drivers/tty/serial/fsl_lpuart.c

   1 /*
   2  *  Freescale lpuart serial port driver
   3  *
   4  *  Copyright 2012-2014 Freescale Semiconductor, Inc.
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or
   9  * (at your option) any later version.
  10  */
  11
  12 #if defined(CONFIG_SERIAL_FSL_LPUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  13 #define SUPPORT_SYSRQ
  14 #endif
  15
  16 #include <linux/clk.h>
  17 #include <linux/console.h>
  18 #include <linux/dma-mapping.h>
  19 #include <linux/dmaengine.h>
  20 #include <linux/dmapool.h>
  21 #include <linux/io.h>
  22 #include <linux/irq.h>
  23 #include <linux/module.h>
  24 #include <linux/of.h>
  25 #include <linux/of_device.h>
  26 #include <linux/of_dma.h>
  27 #include <linux/serial_core.h>
  28 #include <linux/slab.h>
  29 #include <linux/tty_flip.h>
  30
  31 /* All registers are 8-bit width */
  32 #define UARTBDH                 0x00
  33 #define UARTBDL                 0x01
  34 #define UARTCR1                 0x02
  35 #define UARTCR2                 0x03
  36 #define UARTSR1                 0x04
  37 #define UARTCR3                 0x06
  38 #define UARTDR                  0x07
  39 #define UARTCR4                 0x0a
  40 #define UARTCR5                 0x0b
  41 #define UARTMODEM               0x0d
  42 #define UARTPFIFO               0x10
  43 #define UARTCFIFO               0x11
  44 #define UARTSFIFO               0x12
  45 #define UARTTWFIFO              0x13
  46 #define UARTTCFIFO              0x14
  47 #define UARTRWFIFO              0x15
  48
  49 #define UARTBDH_LBKDIE          0x80
  50 #define UARTBDH_RXEDGIE         0x40
  51 #define UARTBDH_SBR_MASK        0x1f
  52
  53 #define UARTCR1_LOOPS           0x80
  54 #define UARTCR1_RSRC            0x20
  55 #define UARTCR1_M               0x10
  56 #define UARTCR1_WAKE            0x08
  57 #define UARTCR1_ILT             0x04
  58 #define UARTCR1_PE              0x02
  59 #define UARTCR1_PT              0x01
  60
  61 #define UARTCR2_TIE             0x80
  62 #define UARTCR2_TCIE            0x40
  63 #define UARTCR2_RIE             0x20
  64 #define UARTCR2_ILIE            0x10
  65 #define UARTCR2_TE              0x08
  66 #define UARTCR2_RE              0x04
  67 #define UARTCR2_RWU             0x02
  68 #define UARTCR2_SBK             0x01
  69
  70 #define UARTSR1_TDRE            0x80
  71 #define UARTSR1_TC              0x40
  72 #define UARTSR1_RDRF            0x20
  73 #define UARTSR1_IDLE            0x10
  74 #define UARTSR1_OR              0x08
  75 #define UARTSR1_NF              0x04
  76 #define UARTSR1_FE              0x02
  77 #define UARTSR1_PE              0x01
  78
  79 #define UARTCR3_R8              0x80
  80 #define UARTCR3_T8              0x40
  81 #define UARTCR3_TXDIR           0x20
  82 #define UARTCR3_TXINV           0x10
  83 #define UARTCR3_ORIE            0x08
  84 #define UARTCR3_NEIE            0x04
  85 #define UARTCR3_FEIE            0x02
  86 #define UARTCR3_PEIE            0x01
  87
  88 #define UARTCR4_MAEN1           0x80
  89 #define UARTCR4_MAEN2           0x40
  90 #define UARTCR4_M10             0x20
  91 #define UARTCR4_BRFA_MASK       0x1f
  92 #define UARTCR4_BRFA_OFF        0
  93
  94 #define UARTCR5_TDMAS           0x80
  95 #define UARTCR5_RDMAS           0x20
  96
  97 #define UARTMODEM_RXRTSE        0x08
  98 #define UARTMODEM_TXRTSPOL      0x04
  99 #define UARTMODEM_TXRTSE        0x02
 100 #define UARTMODEM_TXCTSE        0x01
 101
 102 #define UARTPFIFO_TXFE          0x80
 103 #define UARTPFIFO_FIFOSIZE_MASK 0x7
 104 #define UARTPFIFO_TXSIZE_OFF    4
 105 #define UARTPFIFO_RXFE          0x08
 106 #define UARTPFIFO_RXSIZE_OFF    0
 107
 108 #define UARTCFIFO_TXFLUSH       0x80
 109 #define UARTCFIFO_RXFLUSH       0x40
 110 #define UARTCFIFO_RXOFE         0x04
 111 #define UARTCFIFO_TXOFE         0x02
 112 #define UARTCFIFO_RXUFE         0x01
 113
 114 #define UARTSFIFO_TXEMPT        0x80
 115 #define UARTSFIFO_RXEMPT        0x40
 116 #define UARTSFIFO_RXOF          0x04
 117 #define UARTSFIFO_TXOF          0x02
 118 #define UARTSFIFO_RXUF          0x01
 119
 120 /* 32-bit register defination */
 121 #define UARTBAUD                0x00
 122 #define UARTSTAT                0x04
 123 #define UARTCTRL                0x08
 124 #define UARTDATA                0x0C
 125 #define UARTMATCH               0x10
 126 #define UARTMODIR               0x14
 127 #define UARTFIFO                0x18
 128 #define UARTWATER               0x1c
 129
 130 #define UARTBAUD_MAEN1          0x80000000
 131 #define UARTBAUD_MAEN2          0x40000000
 132 #define UARTBAUD_M10            0x20000000
 133 #define UARTBAUD_TDMAE          0x00800000
 134 #define UARTBAUD_RDMAE          0x00200000
 135 #define UARTBAUD_MATCFG         0x00400000
 136 #define UARTBAUD_BOTHEDGE       0x00020000
 137 #define UARTBAUD_RESYNCDIS      0x00010000
 138 #define UARTBAUD_LBKDIE         0x00008000
 139 #define UARTBAUD_RXEDGIE        0x00004000
 140 #define UARTBAUD_SBNS           0x00002000
 141 #define UARTBAUD_SBR            0x00000000
 142 #define UARTBAUD_SBR_MASK       0x1fff
 143
 144 #define UARTSTAT_LBKDIF         0x80000000
 145 #define UARTSTAT_RXEDGIF        0x40000000
 146 #define UARTSTAT_MSBF           0x20000000
 147 #define UARTSTAT_RXINV          0x10000000
 148 #define UARTSTAT_RWUID          0x08000000
 149 #define UARTSTAT_BRK13          0x04000000
 150 #define UARTSTAT_LBKDE          0x02000000
 151 #define UARTSTAT_RAF            0x01000000
 152 #define UARTSTAT_TDRE           0x00800000
 153 #define UARTSTAT_TC             0x00400000
 154 #define UARTSTAT_RDRF           0x00200000
 155 #define UARTSTAT_IDLE           0x00100000
 156 #define UARTSTAT_OR             0x00080000
 157 #define UARTSTAT_NF             0x00040000
 158 #define UARTSTAT_FE             0x00020000
 159 #define UARTSTAT_PE             0x00010000
 160 #define UARTSTAT_MA1F           0x00008000
 161 #define UARTSTAT_M21F           0x00004000
 162
 163 #define UARTCTRL_R8T9           0x80000000
 164 #define UARTCTRL_R9T8           0x40000000
 165 #define UARTCTRL_TXDIR          0x20000000
 166 #define UARTCTRL_TXINV          0x10000000
 167 #define UARTCTRL_ORIE           0x08000000
 168 #define UARTCTRL_NEIE           0x04000000
 169 #define UARTCTRL_FEIE           0x02000000
 170 #define UARTCTRL_PEIE           0x01000000
 171 #define UARTCTRL_TIE            0x00800000
 172 #define UARTCTRL_TCIE           0x00400000
 173 #define UARTCTRL_RIE            0x00200000
 174 #define UARTCTRL_ILIE           0x00100000
 175 #define UARTCTRL_TE             0x00080000
 176 #define UARTCTRL_RE             0x00040000
 177 #define UARTCTRL_RWU            0x00020000
 178 #define UARTCTRL_SBK            0x00010000
 179 #define UARTCTRL_MA1IE          0x00008000
 180 #define UARTCTRL_MA2IE          0x00004000
 181 #define UARTCTRL_IDLECFG        0x00000100
 182 #define UARTCTRL_LOOPS          0x00000080
 183 #define UARTCTRL_DOZEEN         0x00000040
 184 #define UARTCTRL_RSRC           0x00000020
 185 #define UARTCTRL_M              0x00000010
 186 #define UARTCTRL_WAKE           0x00000008
 187 #define UARTCTRL_ILT            0x00000004
 188 #define UARTCTRL_PE             0x00000002
 189 #define UARTCTRL_PT             0x00000001
 190
 191 #define UARTDATA_NOISY          0x00008000
 192 #define UARTDATA_PARITYE        0x00004000
 193 #define UARTDATA_FRETSC         0x00002000
 194 #define UARTDATA_RXEMPT         0x00001000
 195 #define UARTDATA_IDLINE         0x00000800
 196 #define UARTDATA_MASK           0x3ff
 197
 198 #define UARTMODIR_IREN          0x00020000
 199 #define UARTMODIR_TXCTSSRC      0x00000020
 200 #define UARTMODIR_TXCTSC        0x00000010
 201 #define UARTMODIR_RXRTSE        0x00000008
 202 #define UARTMODIR_TXRTSPOL      0x00000004
 203 #define UARTMODIR_TXRTSE        0x00000002
 204 #define UARTMODIR_TXCTSE        0x00000001
 205
 206 #define UARTFIFO_TXEMPT         0x00800000
 207 #define UARTFIFO_RXEMPT         0x00400000
 208 #define UARTFIFO_TXOF           0x00020000
 209 #define UARTFIFO_RXUF           0x00010000
 210 #define UARTFIFO_TXFLUSH        0x00008000
 211 #define UARTFIFO_RXFLUSH        0x00004000
 212 #define UARTFIFO_TXOFE          0x00000200
 213 #define UARTFIFO_RXUFE          0x00000100
 214 #define UARTFIFO_TXFE           0x00000080
 215 #define UARTFIFO_FIFOSIZE_MASK  0x7
 216 #define UARTFIFO_TXSIZE_OFF     4
 217 #define UARTFIFO_RXFE           0x00000008
 218 #define UARTFIFO_RXSIZE_OFF     0
 219
 220 #define UARTWATER_COUNT_MASK    0xff
 221 #define UARTWATER_TXCNT_OFF     8
 222 #define UARTWATER_RXCNT_OFF     24
 223 #define UARTWATER_WATER_MASK    0xff
 224 #define UARTWATER_TXWATER_OFF   0
 225 #define UARTWATER_RXWATER_OFF   16
 226
 227 /* Rx DMA timeout in ms, which is used to calculate Rx ring buffer size */
 228 #define DMA_RX_TIMEOUT          (10)
 229
 230 #define DRIVER_NAME     "fsl-lpuart"
 231 #define DEV_NAME        "ttyLP"
 232 #define UART_NR         6
 233
 234 struct lpuart_port {
 235         struct uart_port        port;
 236         struct clk              *clk;
 237         unsigned int            txfifo_size;
 238         unsigned int            rxfifo_size;
 239         bool                    lpuart32;
 240
 241         bool                    lpuart_dma_tx_use;
 242         bool                    lpuart_dma_rx_use;
 243         struct dma_chan         *dma_tx_chan;
 244         struct dma_chan         *dma_rx_chan;
 245         struct dma_async_tx_descriptor  *dma_tx_desc;
 246         struct dma_async_tx_descriptor  *dma_rx_desc;
 247         dma_cookie_t            dma_tx_cookie;
 248         dma_cookie_t            dma_rx_cookie;
 249         unsigned int            dma_tx_bytes;
 250         unsigned int            dma_rx_bytes;
 251         bool                    dma_tx_in_progress;
 252         unsigned int            dma_rx_timeout;
 253         struct timer_list       lpuart_timer;
 254         struct scatterlist      rx_sgl, tx_sgl[2];
 255         struct circ_buf         rx_ring;
 256         int                     rx_dma_rng_buf_len;
 257         unsigned int            dma_tx_nents;
 258         wait_queue_head_t       dma_wait;
 259 };
 260
 261 static const struct of_device_id lpuart_dt_ids[] = {
 262         {
 263                 .compatible = "fsl,vf610-lpuart",
 264         },
 265         {
 266                 .compatible = "fsl,ls1021a-lpuart",
 267         },
 268         { /* sentinel */ }
 269 };
 270 MODULE_DEVICE_TABLE(of, lpuart_dt_ids);
 271
 272 /* Forward declare this for the dma callbacks*/
 273 static void lpuart_dma_tx_complete(void *arg);
 274
 275 static u32 lpuart32_read(void __iomem *addr)
 276 {
 277         return ioread32be(addr);
 278 }
 279
 280 static void lpuart32_write(u32 val, void __iomem *addr)
 281 {
 282         iowrite32be(val, addr);
 283 }
 284
 285 static void lpuart_stop_tx(struct uart_port *port)
 286 {
 287         unsigned char temp;
 288
 289         temp = readb(port->membase + UARTCR2);
 290         temp &= ~(UARTCR2_TIE | UARTCR2_TCIE);
 291         writeb(temp, port->membase + UARTCR2);
 292 }
 293
 294 static void lpuart32_stop_tx(struct uart_port *port)
 295 {
 296         unsigned long temp;
 297
 298         temp = lpuart32_read(port->membase + UARTCTRL);
 299         temp &= ~(UARTCTRL_TIE | UARTCTRL_TCIE);
 300         lpuart32_write(temp, port->membase + UARTCTRL);
 301 }
 302
 303 static void lpuart_stop_rx(struct uart_port *port)
 304 {
 305         unsigned char temp;
 306
 307         temp = readb(port->membase + UARTCR2);
 308         writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2);
 309 }
 310
 311 static void lpuart32_stop_rx(struct uart_port *port)
 312 {
 313         unsigned long temp;
 314
 315         temp = lpuart32_read(port->membase + UARTCTRL);
 316         lpuart32_write(temp & ~UARTCTRL_RE, port->membase + UARTCTRL);
 317 }
 318
 319 static void lpuart_dma_tx(struct lpuart_port *sport)
 320 {
 321         struct circ_buf *xmit = &sport->port.state->xmit;
 322         struct scatterlist *sgl = sport->tx_sgl;
 323         struct device *dev = sport->port.dev;
 324         int ret;
 325
 326         if (sport->dma_tx_in_progress)
 327                 return;
 328
 329         sport->dma_tx_bytes = uart_circ_chars_pending(xmit);
 330
 331         if (xmit->tail < xmit->head || xmit->head == 0) {
 332                 sport->dma_tx_nents = 1;
 333                 sg_init_one(sgl, xmit->buf + xmit->tail, sport->dma_tx_bytes);
 334         } else {
 335                 sport->dma_tx_nents = 2;
 336                 sg_init_table(sgl, 2);
 337                 sg_set_buf(sgl, xmit->buf + xmit->tail,
 338                                 UART_XMIT_SIZE - xmit->tail);
 339                 sg_set_buf(sgl + 1, xmit->buf, xmit->head);
 340         }
 341
 342         ret = dma_map_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
 343         if (!ret) {
 344                 dev_err(dev, "DMA mapping error for TX.\n");
 345                 return;
 346         }
 347
 348         sport->dma_tx_desc = dmaengine_prep_slave_sg(sport->dma_tx_chan, sgl,
 349                                         sport->dma_tx_nents,
 350                                         DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
 351         if (!sport->dma_tx_desc) {
 352                 dma_unmap_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
 353                 dev_err(dev, "Cannot prepare TX slave DMA!\n");
 354                 return;
 355         }
 356
 357         sport->dma_tx_desc->callback = lpuart_dma_tx_complete;
 358         sport->dma_tx_desc->callback_param = sport;
 359         sport->dma_tx_in_progress = true;
 360         sport->dma_tx_cookie = dmaengine_submit(sport->dma_tx_desc);
 361         dma_async_issue_pending(sport->dma_tx_chan);
 362 }
 363
 364 static void lpuart_dma_tx_complete(void *arg)
 365 {
 366         struct lpuart_port *sport = arg;
 367         struct scatterlist *sgl = &sport->tx_sgl[0];
 368         struct circ_buf *xmit = &sport->port.state->xmit;
 369         unsigned long flags;
 370
 371         spin_lock_irqsave(&sport->port.lock, flags);
 372
 373         dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
 374
 375         xmit->tail = (xmit->tail + sport->dma_tx_bytes) & (UART_XMIT_SIZE - 1);
 376
 377         sport->port.icount.tx += sport->dma_tx_bytes;
 378         sport->dma_tx_in_progress = false;
 379         spin_unlock_irqrestore(&sport->port.lock, flags);
 380
 381         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 382                 uart_write_wakeup(&sport->port);
 383
 384         if (waitqueue_active(&sport->dma_wait)) {
 385                 wake_up(&sport->dma_wait);
 386                 return;
 387         }
 388
 389         spin_lock_irqsave(&sport->port.lock, flags);
 390
 391         if (!uart_circ_empty(xmit) && !uart_tx_stopped(&sport->port))
 392                 lpuart_dma_tx(sport);
 393
 394         spin_unlock_irqrestore(&sport->port.lock, flags);
 395 }
 396
 397 static int lpuart_dma_tx_request(struct uart_port *port)
 398 {
 399         struct lpuart_port *sport = container_of(port,
 400                                         struct lpuart_port, port);
 401         struct dma_slave_config dma_tx_sconfig = {};
 402         int ret;
 403
 404         dma_tx_sconfig.dst_addr = sport->port.mapbase + UARTDR;
 405         dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 406         dma_tx_sconfig.dst_maxburst = 1;
 407         dma_tx_sconfig.direction = DMA_MEM_TO_DEV;
 408         ret = dmaengine_slave_config(sport->dma_tx_chan, &dma_tx_sconfig);
 409
 410         if (ret) {
 411                 dev_err(sport->port.dev,
 412                                 "DMA slave config failed, err = %d\n", ret);
 413                 return ret;
 414         }
 415
 416         return 0;
 417 }
 418
 419 static void lpuart_flush_buffer(struct uart_port *port)
 420 {
 421         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
 422
 423         if (sport->lpuart_dma_tx_use) {
 424                 if (sport->dma_tx_in_progress) {
 425                         dma_unmap_sg(sport->port.dev, &sport->tx_sgl[0],
 426                                 sport->dma_tx_nents, DMA_TO_DEVICE);
 427                         sport->dma_tx_in_progress = false;
 428                 }
 429                 dmaengine_terminate_all(sport->dma_tx_chan);
 430         }
 431 }
 432
 433 #if defined(CONFIG_CONSOLE_POLL)
 434
 435 static int lpuart_poll_init(struct uart_port *port)
 436 {
 437         struct lpuart_port *sport = container_of(port,
 438                                         struct lpuart_port, port);
 439         unsigned long flags;
 440         unsigned char temp;
 441
 442         sport->port.fifosize = 0;
 443
 444         spin_lock_irqsave(&sport->port.lock, flags);
 445         /* Disable Rx & Tx */
 446         writeb(0, sport->port.membase + UARTCR2);
 447
 448         temp = readb(sport->port.membase + UARTPFIFO);
 449         /* Enable Rx and Tx FIFO */
 450         writeb(temp | UARTPFIFO_RXFE | UARTPFIFO_TXFE,
 451                         sport->port.membase + UARTPFIFO);
 452
 453         /* flush Tx and Rx FIFO */
 454         writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH,
 455                         sport->port.membase + UARTCFIFO);
 456
 457         /* explicitly clear RDRF */
 458         if (readb(sport->port.membase + UARTSR1) & UARTSR1_RDRF) {
 459                 readb(sport->port.membase + UARTDR);
 460                 writeb(UARTSFIFO_RXUF, sport->port.membase + UARTSFIFO);
 461         }
 462
 463         writeb(0, sport->port.membase + UARTTWFIFO);
 464         writeb(1, sport->port.membase + UARTRWFIFO);
 465
 466         /* Enable Rx and Tx */
 467         writeb(UARTCR2_RE | UARTCR2_TE, sport->port.membase + UARTCR2);
 468         spin_unlock_irqrestore(&sport->port.lock, flags);
 469
 470         return 0;
 471 }
 472
 473 static void lpuart_poll_put_char(struct uart_port *port, unsigned char c)
 474 {
 475         /* drain */
 476         while (!(readb(port->membase + UARTSR1) & UARTSR1_TDRE))
 477                 barrier();
 478
 479         writeb(c, port->membase + UARTDR);
 480 }
 481
 482 static int lpuart_poll_get_char(struct uart_port *port)
 483 {
 484         if (!(readb(port->membase + UARTSR1) & UARTSR1_RDRF))
 485                 return NO_POLL_CHAR;
 486
 487         return readb(port->membase + UARTDR);
 488 }
 489
 490 #endif
 491
 492 static inline void lpuart_transmit_buffer(struct lpuart_port *sport)
 493 {
 494         struct circ_buf *xmit = &sport->port.state->xmit;
 495
 496         while (!uart_circ_empty(xmit) &&
 497                 (readb(sport->port.membase + UARTTCFIFO) < sport->txfifo_size)) {
 498                 writeb(xmit->buf[xmit->tail], sport->port.membase + UARTDR);
 499                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 500                 sport->port.icount.tx++;
 501         }
 502
 503         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 504                 uart_write_wakeup(&sport->port);
 505
 506         if (uart_circ_empty(xmit))
 507                 lpuart_stop_tx(&sport->port);
 508 }
 509
 510 static inline void lpuart32_transmit_buffer(struct lpuart_port *sport)
 511 {
 512         struct circ_buf *xmit = &sport->port.state->xmit;
 513         unsigned long txcnt;
 514
 515         txcnt = lpuart32_read(sport->port.membase + UARTWATER);
 516         txcnt = txcnt >> UARTWATER_TXCNT_OFF;
 517         txcnt &= UARTWATER_COUNT_MASK;
 518         while (!uart_circ_empty(xmit) && (txcnt < sport->txfifo_size)) {
 519                 lpuart32_write(xmit->buf[xmit->tail], sport->port.membase + UARTDATA);
 520                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 521                 sport->port.icount.tx++;
 522                 txcnt = lpuart32_read(sport->port.membase + UARTWATER);
 523                 txcnt = txcnt >> UARTWATER_TXCNT_OFF;
 524                 txcnt &= UARTWATER_COUNT_MASK;
 525         }
 526
 527         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 528                 uart_write_wakeup(&sport->port);
 529
 530         if (uart_circ_empty(xmit))
 531                 lpuart32_stop_tx(&sport->port);
 532 }
 533
 534 static void lpuart_start_tx(struct uart_port *port)
 535 {
 536         struct lpuart_port *sport = container_of(port,
 537                         struct lpuart_port, port);
 538         struct circ_buf *xmit = &sport->port.state->xmit;
 539         unsigned char temp;
 540
 541         temp = readb(port->membase + UARTCR2);
 542         writeb(temp | UARTCR2_TIE, port->membase + UARTCR2);
 543
 544         if (sport->lpuart_dma_tx_use) {
 545                 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port))
 546                         lpuart_dma_tx(sport);
 547         } else {
 548                 if (readb(port->membase + UARTSR1) & UARTSR1_TDRE)
 549                         lpuart_transmit_buffer(sport);
 550         }
 551 }
 552
 553 static void lpuart32_start_tx(struct uart_port *port)
 554 {
 555         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
 556         unsigned long temp;
 557
 558         temp = lpuart32_read(port->membase + UARTCTRL);
 559         lpuart32_write(temp | UARTCTRL_TIE, port->membase + UARTCTRL);
 560
 561         if (lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TDRE)
 562                 lpuart32_transmit_buffer(sport);
 563 }
 564
 565 /* return TIOCSER_TEMT when transmitter is not busy */
 566 static unsigned int lpuart_tx_empty(struct uart_port *port)
 567 {
 568         struct lpuart_port *sport = container_of(port,
 569                         struct lpuart_port, port);
 570         unsigned char sr1 = readb(port->membase + UARTSR1);
 571         unsigned char sfifo = readb(port->membase + UARTSFIFO);
 572
 573         if (sport->dma_tx_in_progress)
 574                 return 0;
 575
 576         if (sr1 & UARTSR1_TC && sfifo & UARTSFIFO_TXEMPT)
 577                 return TIOCSER_TEMT;
 578
 579         return 0;
 580 }
 581
 582 static unsigned int lpuart32_tx_empty(struct uart_port *port)
 583 {
 584         return (lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TC) ?
 585                 TIOCSER_TEMT : 0;
 586 }
 587
 588 static irqreturn_t lpuart_txint(int irq, void *dev_id)
 589 {
 590         struct lpuart_port *sport = dev_id;
 591         struct circ_buf *xmit = &sport->port.state->xmit;
 592         unsigned long flags;
 593
 594         spin_lock_irqsave(&sport->port.lock, flags);
 595         if (sport->port.x_char) {
 596                 if (sport->lpuart32)
 597                         lpuart32_write(sport->port.x_char, sport->port.membase + UARTDATA);
 598                 else
 599                         writeb(sport->port.x_char, sport->port.membase + UARTDR);
 600                 goto out;
 601         }
 602
 603         if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
 604                 if (sport->lpuart32)
 605                         lpuart32_stop_tx(&sport->port);
 606                 else
 607                         lpuart_stop_tx(&sport->port);
 608                 goto out;
 609         }
 610
 611         if (sport->lpuart32)
 612                 lpuart32_transmit_buffer(sport);
 613         else
 614                 lpuart_transmit_buffer(sport);
 615
 616         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 617                 uart_write_wakeup(&sport->port);
 618
 619 out:
 620         spin_unlock_irqrestore(&sport->port.lock, flags);
 621         return IRQ_HANDLED;
 622 }
 623
 624 static irqreturn_t lpuart_rxint(int irq, void *dev_id)
 625 {
 626         struct lpuart_port *sport = dev_id;
 627         unsigned int flg, ignored = 0;
 628         struct tty_port *port = &sport->port.state->port;
 629         unsigned long flags;
 630         unsigned char rx, sr;
 631
 632         spin_lock_irqsave(&sport->port.lock, flags);
 633
 634         while (!(readb(sport->port.membase + UARTSFIFO) & UARTSFIFO_RXEMPT)) {
 635                 flg = TTY_NORMAL;
 636                 sport->port.icount.rx++;
 637                 /*
 638                  * to clear the FE, OR, NF, FE, PE flags,
 639                  * read SR1 then read DR
 640                  */
 641                 sr = readb(sport->port.membase + UARTSR1);
 642                 rx = readb(sport->port.membase + UARTDR);
 643
 644                 if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
 645                         continue;
 646
 647                 if (sr & (UARTSR1_PE | UARTSR1_OR | UARTSR1_FE)) {
 648                         if (sr & UARTSR1_PE)
 649                                 sport->port.icount.parity++;
 650                         else if (sr & UARTSR1_FE)
 651                                 sport->port.icount.frame++;
 652
 653                         if (sr & UARTSR1_OR)
 654                                 sport->port.icount.overrun++;
 655
 656                         if (sr & sport->port.ignore_status_mask) {
 657                                 if (++ignored > 100)
 658                                         goto out;
 659                                 continue;
 660                         }
 661
 662                         sr &= sport->port.read_status_mask;
 663
 664                         if (sr & UARTSR1_PE)
 665                                 flg = TTY_PARITY;
 666                         else if (sr & UARTSR1_FE)
 667                                 flg = TTY_FRAME;
 668
 669                         if (sr & UARTSR1_OR)
 670                                 flg = TTY_OVERRUN;
 671
 672 #ifdef SUPPORT_SYSRQ
 673                         sport->port.sysrq = 0;
 674 #endif
 675                 }
 676
 677                 tty_insert_flip_char(port, rx, flg);
 678         }
 679
 680 out:
 681         spin_unlock_irqrestore(&sport->port.lock, flags);
 682
 683         tty_flip_buffer_push(port);
 684         return IRQ_HANDLED;
 685 }
 686
 687 static irqreturn_t lpuart32_rxint(int irq, void *dev_id)
 688 {
 689         struct lpuart_port *sport = dev_id;
 690         unsigned int flg, ignored = 0;
 691         struct tty_port *port = &sport->port.state->port;
 692         unsigned long flags;
 693         unsigned long rx, sr;
 694
 695         spin_lock_irqsave(&sport->port.lock, flags);
 696
 697         while (!(lpuart32_read(sport->port.membase + UARTFIFO) & UARTFIFO_RXEMPT)) {
 698                 flg = TTY_NORMAL;
 699                 sport->port.icount.rx++;
 700                 /*
 701                  * to clear the FE, OR, NF, FE, PE flags,
 702                  * read STAT then read DATA reg
 703                  */
 704                 sr = lpuart32_read(sport->port.membase + UARTSTAT);
 705                 rx = lpuart32_read(sport->port.membase + UARTDATA);
 706                 rx &= 0x3ff;
 707
 708                 if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
 709                         continue;
 710
 711                 if (sr & (UARTSTAT_PE | UARTSTAT_OR | UARTSTAT_FE)) {
 712                         if (sr & UARTSTAT_PE)
 713                                 sport->port.icount.parity++;
 714                         else if (sr & UARTSTAT_FE)
 715                                 sport->port.icount.frame++;
 716
 717                         if (sr & UARTSTAT_OR)
 718                                 sport->port.icount.overrun++;
 719
 720                         if (sr & sport->port.ignore_status_mask) {
 721                                 if (++ignored > 100)
 722                                         goto out;
 723                                 continue;
 724                         }
 725
 726                         sr &= sport->port.read_status_mask;
 727
 728                         if (sr & UARTSTAT_PE)
 729                                 flg = TTY_PARITY;
 730                         else if (sr & UARTSTAT_FE)
 731                                 flg = TTY_FRAME;
 732
 733                         if (sr & UARTSTAT_OR)
 734                                 flg = TTY_OVERRUN;
 735
 736 #ifdef SUPPORT_SYSRQ
 737                         sport->port.sysrq = 0;
 738 #endif
 739                 }
 740
 741                 tty_insert_flip_char(port, rx, flg);
 742         }
 743
 744 out:
 745         spin_unlock_irqrestore(&sport->port.lock, flags);
 746
 747         tty_flip_buffer_push(port);
 748         return IRQ_HANDLED;
 749 }
 750
 751 static irqreturn_t lpuart_int(int irq, void *dev_id)
 752 {
 753         struct lpuart_port *sport = dev_id;
 754         unsigned char sts;
 755
 756         sts = readb(sport->port.membase + UARTSR1);
 757
 758         if (sts & UARTSR1_RDRF)
 759                 lpuart_rxint(irq, dev_id);
 760
 761         if (sts & UARTSR1_TDRE)
 762                 lpuart_txint(irq, dev_id);
 763
 764         return IRQ_HANDLED;
 765 }
 766
 767 static irqreturn_t lpuart32_int(int irq, void *dev_id)
 768 {
 769         struct lpuart_port *sport = dev_id;
 770         unsigned long sts, rxcount;
 771
 772         sts = lpuart32_read(sport->port.membase + UARTSTAT);
 773         rxcount = lpuart32_read(sport->port.membase + UARTWATER);
 774         rxcount = rxcount >> UARTWATER_RXCNT_OFF;
 775
 776         if (sts & UARTSTAT_RDRF || rxcount > 0)
 777                 lpuart32_rxint(irq, dev_id);
 778
 779         if ((sts & UARTSTAT_TDRE) &&
 780                 !(lpuart32_read(sport->port.membase + UARTBAUD) & UARTBAUD_TDMAE))
 781                 lpuart_txint(irq, dev_id);
 782
 783         lpuart32_write(sts, sport->port.membase + UARTSTAT);
 784         return IRQ_HANDLED;
 785 }
 786
 787 static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
 788 {
 789         struct tty_port *port = &sport->port.state->port;
 790         struct dma_tx_state state;
 791         enum dma_status dmastat;
 792         struct circ_buf *ring = &sport->rx_ring;
 793         unsigned long flags;
 794         int count = 0;
 795         unsigned char sr;
 796
 797         sr = readb(sport->port.membase + UARTSR1);
 798
 799         if (sr & (UARTSR1_PE | UARTSR1_FE)) {
 800                 /* Read DR to clear the error flags */
 801                 readb(sport->port.membase + UARTDR);
 802
 803                 if (sr & UARTSR1_PE)
 804                     sport->port.icount.parity++;
 805                 else if (sr & UARTSR1_FE)
 806                     sport->port.icount.frame++;
 807         }
 808
 809         async_tx_ack(sport->dma_rx_desc);
 810
 811         spin_lock_irqsave(&sport->port.lock, flags);
 812
 813         dmastat = dmaengine_tx_status(sport->dma_rx_chan,
 814                                 sport->dma_rx_cookie,
 815                                 &state);
 816
 817         if (dmastat == DMA_ERROR) {
 818                 dev_err(sport->port.dev, "Rx DMA transfer failed!\n");
 819                 spin_unlock_irqrestore(&sport->port.lock, flags);
 820                 return;
 821         }
 822
 823         /* CPU claims ownership of RX DMA buffer */
 824         dma_sync_sg_for_cpu(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
 825
 826         /*
 827          * ring->head points to the end of data already written by the DMA.
 828          * ring->tail points to the beginning of data to be read by the
 829          * framework.
 830          * The current transfer size should not be larger than the dma buffer
 831          * length.
 832          */
 833         ring->head = sport->rx_sgl.length - state.residue;
 834         BUG_ON(ring->head > sport->rx_sgl.length);
 835         /*
 836          * At this point ring->head may point to the first byte right after the
 837          * last byte of the dma buffer:
 838          * 0 <= ring->head <= sport->rx_sgl.length
 839          *
 840          * However ring->tail must always points inside the dma buffer:
 841          * 0 <= ring->tail <= sport->rx_sgl.length - 1
 842          *
 843          * Since we use a ring buffer, we have to handle the case
 844          * where head is lower than tail. In such a case, we first read from
 845          * tail to the end of the buffer then reset tail.
 846          */
 847         if (ring->head < ring->tail) {
 848                 count = sport->rx_sgl.length - ring->tail;
 849
 850                 tty_insert_flip_string(port, ring->buf + ring->tail, count);
 851                 ring->tail = 0;
 852                 sport->port.icount.rx += count;
 853         }
 854
 855         /* Finally we read data from tail to head */
 856         if (ring->tail < ring->head) {
 857                 count = ring->head - ring->tail;
 858                 tty_insert_flip_string(port, ring->buf + ring->tail, count);
 859                 /* Wrap ring->head if needed */
 860                 if (ring->head >= sport->rx_sgl.length)
 861                         ring->head = 0;
 862                 ring->tail = ring->head;
 863                 sport->port.icount.rx += count;
 864         }
 865
 866         dma_sync_sg_for_device(sport->port.dev, &sport->rx_sgl, 1,
 867                                DMA_FROM_DEVICE);
 868
 869         spin_unlock_irqrestore(&sport->port.lock, flags);
 870
 871         tty_flip_buffer_push(port);
 872         mod_timer(&sport->lpuart_timer, jiffies + sport->dma_rx_timeout);
 873 }
 874
 875 static void lpuart_dma_rx_complete(void *arg)
 876 {
 877         struct lpuart_port *sport = arg;
 878
 879         lpuart_copy_rx_to_tty(sport);
 880 }
 881
 882 static void lpuart_timer_func(unsigned long data)
 883 {
 884         struct lpuart_port *sport = (struct lpuart_port *)data;
 885
 886         lpuart_copy_rx_to_tty(sport);
 887 }
 888
 889 static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
 890 {
 891         struct dma_slave_config dma_rx_sconfig = {};
 892         struct circ_buf *ring = &sport->rx_ring;
 893         int ret, nent;
 894         int bits, baud;
 895         struct tty_struct *tty = tty_port_tty_get(&sport->port.state->port);
 896         struct ktermios *termios = &tty->termios;
 897
 898         baud = tty_get_baud_rate(tty);
 899
 900         bits = (termios->c_cflag & CSIZE) == CS7 ? 9 : 10;
 901         if (termios->c_cflag & PARENB)
 902                 bits++;
 903
 904         /*
 905          * Calculate length of one DMA buffer size to keep latency below
 906          * 10ms at any baud rate.
 907          */
 908         sport->rx_dma_rng_buf_len = (DMA_RX_TIMEOUT * baud /  bits / 1000) * 2;
 909         sport->rx_dma_rng_buf_len = (1 << (fls(sport->rx_dma_rng_buf_len) - 1));
 910         if (sport->rx_dma_rng_buf_len < 16)
 911                 sport->rx_dma_rng_buf_len = 16;
 912
 913         ring->buf = kmalloc(sport->rx_dma_rng_buf_len, GFP_ATOMIC);
 914         if (!ring->buf) {
 915                 dev_err(sport->port.dev, "Ring buf alloc failed\n");
 916                 return -ENOMEM;
 917         }
 918
 919         sg_init_one(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len);
 920         sg_set_buf(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len);
 921         nent = dma_map_sg(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
 922
 923         if (!nent) {
 924                 dev_err(sport->port.dev, "DMA Rx mapping error\n");
 925                 return -EINVAL;
 926         }
 927
 928         dma_rx_sconfig.src_addr = sport->port.mapbase + UARTDR;
 929         dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 930         dma_rx_sconfig.src_maxburst = 1;
 931         dma_rx_sconfig.direction = DMA_DEV_TO_MEM;
 932         ret = dmaengine_slave_config(sport->dma_rx_chan, &dma_rx_sconfig);
 933
 934         if (ret < 0) {
 935                 dev_err(sport->port.dev,
 936                                 "DMA Rx slave config failed, err = %d\n", ret);
 937                 return ret;
 938         }
 939
 940         sport->dma_rx_desc = dmaengine_prep_dma_cyclic(sport->dma_rx_chan,
 941                                  sg_dma_address(&sport->rx_sgl),
 942                                  sport->rx_sgl.length,
 943                                  sport->rx_sgl.length / 2,
 944                                  DMA_DEV_TO_MEM,
 945                                  DMA_PREP_INTERRUPT);
 946         if (!sport->dma_rx_desc) {
 947                 dev_err(sport->port.dev, "Cannot prepare cyclic DMA\n");
 948                 return -EFAULT;
 949         }
 950
 951         sport->dma_rx_desc->callback = lpuart_dma_rx_complete;
 952         sport->dma_rx_desc->callback_param = sport;
 953         sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc);
 954         dma_async_issue_pending(sport->dma_rx_chan);
 955
 956         writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS,
 957                                 sport->port.membase + UARTCR5);
 958
 959         return 0;
 960 }
 961
 962 static void lpuart_dma_rx_free(struct uart_port *port)
 963 {
 964         struct lpuart_port *sport = container_of(port,
 965                                         struct lpuart_port, port);
 966
 967         if (sport->dma_rx_chan)
 968                 dmaengine_terminate_all(sport->dma_rx_chan);
 969
 970         dma_unmap_sg(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
 971         kfree(sport->rx_ring.buf);
 972         sport->rx_ring.tail = 0;
 973         sport->rx_ring.head = 0;
 974         sport->dma_rx_desc = NULL;
 975         sport->dma_rx_cookie = -EINVAL;
 976 }
 977
 978 static int lpuart_config_rs485(struct uart_port *port,
 979                         struct serial_rs485 *rs485)
 980 {
 981         struct lpuart_port *sport = container_of(port,
 982                         struct lpuart_port, port);
 983
 984         u8 modem = readb(sport->port.membase + UARTMODEM) &
 985                 ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
 986         writeb(modem, sport->port.membase + UARTMODEM);
 987
 988         if (rs485->flags & SER_RS485_ENABLED) {
 989                 /* Enable auto RS-485 RTS mode */
 990                 modem |= UARTMODEM_TXRTSE;
 991
 992                 /*
 993                  * RTS needs to be logic HIGH either during transer _or_ after
 994                  * transfer, other variants are not supported by the hardware.
 995                  */
 996
 997                 if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
 998                                 SER_RS485_RTS_AFTER_SEND)))
 999                         rs485->flags |= SER_RS485_RTS_ON_SEND;
1000
1001                 if (rs485->flags & SER_RS485_RTS_ON_SEND &&
1002                                 rs485->flags & SER_RS485_RTS_AFTER_SEND)
1003                         rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
1004
1005                 /*
1006                  * The hardware defaults to RTS logic HIGH while transfer.
1007                  * Switch polarity in case RTS shall be logic HIGH
1008                  * after transfer.
1009                  * Note: UART is assumed to be active high.
1010                  */
1011                 if (rs485->flags & SER_RS485_RTS_ON_SEND)
1012                         modem &= ~UARTMODEM_TXRTSPOL;
1013                 else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
1014                         modem |= UARTMODEM_TXRTSPOL;
1015         }
1016
1017         /* Store the new configuration */
1018         sport->port.rs485 = *rs485;
1019
1020         writeb(modem, sport->port.membase + UARTMODEM);
1021         return 0;
1022 }
1023
1024 static unsigned int lpuart_get_mctrl(struct uart_port *port)
1025 {
1026         unsigned int temp = 0;
1027         unsigned char reg;
1028
1029         reg = readb(port->membase + UARTMODEM);
1030         if (reg & UARTMODEM_TXCTSE)
1031                 temp |= TIOCM_CTS;
1032
1033         if (reg & UARTMODEM_RXRTSE)
1034                 temp |= TIOCM_RTS;
1035
1036         return temp;
1037 }
1038
1039 static unsigned int lpuart32_get_mctrl(struct uart_port *port)
1040 {
1041         unsigned int temp = 0;
1042         unsigned long reg;
1043
1044         reg = lpuart32_read(port->membase + UARTMODIR);
1045         if (reg & UARTMODIR_TXCTSE)
1046                 temp |= TIOCM_CTS;
1047
1048         if (reg & UARTMODIR_RXRTSE)
1049                 temp |= TIOCM_RTS;
1050
1051         return temp;
1052 }
1053
1054 static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1055 {
1056         unsigned char temp;
1057         struct lpuart_port *sport = container_of(port,
1058                                 struct lpuart_port, port);
1059
1060         /* Make sure RXRTSE bit is not set when RS485 is enabled */
1061         if (!(sport->port.rs485.flags & SER_RS485_ENABLED)) {
1062                 temp = readb(sport->port.membase + UARTMODEM) &
1063                         ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
1064
1065                 if (mctrl & TIOCM_RTS)
1066                         temp |= UARTMODEM_RXRTSE;
1067
1068                 if (mctrl & TIOCM_CTS)
1069                         temp |= UARTMODEM_TXCTSE;
1070
1071                 writeb(temp, port->membase + UARTMODEM);
1072         }
1073 }
1074
1075 static void lpuart32_set_mctrl(struct uart_port *port, unsigned int mctrl)
1076 {
1077         unsigned long temp;
1078
1079         temp = lpuart32_read(port->membase + UARTMODIR) &
1080                         ~(UARTMODIR_RXRTSE | UARTMODIR_TXCTSE);
1081
1082         if (mctrl & TIOCM_RTS)
1083                 temp |= UARTMODIR_RXRTSE;
1084
1085         if (mctrl & TIOCM_CTS)
1086                 temp |= UARTMODIR_TXCTSE;
1087
1088         lpuart32_write(temp, port->membase + UARTMODIR);
1089 }
1090
1091 static void lpuart_break_ctl(struct uart_port *port, int break_state)
1092 {
1093         unsigned char temp;
1094
1095         temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
1096
1097         if (break_state != 0)
1098                 temp |= UARTCR2_SBK;
1099
1100         writeb(temp, port->membase + UARTCR2);
1101 }
1102
1103 static void lpuart32_break_ctl(struct uart_port *port, int break_state)
1104 {
1105         unsigned long temp;
1106
1107         temp = lpuart32_read(port->membase + UARTCTRL) & ~UARTCTRL_SBK;
1108
1109         if (break_state != 0)
1110                 temp |= UARTCTRL_SBK;
1111
1112         lpuart32_write(temp, port->membase + UARTCTRL);
1113 }
1114
1115 static void lpuart_setup_watermark(struct lpuart_port *sport)
1116 {
1117         unsigned char val, cr2;
1118         unsigned char cr2_saved;
1119
1120         cr2 = readb(sport->port.membase + UARTCR2);
1121         cr2_saved = cr2;
1122         cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_TE |
1123                         UARTCR2_RIE | UARTCR2_RE);
1124         writeb(cr2, sport->port.membase + UARTCR2);
1125
1126         val = readb(sport->port.membase + UARTPFIFO);
1127         writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
1128                         sport->port.membase + UARTPFIFO);
1129
1130         /* flush Tx and Rx FIFO */
1131         writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH,
1132                         sport->port.membase + UARTCFIFO);
1133
1134         /* explicitly clear RDRF */
1135         if (readb(sport->port.membase + UARTSR1) & UARTSR1_RDRF) {
1136                 readb(sport->port.membase + UARTDR);
1137                 writeb(UARTSFIFO_RXUF, sport->port.membase + UARTSFIFO);
1138         }
1139
1140         writeb(0, sport->port.membase + UARTTWFIFO);
1141         writeb(1, sport->port.membase + UARTRWFIFO);
1142
1143         /* Restore cr2 */
1144         writeb(cr2_saved, sport->port.membase + UARTCR2);
1145 }
1146
1147 static void lpuart32_setup_watermark(struct lpuart_port *sport)
1148 {
1149         unsigned long val, ctrl;
1150         unsigned long ctrl_saved;
1151
1152         ctrl = lpuart32_read(sport->port.membase + UARTCTRL);
1153         ctrl_saved = ctrl;
1154         ctrl &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_TE |
1155                         UARTCTRL_RIE | UARTCTRL_RE);
1156         lpuart32_write(ctrl, sport->port.membase + UARTCTRL);
1157
1158         /* enable FIFO mode */
1159         val = lpuart32_read(sport->port.membase + UARTFIFO);
1160         val |= UARTFIFO_TXFE | UARTFIFO_RXFE;
1161         val |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH;
1162         lpuart32_write(val, sport->port.membase + UARTFIFO);
1163
1164         /* set the watermark */
1165         val = (0x1 << UARTWATER_RXWATER_OFF) | (0x0 << UARTWATER_TXWATER_OFF);
1166         lpuart32_write(val, sport->port.membase + UARTWATER);
1167
1168         /* Restore cr2 */
1169         lpuart32_write(ctrl_saved, sport->port.membase + UARTCTRL);
1170 }
1171
1172 static void rx_dma_timer_init(struct lpuart_port *sport)
1173 {
1174                 setup_timer(&sport->lpuart_timer, lpuart_timer_func,
1175                                 (unsigned long)sport);
1176                 sport->lpuart_timer.expires = jiffies + sport->dma_rx_timeout;
1177                 add_timer(&sport->lpuart_timer);
1178 }
1179
1180 static int lpuart_startup(struct uart_port *port)
1181 {
1182         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1183         int ret;
1184         unsigned long flags;
1185         unsigned char temp;
1186
1187         /* determine FIFO size and enable FIFO mode */
1188         temp = readb(sport->port.membase + UARTPFIFO);
1189
1190         sport->txfifo_size = 0x1 << (((temp >> UARTPFIFO_TXSIZE_OFF) &
1191                 UARTPFIFO_FIFOSIZE_MASK) + 1);
1192
1193         sport->port.fifosize = sport->txfifo_size;
1194
1195         sport->rxfifo_size = 0x1 << (((temp >> UARTPFIFO_RXSIZE_OFF) &
1196                 UARTPFIFO_FIFOSIZE_MASK) + 1);
1197
1198         ret = devm_request_irq(port->dev, port->irq, lpuart_int, 0,
1199                                 DRIVER_NAME, sport);
1200         if (ret)
1201                 return ret;
1202
1203         spin_lock_irqsave(&sport->port.lock, flags);
1204
1205         lpuart_setup_watermark(sport);
1206
1207         temp = readb(sport->port.membase + UARTCR2);
1208         temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
1209         writeb(temp, sport->port.membase + UARTCR2);
1210
1211         if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
1212                 /* set Rx DMA timeout */
1213                 sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT);
1214                 if (!sport->dma_rx_timeout)
1215                      sport->dma_rx_timeout = 1;
1216
1217                 sport->lpuart_dma_rx_use = true;
1218                 rx_dma_timer_init(sport);
1219         } else {
1220                 sport->lpuart_dma_rx_use = false;
1221         }
1222
1223         if (sport->dma_tx_chan && !lpuart_dma_tx_request(port)) {
1224                 init_waitqueue_head(&sport->dma_wait);
1225                 sport->lpuart_dma_tx_use = true;
1226                 temp = readb(port->membase + UARTCR5);
1227                 writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
1228         } else {
1229                 sport->lpuart_dma_tx_use = false;
1230         }
1231
1232         spin_unlock_irqrestore(&sport->port.lock, flags);
1233
1234         return 0;
1235 }
1236
1237 static int lpuart32_startup(struct uart_port *port)
1238 {
1239         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1240         int ret;
1241         unsigned long flags;
1242         unsigned long temp;
1243
1244         /* determine FIFO size */
1245         temp = lpuart32_read(sport->port.membase + UARTFIFO);
1246
1247         sport->txfifo_size = 0x1 << (((temp >> UARTFIFO_TXSIZE_OFF) &
1248                 UARTFIFO_FIFOSIZE_MASK) - 1);
1249
1250         sport->rxfifo_size = 0x1 << (((temp >> UARTFIFO_RXSIZE_OFF) &
1251                 UARTFIFO_FIFOSIZE_MASK) - 1);
1252
1253         ret = devm_request_irq(port->dev, port->irq, lpuart32_int, 0,
1254                                 DRIVER_NAME, sport);
1255         if (ret)
1256                 return ret;
1257
1258         spin_lock_irqsave(&sport->port.lock, flags);
1259
1260         lpuart32_setup_watermark(sport);
1261
1262         temp = lpuart32_read(sport->port.membase + UARTCTRL);
1263         temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | UARTCTRL_TE);
1264         temp |= UARTCTRL_ILIE;
1265         lpuart32_write(temp, sport->port.membase + UARTCTRL);
1266
1267         spin_unlock_irqrestore(&sport->port.lock, flags);
1268         return 0;
1269 }
1270
1271 static void lpuart_shutdown(struct uart_port *port)
1272 {
1273         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1274         unsigned char temp;
1275         unsigned long flags;
1276
1277         spin_lock_irqsave(&port->lock, flags);
1278
1279         /* disable Rx/Tx and interrupts */
1280         temp = readb(port->membase + UARTCR2);
1281         temp &= ~(UARTCR2_TE | UARTCR2_RE |
1282                         UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
1283         writeb(temp, port->membase + UARTCR2);
1284
1285         spin_unlock_irqrestore(&port->lock, flags);
1286
1287         devm_free_irq(port->dev, port->irq, sport);
1288
1289         if (sport->lpuart_dma_rx_use) {
1290                 del_timer_sync(&sport->lpuart_timer);
1291                 lpuart_dma_rx_free(&sport->port);
1292         }
1293
1294         if (sport->lpuart_dma_tx_use) {
1295                 if (wait_event_interruptible(sport->dma_wait,
1296                         !sport->dma_tx_in_progress) != false) {
1297                         sport->dma_tx_in_progress = false;
1298                         dmaengine_terminate_all(sport->dma_tx_chan);
1299                 }
1300
1301                 lpuart_stop_tx(port);
1302         }
1303 }
1304
1305 static void lpuart32_shutdown(struct uart_port *port)
1306 {
1307         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1308         unsigned long temp;
1309         unsigned long flags;
1310
1311         spin_lock_irqsave(&port->lock, flags);
1312
1313         /* disable Rx/Tx and interrupts */
1314         temp = lpuart32_read(port->membase + UARTCTRL);
1315         temp &= ~(UARTCTRL_TE | UARTCTRL_RE |
1316                         UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE);
1317         lpuart32_write(temp, port->membase + UARTCTRL);
1318
1319         spin_unlock_irqrestore(&port->lock, flags);
1320
1321         devm_free_irq(port->dev, port->irq, sport);
1322 }
1323
1324 static void
1325 lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
1326                    struct ktermios *old)
1327 {
1328         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1329         unsigned long flags;
1330         unsigned char cr1, old_cr1, old_cr2, cr3, cr4, bdh, modem;
1331         unsigned int  baud;
1332         unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
1333         unsigned int sbr, brfa;
1334
1335         cr1 = old_cr1 = readb(sport->port.membase + UARTCR1);
1336         old_cr2 = readb(sport->port.membase + UARTCR2);
1337         cr3 = readb(sport->port.membase + UARTCR3);
1338         cr4 = readb(sport->port.membase + UARTCR4);
1339         bdh = readb(sport->port.membase + UARTBDH);
1340         modem = readb(sport->port.membase + UARTMODEM);
1341         /*
1342          * only support CS8 and CS7, and for CS7 must enable PE.
1343          * supported mode:
1344          *  - (7,e/o,1)
1345          *  - (8,n,1)
1346          *  - (8,m/s,1)
1347          *  - (8,e/o,1)
1348          */
1349         while ((termios->c_cflag & CSIZE) != CS8 &&
1350                 (termios->c_cflag & CSIZE) != CS7) {
1351                 termios->c_cflag &= ~CSIZE;
1352                 termios->c_cflag |= old_csize;
1353                 old_csize = CS8;
1354         }
1355
1356         if ((termios->c_cflag & CSIZE) == CS8 ||
1357                 (termios->c_cflag & CSIZE) == CS7)
1358                 cr1 = old_cr1 & ~UARTCR1_M;
1359
1360         if (termios->c_cflag & CMSPAR) {
1361                 if ((termios->c_cflag & CSIZE) != CS8) {
1362                         termios->c_cflag &= ~CSIZE;
1363                         termios->c_cflag |= CS8;
1364                 }
1365                 cr1 |= UARTCR1_M;
1366         }
1367
1368         /*
1369          * When auto RS-485 RTS mode is enabled,
1370          * hardware flow control need to be disabled.
1371          */
1372         if (sport->port.rs485.flags & SER_RS485_ENABLED)
1373                 termios->c_cflag &= ~CRTSCTS;
1374
1375         if (termios->c_cflag & CRTSCTS) {
1376                 modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
1377         } else {
1378                 termios->c_cflag &= ~CRTSCTS;
1379                 modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
1380         }
1381
1382         if (termios->c_cflag & CSTOPB)
1383                 termios->c_cflag &= ~CSTOPB;
1384
1385         /* parity must be enabled when CS7 to match 8-bits format */
1386         if ((termios->c_cflag & CSIZE) == CS7)
1387                 termios->c_cflag |= PARENB;
1388
1389         if ((termios->c_cflag & PARENB)) {
1390                 if (termios->c_cflag & CMSPAR) {
1391                         cr1 &= ~UARTCR1_PE;
1392                         if (termios->c_cflag & PARODD)
1393                                 cr3 |= UARTCR3_T8;
1394                         else
1395                                 cr3 &= ~UARTCR3_T8;
1396                 } else {
1397                         cr1 |= UARTCR1_PE;
1398                         if ((termios->c_cflag & CSIZE) == CS8)
1399                                 cr1 |= UARTCR1_M;
1400                         if (termios->c_cflag & PARODD)
1401                                 cr1 |= UARTCR1_PT;
1402                         else
1403                                 cr1 &= ~UARTCR1_PT;
1404                 }
1405         }
1406
1407         /* ask the core to calculate the divisor */
1408         baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
1409
1410         spin_lock_irqsave(&sport->port.lock, flags);
1411
1412         sport->port.read_status_mask = 0;
1413         if (termios->c_iflag & INPCK)
1414                 sport->port.read_status_mask |= (UARTSR1_FE | UARTSR1_PE);
1415         if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
1416                 sport->port.read_status_mask |= UARTSR1_FE;
1417
1418         /* characters to ignore */
1419         sport->port.ignore_status_mask = 0;
1420         if (termios->c_iflag & IGNPAR)
1421                 sport->port.ignore_status_mask |= UARTSR1_PE;
1422         if (termios->c_iflag & IGNBRK) {
1423                 sport->port.ignore_status_mask |= UARTSR1_FE;
1424                 /*
1425                  * if we're ignoring parity and break indicators,
1426                  * ignore overruns too (for real raw support).
1427                  */
1428                 if (termios->c_iflag & IGNPAR)
1429                         sport->port.ignore_status_mask |= UARTSR1_OR;
1430         }
1431
1432         /* update the per-port timeout */
1433         uart_update_timeout(port, termios->c_cflag, baud);
1434
1435         /* wait transmit engin complete */
1436         while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
1437                 barrier();
1438
1439         /* disable transmit and receive */
1440         writeb(old_cr2 & ~(UARTCR2_TE | UARTCR2_RE),
1441                         sport->port.membase + UARTCR2);
1442
1443         sbr = sport->port.uartclk / (16 * baud);
1444         brfa = ((sport->port.uartclk - (16 * sbr * baud)) * 2) / baud;
1445         bdh &= ~UARTBDH_SBR_MASK;
1446         bdh |= (sbr >> 8) & 0x1F;
1447         cr4 &= ~UARTCR4_BRFA_MASK;
1448         brfa &= UARTCR4_BRFA_MASK;
1449         writeb(cr4 | brfa, sport->port.membase + UARTCR4);
1450         writeb(bdh, sport->port.membase + UARTBDH);
1451         writeb(sbr & 0xFF, sport->port.membase + UARTBDL);
1452         writeb(cr3, sport->port.membase + UARTCR3);
1453         writeb(cr1, sport->port.membase + UARTCR1);
1454         writeb(modem, sport->port.membase + UARTMODEM);
1455
1456         /* restore control register */
1457         writeb(old_cr2, sport->port.membase + UARTCR2);
1458
1459         /*
1460          * If new baud rate is set, we will also need to update the Ring buffer
1461          * length according to the selected baud rate and restart Rx DMA path.
1462          */
1463         if (old) {
1464                 if (sport->lpuart_dma_rx_use) {
1465                         del_timer_sync(&sport->lpuart_timer);
1466                         lpuart_dma_rx_free(&sport->port);
1467                 }
1468
1469                 if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
1470                         sport->lpuart_dma_rx_use = true;
1471                         rx_dma_timer_init(sport);
1472                 } else {
1473                         sport->lpuart_dma_rx_use = false;
1474                 }
1475         }
1476
1477         spin_unlock_irqrestore(&sport->port.lock, flags);
1478 }
1479
1480 static void
1481 lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
1482                    struct ktermios *old)
1483 {
1484         struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
1485         unsigned long flags;
1486         unsigned long ctrl, old_ctrl, bd, modem;
1487         unsigned int  baud;
1488         unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
1489         unsigned int sbr;
1490
1491         ctrl = old_ctrl = lpuart32_read(sport->port.membase + UARTCTRL);
1492         bd = lpuart32_read(sport->port.membase + UARTBAUD);
1493         modem = lpuart32_read(sport->port.membase + UARTMODIR);
1494         /*
1495          * only support CS8 and CS7, and for CS7 must enable PE.
1496          * supported mode:
1497          *  - (7,e/o,1)
1498          *  - (8,n,1)
1499          *  - (8,m/s,1)
1500          *  - (8,e/o,1)
1501          */
1502         while ((termios->c_cflag & CSIZE) != CS8 &&
1503                 (termios->c_cflag & CSIZE) != CS7) {
1504                 termios->c_cflag &= ~CSIZE;
1505                 termios->c_cflag |= old_csize;
1506                 old_csize = CS8;
1507         }
1508
1509         if ((termios->c_cflag & CSIZE) == CS8 ||
1510                 (termios->c_cflag & CSIZE) == CS7)
1511                 ctrl = old_ctrl & ~UARTCTRL_M;
1512
1513         if (termios->c_cflag & CMSPAR) {
1514                 if ((termios->c_cflag & CSIZE) != CS8) {
1515                         termios->c_cflag &= ~CSIZE;
1516                         termios->c_cflag |= CS8;
1517                 }
1518                 ctrl |= UARTCTRL_M;
1519         }
1520
1521         if (termios->c_cflag & CRTSCTS) {
1522                 modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
1523         } else {
1524                 termios->c_cflag &= ~CRTSCTS;
1525                 modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
1526         }
1527
1528         if (termios->c_cflag & CSTOPB)
1529                 termios->c_cflag &= ~CSTOPB;
1530
1531         /* parity must be enabled when CS7 to match 8-bits format */
1532         if ((termios->c_cflag & CSIZE) == CS7)
1533                 termios->c_cflag |= PARENB;
1534
1535         if ((termios->c_cflag & PARENB)) {
1536                 if (termios->c_cflag & CMSPAR) {
1537                         ctrl &= ~UARTCTRL_PE;
1538                         ctrl |= UARTCTRL_M;
1539                 } else {
1540                         ctrl |= UARTCR1_PE;
1541                         if ((termios->c_cflag & CSIZE) == CS8)
1542                                 ctrl |= UARTCTRL_M;
1543                         if (termios->c_cflag & PARODD)
1544                                 ctrl |= UARTCTRL_PT;
1545                         else
1546                                 ctrl &= ~UARTCTRL_PT;
1547                 }
1548         }
1549
1550         /* ask the core to calculate the divisor */
1551         baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
1552
1553         spin_lock_irqsave(&sport->port.lock, flags);
1554
1555         sport->port.read_status_mask = 0;
1556         if (termios->c_iflag & INPCK)
1557                 sport->port.read_status_mask |= (UARTSTAT_FE | UARTSTAT_PE);
1558         if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
1559                 sport->port.read_status_mask |= UARTSTAT_FE;
1560
1561         /* characters to ignore */
1562         sport->port.ignore_status_mask = 0;
1563         if (termios->c_iflag & IGNPAR)
1564                 sport->port.ignore_status_mask |= UARTSTAT_PE;
1565         if (termios->c_iflag & IGNBRK) {
1566                 sport->port.ignore_status_mask |= UARTSTAT_FE;
1567                 /*
1568                  * if we're ignoring parity and break indicators,
1569                  * ignore overruns too (for real raw support).
1570                  */
1571                 if (termios->c_iflag & IGNPAR)
1572                         sport->port.ignore_status_mask |= UARTSTAT_OR;
1573         }
1574
1575         /* update the per-port timeout */
1576         uart_update_timeout(port, termios->c_cflag, baud);
1577
1578         /* wait transmit engin complete */
1579         while (!(lpuart32_read(sport->port.membase + UARTSTAT) & UARTSTAT_TC))
1580                 barrier();
1581
1582         /* disable transmit and receive */
1583         lpuart32_write(old_ctrl & ~(UARTCTRL_TE | UARTCTRL_RE),
1584                         sport->port.membase + UARTCTRL);
1585
1586         sbr = sport->port.uartclk / (16 * baud);
1587         bd &= ~UARTBAUD_SBR_MASK;
1588         bd |= sbr & UARTBAUD_SBR_MASK;
1589         bd |= UARTBAUD_BOTHEDGE;
1590         bd &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
1591         lpuart32_write(bd, sport->port.membase + UARTBAUD);
1592         lpuart32_write(modem, sport->port.membase + UARTMODIR);
1593         lpuart32_write(ctrl, sport->port.membase + UARTCTRL);
1594         /* restore control register */
1595
1596         spin_unlock_irqrestore(&sport->port.lock, flags);
1597 }
1598
1599 static const char *lpuart_type(struct uart_port *port)
1600 {
1601         return "FSL_LPUART";
1602 }
1603
1604 static void lpuart_release_port(struct uart_port *port)
1605 {
1606         /* nothing to do */
1607 }
1608
1609 static int lpuart_request_port(struct uart_port *port)
1610 {
1611         return  0;
1612 }
1613
1614 /* configure/autoconfigure the port */
1615 static void lpuart_config_port(struct uart_port *port, int flags)
1616 {
1617         if (flags & UART_CONFIG_TYPE)
1618                 port->type = PORT_LPUART;
1619 }
1620
1621 static int lpuart_verify_port(struct uart_port *port, struct serial_struct *ser)
1622 {
1623         int ret = 0;
1624
1625         if (ser->type != PORT_UNKNOWN && ser->type != PORT_LPUART)
1626                 ret = -EINVAL;
1627         if (port->irq != ser->irq)
1628                 ret = -EINVAL;
1629         if (ser->io_type != UPIO_MEM)
1630                 ret = -EINVAL;
1631         if (port->uartclk / 16 != ser->baud_base)
1632                 ret = -EINVAL;
1633         if (port->iobase != ser->port)
1634                 ret = -EINVAL;
1635         if (ser->hub6 != 0)
1636                 ret = -EINVAL;
1637         return ret;
1638 }
1639
1640 static const struct uart_ops lpuart_pops = {
1641         .tx_empty       = lpuart_tx_empty,
1642         .set_mctrl      = lpuart_set_mctrl,
1643         .get_mctrl      = lpuart_get_mctrl,
1644         .stop_tx        = lpuart_stop_tx,
1645         .start_tx       = lpuart_start_tx,
1646         .stop_rx        = lpuart_stop_rx,
1647         .break_ctl      = lpuart_break_ctl,
1648         .startup        = lpuart_startup,
1649         .shutdown       = lpuart_shutdown,
1650         .set_termios    = lpuart_set_termios,
1651         .type           = lpuart_type,
1652         .request_port   = lpuart_request_port,
1653         .release_port   = lpuart_release_port,
1654         .config_port    = lpuart_config_port,
1655         .verify_port    = lpuart_verify_port,
1656         .flush_buffer   = lpuart_flush_buffer,
1657 #if defined(CONFIG_CONSOLE_POLL)
1658         .poll_init      = lpuart_poll_init,
1659         .poll_get_char  = lpuart_poll_get_char,
1660         .poll_put_char  = lpuart_poll_put_char,
1661 #endif
1662 };
1663
1664 static const struct uart_ops lpuart32_pops = {
1665         .tx_empty       = lpuart32_tx_empty,
1666         .set_mctrl      = lpuart32_set_mctrl,
1667         .get_mctrl      = lpuart32_get_mctrl,
1668         .stop_tx        = lpuart32_stop_tx,
1669         .start_tx       = lpuart32_start_tx,
1670         .stop_rx        = lpuart32_stop_rx,
1671         .break_ctl      = lpuart32_break_ctl,
1672         .startup        = lpuart32_startup,
1673         .shutdown       = lpuart32_shutdown,
1674         .set_termios    = lpuart32_set_termios,
1675         .type           = lpuart_type,
1676         .request_port   = lpuart_request_port,
1677         .release_port   = lpuart_release_port,
1678         .config_port    = lpuart_config_port,
1679         .verify_port    = lpuart_verify_port,
1680         .flush_buffer   = lpuart_flush_buffer,
1681 };
1682
1683 static struct lpuart_port *lpuart_ports[UART_NR];
1684
1685 #ifdef CONFIG_SERIAL_FSL_LPUART_CONSOLE
1686 static void lpuart_console_putchar(struct uart_port *port, int ch)
1687 {
1688         while (!(readb(port->membase + UARTSR1) & UARTSR1_TDRE))
1689                 barrier();
1690
1691         writeb(ch, port->membase + UARTDR);
1692 }
1693
1694 static void lpuart32_console_putchar(struct uart_port *port, int ch)
1695 {
1696         while (!(lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TDRE))
1697                 barrier();
1698
1699         lpuart32_write(ch, port->membase + UARTDATA);
1700 }
1701
1702 static void
1703 lpuart_console_write(struct console *co, const char *s, unsigned int count)
1704 {
1705         struct lpuart_port *sport = lpuart_ports[co->index];
1706         unsigned char  old_cr2, cr2;
1707
1708         /* first save CR2 and then disable interrupts */
1709         cr2 = old_cr2 = readb(sport->port.membase + UARTCR2);
1710         cr2 |= (UARTCR2_TE |  UARTCR2_RE);
1711         cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
1712         writeb(cr2, sport->port.membase + UARTCR2);
1713
1714         uart_console_write(&sport->port, s, count, lpuart_console_putchar);
1715
1716         /* wait for transmitter finish complete and restore CR2 */
1717         while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
1718                 barrier();
1719
1720         writeb(old_cr2, sport->port.membase + UARTCR2);
1721 }
1722
1723 static void
1724 lpuart32_console_write(struct console *co, const char *s, unsigned int count)
1725 {
1726         struct lpuart_port *sport = lpuart_ports[co->index];
1727         unsigned long  old_cr, cr;
1728
1729         /* first save CR2 and then disable interrupts */
1730         cr = old_cr = lpuart32_read(sport->port.membase + UARTCTRL);
1731         cr |= (UARTCTRL_TE |  UARTCTRL_RE);
1732         cr &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE);
1733         lpuart32_write(cr, sport->port.membase + UARTCTRL);
1734
1735         uart_console_write(&sport->port, s, count, lpuart32_console_putchar);
1736
1737         /* wait for transmitter finish complete and restore CR2 */
1738         while (!(lpuart32_read(sport->port.membase + UARTSTAT) & UARTSTAT_TC))
1739                 barrier();
1740
1741         lpuart32_write(old_cr, sport->port.membase + UARTCTRL);
1742 }
1743
1744 /*
1745  * if the port was already initialised (eg, by a boot loader),
1746  * try to determine the current setup.
1747  */
1748 static void __init
1749 lpuart_console_get_options(struct lpuart_port *sport, int *baud,
1750                            int *parity, int *bits)
1751 {
1752         unsigned char cr, bdh, bdl, brfa;
1753         unsigned int sbr, uartclk, baud_raw;
1754
1755         cr = readb(sport->port.membase + UARTCR2);
1756         cr &= UARTCR2_TE | UARTCR2_RE;
1757         if (!cr)
1758                 return;
1759
1760         /* ok, the port was enabled */
1761
1762         cr = readb(sport->port.membase + UARTCR1);
1763
1764         *parity = 'n';
1765         if (cr & UARTCR1_PE) {
1766                 if (cr & UARTCR1_PT)
1767                         *parity = 'o';
1768                 else
1769                         *parity = 'e';
1770         }
1771
1772         if (cr & UARTCR1_M)
1773                 *bits = 9;
1774         else
1775                 *bits = 8;
1776
1777         bdh = readb(sport->port.membase + UARTBDH);
1778         bdh &= UARTBDH_SBR_MASK;
1779         bdl = readb(sport->port.membase + UARTBDL);
1780         sbr = bdh;
1781         sbr <<= 8;
1782         sbr |= bdl;
1783         brfa = readb(sport->port.membase + UARTCR4);
1784         brfa &= UARTCR4_BRFA_MASK;
1785
1786         uartclk = clk_get_rate(sport->clk);
1787         /*
1788          * baud = mod_clk/(16*(sbr[13]+(brfa)/32)
1789          */
1790         baud_raw = uartclk / (16 * (sbr + brfa / 32));
1791
1792         if (*baud != baud_raw)
1793                 printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
1794                                 "from %d to %d\n", baud_raw, *baud);
1795 }
1796
1797 static void __init
1798 lpuart32_console_get_options(struct lpuart_port *sport, int *baud,
1799                            int *parity, int *bits)
1800 {
1801         unsigned long cr, bd;
1802         unsigned int sbr, uartclk, baud_raw;
1803
1804         cr = lpuart32_read(sport->port.membase + UARTCTRL);
1805         cr &= UARTCTRL_TE | UARTCTRL_RE;
1806         if (!cr)
1807                 return;
1808
1809         /* ok, the port was enabled */
1810
1811         cr = lpuart32_read(sport->port.membase + UARTCTRL);
1812
1813         *parity = 'n';
1814         if (cr & UARTCTRL_PE) {
1815                 if (cr & UARTCTRL_PT)
1816                         *parity = 'o';
1817                 else
1818                         *parity = 'e';
1819         }
1820
1821         if (cr & UARTCTRL_M)
1822                 *bits = 9;
1823         else
1824                 *bits = 8;
1825
1826         bd = lpuart32_read(sport->port.membase + UARTBAUD);
1827         bd &= UARTBAUD_SBR_MASK;
1828         sbr = bd;
1829         uartclk = clk_get_rate(sport->clk);
1830         /*
1831          * baud = mod_clk/(16*(sbr[13]+(brfa)/32)
1832          */
1833         baud_raw = uartclk / (16 * sbr);
1834
1835         if (*baud != baud_raw)
1836                 printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
1837                                 "from %d to %d\n", baud_raw, *baud);
1838 }
1839
1840 static int __init lpuart_console_setup(struct console *co, char *options)
1841 {
1842         struct lpuart_port *sport;
1843         int baud = 115200;
1844         int bits = 8;
1845         int parity = 'n';
1846         int flow = 'n';
1847
1848         /*
1849          * check whether an invalid uart number has been specified, and
1850          * if so, search for the first available port that does have
1851          * console support.
1852          */
1853         if (co->index == -1 || co->index >= ARRAY_SIZE(lpuart_ports))
1854                 co->index = 0;
1855
1856         sport = lpuart_ports[co->index];
1857         if (sport == NULL)
1858                 return -ENODEV;
1859
1860         if (options)
1861                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1862         else
1863                 if (sport->lpuart32)
1864                         lpuart32_console_get_options(sport, &baud, &parity, &bits);
1865                 else
1866                         lpuart_console_get_options(sport, &baud, &parity, &bits);
1867
1868         if (sport->lpuart32)
1869                 lpuart32_setup_watermark(sport);
1870         else
1871                 lpuart_setup_watermark(sport);
1872
1873         return uart_set_options(&sport->port, co, baud, parity, bits, flow);
1874 }
1875
1876 static struct uart_driver lpuart_reg;
1877 static struct console lpuart_console = {
1878         .name           = DEV_NAME,
1879         .write          = lpuart_console_write,
1880         .device         = uart_console_device,
1881         .setup          = lpuart_console_setup,
1882         .flags          = CON_PRINTBUFFER,
1883         .index          = -1,
1884         .data           = &lpuart_reg,
1885 };
1886
1887 static struct console lpuart32_console = {
1888         .name           = DEV_NAME,
1889         .write          = lpuart32_console_write,
1890         .device         = uart_console_device,
1891         .setup          = lpuart_console_setup,
1892         .flags          = CON_PRINTBUFFER,
1893         .index          = -1,
1894         .data           = &lpuart_reg,
1895 };
1896
1897 static void lpuart_early_write(struct console *con, const char *s, unsigned n)
1898 {
1899         struct earlycon_device *dev = con->data;
1900
1901         uart_console_write(&dev->port, s, n, lpuart_console_putchar);
1902 }
1903
1904 static void lpuart32_early_write(struct console *con, const char *s, unsigned n)
1905 {
1906         struct earlycon_device *dev = con->data;
1907
1908         uart_console_write(&dev->port, s, n, lpuart32_console_putchar);
1909 }
1910
1911 static int __init lpuart_early_console_setup(struct earlycon_device *device,
1912                                           const char *opt)
1913 {
1914         if (!device->port.membase)
1915                 return -ENODEV;
1916
1917         device->con->write = lpuart_early_write;
1918         return 0;
1919 }
1920
1921 static int __init lpuart32_early_console_setup(struct earlycon_device *device,
1922                                           const char *opt)
1923 {
1924         if (!device->port.membase)
1925                 return -ENODEV;
1926
1927         device->con->write = lpuart32_early_write;
1928         return 0;
1929 }
1930
1931 OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
1932 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
1933 EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
1934 EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
1935
1936 #define LPUART_CONSOLE  (&lpuart_console)
1937 #define LPUART32_CONSOLE        (&lpuart32_console)
1938 #else
1939 #define LPUART_CONSOLE  NULL
1940 #define LPUART32_CONSOLE        NULL
1941 #endif
1942
1943 static struct uart_driver lpuart_reg = {
1944         .owner          = THIS_MODULE,
1945         .driver_name    = DRIVER_NAME,
1946         .dev_name       = DEV_NAME,
1947         .nr             = ARRAY_SIZE(lpuart_ports),
1948         .cons           = LPUART_CONSOLE,
1949 };
1950
1951 static int lpuart_probe(struct platform_device *pdev)
1952 {
1953         struct device_node *np = pdev->dev.of_node;
1954         struct lpuart_port *sport;
1955         struct resource *res;
1956         int ret;
1957
1958         sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
1959         if (!sport)
1960                 return -ENOMEM;
1961
1962         pdev->dev.coherent_dma_mask = 0;
1963
1964         ret = of_alias_get_id(np, "serial");
1965         if (ret < 0) {
1966                 dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
1967                 return ret;
1968         }
1969         sport->port.line = ret;
1970         sport->lpuart32 = of_device_is_compatible(np, "fsl,ls1021a-lpuart");
1971
1972         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1973         sport->port.membase = devm_ioremap_resource(&pdev->dev, res);
1974         if (IS_ERR(sport->port.membase))
1975                 return PTR_ERR(sport->port.membase);
1976
1977         sport->port.mapbase = res->start;
1978         sport->port.dev = &pdev->dev;
1979         sport->port.type = PORT_LPUART;
1980         sport->port.iotype = UPIO_MEM;
1981         ret = platform_get_irq(pdev, 0);
1982         if (ret < 0) {
1983                 dev_err(&pdev->dev, "cannot obtain irq\n");
1984                 return ret;
1985         }
1986         sport->port.irq = ret;
1987
1988         if (sport->lpuart32)
1989                 sport->port.ops = &lpuart32_pops;
1990         else
1991                 sport->port.ops = &lpuart_pops;
1992         sport->port.flags = UPF_BOOT_AUTOCONF;
1993
1994         sport->port.rs485_config = lpuart_config_rs485;
1995
1996         sport->clk = devm_clk_get(&pdev->dev, "ipg");
1997         if (IS_ERR(sport->clk)) {
1998                 ret = PTR_ERR(sport->clk);
1999                 dev_err(&pdev->dev, "failed to get uart clk: %d\n", ret);
2000                 return ret;
2001         }
2002
2003         ret = clk_prepare_enable(sport->clk);
2004         if (ret) {
2005                 dev_err(&pdev->dev, "failed to enable uart clk: %d\n", ret);
2006                 return ret;
2007         }
2008
2009         sport->port.uartclk = clk_get_rate(sport->clk);
2010
2011         lpuart_ports[sport->port.line] = sport;
2012
2013         platform_set_drvdata(pdev, &sport->port);
2014
2015         if (sport->lpuart32)
2016                 lpuart_reg.cons = LPUART32_CONSOLE;
2017         else
2018                 lpuart_reg.cons = LPUART_CONSOLE;
2019
2020         ret = uart_add_one_port(&lpuart_reg, &sport->port);
2021         if (ret) {
2022                 clk_disable_unprepare(sport->clk);
2023                 return ret;
2024         }
2025
2026         sport->dma_tx_chan = dma_request_slave_channel(sport->port.dev, "tx");
2027         if (!sport->dma_tx_chan)
2028                 dev_info(sport->port.dev, "DMA tx channel request failed, "
2029                                 "operating without tx DMA\n");
2030
2031         sport->dma_rx_chan = dma_request_slave_channel(sport->port.dev, "rx");
2032         if (!sport->dma_rx_chan)
2033                 dev_info(sport->port.dev, "DMA rx channel request failed, "
2034                                 "operating without rx DMA\n");
2035
2036         if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time")) {
2037                 sport->port.rs485.flags |= SER_RS485_ENABLED;
2038                 sport->port.rs485.flags |= SER_RS485_RTS_ON_SEND;
2039                 writeb(UARTMODEM_TXRTSE, sport->port.membase + UARTMODEM);
2040         }
2041
2042         return 0;
2043 }
2044
2045 static int lpuart_remove(struct platform_device *pdev)
2046 {
2047         struct lpuart_port *sport = platform_get_drvdata(pdev);
2048
2049         uart_remove_one_port(&lpuart_reg, &sport->port);
2050
2051         clk_disable_unprepare(sport->clk);
2052
2053         if (sport->dma_tx_chan)
2054                 dma_release_channel(sport->dma_tx_chan);
2055
2056         if (sport->dma_rx_chan)
2057                 dma_release_channel(sport->dma_rx_chan);
2058
2059         return 0;
2060 }
2061
2062 #ifdef CONFIG_PM_SLEEP
2063 static int lpuart_suspend(struct device *dev)
2064 {
2065         struct lpuart_port *sport = dev_get_drvdata(dev);
2066         unsigned long temp;
2067
2068         if (sport->lpuart32) {
2069                 /* disable Rx/Tx and interrupts */
2070                 temp = lpuart32_read(sport->port.membase + UARTCTRL);
2071                 temp &= ~(UARTCTRL_TE | UARTCTRL_TIE | UARTCTRL_TCIE);
2072                 lpuart32_write(temp, sport->port.membase + UARTCTRL);
2073         } else {
2074                 /* disable Rx/Tx and interrupts */
2075                 temp = readb(sport->port.membase + UARTCR2);
2076                 temp &= ~(UARTCR2_TE | UARTCR2_TIE | UARTCR2_TCIE);
2077                 writeb(temp, sport->port.membase + UARTCR2);
2078         }
2079
2080         uart_suspend_port(&lpuart_reg, &sport->port);
2081
2082         if (sport->lpuart_dma_rx_use) {
2083                 /*
2084                  * EDMA driver during suspend will forcefully release any
2085                  * non-idle DMA channels. If port wakeup is enabled or if port
2086                  * is console port or 'no_console_suspend' is set the Rx DMA
2087                  * cannot resume as as expected, hence gracefully release the
2088                  * Rx DMA path before suspend and start Rx DMA path on resume.
2089                  */
2090                 if (sport->port.irq_wake) {
2091                         del_timer_sync(&sport->lpuart_timer);
2092                         lpuart_dma_rx_free(&sport->port);
2093                 }
2094
2095                 /* Disable Rx DMA to use UART port as wakeup source */
2096                 writeb(readb(sport->port.membase + UARTCR5) & ~UARTCR5_RDMAS,
2097                                         sport->port.membase + UARTCR5);
2098         }
2099
2100         if (sport->lpuart_dma_tx_use) {
2101                 sport->dma_tx_in_progress = false;
2102                 dmaengine_terminate_all(sport->dma_tx_chan);
2103         }
2104
2105         if (sport->port.suspended && !sport->port.irq_wake)
2106                 clk_disable_unprepare(sport->clk);
2107
2108         return 0;
2109 }
2110
2111 static int lpuart_resume(struct device *dev)
2112 {
2113         struct lpuart_port *sport = dev_get_drvdata(dev);
2114         unsigned long temp;
2115
2116         if (sport->port.suspended && !sport->port.irq_wake)
2117                 clk_prepare_enable(sport->clk);
2118
2119         if (sport->lpuart32) {
2120                 lpuart32_setup_watermark(sport);
2121                 temp = lpuart32_read(sport->port.membase + UARTCTRL);
2122                 temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE |
2123                          UARTCTRL_TE | UARTCTRL_ILIE);
2124                 lpuart32_write(temp, sport->port.membase + UARTCTRL);
2125         } else {
2126                 lpuart_setup_watermark(sport);
2127                 temp = readb(sport->port.membase + UARTCR2);
2128                 temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
2129                 writeb(temp, sport->port.membase + UARTCR2);
2130         }
2131
2132         if (sport->lpuart_dma_rx_use) {
2133                 if (sport->port.irq_wake) {
2134                         if (!lpuart_start_rx_dma(sport)) {
2135                                 sport->lpuart_dma_rx_use = true;
2136                                 rx_dma_timer_init(sport);
2137                         } else {
2138                                 sport->lpuart_dma_rx_use = false;
2139                         }
2140                 }
2141         }
2142
2143         if (sport->dma_tx_chan && !lpuart_dma_tx_request(&sport->port)) {
2144                         init_waitqueue_head(&sport->dma_wait);
2145                         sport->lpuart_dma_tx_use = true;
2146                         writeb(readb(sport->port.membase + UARTCR5) |
2147                                 UARTCR5_TDMAS, sport->port.membase + UARTCR5);
2148         } else {
2149                 sport->lpuart_dma_tx_use = false;
2150         }
2151
2152         uart_resume_port(&lpuart_reg, &sport->port);
2153
2154         return 0;
2155 }
2156 #endif
2157
2158 static SIMPLE_DEV_PM_OPS(lpuart_pm_ops, lpuart_suspend, lpuart_resume);
2159
2160 static struct platform_driver lpuart_driver = {
2161         .probe          = lpuart_probe,
2162         .remove         = lpuart_remove,
2163         .driver         = {
2164                 .name   = "fsl-lpuart",
2165                 .of_match_table = lpuart_dt_ids,
2166                 .pm     = &lpuart_pm_ops,
2167         },
2168 };
2169
2170 static int __init lpuart_serial_init(void)
2171 {
2172         int ret = uart_register_driver(&lpuart_reg);
2173
2174         if (ret)
2175                 return ret;
2176
2177         ret = platform_driver_register(&lpuart_driver);
2178         if (ret)
2179                 uart_unregister_driver(&lpuart_reg);
2180
2181         return ret;
2182 }
2183
2184 static void __exit lpuart_serial_exit(void)
2185 {
2186         platform_driver_unregister(&lpuart_driver);
2187         uart_unregister_driver(&lpuart_reg);
2188 }
2189
2190 module_init(lpuart_serial_init);
2191 module_exit(lpuart_serial_exit);
2192
2193 MODULE_DESCRIPTION("Freescale lpuart serial port driver");
2194 MODULE_LICENSE("GPL v2");