include/configs/spc1920.h

   1 /*
   2  * (C) Copyright 2006
   3  * Markus Klotzbuecher, DENX Software Engineering, mk@denx.de
   4  *
   5  * Configuation settings for the SPC1920 board.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_SPC1920                  1       /* SPC1920 board */
  14 #define CONFIG_MPC885                   1       /* MPC885 CPU */
  15
  16 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  17
  18 #define CONFIG_8xx_CONS_SMC1            /* Console is on SMC1 */
  19 #undef  CONFIG_8xx_CONS_SMC2
  20 #undef  CONFIG_8xx_CONS_NONE
  21
  22 #define CONFIG_MII
  23 #define CONFIG_MII_INIT         1
  24 #undef CONFIG_ETHER_ON_FEC1
  25 #define CONFIG_ETHER_ON_FEC2
  26 #define FEC_ENET
  27 #define CONFIG_FEC2_PHY         1
  28
  29 #define CONFIG_BAUDRATE         19200
  30
  31 /* use PLD CLK4 instead of brg */
  32 #define CONFIG_SYS_SPC1920_SMC1_CLK4
  33
  34 #define CONFIG_8xx_OSCLK                10000000 /* 10 MHz oscillator on EXTCLK  */
  35 #define CONFIG_8xx_CPUCLK_DEFAULT       50000000
  36 #define CONFIG_SYS_8xx_CPUCLK_MIN               40000000
  37 #define CONFIG_SYS_8xx_CPUCLK_MAX               133000000
  38
  39 #define CONFIG_SYS_RESET_ADDRESS                0xC0000000
  40
  41 #define CONFIG_BOARD_EARLY_INIT_F
  42 #define CONFIG_LAST_STAGE_INIT
  43
  44 #if 0
  45 #define CONFIG_BOOTDELAY        -1      /* autoboot disabled            */
  46 #else
  47 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
  48 #endif
  49
  50 #define CONFIG_ENV_OVERWRITE
  51
  52 #define CONFIG_NFSBOOTCOMMAND                                                   \
  53     "dhcp;"                                                                     \
  54     "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath "                       \
  55     "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"              \
  56     "bootm"
  57
  58 #define CONFIG_BOOTCOMMAND                                                      \
  59     "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\
  60     "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;"              \
  61     "bootm fe080000"
  62
  63 #undef CONFIG_BOOTARGS
  64
  65 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  66 #define CONFIG_BZIP2     /* include support for bzip2 compressed images */
  67
  68
  69 /*
  70  * BOOTP options
  71  */
  72 #define CONFIG_BOOTP_BOOTFILESIZE
  73 #define CONFIG_BOOTP_BOOTPATH
  74 #define CONFIG_BOOTP_GATEWAY
  75 #define CONFIG_BOOTP_HOSTNAME
  76
  77
  78 /*
  79  * Command line configuration.
  80  */
  81 #include <config_cmd_default.h>
  82
  83 #define CONFIG_CMD_ASKENV
  84 #define CONFIG_CMD_DATE
  85 #define CONFIG_CMD_ECHO
  86 #define CONFIG_CMD_IMMAP
  87 #define CONFIG_CMD_JFFS2
  88 #define CONFIG_CMD_NET
  89 #define CONFIG_CMD_PING
  90 #define CONFIG_CMD_DHCP
  91 #define CONFIG_CMD_I2C
  92 #define CONFIG_CMD_MII
  93
  94 /*
  95  * Miscellaneous configurable options
  96  */
  97 #define CONFIG_SYS_LONGHELP                             /* undef to save memory         */
  98 #define CONFIG_SYS_PROMPT               "=>"            /* Monitor Command Prompt       */
  99 #define CONFIG_SYS_HUSH_PARSER
 100
 101 #if defined(CONFIG_CMD_KGDB)
 102 #define CONFIG_SYS_CBSIZE               1024            /* Console I/O Buffer Size      */
 103 #else
 104 #define CONFIG_SYS_CBSIZE               256             /* Console I/O Buffer Size      */
 105 #endif
 106
 107 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size     */
 108 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
 109 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 110
 111 #define CONFIG_SYS_LOAD_ADDR            0x00100000
 112
 113 #define CONFIG_SYS_HZ                   1000    /* decrementer freq: 1 ms ticks */
 114
 115 #define CONFIG_SYS_BAUDRATE_TABLE       { 2400, 4800, 9600, 19200 }
 116
 117 /*
 118  * Low Level Configuration Settings
 119  * (address mappings, register initial values, etc.)
 120  * You should know what you are doing if you make changes here.
 121  */
 122
 123 /*-----------------------------------------------------------------------
 124  * Internal Memory Mapped Register
 125  */
 126 #define CONFIG_SYS_IMMR         0xF0000000
 127
 128 /*-----------------------------------------------------------------------
 129  * Definitions for initial stack pointer and data area (in DPRAM)
 130  */
 131 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 132 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 133 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 134 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 135
 136 /*-----------------------------------------------------------------------
 137  * Start addresses for the final memory configuration
 138  * (Set up by the startup code)
 139  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 140  */
 141 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 142 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 143
 144 /*
 145  * For booting Linux, the board info and command line data
 146  * have to be in the first 8 MB of memory, since this is
 147  * the maximum mapped by the Linux kernel during initialization.
 148  */
 149 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 150
 151 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 152 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 KB for monitor   */
 153
 154 #ifdef CONFIG_BZIP2
 155 #define CONFIG_SYS_MALLOC_LEN           (2500 << 10)    /* Reserve ~2.5 MB for malloc() */
 156 #else
 157 #define CONFIG_SYS_MALLOC_LEN           (384 << 10)     /* Reserve 384 kB for malloc()  */
 158 #endif /* CONFIG_BZIP2 */
 159
 160 #define CONFIG_SYS_ALLOC_DPRAM          1       /* use allocation routines      */
 161
 162 /*
 163  * Flash
 164  */
 165 /*-----------------------------------------------------------------------
 166  * Flash organisation
 167  */
 168 #define CONFIG_SYS_FLASH_BASE          0xFE000000
 169 #define CONFIG_SYS_FLASH_CFI                           /* The flash is CFI compatible  */
 170 #define CONFIG_FLASH_CFI_DRIVER                    /* Use common CFI driver        */
 171 #define CONFIG_SYS_MAX_FLASH_BANKS     1               /* Max number of flash banks    */
 172 #define CONFIG_SYS_MAX_FLASH_SECT      128             /* Max num of sects on one chip */
 173
 174 /* Environment is in flash */
 175 #define CONFIG_ENV_IS_IN_FLASH
 176 #define CONFIG_ENV_SECT_SIZE       0x40000         /* We use one complete sector   */
 177 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 178
 179 #define CONFIG_ENV_OVERWRITE
 180
 181 /*-----------------------------------------------------------------------
 182  * Cache Configuration
 183  */
 184 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 185 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 186
 187 #ifdef CONFIG_CMD_DATE
 188 # define CONFIG_RTC_DS3231
 189 # define CONFIG_SYS_I2C_RTC_ADDR      0x68
 190 #endif
 191
 192 /*-----------------------------------------------------------------------
 193  * I2C configuration
 194  */
 195 #if defined(CONFIG_CMD_I2C)
 196 /* enable I2C and select the hardware/software driver */
 197 #undef CONFIG_HARD_I2C                 /* I2C with hardware support    */
 198 #define CONFIG_SOFT_I2C                1       /* I2C bit-banged               */
 199
 200 #define CONFIG_SYS_I2C_SPEED          93000   /* 93 kHz is supposed to work   */
 201 #define CONFIG_SYS_I2C_SLAVE          0xFE
 202
 203 #ifdef CONFIG_SOFT_I2C
 204 /*
 205  * Software (bit-bang) I2C driver configuration
 206  */
 207 #define PB_SCL         0x00000020      /* PB 26 */
 208 #define PB_SDA         0x00000010      /* PB 27 */
 209
 210 #define I2C_INIT       (immr->im_cpm.cp_pbdir |=  PB_SCL)
 211 #define I2C_ACTIVE     (immr->im_cpm.cp_pbdir |=  PB_SDA)
 212 #define I2C_TRISTATE   (immr->im_cpm.cp_pbdir &= ~PB_SDA)
 213 #define I2C_READ       ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 214 #define I2C_SDA(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 215                        else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 216 #define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 217                        else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 218 #define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
 219 #endif /* CONFIG_SOFT_I2C */
 220 #endif
 221
 222 /*-----------------------------------------------------------------------
 223  * SYPCR - System Protection Control                            11-9
 224  * SYPCR can only be written once after reset!
 225  *-----------------------------------------------------------------------
 226  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 227  */
 228 #if defined(CONFIG_WATCHDOG)
 229 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 230                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 231 #else
 232 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 233 #endif
 234
 235 /*-----------------------------------------------------------------------
 236  * SIUMCR - SIU Module Configuration                            11-6
 237  *-----------------------------------------------------------------------
 238  * PCMCIA config., multi-function pin tri-state
 239  */
 240 #define CONFIG_SYS_SIUMCR      (SIUMCR_FRC)
 241
 242 /*-----------------------------------------------------------------------
 243  * TBSCR - Time Base Status and Control                         11-26
 244  *-----------------------------------------------------------------------
 245  * Clear Reference Interrupt Status, Timebase freezing enabled
 246  */
 247 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
 248
 249 /*-----------------------------------------------------------------------
 250  * PISCR - Periodic Interrupt Status and Control                11-31
 251  *-----------------------------------------------------------------------
 252  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 253  */
 254 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 255
 256 /*-----------------------------------------------------------------------
 257  * SCCR - System Clock and reset Control Register               15-27
 258  *-----------------------------------------------------------------------
 259  * Set clock output, timebase and RTC source and divider,
 260  * power management and some other internal clocks
 261  */
 262 #define SCCR_MASK       SCCR_EBDF11
 263 /* #define CONFIG_SYS_SCCR      SCCR_TBS */
 264 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 265                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 266                          SCCR_DFALCD00)
 267
 268 /*-----------------------------------------------------------------------
 269  * DER - Debug Enable Register
 270  *-----------------------------------------------------------------------
 271  * Set to zero to prevent the processor from entering debug mode
 272  */
 273 #define CONFIG_SYS_DER           0
 274
 275
 276 /* Because of the way the 860 starts up and assigns CS0 the entire
 277  * address space, we have to set the memory controller differently.
 278  * Normally, you write the option register first, and then enable the
 279  * chip select by writing the base register.  For CS0, you must write
 280  * the base register first, followed by the option register.
 281  */
 282
 283
 284 /*
 285  * Init Memory Controller:
 286  */
 287
 288 /* BR0 and OR0 (FLASH) */
 289 #define FLASH_BASE0_PRELIM      CONFIG_SYS_FLASH_BASE   /* FLASH bank #0 */
 290
 291
 292 /* used to re-map FLASH both when starting from SRAM or FLASH:
 293  * restrict access enough to keep SRAM working (if any)
 294  * but not too much to meddle with FLASH accesses
 295  */
 296 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 297 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 298
 299 /*
 300  * FLASH timing:
 301  */
 302 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 303                                  OR_SCY_6_CLK | OR_EHTR | OR_BI)
 304
 305 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 306 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 307 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 308
 309
 310 /*
 311  * SDRAM CS1 UPMB
 312  */
 313 #define CONFIG_SYS_SDRAM_BASE   0x00000000
 314 #define CONFIG_SYS_SDRAM_BASE_PRELIM CONFIG_SYS_SDRAM_BASE
 315 #define SDRAM_MAX_SIZE  0x4000000 /* max 64 MB */
 316
 317 #define CONFIG_SYS_PRELIM_OR1_AM        0xF0000000
 318 /* #define CONFIG_SYS_OR1_TIMING  OR_CSNT_SAM/\*  | OR_G5LS /\\* *\\/ *\/ */
 319 #define SDRAM_TIMING    OR_SCY_0_CLK    /* SDRAM-Timing */
 320
 321 #define CONFIG_SYS_OR1_PRELIM   (CONFIG_SYS_PRELIM_OR1_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING)
 322 #define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V)
 323
 324 /* #define CONFIG_SYS_OR1_FINAL   ((CONFIG_SYS_OR1_AM & OR_AM_MSK) | CONFIG_SYS_OR1_TIMING) */
 325 /* #define CONFIG_SYS_BR1_FINAL   ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V) */
 326
 327 #define CONFIG_SYS_PTB_PER_CLK  ((4096 * 16 * 1000) / (4 * 64))
 328 #define CONFIG_SYS_PTA_PER_CLK 195
 329 #define CONFIG_SYS_MBMR_PTB     195
 330 #define CONFIG_SYS_MPTPR        MPTPR_PTP_DIV16
 331 #define CONFIG_SYS_MAR          0x88
 332
 333 #define CONFIG_SYS_MBMR_8COL  ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \
 334                         MBMR_AMB_TYPE_0 | \
 335                         MBMR_G0CLB_A10 | \
 336                         MBMR_DSB_1_CYCL | \
 337                         MBMR_RLFB_1X | \
 338                         MBMR_WLFB_1X | \
 339                         MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
 340
 341 #define CONFIG_SYS_MBMR_9COL  ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \
 342                         MBMR_AMB_TYPE_1 | \
 343                         MBMR_G0CLB_A10 | \
 344                         MBMR_DSB_1_CYCL | \
 345                         MBMR_RLFB_1X | \
 346                         MBMR_WLFB_1X | \
 347                         MBMR_TLFB_4X) /* 0x04804114 */ /* 0x10802114 */
 348
 349
 350 /*
 351  * DSP Host Port Interface CS3
 352  */
 353 #define CONFIG_SYS_SPC1920_HPI_BASE   0x90000000
 354 #define CONFIG_SYS_PRELIM_OR3_AM      0xF8000000
 355
 356 #define CONFIG_SYS_OR3         (CONFIG_SYS_PRELIM_OR3_AM | \
 357                                        OR_G5LS | \
 358                                        OR_SCY_0_CLK | \
 359                                        OR_BI)
 360
 361 #define CONFIG_SYS_BR3 ((CONFIG_SYS_SPC1920_HPI_BASE & BR_BA_MSK) | \
 362                                                BR_MS_UPMA | \
 363                                                BR_PS_16 | \
 364                                                BR_V)
 365
 366 #define CONFIG_SYS_MAMR (MAMR_GPL_A4DIS | \
 367                 MAMR_RLFA_5X | \
 368                 MAMR_WLFA_5X)
 369
 370 #define CONFIG_SPC1920_HPI_TEST
 371
 372 #ifdef CONFIG_SPC1920_HPI_TEST
 373 #define HPI_REG(x)             (*((volatile u16 *) (CONFIG_SYS_SPC1920_HPI_BASE + x)))
 374 #define HPI_HPIC_1             HPI_REG(0)
 375 #define HPI_HPIC_2             HPI_REG(2)
 376 #define HPI_HPIA_1             HPI_REG(0x2000008)
 377 #define HPI_HPIA_2             HPI_REG(0x2000008 + 2)
 378 #define HPI_HPID_INC_1         HPI_REG(0x1000004)
 379 #define HPI_HPID_INC_2         HPI_REG(0x1000004 + 2)
 380 #define HPI_HPID_NOINC_1       HPI_REG(0x300000c)
 381 #define HPI_HPID_NOINC_2       HPI_REG(0x300000c + 2)
 382 #endif /* CONFIG_SPC1920_HPI_TEST */
 383
 384 /*
 385  * Ramtron FM18L08 FRAM 32KB on CS4
 386  */
 387 #define CONFIG_SYS_SPC1920_FRAM_BASE    0x80100000
 388 #define CONFIG_SYS_PRELIM_OR4_AM        0xffff8000
 389 #define CONFIG_SYS_OR4          (CONFIG_SYS_PRELIM_OR4_AM | \
 390                                         OR_ACS_DIV2 | \
 391                                         OR_BI | \
 392                                         OR_SCY_4_CLK | \
 393                                         OR_TRLX)
 394
 395 #define CONFIG_SYS_BR4 ((CONFIG_SYS_SPC1920_FRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
 396
 397 /*
 398  * PLD CS5
 399  */
 400 #define CONFIG_SYS_SPC1920_PLD_BASE     0x80000000
 401 #define CONFIG_SYS_PRELIM_OR5_AM        0xffff8000
 402
 403 #define CONFIG_SYS_OR5_PRELIM           (CONFIG_SYS_PRELIM_OR5_AM | \
 404                                         OR_CSNT_SAM | \
 405                                         OR_ACS_DIV1 | \
 406                                         OR_BI | \
 407                                         OR_SCY_0_CLK | \
 408                                         OR_TRLX)
 409
 410 #define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SPC1920_PLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
 411
 412 #endif  /* __CONFIG_H */