2 * MUSB OTG driver core code
4 * Copyright 2005 Mentor Graphics Corporation
5 * Copyright (C) 2005-2006 by Texas Instruments
6 * Copyright (C) 2006-2007 Nokia Corporation
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * version 2 as published by the Free Software Foundation.
12 * This program is distributed in the hope that it will be useful, but
13 * WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
15 * General Public License for more details.
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
22 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
23 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
24 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
25 * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT,
26 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
27 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
28 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
29 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
30 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
31 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
36 * Inventra (Multipoint) Dual-Role Controller Driver for Linux.
38 * This consists of a Host Controller Driver (HCD) and a peripheral
39 * controller driver implementing the "Gadget" API; OTG support is
40 * in the works. These are normal Linux-USB controller drivers which
41 * use IRQs and have no dedicated thread.
43 * This version of the driver has only been used with products from
44 * Texas Instruments. Those products integrate the Inventra logic
45 * with other DMA, IRQ, and bus modules, as well as other logic that
46 * needs to be reflected in this driver.
49 * NOTE: the original Mentor code here was pretty much a collection
50 * of mechanisms that don't seem to have been fully integrated/working
51 * for *any* Linux kernel version. This version aims at Linux 2.6.now,
52 * Key open issues include:
54 * - Lack of host-side transaction scheduling, for all transfer types.
55 * The hardware doesn't do it; instead, software must.
57 * This is not an issue for OTG devices that don't support external
58 * hubs, but for more "normal" USB hosts it's a user issue that the
59 * "multipoint" support doesn't scale in the expected ways. That
60 * includes DaVinci EVM in a common non-OTG mode.
62 * * Control and bulk use dedicated endpoints, and there's as
63 * yet no mechanism to either (a) reclaim the hardware when
64 * peripherals are NAKing, which gets complicated with bulk
65 * endpoints, or (b) use more than a single bulk endpoint in
68 * RESULT: one device may be perceived as blocking another one.
70 * * Interrupt and isochronous will dynamically allocate endpoint
71 * hardware, but (a) there's no record keeping for bandwidth;
72 * (b) in the common case that few endpoints are available, there
73 * is no mechanism to reuse endpoints to talk to multiple devices.
75 * RESULT: At one extreme, bandwidth can be overcommitted in
76 * some hardware configurations, no faults will be reported.
77 * At the other extreme, the bandwidth capabilities which do
78 * exist tend to be severely undercommitted. You can't yet hook
79 * up both a keyboard and a mouse to an external USB hub.
83 * This gets many kinds of configuration information:
84 * - Kconfig for everything user-configurable
85 * - platform_device for addressing, irq, and platform_data
86 * - platform_data is mostly for board-specific information
87 * (plus recentrly, SOC or family details)
89 * Most of the conditional compilation will (someday) vanish.
92 #include <linux/module.h>
93 #include <linux/kernel.h>
94 #include <linux/sched.h>
95 #include <linux/slab.h>
96 #include <linux/list.h>
97 #include <linux/kobject.h>
98 #include <linux/prefetch.h>
99 #include <linux/platform_device.h>
100 #include <linux/io.h>
101 #include <linux/dma-mapping.h>
102 #include <linux/usb.h>
104 #include "musb_core.h"
105 #include "musb_trace.h"
107 #define TA_WAIT_BCON(m) max_t(int, (m)->a_wait_bcon, OTG_TIME_A_WAIT_BCON)
110 #define DRIVER_AUTHOR "Mentor Graphics, Texas Instruments, Nokia"
111 #define DRIVER_DESC "Inventra Dual-Role USB Controller Driver"
113 #define MUSB_VERSION "6.0"
115 #define DRIVER_INFO DRIVER_DESC ", v" MUSB_VERSION
117 #define MUSB_DRIVER_NAME "musb-hdrc"
118 const char musb_driver_name[] = MUSB_DRIVER_NAME;
120 MODULE_DESCRIPTION(DRIVER_INFO);
121 MODULE_AUTHOR(DRIVER_AUTHOR);
122 MODULE_LICENSE("GPL");
123 MODULE_ALIAS("platform:" MUSB_DRIVER_NAME);
126 /*-------------------------------------------------------------------------*/
128 static inline struct musb *dev_to_musb(struct device *dev)
130 return dev_get_drvdata(dev);
133 /*-------------------------------------------------------------------------*/
135 #ifndef CONFIG_BLACKFIN
136 static int musb_ulpi_read(struct usb_phy *phy, u32 reg)
138 void __iomem *addr = phy->io_priv;
144 pm_runtime_get_sync(phy->io_dev);
146 /* Make sure the transceiver is not in low power mode */
147 power = musb_readb(addr, MUSB_POWER);
148 power &= ~MUSB_POWER_SUSPENDM;
149 musb_writeb(addr, MUSB_POWER, power);
151 /* REVISIT: musbhdrc_ulpi_an.pdf recommends setting the
152 * ULPICarKitControlDisableUTMI after clearing POWER_SUSPENDM.
155 musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)reg);
156 musb_writeb(addr, MUSB_ULPI_REG_CONTROL,
157 MUSB_ULPI_REG_REQ | MUSB_ULPI_RDN_WR);
159 while (!(musb_readb(addr, MUSB_ULPI_REG_CONTROL)
160 & MUSB_ULPI_REG_CMPLT)) {
168 r = musb_readb(addr, MUSB_ULPI_REG_CONTROL);
169 r &= ~MUSB_ULPI_REG_CMPLT;
170 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, r);
172 ret = musb_readb(addr, MUSB_ULPI_REG_DATA);
175 pm_runtime_put(phy->io_dev);
180 static int musb_ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
182 void __iomem *addr = phy->io_priv;
188 pm_runtime_get_sync(phy->io_dev);
190 /* Make sure the transceiver is not in low power mode */
191 power = musb_readb(addr, MUSB_POWER);
192 power &= ~MUSB_POWER_SUSPENDM;
193 musb_writeb(addr, MUSB_POWER, power);
195 musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)reg);
196 musb_writeb(addr, MUSB_ULPI_REG_DATA, (u8)val);
197 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, MUSB_ULPI_REG_REQ);
199 while (!(musb_readb(addr, MUSB_ULPI_REG_CONTROL)
200 & MUSB_ULPI_REG_CMPLT)) {
208 r = musb_readb(addr, MUSB_ULPI_REG_CONTROL);
209 r &= ~MUSB_ULPI_REG_CMPLT;
210 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, r);
213 pm_runtime_put(phy->io_dev);
218 #define musb_ulpi_read NULL
219 #define musb_ulpi_write NULL
222 static struct usb_phy_io_ops musb_ulpi_access = {
223 .read = musb_ulpi_read,
224 .write = musb_ulpi_write,
227 /*-------------------------------------------------------------------------*/
229 static u32 musb_default_fifo_offset(u8 epnum)
231 return 0x20 + (epnum * 4);
234 /* "flat" mapping: each endpoint has its own i/o address */
235 static void musb_flat_ep_select(void __iomem *mbase, u8 epnum)
239 static u32 musb_flat_ep_offset(u8 epnum, u16 offset)
241 return 0x100 + (0x10 * epnum) + offset;
244 /* "indexed" mapping: INDEX register controls register bank select */
245 static void musb_indexed_ep_select(void __iomem *mbase, u8 epnum)
247 musb_writeb(mbase, MUSB_INDEX, epnum);
250 static u32 musb_indexed_ep_offset(u8 epnum, u16 offset)
252 return 0x10 + offset;
255 static u32 musb_default_busctl_offset(u8 epnum, u16 offset)
257 return 0x80 + (0x08 * epnum) + offset;
260 static u8 musb_default_readb(const void __iomem *addr, unsigned offset)
262 u8 data = __raw_readb(addr + offset);
264 trace_musb_readb(__builtin_return_address(0), addr, offset, data);
268 static void musb_default_writeb(void __iomem *addr, unsigned offset, u8 data)
270 trace_musb_writeb(__builtin_return_address(0), addr, offset, data);
271 __raw_writeb(data, addr + offset);
274 static u16 musb_default_readw(const void __iomem *addr, unsigned offset)
276 u16 data = __raw_readw(addr + offset);
278 trace_musb_readw(__builtin_return_address(0), addr, offset, data);
282 static void musb_default_writew(void __iomem *addr, unsigned offset, u16 data)
284 trace_musb_writew(__builtin_return_address(0), addr, offset, data);
285 __raw_writew(data, addr + offset);
288 static u32 musb_default_readl(const void __iomem *addr, unsigned offset)
290 u32 data = __raw_readl(addr + offset);
292 trace_musb_readl(__builtin_return_address(0), addr, offset, data);
296 static void musb_default_writel(void __iomem *addr, unsigned offset, u32 data)
298 trace_musb_writel(__builtin_return_address(0), addr, offset, data);
299 __raw_writel(data, addr + offset);
303 * Load an endpoint's FIFO
305 static void musb_default_write_fifo(struct musb_hw_ep *hw_ep, u16 len,
308 struct musb *musb = hw_ep->musb;
309 void __iomem *fifo = hw_ep->fifo;
311 if (unlikely(len == 0))
316 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
317 'T', hw_ep->epnum, fifo, len, src);
319 /* we can't assume unaligned reads work */
320 if (likely((0x01 & (unsigned long) src) == 0)) {
323 /* best case is 32bit-aligned source address */
324 if ((0x02 & (unsigned long) src) == 0) {
326 iowrite32_rep(fifo, src + index, len >> 2);
327 index += len & ~0x03;
330 __raw_writew(*(u16 *)&src[index], fifo);
335 iowrite16_rep(fifo, src + index, len >> 1);
336 index += len & ~0x01;
340 __raw_writeb(src[index], fifo);
343 iowrite8_rep(fifo, src, len);
348 * Unload an endpoint's FIFO
350 static void musb_default_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
352 struct musb *musb = hw_ep->musb;
353 void __iomem *fifo = hw_ep->fifo;
355 if (unlikely(len == 0))
358 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
359 'R', hw_ep->epnum, fifo, len, dst);
361 /* we can't assume unaligned writes work */
362 if (likely((0x01 & (unsigned long) dst) == 0)) {
365 /* best case is 32bit-aligned destination address */
366 if ((0x02 & (unsigned long) dst) == 0) {
368 ioread32_rep(fifo, dst, len >> 2);
372 *(u16 *)&dst[index] = __raw_readw(fifo);
377 ioread16_rep(fifo, dst, len >> 1);
382 dst[index] = __raw_readb(fifo);
385 ioread8_rep(fifo, dst, len);
390 * Old style IO functions
392 u8 (*musb_readb)(const void __iomem *addr, unsigned offset);
393 EXPORT_SYMBOL_GPL(musb_readb);
395 void (*musb_writeb)(void __iomem *addr, unsigned offset, u8 data);
396 EXPORT_SYMBOL_GPL(musb_writeb);
398 u16 (*musb_readw)(const void __iomem *addr, unsigned offset);
399 EXPORT_SYMBOL_GPL(musb_readw);
401 void (*musb_writew)(void __iomem *addr, unsigned offset, u16 data);
402 EXPORT_SYMBOL_GPL(musb_writew);
404 u32 (*musb_readl)(const void __iomem *addr, unsigned offset);
405 EXPORT_SYMBOL_GPL(musb_readl);
407 void (*musb_writel)(void __iomem *addr, unsigned offset, u32 data);
408 EXPORT_SYMBOL_GPL(musb_writel);
410 #ifndef CONFIG_MUSB_PIO_ONLY
411 struct dma_controller *
412 (*musb_dma_controller_create)(struct musb *musb, void __iomem *base);
413 EXPORT_SYMBOL(musb_dma_controller_create);
415 void (*musb_dma_controller_destroy)(struct dma_controller *c);
416 EXPORT_SYMBOL(musb_dma_controller_destroy);
420 * New style IO functions
422 void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
424 return hw_ep->musb->io.read_fifo(hw_ep, len, dst);
427 void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
429 return hw_ep->musb->io.write_fifo(hw_ep, len, src);
432 /*-------------------------------------------------------------------------*/
434 /* for high speed test mode; see USB 2.0 spec 7.1.20 */
435 static const u8 musb_test_packet[53] = {
436 /* implicit SYNC then DATA0 to start */
439 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
441 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa,
443 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee,
444 /* JJJJJJJKKKKKKK x8 */
445 0xfe, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
447 0x7f, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd,
448 /* JKKKKKKK x10, JK */
449 0xfc, 0x7e, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, 0x7e
451 /* implicit CRC16 then EOP to end */
454 void musb_load_testpacket(struct musb *musb)
456 void __iomem *regs = musb->endpoints[0].regs;
458 musb_ep_select(musb->mregs, 0);
459 musb_write_fifo(musb->control_ep,
460 sizeof(musb_test_packet), musb_test_packet);
461 musb_writew(regs, MUSB_CSR0, MUSB_CSR0_TXPKTRDY);
464 /*-------------------------------------------------------------------------*/
467 * Handles OTG hnp timeouts, such as b_ase0_brst
469 static void musb_otg_timer_func(unsigned long data)
471 struct musb *musb = (struct musb *)data;
474 spin_lock_irqsave(&musb->lock, flags);
475 switch (musb->xceiv->otg->state) {
476 case OTG_STATE_B_WAIT_ACON:
478 "HNP: b_wait_acon timeout; back to b_peripheral");
479 musb_g_disconnect(musb);
480 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
483 case OTG_STATE_A_SUSPEND:
484 case OTG_STATE_A_WAIT_BCON:
485 musb_dbg(musb, "HNP: %s timeout",
486 usb_otg_state_string(musb->xceiv->otg->state));
487 musb_platform_set_vbus(musb, 0);
488 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
491 musb_dbg(musb, "HNP: Unhandled mode %s",
492 usb_otg_state_string(musb->xceiv->otg->state));
494 spin_unlock_irqrestore(&musb->lock, flags);
498 * Stops the HNP transition. Caller must take care of locking.
500 void musb_hnp_stop(struct musb *musb)
502 struct usb_hcd *hcd = musb->hcd;
503 void __iomem *mbase = musb->mregs;
506 musb_dbg(musb, "HNP: stop from %s",
507 usb_otg_state_string(musb->xceiv->otg->state));
509 switch (musb->xceiv->otg->state) {
510 case OTG_STATE_A_PERIPHERAL:
511 musb_g_disconnect(musb);
512 musb_dbg(musb, "HNP: back to %s",
513 usb_otg_state_string(musb->xceiv->otg->state));
515 case OTG_STATE_B_HOST:
516 musb_dbg(musb, "HNP: Disabling HR");
518 hcd->self.is_b_host = 0;
519 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
521 reg = musb_readb(mbase, MUSB_POWER);
522 reg |= MUSB_POWER_SUSPENDM;
523 musb_writeb(mbase, MUSB_POWER, reg);
524 /* REVISIT: Start SESSION_REQUEST here? */
527 musb_dbg(musb, "HNP: Stopping in unknown state %s",
528 usb_otg_state_string(musb->xceiv->otg->state));
532 * When returning to A state after HNP, avoid hub_port_rebounce(),
533 * which cause occasional OPT A "Did not receive reset after connect"
536 musb->port1_status &= ~(USB_PORT_STAT_C_CONNECTION << 16);
539 static void musb_recover_from_babble(struct musb *musb);
542 * Interrupt Service Routine to record USB "global" interrupts.
543 * Since these do not happen often and signify things of
544 * paramount importance, it seems OK to check them individually;
545 * the order of the tests is specified in the manual
547 * @param musb instance pointer
548 * @param int_usb register contents
553 static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb,
556 irqreturn_t handled = IRQ_NONE;
558 musb_dbg(musb, "<== DevCtl=%02x, int_usb=0x%x", devctl, int_usb);
560 /* in host mode, the peripheral may issue remote wakeup.
561 * in peripheral mode, the host may resume the link.
562 * spurious RESUME irqs happen too, paired with SUSPEND.
564 if (int_usb & MUSB_INTR_RESUME) {
565 handled = IRQ_HANDLED;
566 musb_dbg(musb, "RESUME (%s)",
567 usb_otg_state_string(musb->xceiv->otg->state));
569 if (devctl & MUSB_DEVCTL_HM) {
570 switch (musb->xceiv->otg->state) {
571 case OTG_STATE_A_SUSPEND:
572 /* remote wakeup? later, GetPortStatus
573 * will stop RESUME signaling
576 musb->port1_status |=
577 (USB_PORT_STAT_C_SUSPEND << 16)
578 | MUSB_PORT_STAT_RESUME;
579 musb->rh_timer = jiffies
580 + msecs_to_jiffies(USB_RESUME_TIMEOUT);
581 musb->need_finish_resume = 1;
583 musb->xceiv->otg->state = OTG_STATE_A_HOST;
585 musb_host_resume_root_hub(musb);
587 case OTG_STATE_B_WAIT_ACON:
588 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
593 WARNING("bogus %s RESUME (%s)\n",
595 usb_otg_state_string(musb->xceiv->otg->state));
598 switch (musb->xceiv->otg->state) {
599 case OTG_STATE_A_SUSPEND:
600 /* possibly DISCONNECT is upcoming */
601 musb->xceiv->otg->state = OTG_STATE_A_HOST;
602 musb_host_resume_root_hub(musb);
604 case OTG_STATE_B_WAIT_ACON:
605 case OTG_STATE_B_PERIPHERAL:
606 /* disconnect while suspended? we may
607 * not get a disconnect irq...
609 if ((devctl & MUSB_DEVCTL_VBUS)
610 != (3 << MUSB_DEVCTL_VBUS_SHIFT)
612 musb->int_usb |= MUSB_INTR_DISCONNECT;
613 musb->int_usb &= ~MUSB_INTR_SUSPEND;
618 case OTG_STATE_B_IDLE:
619 musb->int_usb &= ~MUSB_INTR_SUSPEND;
622 WARNING("bogus %s RESUME (%s)\n",
624 usb_otg_state_string(musb->xceiv->otg->state));
629 /* see manual for the order of the tests */
630 if (int_usb & MUSB_INTR_SESSREQ) {
631 void __iomem *mbase = musb->mregs;
633 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS
634 && (devctl & MUSB_DEVCTL_BDEVICE)) {
635 musb_dbg(musb, "SessReq while on B state");
639 musb_dbg(musb, "SESSION_REQUEST (%s)",
640 usb_otg_state_string(musb->xceiv->otg->state));
642 /* IRQ arrives from ID pin sense or (later, if VBUS power
643 * is removed) SRP. responses are time critical:
644 * - turn on VBUS (with silicon-specific mechanism)
645 * - go through A_WAIT_VRISE
646 * - ... to A_WAIT_BCON.
647 * a_wait_vrise_tmout triggers VBUS_ERROR transitions
649 musb_writeb(mbase, MUSB_DEVCTL, MUSB_DEVCTL_SESSION);
650 musb->ep0_stage = MUSB_EP0_START;
651 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
653 musb_platform_set_vbus(musb, 1);
655 handled = IRQ_HANDLED;
658 if (int_usb & MUSB_INTR_VBUSERROR) {
661 /* During connection as an A-Device, we may see a short
662 * current spikes causing voltage drop, because of cable
663 * and peripheral capacitance combined with vbus draw.
664 * (So: less common with truly self-powered devices, where
665 * vbus doesn't act like a power supply.)
667 * Such spikes are short; usually less than ~500 usec, max
668 * of ~2 msec. That is, they're not sustained overcurrent
669 * errors, though they're reported using VBUSERROR irqs.
671 * Workarounds: (a) hardware: use self powered devices.
672 * (b) software: ignore non-repeated VBUS errors.
674 * REVISIT: do delays from lots of DEBUG_KERNEL checks
675 * make trouble here, keeping VBUS < 4.4V ?
677 switch (musb->xceiv->otg->state) {
678 case OTG_STATE_A_HOST:
679 /* recovery is dicey once we've gotten past the
680 * initial stages of enumeration, but if VBUS
681 * stayed ok at the other end of the link, and
682 * another reset is due (at least for high speed,
683 * to redo the chirp etc), it might work OK...
685 case OTG_STATE_A_WAIT_BCON:
686 case OTG_STATE_A_WAIT_VRISE:
687 if (musb->vbuserr_retry) {
688 void __iomem *mbase = musb->mregs;
690 musb->vbuserr_retry--;
692 devctl |= MUSB_DEVCTL_SESSION;
693 musb_writeb(mbase, MUSB_DEVCTL, devctl);
695 musb->port1_status |=
696 USB_PORT_STAT_OVERCURRENT
697 | (USB_PORT_STAT_C_OVERCURRENT << 16);
704 dev_printk(ignore ? KERN_DEBUG : KERN_ERR, musb->controller,
705 "VBUS_ERROR in %s (%02x, %s), retry #%d, port1 %08x\n",
706 usb_otg_state_string(musb->xceiv->otg->state),
709 switch (devctl & MUSB_DEVCTL_VBUS) {
710 case 0 << MUSB_DEVCTL_VBUS_SHIFT:
711 s = "<SessEnd"; break;
712 case 1 << MUSB_DEVCTL_VBUS_SHIFT:
713 s = "<AValid"; break;
714 case 2 << MUSB_DEVCTL_VBUS_SHIFT:
715 s = "<VBusValid"; break;
716 /* case 3 << MUSB_DEVCTL_VBUS_SHIFT: */
720 VBUSERR_RETRY_COUNT - musb->vbuserr_retry,
723 /* go through A_WAIT_VFALL then start a new session */
725 musb_platform_set_vbus(musb, 0);
726 handled = IRQ_HANDLED;
729 if (int_usb & MUSB_INTR_SUSPEND) {
730 musb_dbg(musb, "SUSPEND (%s) devctl %02x",
731 usb_otg_state_string(musb->xceiv->otg->state), devctl);
732 handled = IRQ_HANDLED;
734 switch (musb->xceiv->otg->state) {
735 case OTG_STATE_A_PERIPHERAL:
736 /* We also come here if the cable is removed, since
737 * this silicon doesn't report ID-no-longer-grounded.
739 * We depend on T(a_wait_bcon) to shut us down, and
740 * hope users don't do anything dicey during this
741 * undesired detour through A_WAIT_BCON.
744 musb_host_resume_root_hub(musb);
745 musb_root_disconnect(musb);
746 musb_platform_try_idle(musb, jiffies
747 + msecs_to_jiffies(musb->a_wait_bcon
748 ? : OTG_TIME_A_WAIT_BCON));
751 case OTG_STATE_B_IDLE:
752 if (!musb->is_active)
754 case OTG_STATE_B_PERIPHERAL:
755 musb_g_suspend(musb);
756 musb->is_active = musb->g.b_hnp_enable;
757 if (musb->is_active) {
758 musb->xceiv->otg->state = OTG_STATE_B_WAIT_ACON;
759 musb_dbg(musb, "HNP: Setting timer for b_ase0_brst");
760 mod_timer(&musb->otg_timer, jiffies
762 OTG_TIME_B_ASE0_BRST));
765 case OTG_STATE_A_WAIT_BCON:
766 if (musb->a_wait_bcon != 0)
767 musb_platform_try_idle(musb, jiffies
768 + msecs_to_jiffies(musb->a_wait_bcon));
770 case OTG_STATE_A_HOST:
771 musb->xceiv->otg->state = OTG_STATE_A_SUSPEND;
772 musb->is_active = musb->hcd->self.b_hnp_enable;
774 case OTG_STATE_B_HOST:
775 /* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */
776 musb_dbg(musb, "REVISIT: SUSPEND as B_HOST");
779 /* "should not happen" */
785 if (int_usb & MUSB_INTR_CONNECT) {
786 struct usb_hcd *hcd = musb->hcd;
788 handled = IRQ_HANDLED;
791 musb->ep0_stage = MUSB_EP0_START;
793 musb->intrtxe = musb->epmask;
794 musb_writew(musb->mregs, MUSB_INTRTXE, musb->intrtxe);
795 musb->intrrxe = musb->epmask & 0xfffe;
796 musb_writew(musb->mregs, MUSB_INTRRXE, musb->intrrxe);
797 musb_writeb(musb->mregs, MUSB_INTRUSBE, 0xf7);
798 musb->port1_status &= ~(USB_PORT_STAT_LOW_SPEED
799 |USB_PORT_STAT_HIGH_SPEED
800 |USB_PORT_STAT_ENABLE
802 musb->port1_status |= USB_PORT_STAT_CONNECTION
803 |(USB_PORT_STAT_C_CONNECTION << 16);
805 /* high vs full speed is just a guess until after reset */
806 if (devctl & MUSB_DEVCTL_LSDEV)
807 musb->port1_status |= USB_PORT_STAT_LOW_SPEED;
809 /* indicate new connection to OTG machine */
810 switch (musb->xceiv->otg->state) {
811 case OTG_STATE_B_PERIPHERAL:
812 if (int_usb & MUSB_INTR_SUSPEND) {
813 musb_dbg(musb, "HNP: SUSPEND+CONNECT, now b_host");
814 int_usb &= ~MUSB_INTR_SUSPEND;
817 musb_dbg(musb, "CONNECT as b_peripheral???");
819 case OTG_STATE_B_WAIT_ACON:
820 musb_dbg(musb, "HNP: CONNECT, now b_host");
822 musb->xceiv->otg->state = OTG_STATE_B_HOST;
824 musb->hcd->self.is_b_host = 1;
825 del_timer(&musb->otg_timer);
828 if ((devctl & MUSB_DEVCTL_VBUS)
829 == (3 << MUSB_DEVCTL_VBUS_SHIFT)) {
830 musb->xceiv->otg->state = OTG_STATE_A_HOST;
832 hcd->self.is_b_host = 0;
837 musb_host_poke_root_hub(musb);
839 musb_dbg(musb, "CONNECT (%s) devctl %02x",
840 usb_otg_state_string(musb->xceiv->otg->state), devctl);
843 if (int_usb & MUSB_INTR_DISCONNECT) {
844 musb_dbg(musb, "DISCONNECT (%s) as %s, devctl %02x",
845 usb_otg_state_string(musb->xceiv->otg->state),
846 MUSB_MODE(musb), devctl);
847 handled = IRQ_HANDLED;
849 switch (musb->xceiv->otg->state) {
850 case OTG_STATE_A_HOST:
851 case OTG_STATE_A_SUSPEND:
852 musb_host_resume_root_hub(musb);
853 musb_root_disconnect(musb);
854 if (musb->a_wait_bcon != 0)
855 musb_platform_try_idle(musb, jiffies
856 + msecs_to_jiffies(musb->a_wait_bcon));
858 case OTG_STATE_B_HOST:
859 /* REVISIT this behaves for "real disconnect"
860 * cases; make sure the other transitions from
861 * from B_HOST act right too. The B_HOST code
862 * in hnp_stop() is currently not used...
864 musb_root_disconnect(musb);
866 musb->hcd->self.is_b_host = 0;
867 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
869 musb_g_disconnect(musb);
871 case OTG_STATE_A_PERIPHERAL:
873 musb_root_disconnect(musb);
875 case OTG_STATE_B_WAIT_ACON:
877 case OTG_STATE_B_PERIPHERAL:
878 case OTG_STATE_B_IDLE:
879 musb_g_disconnect(musb);
882 WARNING("unhandled DISCONNECT transition (%s)\n",
883 usb_otg_state_string(musb->xceiv->otg->state));
888 /* mentor saves a bit: bus reset and babble share the same irq.
889 * only host sees babble; only peripheral sees bus reset.
891 if (int_usb & MUSB_INTR_RESET) {
892 handled = IRQ_HANDLED;
893 if (devctl & MUSB_DEVCTL_HM) {
895 * When BABBLE happens what we can depends on which
896 * platform MUSB is running, because some platforms
897 * implemented proprietary means for 'recovering' from
898 * Babble conditions. One such platform is AM335x. In
899 * most cases, however, the only thing we can do is
902 dev_err(musb->controller, "Babble\n");
904 if (is_host_active(musb))
905 musb_recover_from_babble(musb);
907 musb_dbg(musb, "BUS RESET as %s",
908 usb_otg_state_string(musb->xceiv->otg->state));
909 switch (musb->xceiv->otg->state) {
910 case OTG_STATE_A_SUSPEND:
913 case OTG_STATE_A_WAIT_BCON: /* OPT TD.4.7-900ms */
914 /* never use invalid T(a_wait_bcon) */
915 musb_dbg(musb, "HNP: in %s, %d msec timeout",
916 usb_otg_state_string(musb->xceiv->otg->state),
918 mod_timer(&musb->otg_timer, jiffies
919 + msecs_to_jiffies(TA_WAIT_BCON(musb)));
921 case OTG_STATE_A_PERIPHERAL:
922 del_timer(&musb->otg_timer);
925 case OTG_STATE_B_WAIT_ACON:
926 musb_dbg(musb, "HNP: RESET (%s), to b_peripheral",
927 usb_otg_state_string(musb->xceiv->otg->state));
928 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
931 case OTG_STATE_B_IDLE:
932 musb->xceiv->otg->state = OTG_STATE_B_PERIPHERAL;
934 case OTG_STATE_B_PERIPHERAL:
938 musb_dbg(musb, "Unhandled BUS RESET as %s",
939 usb_otg_state_string(musb->xceiv->otg->state));
945 /* REVISIT ... this would be for multiplexing periodic endpoints, or
946 * supporting transfer phasing to prevent exceeding ISO bandwidth
947 * limits of a given frame or microframe.
949 * It's not needed for peripheral side, which dedicates endpoints;
950 * though it _might_ use SOF irqs for other purposes.
952 * And it's not currently needed for host side, which also dedicates
953 * endpoints, relies on TX/RX interval registers, and isn't claimed
954 * to support ISO transfers yet.
956 if (int_usb & MUSB_INTR_SOF) {
957 void __iomem *mbase = musb->mregs;
958 struct musb_hw_ep *ep;
962 dev_dbg(musb->controller, "START_OF_FRAME\n");
963 handled = IRQ_HANDLED;
965 /* start any periodic Tx transfers waiting for current frame */
966 frame = musb_readw(mbase, MUSB_FRAME);
967 ep = musb->endpoints;
968 for (epnum = 1; (epnum < musb->nr_endpoints)
969 && (musb->epmask >= (1 << epnum));
972 * FIXME handle framecounter wraps (12 bits)
973 * eliminate duplicated StartUrb logic
975 if (ep->dwWaitFrame >= frame) {
977 pr_debug("SOF --> periodic TX%s on %d\n",
978 ep->tx_channel ? " DMA" : "",
981 musb_h_tx_start(musb, epnum);
983 cppi_hostdma_start(musb, epnum);
985 } /* end of for loop */
989 schedule_work(&musb->irq_work);
994 /*-------------------------------------------------------------------------*/
996 static void musb_disable_interrupts(struct musb *musb)
998 void __iomem *mbase = musb->mregs;
1001 /* disable interrupts */
1002 musb_writeb(mbase, MUSB_INTRUSBE, 0);
1004 musb_writew(mbase, MUSB_INTRTXE, 0);
1006 musb_writew(mbase, MUSB_INTRRXE, 0);
1008 /* flush pending interrupts */
1009 temp = musb_readb(mbase, MUSB_INTRUSB);
1010 temp = musb_readw(mbase, MUSB_INTRTX);
1011 temp = musb_readw(mbase, MUSB_INTRRX);
1014 static void musb_enable_interrupts(struct musb *musb)
1016 void __iomem *regs = musb->mregs;
1018 /* Set INT enable registers, enable interrupts */
1019 musb->intrtxe = musb->epmask;
1020 musb_writew(regs, MUSB_INTRTXE, musb->intrtxe);
1021 musb->intrrxe = musb->epmask & 0xfffe;
1022 musb_writew(regs, MUSB_INTRRXE, musb->intrrxe);
1023 musb_writeb(regs, MUSB_INTRUSBE, 0xf7);
1027 static void musb_generic_disable(struct musb *musb)
1029 void __iomem *mbase = musb->mregs;
1031 musb_disable_interrupts(musb);
1034 musb_writeb(mbase, MUSB_DEVCTL, 0);
1038 * Program the HDRC to start (enable interrupts, dma, etc.).
1040 void musb_start(struct musb *musb)
1042 void __iomem *regs = musb->mregs;
1043 u8 devctl = musb_readb(regs, MUSB_DEVCTL);
1046 musb_dbg(musb, "<== devctl %02x", devctl);
1048 musb_enable_interrupts(musb);
1049 musb_writeb(regs, MUSB_TESTMODE, 0);
1051 power = MUSB_POWER_ISOUPDATE;
1053 * treating UNKNOWN as unspecified maximum speed, in which case
1054 * we will default to high-speed.
1056 if (musb->config->maximum_speed == USB_SPEED_HIGH ||
1057 musb->config->maximum_speed == USB_SPEED_UNKNOWN)
1058 power |= MUSB_POWER_HSENAB;
1059 musb_writeb(regs, MUSB_POWER, power);
1061 musb->is_active = 0;
1062 devctl = musb_readb(regs, MUSB_DEVCTL);
1063 devctl &= ~MUSB_DEVCTL_SESSION;
1065 /* session started after:
1066 * (a) ID-grounded irq, host mode;
1067 * (b) vbus present/connect IRQ, peripheral mode;
1068 * (c) peripheral initiates, using SRP
1070 if (musb->port_mode != MUSB_PORT_MODE_HOST &&
1071 musb->xceiv->otg->state != OTG_STATE_A_WAIT_BCON &&
1072 (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) {
1073 musb->is_active = 1;
1075 devctl |= MUSB_DEVCTL_SESSION;
1078 musb_platform_enable(musb);
1079 musb_writeb(regs, MUSB_DEVCTL, devctl);
1083 * Make the HDRC stop (disable interrupts, etc.);
1084 * reversible by musb_start
1085 * called on gadget driver unregister
1086 * with controller locked, irqs blocked
1087 * acts as a NOP unless some role activated the hardware
1089 void musb_stop(struct musb *musb)
1091 /* stop IRQs, timers, ... */
1092 musb_platform_disable(musb);
1093 musb_generic_disable(musb);
1094 musb_dbg(musb, "HDRC disabled");
1097 * - mark host and/or peripheral drivers unusable/inactive
1098 * - disable DMA (and enable it in HdrcStart)
1099 * - make sure we can musb_start() after musb_stop(); with
1100 * OTG mode, gadget driver module rmmod/modprobe cycles that
1103 musb_platform_try_idle(musb, 0);
1106 /*-------------------------------------------------------------------------*/
1109 * The silicon either has hard-wired endpoint configurations, or else
1110 * "dynamic fifo" sizing. The driver has support for both, though at this
1111 * writing only the dynamic sizing is very well tested. Since we switched
1112 * away from compile-time hardware parameters, we can no longer rely on
1113 * dead code elimination to leave only the relevant one in the object file.
1115 * We don't currently use dynamic fifo setup capability to do anything
1116 * more than selecting one of a bunch of predefined configurations.
1118 static ushort fifo_mode;
1120 /* "modprobe ... fifo_mode=1" etc */
1121 module_param(fifo_mode, ushort, 0);
1122 MODULE_PARM_DESC(fifo_mode, "initial endpoint configuration");
1125 * tables defining fifo_mode values. define more if you like.
1126 * for host side, make sure both halves of ep1 are set up.
1129 /* mode 0 - fits in 2KB */
1130 static struct musb_fifo_cfg mode_0_cfg[] = {
1131 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
1132 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
1133 { .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, },
1134 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, },
1135 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, },
1138 /* mode 1 - fits in 4KB */
1139 static struct musb_fifo_cfg mode_1_cfg[] = {
1140 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, },
1141 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, },
1142 { .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, .mode = BUF_DOUBLE, },
1143 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, },
1144 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, },
1147 /* mode 2 - fits in 4KB */
1148 static struct musb_fifo_cfg mode_2_cfg[] = {
1149 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
1150 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
1151 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
1152 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
1153 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, },
1154 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, },
1157 /* mode 3 - fits in 4KB */
1158 static struct musb_fifo_cfg mode_3_cfg[] = {
1159 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, },
1160 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, },
1161 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
1162 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
1163 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, },
1164 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, },
1167 /* mode 4 - fits in 16KB */
1168 static struct musb_fifo_cfg mode_4_cfg[] = {
1169 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
1170 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
1171 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
1172 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
1173 { .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, },
1174 { .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, },
1175 { .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, },
1176 { .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, },
1177 { .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, },
1178 { .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, },
1179 { .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 512, },
1180 { .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 512, },
1181 { .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 512, },
1182 { .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 512, },
1183 { .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 512, },
1184 { .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 512, },
1185 { .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 512, },
1186 { .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 512, },
1187 { .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 256, },
1188 { .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 64, },
1189 { .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 256, },
1190 { .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 64, },
1191 { .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 256, },
1192 { .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 64, },
1193 { .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 4096, },
1194 { .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, },
1195 { .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
1198 /* mode 5 - fits in 8KB */
1199 static struct musb_fifo_cfg mode_5_cfg[] = {
1200 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
1201 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
1202 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
1203 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
1204 { .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, },
1205 { .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, },
1206 { .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, },
1207 { .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, },
1208 { .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, },
1209 { .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, },
1210 { .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 32, },
1211 { .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 32, },
1212 { .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 32, },
1213 { .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 32, },
1214 { .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 32, },
1215 { .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 32, },
1216 { .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 32, },
1217 { .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 32, },
1218 { .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 32, },
1219 { .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 32, },
1220 { .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 32, },
1221 { .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 32, },
1222 { .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 32, },
1223 { .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 32, },
1224 { .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 512, },
1225 { .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, },
1226 { .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, },
1230 * configure a fifo; for non-shared endpoints, this may be called
1231 * once for a tx fifo and once for an rx fifo.
1233 * returns negative errno or offset for next fifo.
1236 fifo_setup(struct musb *musb, struct musb_hw_ep *hw_ep,
1237 const struct musb_fifo_cfg *cfg, u16 offset)
1239 void __iomem *mbase = musb->mregs;
1241 u16 maxpacket = cfg->maxpacket;
1242 u16 c_off = offset >> 3;
1245 /* expect hw_ep has already been zero-initialized */
1247 size = ffs(max(maxpacket, (u16) 8)) - 1;
1248 maxpacket = 1 << size;
1251 if (cfg->mode == BUF_DOUBLE) {
1252 if ((offset + (maxpacket << 1)) >
1253 (1 << (musb->config->ram_bits + 2)))
1255 c_size |= MUSB_FIFOSZ_DPB;
1257 if ((offset + maxpacket) > (1 << (musb->config->ram_bits + 2)))
1261 /* configure the FIFO */
1262 musb_writeb(mbase, MUSB_INDEX, hw_ep->epnum);
1264 /* EP0 reserved endpoint for control, bidirectional;
1265 * EP1 reserved for bulk, two unidirectional halves.
1267 if (hw_ep->epnum == 1)
1268 musb->bulk_ep = hw_ep;
1269 /* REVISIT error check: be sure ep0 can both rx and tx ... */
1270 switch (cfg->style) {
1272 musb_write_txfifosz(mbase, c_size);
1273 musb_write_txfifoadd(mbase, c_off);
1274 hw_ep->tx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB);
1275 hw_ep->max_packet_sz_tx = maxpacket;
1278 musb_write_rxfifosz(mbase, c_size);
1279 musb_write_rxfifoadd(mbase, c_off);
1280 hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB);
1281 hw_ep->max_packet_sz_rx = maxpacket;
1284 musb_write_txfifosz(mbase, c_size);
1285 musb_write_txfifoadd(mbase, c_off);
1286 hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB);
1287 hw_ep->max_packet_sz_rx = maxpacket;
1289 musb_write_rxfifosz(mbase, c_size);
1290 musb_write_rxfifoadd(mbase, c_off);
1291 hw_ep->tx_double_buffered = hw_ep->rx_double_buffered;
1292 hw_ep->max_packet_sz_tx = maxpacket;
1294 hw_ep->is_shared_fifo = true;
1298 /* NOTE rx and tx endpoint irqs aren't managed separately,
1299 * which happens to be ok
1301 musb->epmask |= (1 << hw_ep->epnum);
1303 return offset + (maxpacket << ((c_size & MUSB_FIFOSZ_DPB) ? 1 : 0));
1306 static struct musb_fifo_cfg ep0_cfg = {
1307 .style = FIFO_RXTX, .maxpacket = 64,
1310 static int ep_config_from_table(struct musb *musb)
1312 const struct musb_fifo_cfg *cfg;
1315 struct musb_hw_ep *hw_ep = musb->endpoints;
1317 if (musb->config->fifo_cfg) {
1318 cfg = musb->config->fifo_cfg;
1319 n = musb->config->fifo_cfg_size;
1323 switch (fifo_mode) {
1329 n = ARRAY_SIZE(mode_0_cfg);
1333 n = ARRAY_SIZE(mode_1_cfg);
1337 n = ARRAY_SIZE(mode_2_cfg);
1341 n = ARRAY_SIZE(mode_3_cfg);
1345 n = ARRAY_SIZE(mode_4_cfg);
1349 n = ARRAY_SIZE(mode_5_cfg);
1353 pr_debug("%s: setup fifo_mode %d\n", musb_driver_name, fifo_mode);
1357 offset = fifo_setup(musb, hw_ep, &ep0_cfg, 0);
1358 /* assert(offset > 0) */
1360 /* NOTE: for RTL versions >= 1.400 EPINFO and RAMINFO would
1361 * be better than static musb->config->num_eps and DYN_FIFO_SIZE...
1364 for (i = 0; i < n; i++) {
1365 u8 epn = cfg->hw_ep_num;
1367 if (epn >= musb->config->num_eps) {
1368 pr_debug("%s: invalid ep %d\n",
1369 musb_driver_name, epn);
1372 offset = fifo_setup(musb, hw_ep + epn, cfg++, offset);
1374 pr_debug("%s: mem overrun, ep %d\n",
1375 musb_driver_name, epn);
1379 musb->nr_endpoints = max(epn, musb->nr_endpoints);
1382 pr_debug("%s: %d/%d max ep, %d/%d memory\n",
1384 n + 1, musb->config->num_eps * 2 - 1,
1385 offset, (1 << (musb->config->ram_bits + 2)));
1387 if (!musb->bulk_ep) {
1388 pr_debug("%s: missing bulk\n", musb_driver_name);
1397 * ep_config_from_hw - when MUSB_C_DYNFIFO_DEF is false
1398 * @param musb the controller
1400 static int ep_config_from_hw(struct musb *musb)
1403 struct musb_hw_ep *hw_ep;
1404 void __iomem *mbase = musb->mregs;
1407 musb_dbg(musb, "<== static silicon ep config");
1409 /* FIXME pick up ep0 maxpacket size */
1411 for (epnum = 1; epnum < musb->config->num_eps; epnum++) {
1412 musb_ep_select(mbase, epnum);
1413 hw_ep = musb->endpoints + epnum;
1415 ret = musb_read_fifosize(musb, hw_ep, epnum);
1419 /* FIXME set up hw_ep->{rx,tx}_double_buffered */
1421 /* pick an RX/TX endpoint for bulk */
1422 if (hw_ep->max_packet_sz_tx < 512
1423 || hw_ep->max_packet_sz_rx < 512)
1426 /* REVISIT: this algorithm is lazy, we should at least
1427 * try to pick a double buffered endpoint.
1431 musb->bulk_ep = hw_ep;
1434 if (!musb->bulk_ep) {
1435 pr_debug("%s: missing bulk\n", musb_driver_name);
1442 enum { MUSB_CONTROLLER_MHDRC, MUSB_CONTROLLER_HDRC, };
1444 /* Initialize MUSB (M)HDRC part of the USB hardware subsystem;
1445 * configure endpoints, or take their config from silicon
1447 static int musb_core_init(u16 musb_type, struct musb *musb)
1452 void __iomem *mbase = musb->mregs;
1456 /* log core options (read using indexed model) */
1457 reg = musb_read_configdata(mbase);
1459 strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8");
1460 if (reg & MUSB_CONFIGDATA_DYNFIFO) {
1461 strcat(aInfo, ", dyn FIFOs");
1462 musb->dyn_fifo = true;
1464 if (reg & MUSB_CONFIGDATA_MPRXE) {
1465 strcat(aInfo, ", bulk combine");
1466 musb->bulk_combine = true;
1468 if (reg & MUSB_CONFIGDATA_MPTXE) {
1469 strcat(aInfo, ", bulk split");
1470 musb->bulk_split = true;
1472 if (reg & MUSB_CONFIGDATA_HBRXE) {
1473 strcat(aInfo, ", HB-ISO Rx");
1474 musb->hb_iso_rx = true;
1476 if (reg & MUSB_CONFIGDATA_HBTXE) {
1477 strcat(aInfo, ", HB-ISO Tx");
1478 musb->hb_iso_tx = true;
1480 if (reg & MUSB_CONFIGDATA_SOFTCONE)
1481 strcat(aInfo, ", SoftConn");
1483 pr_debug("%s: ConfigData=0x%02x (%s)\n", musb_driver_name, reg, aInfo);
1485 if (MUSB_CONTROLLER_MHDRC == musb_type) {
1486 musb->is_multipoint = 1;
1489 musb->is_multipoint = 0;
1491 #ifndef CONFIG_USB_OTG_BLACKLIST_HUB
1492 pr_err("%s: kernel must blacklist external hubs\n",
1497 /* log release info */
1498 musb->hwvers = musb_read_hwvers(mbase);
1499 pr_debug("%s: %sHDRC RTL version %d.%d%s\n",
1500 musb_driver_name, type, MUSB_HWVERS_MAJOR(musb->hwvers),
1501 MUSB_HWVERS_MINOR(musb->hwvers),
1502 (musb->hwvers & MUSB_HWVERS_RC) ? "RC" : "");
1505 musb_configure_ep0(musb);
1507 /* discover endpoint configuration */
1508 musb->nr_endpoints = 1;
1512 status = ep_config_from_table(musb);
1514 status = ep_config_from_hw(musb);
1519 /* finish init, and print endpoint config */
1520 for (i = 0; i < musb->nr_endpoints; i++) {
1521 struct musb_hw_ep *hw_ep = musb->endpoints + i;
1523 hw_ep->fifo = musb->io.fifo_offset(i) + mbase;
1524 #if IS_ENABLED(CONFIG_USB_MUSB_TUSB6010)
1525 if (musb->io.quirks & MUSB_IN_TUSB) {
1526 hw_ep->fifo_async = musb->async + 0x400 +
1527 musb->io.fifo_offset(i);
1528 hw_ep->fifo_sync = musb->sync + 0x400 +
1529 musb->io.fifo_offset(i);
1530 hw_ep->fifo_sync_va =
1531 musb->sync_va + 0x400 + musb->io.fifo_offset(i);
1534 hw_ep->conf = mbase - 0x400 + TUSB_EP0_CONF;
1536 hw_ep->conf = mbase + 0x400 +
1537 (((i - 1) & 0xf) << 2);
1541 hw_ep->regs = musb->io.ep_offset(i, 0) + mbase;
1542 hw_ep->rx_reinit = 1;
1543 hw_ep->tx_reinit = 1;
1545 if (hw_ep->max_packet_sz_tx) {
1546 musb_dbg(musb, "%s: hw_ep %d%s, %smax %d",
1547 musb_driver_name, i,
1548 hw_ep->is_shared_fifo ? "shared" : "tx",
1549 hw_ep->tx_double_buffered
1550 ? "doublebuffer, " : "",
1551 hw_ep->max_packet_sz_tx);
1553 if (hw_ep->max_packet_sz_rx && !hw_ep->is_shared_fifo) {
1554 musb_dbg(musb, "%s: hw_ep %d%s, %smax %d",
1555 musb_driver_name, i,
1557 hw_ep->rx_double_buffered
1558 ? "doublebuffer, " : "",
1559 hw_ep->max_packet_sz_rx);
1561 if (!(hw_ep->max_packet_sz_tx || hw_ep->max_packet_sz_rx))
1562 musb_dbg(musb, "hw_ep %d not configured", i);
1568 /*-------------------------------------------------------------------------*/
1571 * handle all the irqs defined by the HDRC core. for now we expect: other
1572 * irq sources (phy, dma, etc) will be handled first, musb->int_* values
1573 * will be assigned, and the irq will already have been acked.
1575 * called in irq context with spinlock held, irqs blocked
1577 irqreturn_t musb_interrupt(struct musb *musb)
1579 irqreturn_t retval = IRQ_NONE;
1580 unsigned long status;
1581 unsigned long epnum;
1584 if (!musb->int_usb && !musb->int_tx && !musb->int_rx)
1587 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
1589 trace_musb_isr(musb);
1592 * According to Mentor Graphics' documentation, flowchart on page 98,
1593 * IRQ should be handled as follows:
1596 * . Session Request IRQ
1601 * . Reset/Babble IRQ
1602 * . SOF IRQ (we're not using this one)
1607 * We will be following that flowchart in order to avoid any problems
1608 * that might arise with internal Finite State Machine.
1612 retval |= musb_stage0_irq(musb, musb->int_usb, devctl);
1614 if (musb->int_tx & 1) {
1615 if (is_host_active(musb))
1616 retval |= musb_h_ep0_irq(musb);
1618 retval |= musb_g_ep0_irq(musb);
1620 /* we have just handled endpoint 0 IRQ, clear it */
1621 musb->int_tx &= ~BIT(0);
1624 status = musb->int_tx;
1626 for_each_set_bit(epnum, &status, 16) {
1627 retval = IRQ_HANDLED;
1628 if (is_host_active(musb))
1629 musb_host_tx(musb, epnum);
1631 musb_g_tx(musb, epnum);
1634 status = musb->int_rx;
1636 for_each_set_bit(epnum, &status, 16) {
1637 retval = IRQ_HANDLED;
1638 if (is_host_active(musb))
1639 musb_host_rx(musb, epnum);
1641 musb_g_rx(musb, epnum);
1646 EXPORT_SYMBOL_GPL(musb_interrupt);
1648 #ifndef CONFIG_MUSB_PIO_ONLY
1649 static bool use_dma = 1;
1651 /* "modprobe ... use_dma=0" etc */
1652 module_param(use_dma, bool, 0644);
1653 MODULE_PARM_DESC(use_dma, "enable/disable use of DMA");
1655 void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit)
1657 /* called with controller lock already held */
1660 if (!is_cppi_enabled(musb)) {
1662 if (is_host_active(musb))
1663 musb_h_ep0_irq(musb);
1665 musb_g_ep0_irq(musb);
1668 /* endpoints 1..15 */
1670 if (is_host_active(musb))
1671 musb_host_tx(musb, epnum);
1673 musb_g_tx(musb, epnum);
1676 if (is_host_active(musb))
1677 musb_host_rx(musb, epnum);
1679 musb_g_rx(musb, epnum);
1683 EXPORT_SYMBOL_GPL(musb_dma_completion);
1689 static int (*musb_phy_callback)(enum musb_vbus_id_status status);
1692 * musb_mailbox - optional phy notifier function
1693 * @status phy state change
1695 * Optionally gets called from the USB PHY. Note that the USB PHY must be
1696 * disabled at the point the phy_callback is registered or unregistered.
1698 int musb_mailbox(enum musb_vbus_id_status status)
1700 if (musb_phy_callback)
1701 return musb_phy_callback(status);
1705 EXPORT_SYMBOL_GPL(musb_mailbox);
1707 /*-------------------------------------------------------------------------*/
1710 musb_mode_show(struct device *dev, struct device_attribute *attr, char *buf)
1712 struct musb *musb = dev_to_musb(dev);
1713 unsigned long flags;
1716 spin_lock_irqsave(&musb->lock, flags);
1717 ret = sprintf(buf, "%s\n", usb_otg_state_string(musb->xceiv->otg->state));
1718 spin_unlock_irqrestore(&musb->lock, flags);
1724 musb_mode_store(struct device *dev, struct device_attribute *attr,
1725 const char *buf, size_t n)
1727 struct musb *musb = dev_to_musb(dev);
1728 unsigned long flags;
1731 spin_lock_irqsave(&musb->lock, flags);
1732 if (sysfs_streq(buf, "host"))
1733 status = musb_platform_set_mode(musb, MUSB_HOST);
1734 else if (sysfs_streq(buf, "peripheral"))
1735 status = musb_platform_set_mode(musb, MUSB_PERIPHERAL);
1736 else if (sysfs_streq(buf, "otg"))
1737 status = musb_platform_set_mode(musb, MUSB_OTG);
1740 spin_unlock_irqrestore(&musb->lock, flags);
1742 return (status == 0) ? n : status;
1744 static DEVICE_ATTR(mode, 0644, musb_mode_show, musb_mode_store);
1747 musb_vbus_store(struct device *dev, struct device_attribute *attr,
1748 const char *buf, size_t n)
1750 struct musb *musb = dev_to_musb(dev);
1751 unsigned long flags;
1754 if (sscanf(buf, "%lu", &val) < 1) {
1755 dev_err(dev, "Invalid VBUS timeout ms value\n");
1759 spin_lock_irqsave(&musb->lock, flags);
1760 /* force T(a_wait_bcon) to be zero/unlimited *OR* valid */
1761 musb->a_wait_bcon = val ? max_t(int, val, OTG_TIME_A_WAIT_BCON) : 0 ;
1762 if (musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON)
1763 musb->is_active = 0;
1764 musb_platform_try_idle(musb, jiffies + msecs_to_jiffies(val));
1765 spin_unlock_irqrestore(&musb->lock, flags);
1771 musb_vbus_show(struct device *dev, struct device_attribute *attr, char *buf)
1773 struct musb *musb = dev_to_musb(dev);
1774 unsigned long flags;
1779 spin_lock_irqsave(&musb->lock, flags);
1780 val = musb->a_wait_bcon;
1781 vbus = musb_platform_get_vbus_status(musb);
1783 /* Use default MUSB method by means of DEVCTL register */
1784 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
1785 if ((devctl & MUSB_DEVCTL_VBUS)
1786 == (3 << MUSB_DEVCTL_VBUS_SHIFT))
1791 spin_unlock_irqrestore(&musb->lock, flags);
1793 return sprintf(buf, "Vbus %s, timeout %lu msec\n",
1794 vbus ? "on" : "off", val);
1796 static DEVICE_ATTR(vbus, 0644, musb_vbus_show, musb_vbus_store);
1798 /* Gadget drivers can't know that a host is connected so they might want
1799 * to start SRP, but users can. This allows userspace to trigger SRP.
1802 musb_srp_store(struct device *dev, struct device_attribute *attr,
1803 const char *buf, size_t n)
1805 struct musb *musb = dev_to_musb(dev);
1808 if (sscanf(buf, "%hu", &srp) != 1
1810 dev_err(dev, "SRP: Value must be 1\n");
1815 musb_g_wakeup(musb);
1819 static DEVICE_ATTR(srp, 0644, NULL, musb_srp_store);
1821 static struct attribute *musb_attributes[] = {
1822 &dev_attr_mode.attr,
1823 &dev_attr_vbus.attr,
1828 static const struct attribute_group musb_attr_group = {
1829 .attrs = musb_attributes,
1832 #define MUSB_QUIRK_B_INVALID_VBUS_91 (MUSB_DEVCTL_BDEVICE | \
1833 (2 << MUSB_DEVCTL_VBUS_SHIFT) | \
1834 MUSB_DEVCTL_SESSION)
1835 #define MUSB_QUIRK_A_DISCONNECT_19 ((3 << MUSB_DEVCTL_VBUS_SHIFT) | \
1836 MUSB_DEVCTL_SESSION)
1839 * Check the musb devctl session bit to determine if we want to
1840 * allow PM runtime for the device. In general, we want to keep things
1841 * active when the session bit is set except after host disconnect.
1843 * Only called from musb_irq_work. If this ever needs to get called
1844 * elsewhere, proper locking must be implemented for musb->session.
1846 static void musb_pm_runtime_check_session(struct musb *musb)
1851 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
1853 /* Handle session status quirks first */
1854 s = MUSB_DEVCTL_FSDEV | MUSB_DEVCTL_LSDEV |
1856 switch (devctl & ~s) {
1857 case MUSB_QUIRK_B_INVALID_VBUS_91:
1858 if (!musb->session && !musb->quirk_invalid_vbus) {
1859 musb->quirk_invalid_vbus = true;
1861 "First invalid vbus, assume no session");
1865 case MUSB_QUIRK_A_DISCONNECT_19:
1868 musb_dbg(musb, "Allow PM on possible host mode disconnect");
1869 pm_runtime_mark_last_busy(musb->controller);
1870 pm_runtime_put_autosuspend(musb->controller);
1871 musb->session = false;
1877 /* No need to do anything if session has not changed */
1878 s = devctl & MUSB_DEVCTL_SESSION;
1879 if (s == musb->session)
1882 /* Block PM or allow PM? */
1884 musb_dbg(musb, "Block PM on active session: %02x", devctl);
1885 error = pm_runtime_get_sync(musb->controller);
1887 dev_err(musb->controller, "Could not enable: %i\n",
1890 musb_dbg(musb, "Allow PM with no session: %02x", devctl);
1891 musb->quirk_invalid_vbus = false;
1892 pm_runtime_mark_last_busy(musb->controller);
1893 pm_runtime_put_autosuspend(musb->controller);
1899 /* Only used to provide driver mode change events */
1900 static void musb_irq_work(struct work_struct *data)
1902 struct musb *musb = container_of(data, struct musb, irq_work);
1904 musb_pm_runtime_check_session(musb);
1906 if (musb->xceiv->otg->state != musb->xceiv_old_state) {
1907 musb->xceiv_old_state = musb->xceiv->otg->state;
1908 sysfs_notify(&musb->controller->kobj, NULL, "mode");
1912 static void musb_recover_from_babble(struct musb *musb)
1917 musb_disable_interrupts(musb);
1920 * wait at least 320 cycles of 60MHz clock. That's 5.3us, we will give
1921 * it some slack and wait for 10us.
1925 ret = musb_platform_recover(musb);
1927 musb_enable_interrupts(musb);
1931 /* drop session bit */
1932 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
1933 devctl &= ~MUSB_DEVCTL_SESSION;
1934 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
1936 /* tell usbcore about it */
1937 musb_root_disconnect(musb);
1940 * When a babble condition occurs, the musb controller
1941 * removes the session bit and the endpoint config is lost.
1944 ret = ep_config_from_table(musb);
1946 ret = ep_config_from_hw(musb);
1948 /* restart session */
1953 /* --------------------------------------------------------------------------
1957 static struct musb *allocate_instance(struct device *dev,
1958 const struct musb_hdrc_config *config, void __iomem *mbase)
1961 struct musb_hw_ep *ep;
1965 musb = devm_kzalloc(dev, sizeof(*musb), GFP_KERNEL);
1969 INIT_LIST_HEAD(&musb->control);
1970 INIT_LIST_HEAD(&musb->in_bulk);
1971 INIT_LIST_HEAD(&musb->out_bulk);
1973 musb->vbuserr_retry = VBUSERR_RETRY_COUNT;
1974 musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;
1975 musb->mregs = mbase;
1976 musb->ctrl_base = mbase;
1977 musb->nIrq = -ENODEV;
1978 musb->config = config;
1979 BUG_ON(musb->config->num_eps > MUSB_C_NUM_EPS);
1980 for (epnum = 0, ep = musb->endpoints;
1981 epnum < musb->config->num_eps;
1987 musb->controller = dev;
1989 ret = musb_host_alloc(musb);
1993 dev_set_drvdata(dev, musb);
2001 static void musb_free(struct musb *musb)
2003 /* this has multiple entry modes. it handles fault cleanup after
2004 * probe(), where things may be partially set up, as well as rmmod
2005 * cleanup after everything's been de-activated.
2009 sysfs_remove_group(&musb->controller->kobj, &musb_attr_group);
2012 if (musb->nIrq >= 0) {
2014 disable_irq_wake(musb->nIrq);
2015 free_irq(musb->nIrq, musb);
2018 musb_host_free(musb);
2021 static void musb_deassert_reset(struct work_struct *work)
2024 unsigned long flags;
2026 musb = container_of(work, struct musb, deassert_reset_work.work);
2028 spin_lock_irqsave(&musb->lock, flags);
2030 if (musb->port1_status & USB_PORT_STAT_RESET)
2031 musb_port_reset(musb, false);
2033 spin_unlock_irqrestore(&musb->lock, flags);
2037 * Perform generic per-controller initialization.
2039 * @dev: the controller (already clocked, etc)
2041 * @ctrl: virtual address of controller registers,
2042 * not yet corrected for platform-specific offsets
2045 musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
2049 struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
2051 /* The driver might handle more features than the board; OK.
2052 * Fail when the board needs a feature that's not enabled.
2055 dev_err(dev, "no platform_data?\n");
2061 musb = allocate_instance(dev, plat->config, ctrl);
2067 spin_lock_init(&musb->lock);
2068 musb->board_set_power = plat->set_power;
2069 musb->min_power = plat->min_power;
2070 musb->ops = plat->platform_ops;
2071 musb->port_mode = plat->mode;
2074 * Initialize the default IO functions. At least omap2430 needs
2075 * these early. We initialize the platform specific IO functions
2078 musb_readb = musb_default_readb;
2079 musb_writeb = musb_default_writeb;
2080 musb_readw = musb_default_readw;
2081 musb_writew = musb_default_writew;
2082 musb_readl = musb_default_readl;
2083 musb_writel = musb_default_writel;
2085 /* The musb_platform_init() call:
2086 * - adjusts musb->mregs
2087 * - sets the musb->isr
2088 * - may initialize an integrated transceiver
2089 * - initializes musb->xceiv, usually by otg_get_phy()
2090 * - stops powering VBUS
2092 * There are various transceiver configurations. Blackfin,
2093 * DaVinci, TUSB60x0, and others integrate them. OMAP3 uses
2094 * external/discrete ones in various flavors (twl4030 family,
2095 * isp1504, non-OTG, etc) mostly hooking up through ULPI.
2097 status = musb_platform_init(musb);
2106 if (musb->ops->quirks)
2107 musb->io.quirks = musb->ops->quirks;
2109 /* Most devices use indexed offset or flat offset */
2110 if (musb->io.quirks & MUSB_INDEXED_EP) {
2111 musb->io.ep_offset = musb_indexed_ep_offset;
2112 musb->io.ep_select = musb_indexed_ep_select;
2114 musb->io.ep_offset = musb_flat_ep_offset;
2115 musb->io.ep_select = musb_flat_ep_select;
2118 /* At least tusb6010 has its own offsets */
2119 if (musb->ops->ep_offset)
2120 musb->io.ep_offset = musb->ops->ep_offset;
2121 if (musb->ops->ep_select)
2122 musb->io.ep_select = musb->ops->ep_select;
2124 if (musb->ops->fifo_mode)
2125 fifo_mode = musb->ops->fifo_mode;
2129 if (musb->ops->fifo_offset)
2130 musb->io.fifo_offset = musb->ops->fifo_offset;
2132 musb->io.fifo_offset = musb_default_fifo_offset;
2134 if (musb->ops->busctl_offset)
2135 musb->io.busctl_offset = musb->ops->busctl_offset;
2137 musb->io.busctl_offset = musb_default_busctl_offset;
2139 if (musb->ops->readb)
2140 musb_readb = musb->ops->readb;
2141 if (musb->ops->writeb)
2142 musb_writeb = musb->ops->writeb;
2143 if (musb->ops->readw)
2144 musb_readw = musb->ops->readw;
2145 if (musb->ops->writew)
2146 musb_writew = musb->ops->writew;
2147 if (musb->ops->readl)
2148 musb_readl = musb->ops->readl;
2149 if (musb->ops->writel)
2150 musb_writel = musb->ops->writel;
2152 #ifndef CONFIG_MUSB_PIO_ONLY
2153 if (!musb->ops->dma_init || !musb->ops->dma_exit) {
2154 dev_err(dev, "DMA controller not set\n");
2158 musb_dma_controller_create = musb->ops->dma_init;
2159 musb_dma_controller_destroy = musb->ops->dma_exit;
2162 if (musb->ops->read_fifo)
2163 musb->io.read_fifo = musb->ops->read_fifo;
2165 musb->io.read_fifo = musb_default_read_fifo;
2167 if (musb->ops->write_fifo)
2168 musb->io.write_fifo = musb->ops->write_fifo;
2170 musb->io.write_fifo = musb_default_write_fifo;
2172 if (!musb->xceiv->io_ops) {
2173 musb->xceiv->io_dev = musb->controller;
2174 musb->xceiv->io_priv = musb->mregs;
2175 musb->xceiv->io_ops = &musb_ulpi_access;
2178 if (musb->ops->phy_callback)
2179 musb_phy_callback = musb->ops->phy_callback;
2182 * We need musb_read/write functions initialized for PM.
2183 * Note that at least 2430 glue needs autosuspend delay
2184 * somewhere above 300 ms for the hardware to idle properly
2185 * after disconnecting the cable in host mode. Let's use
2186 * 500 ms for some margin.
2188 pm_runtime_use_autosuspend(musb->controller);
2189 pm_runtime_set_autosuspend_delay(musb->controller, 500);
2190 pm_runtime_enable(musb->controller);
2191 pm_runtime_get_sync(musb->controller);
2193 status = usb_phy_init(musb->xceiv);
2195 goto err_usb_phy_init;
2197 if (use_dma && dev->dma_mask) {
2198 musb->dma_controller =
2199 musb_dma_controller_create(musb, musb->mregs);
2200 if (IS_ERR(musb->dma_controller)) {
2201 status = PTR_ERR(musb->dma_controller);
2206 /* be sure interrupts are disabled before connecting ISR */
2207 musb_platform_disable(musb);
2208 musb_generic_disable(musb);
2210 /* Init IRQ workqueue before request_irq */
2211 INIT_WORK(&musb->irq_work, musb_irq_work);
2212 INIT_DELAYED_WORK(&musb->deassert_reset_work, musb_deassert_reset);
2213 INIT_DELAYED_WORK(&musb->finish_resume_work, musb_host_finish_resume);
2215 /* setup musb parts of the core (especially endpoints) */
2216 status = musb_core_init(plat->config->multipoint
2217 ? MUSB_CONTROLLER_MHDRC
2218 : MUSB_CONTROLLER_HDRC, musb);
2222 setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb);
2224 /* attach to the IRQ */
2225 if (request_irq(nIrq, musb->isr, 0, dev_name(dev), musb)) {
2226 dev_err(dev, "request_irq %d failed!\n", nIrq);
2231 /* FIXME this handles wakeup irqs wrong */
2232 if (enable_irq_wake(nIrq) == 0) {
2234 device_init_wakeup(dev, 1);
2239 /* program PHY to use external vBus if required */
2240 if (plat->extvbus) {
2241 u8 busctl = musb_read_ulpi_buscontrol(musb->mregs);
2242 busctl |= MUSB_ULPI_USE_EXTVBUS;
2243 musb_write_ulpi_buscontrol(musb->mregs, busctl);
2246 if (musb->xceiv->otg->default_a) {
2247 MUSB_HST_MODE(musb);
2248 musb->xceiv->otg->state = OTG_STATE_A_IDLE;
2250 MUSB_DEV_MODE(musb);
2251 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
2254 switch (musb->port_mode) {
2255 case MUSB_PORT_MODE_HOST:
2256 status = musb_host_setup(musb, plat->power);
2259 status = musb_platform_set_mode(musb, MUSB_HOST);
2261 case MUSB_PORT_MODE_GADGET:
2262 status = musb_gadget_setup(musb);
2265 status = musb_platform_set_mode(musb, MUSB_PERIPHERAL);
2267 case MUSB_PORT_MODE_DUAL_ROLE:
2268 status = musb_host_setup(musb, plat->power);
2271 status = musb_gadget_setup(musb);
2273 musb_host_cleanup(musb);
2276 status = musb_platform_set_mode(musb, MUSB_OTG);
2279 dev_err(dev, "unsupported port mode %d\n", musb->port_mode);
2286 status = musb_init_debugfs(musb);
2290 status = sysfs_create_group(&musb->controller->kobj, &musb_attr_group);
2294 pm_runtime_mark_last_busy(musb->controller);
2295 pm_runtime_put_autosuspend(musb->controller);
2300 musb_exit_debugfs(musb);
2303 musb_gadget_cleanup(musb);
2304 musb_host_cleanup(musb);
2307 cancel_work_sync(&musb->irq_work);
2308 cancel_delayed_work_sync(&musb->finish_resume_work);
2309 cancel_delayed_work_sync(&musb->deassert_reset_work);
2310 if (musb->dma_controller)
2311 musb_dma_controller_destroy(musb->dma_controller);
2314 usb_phy_shutdown(musb->xceiv);
2317 pm_runtime_dont_use_autosuspend(musb->controller);
2318 pm_runtime_put_sync(musb->controller);
2319 pm_runtime_disable(musb->controller);
2323 device_init_wakeup(dev, 0);
2324 musb_platform_exit(musb);
2327 dev_err(musb->controller,
2328 "musb_init_controller failed with status %d\n", status);
2338 /*-------------------------------------------------------------------------*/
2340 /* all implementations (PCI bridge to FPGA, VLYNQ, etc) should just
2341 * bridge to a platform device; this driver then suffices.
2343 static int musb_probe(struct platform_device *pdev)
2345 struct device *dev = &pdev->dev;
2346 int irq = platform_get_irq_byname(pdev, "mc");
2347 struct resource *iomem;
2353 iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2354 base = devm_ioremap_resource(dev, iomem);
2356 return PTR_ERR(base);
2358 return musb_init_controller(dev, irq, base);
2361 static int musb_remove(struct platform_device *pdev)
2363 struct device *dev = &pdev->dev;
2364 struct musb *musb = dev_to_musb(dev);
2365 unsigned long flags;
2367 /* this gets called on rmmod.
2368 * - Host mode: host may still be active
2369 * - Peripheral mode: peripheral is deactivated (or never-activated)
2370 * - OTG mode: both roles are deactivated (or never-activated)
2372 musb_exit_debugfs(musb);
2374 cancel_work_sync(&musb->irq_work);
2375 cancel_delayed_work_sync(&musb->finish_resume_work);
2376 cancel_delayed_work_sync(&musb->deassert_reset_work);
2377 pm_runtime_get_sync(musb->controller);
2378 musb_host_cleanup(musb);
2379 musb_gadget_cleanup(musb);
2380 spin_lock_irqsave(&musb->lock, flags);
2381 musb_platform_disable(musb);
2382 musb_generic_disable(musb);
2383 spin_unlock_irqrestore(&musb->lock, flags);
2384 musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
2385 pm_runtime_dont_use_autosuspend(musb->controller);
2386 pm_runtime_put_sync(musb->controller);
2387 pm_runtime_disable(musb->controller);
2388 musb_platform_exit(musb);
2389 musb_phy_callback = NULL;
2390 if (musb->dma_controller)
2391 musb_dma_controller_destroy(musb->dma_controller);
2392 usb_phy_shutdown(musb->xceiv);
2394 device_init_wakeup(dev, 0);
2400 static void musb_save_context(struct musb *musb)
2403 void __iomem *musb_base = musb->mregs;
2406 musb->context.frame = musb_readw(musb_base, MUSB_FRAME);
2407 musb->context.testmode = musb_readb(musb_base, MUSB_TESTMODE);
2408 musb->context.busctl = musb_read_ulpi_buscontrol(musb->mregs);
2409 musb->context.power = musb_readb(musb_base, MUSB_POWER);
2410 musb->context.intrusbe = musb_readb(musb_base, MUSB_INTRUSBE);
2411 musb->context.index = musb_readb(musb_base, MUSB_INDEX);
2412 musb->context.devctl = musb_readb(musb_base, MUSB_DEVCTL);
2414 for (i = 0; i < musb->config->num_eps; ++i) {
2415 struct musb_hw_ep *hw_ep;
2417 hw_ep = &musb->endpoints[i];
2425 musb_writeb(musb_base, MUSB_INDEX, i);
2426 musb->context.index_regs[i].txmaxp =
2427 musb_readw(epio, MUSB_TXMAXP);
2428 musb->context.index_regs[i].txcsr =
2429 musb_readw(epio, MUSB_TXCSR);
2430 musb->context.index_regs[i].rxmaxp =
2431 musb_readw(epio, MUSB_RXMAXP);
2432 musb->context.index_regs[i].rxcsr =
2433 musb_readw(epio, MUSB_RXCSR);
2435 if (musb->dyn_fifo) {
2436 musb->context.index_regs[i].txfifoadd =
2437 musb_read_txfifoadd(musb_base);
2438 musb->context.index_regs[i].rxfifoadd =
2439 musb_read_rxfifoadd(musb_base);
2440 musb->context.index_regs[i].txfifosz =
2441 musb_read_txfifosz(musb_base);
2442 musb->context.index_regs[i].rxfifosz =
2443 musb_read_rxfifosz(musb_base);
2446 musb->context.index_regs[i].txtype =
2447 musb_readb(epio, MUSB_TXTYPE);
2448 musb->context.index_regs[i].txinterval =
2449 musb_readb(epio, MUSB_TXINTERVAL);
2450 musb->context.index_regs[i].rxtype =
2451 musb_readb(epio, MUSB_RXTYPE);
2452 musb->context.index_regs[i].rxinterval =
2453 musb_readb(epio, MUSB_RXINTERVAL);
2455 musb->context.index_regs[i].txfunaddr =
2456 musb_read_txfunaddr(musb, i);
2457 musb->context.index_regs[i].txhubaddr =
2458 musb_read_txhubaddr(musb, i);
2459 musb->context.index_regs[i].txhubport =
2460 musb_read_txhubport(musb, i);
2462 musb->context.index_regs[i].rxfunaddr =
2463 musb_read_rxfunaddr(musb, i);
2464 musb->context.index_regs[i].rxhubaddr =
2465 musb_read_rxhubaddr(musb, i);
2466 musb->context.index_regs[i].rxhubport =
2467 musb_read_rxhubport(musb, i);
2471 static void musb_restore_context(struct musb *musb)
2474 void __iomem *musb_base = musb->mregs;
2478 musb_writew(musb_base, MUSB_FRAME, musb->context.frame);
2479 musb_writeb(musb_base, MUSB_TESTMODE, musb->context.testmode);
2480 musb_write_ulpi_buscontrol(musb->mregs, musb->context.busctl);
2482 /* Don't affect SUSPENDM/RESUME bits in POWER reg */
2483 power = musb_readb(musb_base, MUSB_POWER);
2484 power &= MUSB_POWER_SUSPENDM | MUSB_POWER_RESUME;
2485 musb->context.power &= ~(MUSB_POWER_SUSPENDM | MUSB_POWER_RESUME);
2486 power |= musb->context.power;
2487 musb_writeb(musb_base, MUSB_POWER, power);
2489 musb_writew(musb_base, MUSB_INTRTXE, musb->intrtxe);
2490 musb_writew(musb_base, MUSB_INTRRXE, musb->intrrxe);
2491 musb_writeb(musb_base, MUSB_INTRUSBE, musb->context.intrusbe);
2492 if (musb->context.devctl & MUSB_DEVCTL_SESSION)
2493 musb_writeb(musb_base, MUSB_DEVCTL, musb->context.devctl);
2495 for (i = 0; i < musb->config->num_eps; ++i) {
2496 struct musb_hw_ep *hw_ep;
2498 hw_ep = &musb->endpoints[i];
2506 musb_writeb(musb_base, MUSB_INDEX, i);
2507 musb_writew(epio, MUSB_TXMAXP,
2508 musb->context.index_regs[i].txmaxp);
2509 musb_writew(epio, MUSB_TXCSR,
2510 musb->context.index_regs[i].txcsr);
2511 musb_writew(epio, MUSB_RXMAXP,
2512 musb->context.index_regs[i].rxmaxp);
2513 musb_writew(epio, MUSB_RXCSR,
2514 musb->context.index_regs[i].rxcsr);
2516 if (musb->dyn_fifo) {
2517 musb_write_txfifosz(musb_base,
2518 musb->context.index_regs[i].txfifosz);
2519 musb_write_rxfifosz(musb_base,
2520 musb->context.index_regs[i].rxfifosz);
2521 musb_write_txfifoadd(musb_base,
2522 musb->context.index_regs[i].txfifoadd);
2523 musb_write_rxfifoadd(musb_base,
2524 musb->context.index_regs[i].rxfifoadd);
2527 musb_writeb(epio, MUSB_TXTYPE,
2528 musb->context.index_regs[i].txtype);
2529 musb_writeb(epio, MUSB_TXINTERVAL,
2530 musb->context.index_regs[i].txinterval);
2531 musb_writeb(epio, MUSB_RXTYPE,
2532 musb->context.index_regs[i].rxtype);
2533 musb_writeb(epio, MUSB_RXINTERVAL,
2535 musb->context.index_regs[i].rxinterval);
2536 musb_write_txfunaddr(musb, i,
2537 musb->context.index_regs[i].txfunaddr);
2538 musb_write_txhubaddr(musb, i,
2539 musb->context.index_regs[i].txhubaddr);
2540 musb_write_txhubport(musb, i,
2541 musb->context.index_regs[i].txhubport);
2543 musb_write_rxfunaddr(musb, i,
2544 musb->context.index_regs[i].rxfunaddr);
2545 musb_write_rxhubaddr(musb, i,
2546 musb->context.index_regs[i].rxhubaddr);
2547 musb_write_rxhubport(musb, i,
2548 musb->context.index_regs[i].rxhubport);
2550 musb_writeb(musb_base, MUSB_INDEX, musb->context.index);
2553 static int musb_suspend(struct device *dev)
2555 struct musb *musb = dev_to_musb(dev);
2556 unsigned long flags;
2558 musb_platform_disable(musb);
2559 musb_generic_disable(musb);
2561 spin_lock_irqsave(&musb->lock, flags);
2563 if (is_peripheral_active(musb)) {
2564 /* FIXME force disconnect unless we know USB will wake
2565 * the system up quickly enough to respond ...
2567 } else if (is_host_active(musb)) {
2568 /* we know all the children are suspended; sometimes
2569 * they will even be wakeup-enabled.
2573 musb_save_context(musb);
2575 spin_unlock_irqrestore(&musb->lock, flags);
2579 static int musb_resume(struct device *dev)
2581 struct musb *musb = dev_to_musb(dev);
2586 * For static cmos like DaVinci, register values were preserved
2587 * unless for some reason the whole soc powered down or the USB
2588 * module got reset through the PSC (vs just being disabled).
2590 * For the DSPS glue layer though, a full register restore has to
2591 * be done. As it shouldn't harm other platforms, we do it
2595 musb_restore_context(musb);
2597 devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
2598 mask = MUSB_DEVCTL_BDEVICE | MUSB_DEVCTL_FSDEV | MUSB_DEVCTL_LSDEV;
2599 if ((devctl & mask) != (musb->context.devctl & mask))
2600 musb->port1_status = 0;
2601 if (musb->need_finish_resume) {
2602 musb->need_finish_resume = 0;
2603 schedule_delayed_work(&musb->finish_resume_work,
2604 msecs_to_jiffies(USB_RESUME_TIMEOUT));
2608 * The USB HUB code expects the device to be in RPM_ACTIVE once it came
2611 pm_runtime_disable(dev);
2612 pm_runtime_set_active(dev);
2613 pm_runtime_enable(dev);
2620 static int musb_runtime_suspend(struct device *dev)
2622 struct musb *musb = dev_to_musb(dev);
2624 musb_save_context(musb);
2629 static int musb_runtime_resume(struct device *dev)
2631 struct musb *musb = dev_to_musb(dev);
2632 static int first = 1;
2635 * When pm_runtime_get_sync called for the first time in driver
2636 * init, some of the structure is still not initialized which is
2637 * used in restore function. But clock needs to be
2638 * enabled before any register access, so
2639 * pm_runtime_get_sync has to be called.
2640 * Also context restore without save does not make
2644 musb_restore_context(musb);
2647 if (musb->need_finish_resume) {
2648 musb->need_finish_resume = 0;
2649 schedule_delayed_work(&musb->finish_resume_work,
2650 msecs_to_jiffies(USB_RESUME_TIMEOUT));
2656 static const struct dev_pm_ops musb_dev_pm_ops = {
2657 .suspend = musb_suspend,
2658 .resume = musb_resume,
2659 .runtime_suspend = musb_runtime_suspend,
2660 .runtime_resume = musb_runtime_resume,
2663 #define MUSB_DEV_PM_OPS (&musb_dev_pm_ops)
2665 #define MUSB_DEV_PM_OPS NULL
2668 static struct platform_driver musb_driver = {
2670 .name = (char *)musb_driver_name,
2671 .bus = &platform_bus_type,
2672 .pm = MUSB_DEV_PM_OPS,
2674 .probe = musb_probe,
2675 .remove = musb_remove,
2678 module_platform_driver(musb_driver);