2 # Physical Layer USB driver configuration
4 menu "USB Physical Layer drivers"
10 tristate "USB 2.0 OTG FSM implementation"
15 Implements OTG Final State Machine as specified in On-The-Go
16 and Embedded Host Supplement to the USB Revision 2.0 Specification.
19 # USB Transceiver Drivers
22 tristate "AB8500 USB Transceiver Driver"
23 depends on AB8500_CORE
26 Enable this to support the USB OTG transceiver in AB8500 chip.
27 This transceiver supports high and full speed devices plus,
28 in host mode, low speed.
31 bool "Freescale USB OTG Transceiver Driver"
32 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
36 Enable this to support Freescale USB OTG transceiver.
39 tristate "Philips ISP1301 with OMAP OTG"
40 depends on I2C && ARCH_OMAP_OTG
44 If you say yes here you get support for the Philips ISP1301
45 USB-On-The-Go transceiver working with the OMAP OTG controller.
46 The ISP1301 is a full speed USB transceiver which is used in
47 products including H2, H3, and H4 development boards for Texas
48 Instruments OMAP processors.
50 This driver can also be built as a module. If so, the module
51 will be called phy-isp1301-omap.
53 config KEYSTONE_USB_PHY
54 tristate "Keystone USB PHY Driver"
55 depends on ARCH_KEYSTONE || COMPILE_TEST
58 Enable this to support Keystone USB phy. This driver provides
59 interface to interact with USB 2.0 and USB 3.0 PHY that is part
63 bool "Marvell USB 3.0 PHY controller Driver"
67 Enable this to support Marvell USB 3.0 phy controller for Marvell
71 tristate "NOP USB Transceiver Driver"
74 This driver is to be used by all the usb transceiver which are either
75 built-in with usb ip or which are autonomous and doesn't require any
76 phy programming such as ISP1x04 etc.
78 config AM335X_CONTROL_USB
82 tristate "AM335x USB PHY Driver"
83 depends on ARM || COMPILE_TEST
85 select AM335X_CONTROL_USB
88 This driver provides PHY support for that phy which part for the
94 Enable this to support Samsung USB phy helper driver for Samsung SoCs.
95 This driver provides common interface to interact, for Samsung USB 2.0 PHY
96 driver and later for Samsung USB 3.0 PHY driver.
98 config SAMSUNG_USB2PHY
99 tristate "Samsung USB 2.0 PHY controller Driver"
100 select SAMSUNG_USBPHY
103 Enable this to support Samsung USB 2.0 (High Speed) PHY controller
104 driver for Samsung SoCs.
106 config SAMSUNG_USB3PHY
107 tristate "Samsung USB 3.0 PHY controller Driver"
108 select SAMSUNG_USBPHY
111 Enable this to support Samsung USB 3.0 (Super Speed) phy controller
115 tristate "TWL6030 USB Transceiver Driver"
116 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
118 Enable this to support the USB OTG transceiver on TWL6030
119 family chips. This TWL6030 transceiver has the VBUS and ID GND
120 and OTG SRP events capabilities. For all other transceiver functionality
121 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
122 are hooked to this driver through platform_data structure.
123 The definition of internal PHY APIs are in the mach-omap2 layer.
126 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
130 Provides simple GPIO VBUS sensing for controllers with an
131 internal transceiver via the usb_phy interface, and
132 optionally control of a D+ pullup GPIO as well as a VBUS
133 current limit regulator.
136 tristate "OMAP USB OTG controller driver"
137 depends on ARCH_OMAP_OTG && EXTCON
139 Enable this to support some transceivers on OMAP1 platforms. OTG
140 controller is needed to switch between host and peripheral modes.
142 This driver can also be built as a module. If so, the module
143 will be called phy-omap-otg.
146 tristate "Tahvo USB transceiver driver"
147 depends on MFD_RETU && EXTCON
150 Enable this to support USB transceiver on Tahvo. This is used
151 at least on Nokia 770.
153 config TAHVO_USB_HOST_BY_DEFAULT
155 boolean "Device in USB host mode by default"
157 Say Y here, if you want the device to enter USB host mode
158 by default on bootup.
161 tristate "NXP ISP1301 USB transceiver support"
162 depends on USB || USB_GADGET
166 Say Y here to add support for the NXP ISP1301 USB transceiver driver.
167 This chip is typically used as USB transceiver for USB host, gadget
168 and OTG drivers (to be selected separately).
170 To compile this driver as a module, choose M here: the
171 module will be called phy-isp1301.
174 tristate "OTG support for Qualcomm on-chip USB controller"
175 depends on (USB || USB_GADGET) && ARCH_MSM
178 Enable this to support the USB OTG transceiver on MSM chips. It
179 handles PHY initialization, clock management, and workarounds
180 required after resetting the hardware and power management.
181 This driver is required even for peripheral only or host only
183 This driver is not supported on boards like trout which
187 tristate "Marvell USB OTG support"
188 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
192 Say Y here if you want to build Marvell USB OTG transciever
193 driver in kernel (including PXA and MMP series). This driver
194 implements role switch between EHCI host driver and gadget driver.
196 To compile this driver as a module, choose M here.
199 tristate "Freescale MXS USB PHY support"
200 depends on ARCH_MXC || ARCH_MXS
204 Enable this to support the Freescale MXS USB PHY.
206 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
209 tristate "Renesas R-Car USB PHY support"
210 depends on USB || USB_GADGET
213 Say Y here to add support for the Renesas R-Car USB common PHY driver.
214 This chip is typically used as USB PHY for USB host, gadget.
215 This driver supports R8A7778 and R8A7779.
217 To compile this driver as a module, choose M here: the
218 module will be called phy-rcar-usb.
220 config USB_RCAR_GEN2_PHY
221 tristate "Renesas R-Car Gen2 USB PHY support"
222 depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST
225 Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver.
226 It is typically used to control internal USB PHY for USBHS,
227 and to configure shared USB channels 0 and 2.
228 This driver supports R8A7790 and R8A7791.
230 To compile this driver as a module, choose M here: the
231 module will be called phy-rcar-gen2-usb.
234 bool "Generic ULPI Transceiver Driver"
237 Enable this to support ULPI connected USB OTG transceivers which
238 are likely found on embedded boards.
240 config USB_ULPI_VIEWPORT
244 Provides read/write operations to the ULPI phy register set for
245 controllers with a viewport register (e.g. Chipidea/ARC controllers).