHOLD               = 0x1000,
 773
 774         /*
 775          *  Fragmentation Threshold
 776          *  -----------------------------------------------------------
 777          *  Configuration :   Any value between 256 to 2346
 778          *  Values to set :   Same value. Default is 2346
 779          *  -----------------------------------------------------------
 780          */
 781         WID_FRAG_THRESHOLD              = 0x1001,
 782
 783         WID_SHORT_RETRY_LIMIT           = 0x1002,
 784         WID_LONG_RETRY_LIMIT            = 0x1003,
 785         WID_BEACON_INTERVAL             = 0x1006,
 786         WID_MEMORY_ACCESS_16BIT         = 0x1008,
 787         WID_RX_SENSE                    = 0x100B,
 788         WID_ACTIVE_SCAN_TIME            = 0x100C,
 789         WID_PASSIVE_SCAN_TIME           = 0x100D,
 790
 791         WID_SITE_SURVEY_SCAN_TIME       = 0x100E,
 792         WID_JOIN_START_TIMEOUT          = 0x100F,
 793         WID_AUTH_TIMEOUT                = 0x1010,
 794         WID_ASOC_TIMEOUT                = 0x1011,
 795         WID_11I_PROTOCOL_TIMEOUT        = 0x1012,
 796         WID_EAPOL_RESPONSE_TIMEOUT      = 0x1013,
 797
 798         /* NMAC Short WID list */
 799         WID_11N_SIG_QUAL_VAL            = 0x1085,
 800         WID_CCA_THRESHOLD               = 0x1087,
 801
 802         /* Custom Short WID list */
 803
 804         /* EMAC Integer WID list */
 805         WID_FAILED_COUNT                = 0x2000,
 806         WID_RETRY_COUNT                 = 0x2001,
 807         WID_MULTIPLE_RETRY_COUNT        = 0x2002,
 808         WID_FRAME_DUPLICATE_COUNT       = 0x2003,
 809         WID_ACK_FAILURE_COUNT           = 0x2004,
 810         WID_RECEIVED_FRAGMENT_COUNT     = 0x2005,
 811         WID_MCAST_RECEIVED_FRAME_COUNT  = 0x2006,
 812         WID_FCS_ERROR_COUNT             = 0x2007,
 813         WID_SUCCESS_FRAME_COUNT         = 0x2008,
 814         WID_HUT_TX_COUNT                = 0x200A,
 815         WID_TX_FRAGMENT_COUNT           = 0x200B,
 816         WID_TX_MULTICAST_FRAME_COUNT    = 0x200C,
 817         WID_RTS_SUCCESS_COUNT           = 0x200D,
 818         WID_RTS_FAILURE_COUNT           = 0x200E,
 819         WID_WEP_UNDECRYPTABLE_COUNT     = 0x200F,
 820         WID_REKEY_PERIOD                = 0x2010,
 821         WID_REKEY_PACKET_COUNT          = 0x2011,
 822         WID_1X_SERV_ADDR                = 0x2012,
 823         WID_STACK_IP_ADDR               = 0x2013,
 824         WID_STACK_NETMASK_ADDR          = 0x2014,
 825         WID_HW_RX_COUNT                 = 0x2015,
 826         WID_MEMORY_ADDRESS              = 0x201E,
 827         WID_MEMORY_ACCESS_32BIT         = 0x201F,
 828         WID_RF_REG_VAL                  = 0x2021,
 829
 830         /* NMAC Integer WID list */
 831         WID_11N_PHY_ACTIVE_REG_VAL      = 0x2080,
 832
 833         /* Custom Integer WID list */
 834         WID_GET_INACTIVE_TIME           = 0x2084,
 835         WID_SET_DRV_HANDLER             = 0X2085,
 836         WID_SET_OPERATION_MODE          = 0X2086,
 837         /* EMAC String WID list */
 838         WID_SSID                        = 0x3000,
 839         WID_FIRMWARE_VERSION            = 0x3001,
 840         WID_OPERATIONAL_RATE_SET        = 0x3002,
 841         WID_BSSID                       = 0x3003,
 842         WID_WEP_KEY_VALUE               = 0x3004,
 843         WID_11I_PSK                     = 0x3008,
 844         WID_11E_P_ACTION_REQ            = 0x3009,
 845         WID_1X_KEY                      = 0x300A,
 846         WID_HARDWARE_VERSION            = 0x300B,
 847         WID_MAC_ADDR                    = 0x300C,
 848         WID_HUT_DEST_ADDR               = 0x300D,
 849         WID_PHY_VERSION                 = 0x300F,
 850         WID_SUPP_USERNAME               = 0x3010,
 851         WID_SUPP_PASSWORD               = 0x3011,
 852         WID_SITE_SURVEY_RESULTS         = 0x3012,
 853         WID_RX_POWER_LEVEL              = 0x3013,
 854         WID_DEL_ALL_RX_BA               = 0x3014,
 855         WID_SET_STA_MAC_INACTIVE_TIME   = 0x3017,
 856         WID_ADD_WEP_KEY                 = 0x3019,
 857         WID_REMOVE_WEP_KEY              = 0x301A,
 858         WID_ADD_PTK                     = 0x301B,
 859         WID_ADD_RX_GTK                  = 0x301C,
 860         WID_ADD_TX_GTK                  = 0x301D,
 861         WID_REMOVE_KEY                  = 0x301E,
 862         WID_ASSOC_REQ_INFO              = 0x301F,
 863         WID_ASSOC_RES_INFO              = 0x3020,
 864         WID_MANUFACTURER                = 0x3026, /*Added for CAPI tool */
 865         WID_MODEL_NAME                  = 0x3027, /*Added for CAPI tool */
 866         WID_MODEL_NUM                   = 0x3028, /*Added for CAPI tool */
 867         WID_DEVICE_NAME                 = 0x3029, /*Added for CAPI tool */
 868
 869         /* NMAC String WID list */
 870         WID_11N_P_ACTION_REQ            = 0x3080,
 871         WID_HUT_TEST_ID                 = 0x3081,
 872         WID_PMKID_INFO                  = 0x3082,
 873         WID_FIRMWARE_INFO               = 0x3083,
 874         WID_REGISTER_FRAME              = 0x3084,
 875         WID_DEL_ALL_STA                 = 0x3085,
 876         WID_REMAIN_ON_CHAN              = 0x3996,
 877         WID_SSID_PROBE_REQ              = 0x3997,
 878         WID_JOIN_REQ_EXTENDED           = 0x3998,
 879
 880         WID_IP_ADDRESS                  = 0x3999,
 881
 882         /* Custom String WID list */
 883
 884         /* EMAC Binary WID list */
 885         WID_UAPSD_CONFIG                = 0x4001,
 886         WID_UAPSD_STATUS                = 0x4002,
 887         WID_WMM_AP_AC_PARAMS            = 0x4003,
 888         WID_WMM_STA_AC_PARAMS           = 0x4004,
 889         WID_NETWORK_INFO                = 0x4005,
 890         WID_STA_JOIN_INFO               = 0x4006,
 891         WID_CONNECTED_STA_LIST          = 0x4007,
 892
 893         /* NMAC Binary WID list */
 894         WID_11N_AUTORATE_TABLE          = 0x4080,
 895
 896         WID_SCAN_CHANNEL_LIST           = 0x4084,
 897
 898         WID_INFO_ELEMENT_PROBE          = 0x4085,
 899         WID_INFO_ELEMENT_ASSOCIATE      = 0x4086,
 900         WID_ADD_STA                     = 0X4087,
 901         WID_REMOVE_STA                  = 0X4088,
 902         WID_EDIT_STA                    = 0X4089,
 903         WID_ADD_BEACON                  = 0x408a,
 904
 905         WID_SETUP_MULTICAST_FILTER      = 0x408b,
 906
 907         /* Miscellaneous WIDs */
 908         WID_ALL                         = 0x7FFE,
 909         WID_MAX                         = 0xFFFF
 910 } WID_T;
 911
 912 struct wilc;
 913 int wilc_wlan_init(struct net_device *dev);
 914 void wilc_bus_set_max_speed(void);
 915 void wilc_bus_set_default_speed(void);
 916 u32 wilc_get_chipid(struct wilc *wilc, u8 update);
 917
 918 #endif