4 * linux/include/linux/ide.h
6 * Copyright (C) 1994-2002 Linus Torvalds & authors
9 #include <linux/init.h>
10 #include <linux/ioport.h>
11 #include <linux/ata.h>
12 #include <linux/blkdev.h>
13 #include <linux/proc_fs.h>
14 #include <linux/interrupt.h>
15 #include <linux/bitops.h>
16 #include <linux/bio.h>
17 #include <linux/device.h>
18 #include <linux/pci.h>
19 #include <linux/completion.h>
21 #ifdef CONFIG_BLK_DEV_IDEACPI
22 #include <acpi/acpi.h>
24 #include <asm/byteorder.h>
25 #include <asm/system.h>
27 #include <asm/mutex.h>
29 #if defined(CONFIG_CRIS) || defined(CONFIG_FRV)
30 # define SUPPORT_VLB_SYNC 0
32 # define SUPPORT_VLB_SYNC 1
36 * Used to indicate "no IRQ", should be a value that cannot be an IRQ
40 #define IDE_NO_IRQ (-1)
42 typedef unsigned char byte; /* used everywhere */
45 * Probably not wise to fiddle with these
47 #define ERROR_MAX 8 /* Max read/write errors per sector */
48 #define ERROR_RESET 3 /* Reset controller every 4th retry */
49 #define ERROR_RECAL 1 /* Recalibrate every 2nd retry */
51 #define HWIF(drive) ((ide_hwif_t *)((drive)->hwif))
52 #define HWGROUP(drive) ((ide_hwgroup_t *)(HWIF(drive)->hwgroup))
55 * Definitions for accessing IDE controller registers
57 #define IDE_NR_PORTS (10)
60 unsigned long data_addr;
63 unsigned long error_addr; /* read: error */
64 unsigned long feature_addr; /* write: feature */
67 unsigned long nsect_addr;
68 unsigned long lbal_addr;
69 unsigned long lbam_addr;
70 unsigned long lbah_addr;
72 unsigned long device_addr;
75 unsigned long status_addr; /* read: status */
76 unsigned long command_addr; /* write: command */
79 unsigned long ctl_addr;
81 unsigned long irq_addr;
84 #define OK_STAT(stat,good,bad) (((stat)&((good)|(bad)))==(good))
86 #define BAD_R_STAT (ATA_BUSY | ATA_ERR)
87 #define BAD_W_STAT (BAD_R_STAT | ATA_DF)
88 #define BAD_STAT (BAD_R_STAT | ATA_DRQ)
89 #define DRIVE_READY (ATA_DRDY | ATA_DSC)
91 #define BAD_CRC (ATA_ABORTED | ATA_ICRC)
93 #define SATA_NR_PORTS (3) /* 16 possible ?? */
95 #define SATA_STATUS_OFFSET (0)
96 #define SATA_ERROR_OFFSET (1)
97 #define SATA_CONTROL_OFFSET (2)
100 * Our Physical Region Descriptor (PRD) table should be large enough
101 * to handle the biggest I/O request we are likely to see. Since requests
102 * can have no more than 256 sectors, and since the typical blocksize is
103 * two or more sectors, we could get by with a limit of 128 entries here for
104 * the usual worst case. Most requests seem to include some contiguous blocks,
105 * further reducing the number of table entries required.
107 * The driver reverts to PIO mode for individual requests that exceed
108 * this limit (possible with 512 byte blocksizes, eg. MSDOS f/s), so handling
109 * 100% of all crazy scenarios here is not necessary.
111 * As it turns out though, we must allocate a full 4KB page for this,
112 * so the two PRD tables (ide0 & ide1) will each get half of that,
113 * allowing each to have about 256 entries (8 bytes each) from this.
116 #define PRD_ENTRIES 256
119 * Some more useful definitions
121 #define PARTN_BITS 6 /* number of minor dev bits for partitions */
122 #define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */
123 #define SECTOR_SIZE 512
125 #define IDE_LARGE_SEEK(b1,b2,t) (((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
128 * Timeouts for various operations:
131 /* spec allows up to 20ms */
132 WAIT_DRQ = HZ / 10, /* 100ms */
133 /* some laptops are very slow */
134 WAIT_READY = 5 * HZ, /* 5s */
135 /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
136 WAIT_PIDENTIFY = 10 * HZ, /* 10s */
137 /* worst case when spinning up */
138 WAIT_WORSTCASE = 30 * HZ, /* 30s */
139 /* maximum wait for an IRQ to happen */
140 WAIT_CMD = 10 * HZ, /* 10s */
141 /* Some drives require a longer IRQ timeout. */
142 WAIT_FLOPPY_CMD = 50 * HZ, /* 50s */
144 * Some drives (for example, Seagate STT3401A Travan) require a very
145 * long timeout, because they don't return an interrupt or clear their
146 * BSY bit until after the command completes (even retension commands).
148 WAIT_TAPE_CMD = 900 * HZ, /* 900s */
149 /* minimum sleep time */
150 WAIT_MIN_SLEEP = HZ / 50, /* 20ms */
154 * Op codes for special requests to be handled by ide_special_rq().
155 * Values should be in the range of 0x20 to 0x3f.
157 #define REQ_DRIVE_RESET 0x20
158 #define REQ_DEVSET_EXEC 0x21
161 * Check for an interrupt and acknowledge the interrupt status
164 typedef int (ide_ack_intr_t)(struct hwif_s *);
167 * hwif_chipset_t is used to keep track of the specific hardware
168 * chipset used by each IDE interface, if known.
170 enum { ide_unknown, ide_generic, ide_pci,
171 ide_cmd640, ide_dtc2278, ide_ali14xx,
172 ide_qd65xx, ide_umc8672, ide_ht6560b,
173 ide_rz1000, ide_trm290,
174 ide_cmd646, ide_cy82c693, ide_4drives,
176 ide_au1xxx, ide_palm3710
179 typedef u8 hwif_chipset_t;
182 * Structure to hold all information about the location of this port
184 typedef struct hw_regs_s {
186 struct ide_io_ports io_ports;
187 unsigned long io_ports_array[IDE_NR_PORTS];
190 int irq; /* our irq number */
191 ide_ack_intr_t *ack_intr; /* acknowledge interrupt */
192 hwif_chipset_t chipset;
193 struct device *dev, *parent;
194 unsigned long config;
197 void ide_init_port_data(struct hwif_s *, unsigned int);
198 void ide_init_port_hw(struct hwif_s *, hw_regs_t *);
200 static inline void ide_std_init_ports(hw_regs_t *hw,
201 unsigned long io_addr,
202 unsigned long ctl_addr)
206 for (i = 0; i <= 7; i++)
207 hw->io_ports_array[i] = io_addr++;
209 hw->io_ports.ctl_addr = ctl_addr;
212 /* for IDE PCI controllers in legacy mode, temporary */
213 static inline int __ide_default_irq(unsigned long base)
217 case 0x1f0: return isa_irq_to_vector(14);
218 case 0x170: return isa_irq_to_vector(15);
220 case 0x1f0: return 14;
221 case 0x170: return 15;
227 #if defined(CONFIG_ARM) || defined(CONFIG_FRV) || defined(CONFIG_M68K) || \
228 defined(CONFIG_MIPS) || defined(CONFIG_MN10300) || defined(CONFIG_PARISC) \
229 || defined(CONFIG_PPC) || defined(CONFIG_SPARC) || defined(CONFIG_SPARC64)
232 #include <asm-generic/ide_iops.h>
237 /* Currently only m68k, apus and m8xx need it */
238 #ifndef IDE_ARCH_ACK_INTR
239 # define ide_ack_intr(hwif) (1)
242 /* Currently only Atari needs it */
243 #ifndef IDE_ARCH_LOCK
244 # define ide_release_lock() do {} while (0)
245 # define ide_get_lock(hdlr, data) do {} while (0)
246 #endif /* IDE_ARCH_LOCK */
249 * Now for the data we need to maintain per-drive: ide_drive_t
252 #define ide_scsi 0x21
253 #define ide_disk 0x20
254 #define ide_optical 0x7
255 #define ide_cdrom 0x5
257 #define ide_floppy 0x0
260 * Special Driver Flags
262 * set_geometry : respecify drive geometry
263 * recalibrate : seek to cyl 0
264 * set_multmode : set multmode count
270 unsigned set_geometry : 1;
271 unsigned recalibrate : 1;
272 unsigned set_multmode : 1;
273 unsigned reserved : 5;
278 * Status returned from various ide_ functions
281 ide_stopped, /* no drive operation was started */
282 ide_started, /* a drive operation was started, handler was set */
286 IDE_TFLAG_LBA48 = (1 << 0),
287 IDE_TFLAG_FLAGGED = (1 << 2),
288 IDE_TFLAG_OUT_DATA = (1 << 3),
289 IDE_TFLAG_OUT_HOB_FEATURE = (1 << 4),
290 IDE_TFLAG_OUT_HOB_NSECT = (1 << 5),
291 IDE_TFLAG_OUT_HOB_LBAL = (1 << 6),
292 IDE_TFLAG_OUT_HOB_LBAM = (1 << 7),
293 IDE_TFLAG_OUT_HOB_LBAH = (1 << 8),
294 IDE_TFLAG_OUT_HOB = IDE_TFLAG_OUT_HOB_FEATURE |
295 IDE_TFLAG_OUT_HOB_NSECT |
296 IDE_TFLAG_OUT_HOB_LBAL |
297 IDE_TFLAG_OUT_HOB_LBAM |
298 IDE_TFLAG_OUT_HOB_LBAH,
299 IDE_TFLAG_OUT_FEATURE = (1 << 9),
300 IDE_TFLAG_OUT_NSECT = (1 << 10),
301 IDE_TFLAG_OUT_LBAL = (1 << 11),
302 IDE_TFLAG_OUT_LBAM = (1 << 12),
303 IDE_TFLAG_OUT_LBAH = (1 << 13),
304 IDE_TFLAG_OUT_TF = IDE_TFLAG_OUT_FEATURE |
305 IDE_TFLAG_OUT_NSECT |
309 IDE_TFLAG_OUT_DEVICE = (1 << 14),
310 IDE_TFLAG_WRITE = (1 << 15),
311 IDE_TFLAG_FLAGGED_SET_IN_FLAGS = (1 << 16),
312 IDE_TFLAG_IN_DATA = (1 << 17),
313 IDE_TFLAG_CUSTOM_HANDLER = (1 << 18),
314 IDE_TFLAG_DMA_PIO_FALLBACK = (1 << 19),
315 IDE_TFLAG_IN_HOB_FEATURE = (1 << 20),
316 IDE_TFLAG_IN_HOB_NSECT = (1 << 21),
317 IDE_TFLAG_IN_HOB_LBAL = (1 << 22),
318 IDE_TFLAG_IN_HOB_LBAM = (1 << 23),
319 IDE_TFLAG_IN_HOB_LBAH = (1 << 24),
320 IDE_TFLAG_IN_HOB_LBA = IDE_TFLAG_IN_HOB_LBAL |
321 IDE_TFLAG_IN_HOB_LBAM |
322 IDE_TFLAG_IN_HOB_LBAH,
323 IDE_TFLAG_IN_HOB = IDE_TFLAG_IN_HOB_FEATURE |
324 IDE_TFLAG_IN_HOB_NSECT |
325 IDE_TFLAG_IN_HOB_LBA,
326 IDE_TFLAG_IN_FEATURE = (1 << 1),
327 IDE_TFLAG_IN_NSECT = (1 << 25),
328 IDE_TFLAG_IN_LBAL = (1 << 26),
329 IDE_TFLAG_IN_LBAM = (1 << 27),
330 IDE_TFLAG_IN_LBAH = (1 << 28),
331 IDE_TFLAG_IN_LBA = IDE_TFLAG_IN_LBAL |
334 IDE_TFLAG_IN_TF = IDE_TFLAG_IN_NSECT |
336 IDE_TFLAG_IN_DEVICE = (1 << 29),
337 IDE_TFLAG_HOB = IDE_TFLAG_OUT_HOB |
339 IDE_TFLAG_TF = IDE_TFLAG_OUT_TF |
341 IDE_TFLAG_DEVICE = IDE_TFLAG_OUT_DEVICE |
343 /* force 16-bit I/O operations */
344 IDE_TFLAG_IO_16BIT = (1 << 30),
345 /* ide_task_t was allocated using kmalloc() */
346 IDE_TFLAG_DYN = (1 << 31),
349 struct ide_taskfile {
350 u8 hob_data; /* 0: high data byte (for TASKFILE IOCTL) */
352 u8 hob_feature; /* 1-5: additional data to support LBA48 */
358 u8 data; /* 6: low data byte (for TASKFILE IOCTL) */
361 u8 error; /* read: error */
362 u8 feature; /* write: feature */
365 u8 nsect; /* 8: number of sectors */
366 u8 lbal; /* 9: LBA low */
367 u8 lbam; /* 10: LBA mid */
368 u8 lbah; /* 11: LBA high */
370 u8 device; /* 12: device select */
373 u8 status; /* read: status */
374 u8 command; /* write: command */
378 typedef struct ide_task_s {
380 struct ide_taskfile tf;
385 struct request *rq; /* copy of request */
386 void *special; /* valid_t generally */
389 /* ATAPI packet command flags */
391 /* set when an error is considered normal - no retry (ide-tape) */
392 PC_FLAG_ABORT = (1 << 0),
393 PC_FLAG_SUPPRESS_ERROR = (1 << 1),
394 PC_FLAG_WAIT_FOR_DSC = (1 << 2),
395 PC_FLAG_DMA_OK = (1 << 3),
396 PC_FLAG_DMA_IN_PROGRESS = (1 << 4),
397 PC_FLAG_DMA_ERROR = (1 << 5),
398 PC_FLAG_WRITING = (1 << 6),
399 /* command timed out */
400 PC_FLAG_TIMEDOUT = (1 << 7),
404 * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
405 * This is used for several packet commands (not for READ/WRITE commands).
407 #define IDE_PC_BUFFER_SIZE 256
409 struct ide_atapi_pc {
410 /* actual packet bytes */
412 /* incremented on each retry */
416 /* bytes to transfer */
418 /* bytes actually transferred */
423 /* current buffer position */
426 /* missing/available data on the current buffer */
429 /* the corresponding request */
435 * those are more or less driver-specific and some of them are subject
436 * to change/removal later.
438 u8 pc_buf[IDE_PC_BUFFER_SIZE];
441 struct idetape_bh *bh;
444 /* idescsi only for now */
445 struct scatterlist *sg;
448 struct scsi_cmnd *scsi_cmd;
449 void (*done) (struct scsi_cmnd *);
451 unsigned long timeout;
457 #ifdef CONFIG_BLK_DEV_IDEACPI
458 struct ide_acpi_drive_link;
459 struct ide_acpi_hwif_link;
462 /* ATAPI device flags */
464 IDE_AFLAG_DRQ_INTERRUPT = (1 << 0),
465 IDE_AFLAG_MEDIA_CHANGED = (1 << 1),
466 /* Drive cannot lock the door. */
467 IDE_AFLAG_NO_DOORLOCK = (1 << 2),
470 /* Drive cannot eject the disc. */
471 IDE_AFLAG_NO_EJECT = (1 << 3),
472 /* Drive is a pre ATAPI 1.2 drive. */
473 IDE_AFLAG_PRE_ATAPI12 = (1 << 4),
474 /* TOC addresses are in BCD. */
475 IDE_AFLAG_TOCADDR_AS_BCD = (1 << 5),
476 /* TOC track numbers are in BCD. */
477 IDE_AFLAG_TOCTRACKS_AS_BCD = (1 << 6),
479 * Drive does not provide data in multiples of SECTOR_SIZE
480 * when more than one interrupt is needed.
482 IDE_AFLAG_LIMIT_NFRAMES = (1 << 7),
483 /* Seeking in progress. */
484 IDE_AFLAG_SEEKING = (1 << 8),
485 /* Saved TOC information is current. */
486 IDE_AFLAG_TOC_VALID = (1 << 9),
487 /* We think that the drive door is locked. */
488 IDE_AFLAG_DOOR_LOCKED = (1 << 10),
489 /* SET_CD_SPEED command is unsupported. */
490 IDE_AFLAG_NO_SPEED_SELECT = (1 << 11),
491 IDE_AFLAG_VERTOS_300_SSD = (1 << 12),
492 IDE_AFLAG_VERTOS_600_ESD = (1 << 13),
493 IDE_AFLAG_SANYO_3CD = (1 << 14),
494 IDE_AFLAG_FULL_CAPS_PAGE = (1 << 15),
495 IDE_AFLAG_PLAY_AUDIO_OK = (1 << 16),
496 IDE_AFLAG_LE_SPEED_FIELDS = (1 << 17),
499 /* Format in progress */
500 IDE_AFLAG_FORMAT_IN_PROGRESS = (1 << 18),
501 /* Avoid commands not supported in Clik drive */
502 IDE_AFLAG_CLIK_DRIVE = (1 << 19),
503 /* Requires BH algorithm for packets */
504 IDE_AFLAG_ZIP_DRIVE = (1 << 20),
506 IDE_AFLAG_WP = (1 << 21),
507 /* Supports format progress report */
508 IDE_AFLAG_SRFP = (1 << 22),
511 IDE_AFLAG_IGNORE_DSC = (1 << 23),
512 /* 0 When the tape position is unknown */
513 IDE_AFLAG_ADDRESS_VALID = (1 << 24),
514 /* Device already opened */
515 IDE_AFLAG_BUSY = (1 << 25),
516 /* Attempt to auto-detect the current user block size */
517 IDE_AFLAG_DETECT_BS = (1 << 26),
518 /* Currently on a filemark */
519 IDE_AFLAG_FILEMARK = (1 << 27),
520 /* 0 = no tape is loaded, so we don't rewind after ejecting */
521 IDE_AFLAG_MEDIUM_PRESENT = (1 << 28),
523 IDE_AFLAG_NO_AUTOCLOSE = (1 << 29),
528 /* restore settings after device reset */
529 IDE_DFLAG_KEEP_SETTINGS = (1 << 0),
530 /* device is using DMA for read/write */
531 IDE_DFLAG_USING_DMA = (1 << 1),
532 /* okay to unmask other IRQs */
533 IDE_DFLAG_UNMASK = (1 << 2),
534 /* don't attempt flushes */
535 IDE_DFLAG_NOFLUSH = (1 << 3),
537 IDE_DFLAG_DSC_OVERLAP = (1 << 4),
538 /* give potential excess bandwidth */
539 IDE_DFLAG_NICE1 = (1 << 5),
540 /* device is physically present */
541 IDE_DFLAG_PRESENT = (1 << 6),
542 /* device ejected hint */
543 IDE_DFLAG_DEAD = (1 << 7),
544 /* id read from device (synthetic if not set) */
545 IDE_DFLAG_ID_READ = (1 << 8),
546 IDE_DFLAG_NOPROBE = (1 << 9),
547 /* need to do check_media_change() */
548 IDE_DFLAG_REMOVABLE = (1 << 10),
549 /* needed for removable devices */
550 IDE_DFLAG_ATTACH = (1 << 11),
551 IDE_DFLAG_FORCED_GEOM = (1 << 12),
552 /* disallow setting unmask bit */
553 IDE_DFLAG_NO_UNMASK = (1 << 13),
554 /* disallow enabling 32-bit I/O */
555 IDE_DFLAG_NO_IO_32BIT = (1 << 14),
556 /* for removable only: door lock/unlock works */
557 IDE_DFLAG_DOORLOCKING = (1 << 15),
559 IDE_DFLAG_NODMA = (1 << 16),
560 /* powermanagment told us not to do anything, so sleep nicely */
561 IDE_DFLAG_BLOCKED = (1 << 17),
562 /* ide-scsi emulation */
563 IDE_DFLAG_SCSI = (1 << 18),
564 /* sleeping & sleep field valid */
565 IDE_DFLAG_SLEEPING = (1 << 19),
566 IDE_DFLAG_POST_RESET = (1 << 20),
567 IDE_DFLAG_UDMA33_WARNED = (1 << 21),
568 IDE_DFLAG_LBA48 = (1 << 22),
569 /* status of write cache */
570 IDE_DFLAG_WCACHE = (1 << 23),
571 /* used for ignoring ATA_DF */
572 IDE_DFLAG_NOWERR = (1 << 24),
573 /* retrying in PIO */
574 IDE_DFLAG_DMA_PIO_RETRY = (1 << 25),
575 IDE_DFLAG_LBA = (1 << 26),
579 char name[4]; /* drive name, such as "hda" */
580 char driver_req[10]; /* requests specific driver */
582 struct request_queue *queue; /* request queue */
584 struct request *rq; /* current request */
585 struct ide_drive_s *next; /* circular list of hwgroup drives */
586 void *driver_data; /* extra driver data */
587 u16 *id; /* identification info */
588 #ifdef CONFIG_IDE_PROC_FS
589 struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
590 const struct ide_proc_devset *settings; /* /proc/ide/ drive settings */
592 struct hwif_s *hwif; /* actually (ide_hwif_t *) */
594 unsigned long dev_flags;
596 unsigned long sleep; /* sleep until this time */
597 unsigned long service_start; /* time we started last request */
598 unsigned long service_time; /* service time of last request */
599 unsigned long timeout; /* max time to wait for irq */
601 special_t special; /* special action flags */
603 u8 select; /* basic drive/head select reg value */
604 u8 retry_pio; /* retrying dma capable host in pio */
605 u8 waiting_for_dma; /* dma currently in progress */
607 u8 quirk_list; /* considered quirky, set for a specific host */
608 u8 init_speed; /* transfer rate set at boot */
609 u8 current_speed; /* current transfer rate set */
610 u8 desired_speed; /* desired transfer rate set */
611 u8 dn; /* now wide spread use */
612 u8 acoustic; /* acoustic management */
613 u8 media; /* disk, cdrom, tape, floppy, ... */
614 u8 ready_stat; /* min status value for drive ready */
615 u8 mult_count; /* current multiple sector setting */
616 u8 mult_req; /* requested multiple sector setting */
617 u8 io_32bit; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
618 u8 bad_wstat; /* used for ignoring ATA_DF */
619 u8 head; /* "real" number of heads */
620 u8 sect; /* "real" sectors per track */
621 u8 bios_head; /* BIOS/fdisk/LILO number of heads */
622 u8 bios_sect; /* BIOS/fdisk/LILO sectors per track */
624 /* delay this long before sending packet command */
627 unsigned int bios_cyl; /* BIOS/fdisk/LILO number of cyls */
628 unsigned int cyl; /* "real" number of cyls */
629 unsigned int drive_data; /* used by set_pio_mode/selectproc */
630 unsigned int failures; /* current failure count */
631 unsigned int max_failures; /* maximum allowed failure count */
632 u64 probed_capacity;/* initial reported media capacity (ide-cd only currently) */
634 u64 capacity64; /* total number of sectors */
636 int lun; /* logical unit */
637 int crc_count; /* crc counter to reduce drive speed */
639 unsigned long debug_mask; /* debugging levels switch */
641 #ifdef CONFIG_BLK_DEV_IDEACPI
642 struct ide_acpi_drive_link *acpidata;
644 struct list_head list;
645 struct device gendev;
646 struct completion gendev_rel_comp; /* to deal with device release() */
648 /* current packet command */
649 struct ide_atapi_pc *pc;
651 /* callback for packet commands */
652 void (*pc_callback)(struct ide_drive_s *, int);
654 void (*pc_update_buffers)(struct ide_drive_s *, struct ide_atapi_pc *);
655 int (*pc_io_buffers)(struct ide_drive_s *, struct ide_atapi_pc *,
658 unsigned long atapi_flags;
660 struct ide_atapi_pc request_sense_pc;
661 struct request request_sense_rq;
664 typedef struct ide_drive_s ide_drive_t;
666 #define to_ide_device(dev) container_of(dev, ide_drive_t, gendev)
668 #define to_ide_drv(obj, cont_type) \
669 container_of(obj, struct cont_type, kref)
671 #define ide_drv_g(disk, cont_type) \
672 container_of((disk)->private_data, struct cont_type, driver)
674 struct ide_port_info;
677 void (*exec_command)(struct hwif_s *, u8);
678 u8 (*read_status)(struct hwif_s *);
679 u8 (*read_altstatus)(struct hwif_s *);
680 u8 (*read_sff_dma_status)(struct hwif_s *);
682 void (*set_irq)(struct hwif_s *, int);
684 void (*tf_load)(ide_drive_t *, struct ide_task_s *);
685 void (*tf_read)(ide_drive_t *, struct ide_task_s *);
687 void (*input_data)(ide_drive_t *, struct request *, void *,
689 void (*output_data)(ide_drive_t *, struct request *, void *,
693 extern const struct ide_tp_ops default_tp_ops;
696 * struct ide_port_ops - IDE port operations
698 * @init_dev: host specific initialization of a device
699 * @set_pio_mode: routine to program host for PIO mode
700 * @set_dma_mode: routine to program host for DMA mode
701 * @selectproc: tweaks hardware to select drive
702 * @reset_poll: chipset polling based on hba specifics
703 * @pre_reset: chipset specific changes to default for device-hba resets
704 * @resetproc: routine to reset controller after a disk reset
705 * @maskproc: special host masking for drive selection
706 * @quirkproc: check host's drive quirk list
707 * @clear_irq: clear IRQ
709 * @mdma_filter: filter MDMA modes
710 * @udma_filter: filter UDMA modes
712 * @cable_detect: detect cable type
714 struct ide_port_ops {
715 void (*init_dev)(ide_drive_t *);
716 void (*set_pio_mode)(ide_drive_t *, const u8);
717 void (*set_dma_mode)(ide_drive_t *, const u8);
718 void (*selectproc)(ide_drive_t *);
719 int (*reset_poll)(ide_drive_t *);
720 void (*pre_reset)(ide_drive_t *);
721 void (*resetproc)(ide_drive_t *);
722 void (*maskproc)(ide_drive_t *, int);
723 void (*quirkproc)(ide_drive_t *);
724 void (*clear_irq)(ide_drive_t *);
726 u8 (*mdma_filter)(ide_drive_t *);
727 u8 (*udma_filter)(ide_drive_t *);
729 u8 (*cable_detect)(struct hwif_s *);
733 void (*dma_host_set)(struct ide_drive_s *, int);
734 int (*dma_setup)(struct ide_drive_s *);
735 void (*dma_exec_cmd)(struct ide_drive_s *, u8);
736 void (*dma_start)(struct ide_drive_s *);
737 int (*dma_end)(struct ide_drive_s *);
738 int (*dma_test_irq)(struct ide_drive_s *);
739 void (*dma_lost_irq)(struct ide_drive_s *);
740 void (*dma_timeout)(struct ide_drive_s *);
745 typedef struct hwif_s {
746 struct hwif_s *next; /* for linked-list in ide_hwgroup_t */
747 struct hwif_s *mate; /* other hwif from same PCI chip */
748 struct hwgroup_s *hwgroup; /* actually (ide_hwgroup_t *) */
749 struct proc_dir_entry *proc; /* /proc/ide/ directory entry */
751 struct ide_host *host;
753 char name[6]; /* name of interface, eg. "ide0" */
755 struct ide_io_ports io_ports;
757 unsigned long sata_scr[SATA_NR_PORTS];
759 ide_drive_t drives[MAX_DRIVES]; /* drive info */
761 u8 major; /* our major number */
762 u8 index; /* 0 for ide0; 1 for ide1; ... */
763 u8 channel; /* for dual-port chips: 0=primary, 1=secondary */
773 u8 cbl; /* cable type */
775 hwif_chipset_t chipset; /* sub-module for tuning.. */
779 ide_ack_intr_t *ack_intr;
781 void (*rw_disk)(ide_drive_t *, struct request *);
783 const struct ide_tp_ops *tp_ops;
784 const struct ide_port_ops *port_ops;
785 const struct ide_dma_ops *dma_ops;
787 /* dma physical region descriptor table (cpu view) */
788 unsigned int *dmatable_cpu;
789 /* dma physical region descriptor table (dma view) */
790 dma_addr_t dmatable_dma;
791 /* Scatter-gather list used to build the above */
792 struct scatterlist *sg_table;
793 int sg_max_nents; /* Maximum number of entries in it */
794 int sg_nents; /* Current number of entries in it */
795 int sg_dma_direction; /* dma transfer direction */
797 /* data phase of the active command (currently only valid for PIO/DMA) */
800 struct ide_task_s task; /* current command */
804 struct scatterlist *cursg;
805 unsigned int cursg_ofs;
807 int rqsize; /* max sectors per request */
808 int irq; /* our irq number */
810 unsigned long dma_base; /* base addr for dma ports */
812 unsigned long config_data; /* for use by chipset-specific code */
813 unsigned long select_data; /* for use by chipset-specific code */
815 unsigned long extra_base; /* extra addr for dma ports */
816 unsigned extra_ports; /* number of extra dma ports */
818 unsigned present : 1; /* this interface exists */
819 unsigned serialized : 1; /* serialized all channel operation */
820 unsigned sharing_irq: 1; /* 1 = sharing irq with another hwif */
821 unsigned sg_mapped : 1; /* sg_table and sg_nents are ready */
823 struct device gendev;
824 struct device *portdev;
826 struct completion gendev_rel_comp; /* To deal with device release() */
828 void *hwif_data; /* extra hwif data */
830 #ifdef CONFIG_BLK_DEV_IDEACPI
831 struct ide_acpi_hwif_link *acpidata;
833 } ____cacheline_internodealigned_in_smp ide_hwif_t;
835 #define MAX_HOST_PORTS 4
838 ide_hwif_t *ports[MAX_HOST_PORTS];
839 unsigned int n_ports;
840 struct device *dev[2];
841 unsigned int (*init_chipset)(struct pci_dev *);
842 unsigned long host_flags;
847 * internal ide interrupt handler type
849 typedef ide_startstop_t (ide_handler_t)(ide_drive_t *);
850 typedef int (ide_expiry_t)(ide_drive_t *);
852 /* used by ide-cd, ide-floppy, etc. */
853 typedef void (xfer_func_t)(ide_drive_t *, struct request *rq, void *, unsigned);
855 typedef struct hwgroup_s {
856 /* irq handler, if active */
857 ide_startstop_t (*handler)(ide_drive_t *);
859 /* BOOL: protects all fields below */
861 /* BOOL: wake us up on timer expiry */
862 unsigned int sleeping : 1;
863 /* BOOL: polling active & poll_timeout field valid */
864 unsigned int polling : 1;
868 /* ptr to current hwif in linked-list */
871 /* current request */
875 struct timer_list timer;
876 /* timeout value during long polls */
877 unsigned long poll_timeout;
878 /* queried upon timeouts */
879 int (*expiry)(ide_drive_t *);
885 typedef struct ide_driver_s ide_driver_t;
887 extern struct mutex ide_setting_mtx;
890 * configurable drive settings
893 #define DS_SYNC (1 << 0)
896 int (*get)(ide_drive_t *);
897 int (*set)(ide_drive_t *, int);
901 #define __DEVSET(_flags, _get, _set) { \
907 #define ide_devset_get(name, field) \
908 static int get_##name(ide_drive_t *drive) \
910 return drive->field; \
913 #define ide_devset_set(name, field) \
914 static int set_##name(ide_drive_t *drive, int arg) \
916 drive->field = arg; \
920 #define ide_devset_get_flag(name, flag) \
921 static int get_##name(ide_drive_t *drive) \
923 return !!(drive->dev_flags & flag); \
926 #define ide_devset_set_flag(name, flag) \
927 static int set_##name(ide_drive_t *drive, int arg) \
930 drive->dev_flags |= flag; \
932 drive->dev_flags &= ~flag; \
936 #define __IDE_DEVSET(_name, _flags, _get, _set) \
937 const struct ide_devset ide_devset_##_name = \
938 __DEVSET(_flags, _get, _set)
940 #define IDE_DEVSET(_name, _flags, _get, _set) \
941 static __IDE_DEVSET(_name, _flags, _get, _set)
943 #define ide_devset_rw(_name, _func) \
944 IDE_DEVSET(_name, 0, get_##_func, set_##_func)
946 #define ide_devset_w(_name, _func) \
947 IDE_DEVSET(_name, 0, NULL, set_##_func)
949 #define ide_ext_devset_rw(_name, _func) \
950 __IDE_DEVSET(_name, 0, get_##_func, set_##_func)
952 #define ide_ext_devset_rw_sync(_name, _func) \
953 __IDE_DEVSET(_name, DS_SYNC, get_##_func, set_##_func)
955 #define ide_decl_devset(_name) \
956 extern const struct ide_devset ide_devset_##_name
958 ide_decl_devset(io_32bit);
959 ide_decl_devset(keepsettings);
960 ide_decl_devset(pio_mode);
961 ide_decl_devset(unmaskirq);
962 ide_decl_devset(using_dma);
964 #ifdef CONFIG_IDE_PROC_FS
966 * /proc/ide interface
969 #define ide_devset_rw_field(_name, _field) \
970 ide_devset_get(_name, _field); \
971 ide_devset_set(_name, _field); \
972 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
974 #define ide_devset_rw_flag(_name, _field) \
975 ide_devset_get_flag(_name, _field); \
976 ide_devset_set_flag(_name, _field); \
977 IDE_DEVSET(_name, DS_SYNC, get_##_name, set_##_name)
979 struct ide_proc_devset {
981 const struct ide_devset *setting;
983 int (*mulf)(ide_drive_t *);
984 int (*divf)(ide_drive_t *);
987 #define __IDE_PROC_DEVSET(_name, _min, _max, _mulf, _divf) { \
988 .name = __stringify(_name), \
989 .setting = &ide_devset_##_name, \
996 #define IDE_PROC_DEVSET(_name, _min, _max) \
997 __IDE_PROC_DEVSET(_name, _min, _max, NULL, NULL)
1002 read_proc_t *read_proc;
1003 write_proc_t *write_proc;
1006 void proc_ide_create(void);
1007 void proc_ide_destroy(void);
1008 void ide_proc_register_port(ide_hwif_t *);
1009 void ide_proc_port_register_devices(ide_hwif_t *);
1010 void ide_proc_unregister_device(ide_drive_t *);
1011 void ide_proc_unregister_port(ide_hwif_t *);
1012 void ide_proc_register_driver(ide_drive_t *, ide_driver_t *);
1013 void ide_proc_unregister_driver(ide_drive_t *, ide_driver_t *);
1015 read_proc_t proc_ide_read_capacity;
1016 read_proc_t proc_ide_read_geometry;
1019 * Standard exit stuff:
1021 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) \
1024 if (len < count) { \
1030 *start = page + off; \
1034 static inline void proc_ide_create(void) { ; }
1035 static inline void proc_ide_destroy(void) { ; }
1036 static inline void ide_proc_register_port(ide_hwif_t *hwif) { ; }
1037 static inline void ide_proc_port_register_devices(ide_hwif_t *hwif) { ; }
1038 static inline void ide_proc_unregister_device(ide_drive_t *drive) { ; }
1039 static inline void ide_proc_unregister_port(ide_hwif_t *hwif) { ; }
1040 static inline void ide_proc_register_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
1041 static inline void ide_proc_unregister_driver(ide_drive_t *drive, ide_driver_t *driver) { ; }
1042 #define PROC_IDE_READ_RETURN(page,start,off,count,eof,len) return 0;
1046 /* enter/exit functions */
1047 IDE_DBG_FUNC = (1 << 0),
1048 /* sense key/asc handling */
1049 IDE_DBG_SENSE = (1 << 1),
1050 /* packet commands handling */
1051 IDE_DBG_PC = (1 << 2),
1052 /* request handling */
1053 IDE_DBG_RQ = (1 << 3),
1054 /* driver probing/setup */
1055 IDE_DBG_PROBE = (1 << 4),
1058 /* DRV_NAME has to be defined in the driver before using the macro below */
1059 #define __ide_debug_log(lvl, fmt, args...) \
1061 if (unlikely(drive->debug_mask & lvl)) \
1062 printk(KERN_INFO DRV_NAME ": " fmt, ## args); \
1066 * Power Management state machine (rq->pm->pm_step).
1068 * For each step, the core calls ide_start_power_step() first.
1070 * - ide_stopped : In this case, the core calls us back again unless
1071 * step have been set to ide_power_state_completed.
1072 * - ide_started : In this case, the channel is left busy until an
1073 * async event (interrupt) occurs.
1074 * Typically, ide_start_power_step() will issue a taskfile request with
1077 * Upon reception of the interrupt, the core will call ide_complete_power_step()
1078 * with the error code if any. This routine should update the step value
1079 * and return. It should not start a new request. The core will call
1080 * ide_start_power_step() for the new step value, unless step have been
1081 * set to IDE_PM_COMPLETED.
1084 IDE_PM_START_SUSPEND,
1085 IDE_PM_FLUSH_CACHE = IDE_PM_START_SUSPEND,
1088 IDE_PM_START_RESUME,
1089 IDE_PM_RESTORE_PIO = IDE_PM_START_RESUME,
1097 * Subdrivers support.
1099 * The gendriver.owner field should be set to the module owner of this driver.
1100 * The gendriver.name field should be set to the name of this driver
1102 struct ide_driver_s {
1103 const char *version;
1104 ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
1105 int (*end_request)(ide_drive_t *, int, int);
1106 ide_startstop_t (*error)(ide_drive_t *, struct request *rq, u8, u8);
1107 struct device_driver gen_driver;
1108 int (*probe)(ide_drive_t *);
1109 void (*remove)(ide_drive_t *);
1110 void (*resume)(ide_drive_t *);
1111 void (*shutdown)(ide_drive_t *);
1112 #ifdef CONFIG_IDE_PROC_FS
1113 ide_proc_entry_t *proc;
1114 const struct ide_proc_devset *settings;
1118 #define to_ide_driver(drv) container_of(drv, ide_driver_t, gen_driver)
1120 int ide_device_get(ide_drive_t *);
1121 void ide_device_put(ide_drive_t *);
1123 struct ide_ioctl_devset {
1124 unsigned int get_ioctl;
1125 unsigned int set_ioctl;
1126 const struct ide_devset *setting;
1129 int ide_setting_ioctl(ide_drive_t *, struct block_device *, unsigned int,
1130 unsigned long, const struct ide_ioctl_devset *);
1132 int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *,
1133 unsigned, unsigned long);
1135 extern int ide_vlb_clk;
1136 extern int ide_pci_clk;
1138 extern int ide_end_request (ide_drive_t *drive, int uptodate, int nrsecs);
1139 int ide_end_dequeued_request(ide_drive_t *drive, struct request *rq,
1140 int uptodate, int nr_sectors);
1142 extern void ide_set_handler (ide_drive_t *drive, ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry);
1144 void ide_execute_command(ide_drive_t *, u8, ide_handler_t *, unsigned int,
1147 void ide_execute_pkt_cmd(ide_drive_t *);
1149 void ide_pad_transfer(ide_drive_t *, int, int);
1151 ide_startstop_t __ide_error(ide_drive_t *, struct request *, u8, u8);
1153 ide_startstop_t ide_error (ide_drive_t *drive, const char *msg, byte stat);
1155 void ide_fix_driveid(u16 *);
1157 extern void ide_fixstring(u8 *, const int, const int);
1159 int ide_busy_sleep(ide_hwif_t *, unsigned long, int);
1161 int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
1163 extern ide_startstop_t ide_do_reset (ide_drive_t *);
1165 extern int ide_devset_execute(ide_drive_t *drive,
1166 const struct ide_devset *setting, int arg);
1168 extern void ide_do_drive_cmd(ide_drive_t *, struct request *);
1170 extern void ide_end_drive_cmd(ide_drive_t *, u8, u8);
1172 void ide_tf_dump(const char *, struct ide_taskfile *);
1174 void ide_exec_command(ide_hwif_t *, u8);
1175 u8 ide_read_status(ide_hwif_t *);
1176 u8 ide_read_altstatus(ide_hwif_t *);
1177 u8 ide_read_sff_dma_status(ide_hwif_t *);
1179 void ide_set_irq(ide_hwif_t *, int);
1181 void ide_tf_load(ide_drive_t *, ide_task_t *);
1182 void ide_tf_read(ide_drive_t *, ide_task_t *);
1184 void ide_input_data(ide_drive_t *, struct request *, void *, unsigned int);
1185 void ide_output_data(ide_drive_t *, struct request *, void *, unsigned int);
1187 int ide_io_buffers(ide_drive_t *, struct ide_atapi_pc *, unsigned int, int);
1189 extern void SELECT_DRIVE(ide_drive_t *);
1190 void SELECT_MASK(ide_drive_t *, int);
1192 u8 ide_read_error(ide_drive_t *);
1193 void ide_read_bcount_and_ireason(ide_drive_t *, u16 *, u8 *);
1195 extern int drive_is_ready(ide_drive_t *);
1197 void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);
1199 int ide_check_atapi_device(ide_drive_t *, const char *);
1201 void ide_init_pc(struct ide_atapi_pc *);
1204 * Special requests for ide-tape block device strategy routine.
1206 * In order to service a character device command, we add special requests to
1207 * the tail of our block device request queue and wait for their completion.
1210 REQ_IDETAPE_PC1 = (1 << 0), /* packet command (first stage) */
1211 REQ_IDETAPE_PC2 = (1 << 1), /* packet command (second stage) */
1212 REQ_IDETAPE_READ = (1 << 2),
1213 REQ_IDETAPE_WRITE = (1 << 3),
1216 int ide_queue_pc_tail(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *);
1218 int ide_do_test_unit_ready(ide_drive_t *, struct gendisk *);
1219 int ide_do_start_stop(ide_drive_t *, struct gendisk *, int);
1220 int ide_set_media_lock(ide_drive_t *, struct gendisk *, int);
1221 void ide_create_request_sense_cmd(ide_drive_t *, struct ide_atapi_pc *);
1222 void ide_retry_pc(ide_drive_t *, struct gendisk *);
1224 static inline unsigned long ide_scsi_get_timeout(struct ide_atapi_pc *pc)
1226 return max_t(unsigned long, WAIT_CMD, pc->timeout - jiffies);
1229 int ide_scsi_expiry(ide_drive_t *);
1231 ide_startstop_t ide_issue_pc(ide_drive_t *, unsigned int, ide_expiry_t *);
1233 ide_startstop_t do_rw_taskfile(ide_drive_t *, ide_task_t *);
1235 void task_end_request(ide_drive_t *, struct request *, u8);
1237 int ide_raw_taskfile(ide_drive_t *, ide_task_t *, u8 *, u16);
1238 int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
1240 int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
1242 extern int ide_driveid_update(ide_drive_t *);
1243 extern int ide_config_drive_speed(ide_drive_t *, u8);
1244 extern u8 eighty_ninty_three (ide_drive_t *);
1245 extern int taskfile_lib_get_identify(ide_drive_t *drive, u8 *);
1247 extern int ide_wait_not_busy(ide_hwif_t *hwif, unsigned long timeout);
1249 extern void ide_stall_queue(ide_drive_t *drive, unsigned long timeout);
1251 extern void ide_timer_expiry(unsigned long);
1252 extern irqreturn_t ide_intr(int irq, void *dev_id);
1253 extern void do_ide_request(struct request_queue *);
1255 void ide_init_disk(struct gendisk *, ide_drive_t *);
1257 #ifdef CONFIG_IDEPCI_PCIBUS_ORDER
1258 extern int __ide_pci_register_driver(struct pci_driver *driver, struct module *owner, const char *mod_name);
1259 #define ide_pci_register_driver(d) __ide_pci_register_driver(d, THIS_MODULE, KBUILD_MODNAME)
1261 #define ide_pci_register_driver(d) pci_register_driver(d)
1264 void ide_pci_setup_ports(struct pci_dev *, const struct ide_port_info *, int,
1265 hw_regs_t *, hw_regs_t **);
1266 void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
1268 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
1269 int ide_pci_set_master(struct pci_dev *, const char *);
1270 unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
1271 int ide_pci_check_simplex(ide_hwif_t *, const struct ide_port_info *);
1272 int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
1274 static inline int ide_hwif_setup_dma(ide_hwif_t *hwif,
1275 const struct ide_port_info *d)
1281 typedef struct ide_pci_enablebit_s {
1282 u8 reg; /* byte pci reg holding the enable-bit */
1283 u8 mask; /* mask to isolate the enable-bit */
1284 u8 val; /* value of masked reg when "enabled" */
1285 } ide_pci_enablebit_t;
1288 /* Uses ISA control ports not PCI ones. */
1289 IDE_HFLAG_ISA_PORTS = (1 << 0),
1290 /* single port device */
1291 IDE_HFLAG_SINGLE = (1 << 1),
1292 /* don't use legacy PIO blacklist */
1293 IDE_HFLAG_PIO_NO_BLACKLIST = (1 << 2),
1294 /* set for the second port of QD65xx */
1295 IDE_HFLAG_QD_2ND_PORT = (1 << 3),
1296 /* use PIO8/9 for prefetch off/on */
1297 IDE_HFLAG_ABUSE_PREFETCH = (1 << 4),
1298 /* use PIO6/7 for fast-devsel off/on */
1299 IDE_HFLAG_ABUSE_FAST_DEVSEL = (1 << 5),
1300 /* use 100-102 and 200-202 PIO values to set DMA modes */
1301 IDE_HFLAG_ABUSE_DMA_MODES = (1 << 6),
1303 * keep DMA setting when programming PIO mode, may be used only
1304 * for hosts which have separate PIO and DMA timings (ie. PMAC)
1306 IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
1307 /* program host for the transfer mode after programming device */
1308 IDE_HFLAG_POST_SET_MODE = (1 << 8),
1309 /* don't program host/device for the transfer mode ("smart" hosts) */
1310 IDE_HFLAG_NO_SET_MODE = (1 << 9),
1311 /* trust BIOS for programming chipset/device for DMA */
1312 IDE_HFLAG_TRUST_BIOS_FOR_DMA = (1 << 10),
1313 /* host is CS5510/CS5520 */
1314 IDE_HFLAG_CS5520 = (1 << 11),
1315 /* ATAPI DMA is unsupported */
1316 IDE_HFLAG_NO_ATAPI_DMA = (1 << 12),
1317 /* set if host is a "non-bootable" controller */
1318 IDE_HFLAG_NON_BOOTABLE = (1 << 13),
1319 /* host doesn't support DMA */
1320 IDE_HFLAG_NO_DMA = (1 << 14),
1321 /* check if host is PCI IDE device before allowing DMA */
1322 IDE_HFLAG_NO_AUTODMA = (1 << 15),
1323 /* host uses MMIO */
1324 IDE_HFLAG_MMIO = (1 << 16),
1326 IDE_HFLAG_NO_LBA48 = (1 << 17),
1328 IDE_HFLAG_NO_LBA48_DMA = (1 << 18),
1329 /* data FIFO is cleared by an error */
1330 IDE_HFLAG_ERROR_STOPS_FIFO = (1 << 19),
1331 /* serialize ports */
1332 IDE_HFLAG_SERIALIZE = (1 << 20),
1333 /* use legacy IRQs */
1334 IDE_HFLAG_LEGACY_IRQS = (1 << 21),
1335 /* force use of legacy IRQs */
1336 IDE_HFLAG_FORCE_LEGACY_IRQS = (1 << 22),
1337 /* limit LBA48 requests to 256 sectors */
1338 IDE_HFLAG_RQSIZE_256 = (1 << 23),
1339 /* use 32-bit I/O ops */
1340 IDE_HFLAG_IO_32BIT = (1 << 24),
1342 IDE_HFLAG_UNMASK_IRQS = (1 << 25),
1343 /* serialize ports if DMA is possible (for sl82c105) */
1344 IDE_HFLAG_SERIALIZE_DMA = (1 << 27),
1345 /* force host out of "simplex" mode */
1346 IDE_HFLAG_CLEAR_SIMPLEX = (1 << 28),
1347 /* DSC overlap is unsupported */
1348 IDE_HFLAG_NO_DSC = (1 << 29),
1349 /* never use 32-bit I/O ops */
1350 IDE_HFLAG_NO_IO_32BIT = (1 << 30),
1351 /* never unmask IRQs */
1352 IDE_HFLAG_NO_UNMASK_IRQS = (1 << 31),
1355 #ifdef CONFIG_BLK_DEV_OFFBOARD
1356 # define IDE_HFLAG_OFF_BOARD 0
1358 # define IDE_HFLAG_OFF_BOARD IDE_HFLAG_NON_BOOTABLE
1361 struct ide_port_info {
1363 unsigned int (*init_chipset)(struct pci_dev *);
1364 void (*init_iops)(ide_hwif_t *);
1365 void (*init_hwif)(ide_hwif_t *);
1366 int (*init_dma)(ide_hwif_t *,
1367 const struct ide_port_info *);
1369 const struct ide_tp_ops *tp_ops;
1370 const struct ide_port_ops *port_ops;
1371 const struct ide_dma_ops *dma_ops;
1373 ide_pci_enablebit_t enablebits[2];
1374 hwif_chipset_t chipset;
1382 int ide_pci_init_one(struct pci_dev *, const struct ide_port_info *, void *);
1383 int ide_pci_init_two(struct pci_dev *, struct pci_dev *,
1384 const struct ide_port_info *, void *);
1385 void ide_pci_remove(struct pci_dev *);
1388 int ide_pci_suspend(struct pci_dev *, pm_message_t);
1389 int ide_pci_resume(struct pci_dev *);
1391 #define ide_pci_suspend NULL
1392 #define ide_pci_resume NULL
1395 void ide_map_sg(ide_drive_t *, struct request *);
1396 void ide_init_sg_cmd(ide_drive_t *, struct request *);
1398 #define BAD_DMA_DRIVE 0
1399 #define GOOD_DMA_DRIVE 1
1401 struct drive_list_entry {
1402 const char *id_model;
1403 const char *id_firmware;
1406 int ide_in_drive_list(u16 *, const struct drive_list_entry *);
1408 #ifdef CONFIG_BLK_DEV_IDEDMA
1409 int __ide_dma_bad_drive(ide_drive_t *);
1410 int ide_id_dma_bug(ide_drive_t *);
1412 u8 ide_find_dma_mode(ide_drive_t *, u8);
1414 static inline u8 ide_max_dma_mode(ide_drive_t *drive)
1416 return ide_find_dma_mode(drive, XFER_UDMA_6);
1419 void ide_dma_off_quietly(ide_drive_t *);
1420 void ide_dma_off(ide_drive_t *);
1421 void ide_dma_on(ide_drive_t *);
1422 int ide_set_dma(ide_drive_t *);
1423 void ide_check_dma_crc(ide_drive_t *);
1424 ide_startstop_t ide_dma_intr(ide_drive_t *);
1426 int ide_build_sglist(ide_drive_t *, struct request *);
1427 void ide_destroy_dmatable(ide_drive_t *);
1429 #ifdef CONFIG_BLK_DEV_IDEDMA_SFF
1430 extern int ide_build_dmatable(ide_drive_t *, struct request *);
1431 int ide_allocate_dma_engine(ide_hwif_t *);
1432 void ide_release_dma_engine(ide_hwif_t *);
1434 void ide_dma_host_set(ide_drive_t *, int);
1435 extern int ide_dma_setup(ide_drive_t *);
1436 void ide_dma_exec_cmd(ide_drive_t *, u8);
1437 extern void ide_dma_start(ide_drive_t *);
1438 int ide_dma_end(ide_drive_t *);
1439 int ide_dma_test_irq(ide_drive_t *);
1440 extern void ide_dma_lost_irq(ide_drive_t *);
1441 extern void ide_dma_timeout(ide_drive_t *);
1442 extern const struct ide_dma_ops sff_dma_ops;
1443 #endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
1446 static inline int ide_id_dma_bug(ide_drive_t *drive) { return 0; }
1447 static inline u8 ide_find_dma_mode(ide_drive_t *drive, u8 speed) { return 0; }
1448 static inline u8 ide_max_dma_mode(ide_drive_t *drive) { return 0; }
1449 static inline void ide_dma_off_quietly(ide_drive_t *drive) { ; }
1450 static inline void ide_dma_off(ide_drive_t *drive) { ; }
1451 static inline void ide_dma_on(ide_drive_t *drive) { ; }
1452 static inline void ide_dma_verbose(ide_drive_t *drive) { ; }
1453 static inline int ide_set_dma(ide_drive_t *drive) { return 1; }
1454 static inline void ide_check_dma_crc(ide_drive_t *drive) { ; }
1455 #endif /* CONFIG_BLK_DEV_IDEDMA */
1457 #ifndef CONFIG_BLK_DEV_IDEDMA_SFF
1458 static inline void ide_release_dma_engine(ide_hwif_t *hwif) { ; }
1461 #ifdef CONFIG_BLK_DEV_IDEACPI
1462 extern int ide_acpi_exec_tfs(ide_drive_t *drive);
1463 extern void ide_acpi_get_timing(ide_hwif_t *hwif);
1464 extern void ide_acpi_push_timing(ide_hwif_t *hwif);
1465 extern void ide_acpi_init(ide_hwif_t *hwif);
1466 void ide_acpi_port_init_devices(ide_hwif_t *);
1467 extern void ide_acpi_set_state(ide_hwif_t *hwif, int on);
1469 static inline int ide_acpi_exec_tfs(ide_drive_t *drive) { return 0; }
1470 static inline void ide_acpi_get_timing(ide_hwif_t *hwif) { ; }
1471 static inline void ide_acpi_push_timing(ide_hwif_t *hwif) { ; }
1472 static inline void ide_acpi_init(ide_hwif_t *hwif) { ; }
1473 static inline void ide_acpi_port_init_devices(ide_hwif_t *hwif) { ; }
1474 static inline void ide_acpi_set_state(ide_hwif_t *hwif, int on) {}
1477 void ide_remove_port_from_hwgroup(ide_hwif_t *);
1478 void ide_unregister(ide_hwif_t *);
1480 void ide_register_region(struct gendisk *);
1481 void ide_unregister_region(struct gendisk *);
1483 void ide_undecoded_slave(ide_drive_t *);
1485 void ide_port_apply_params(ide_hwif_t *);
1487 struct ide_host *ide_host_alloc(const struct ide_port_info *, hw_regs_t **);
1488 void ide_host_free(struct ide_host *);
1489 int ide_host_register(struct ide_host *, const struct ide_port_info *,
1491 int ide_host_add(const struct ide_port_info *, hw_regs_t **,
1492 struct ide_host **);
1493 void ide_host_remove(struct ide_host *);
1494 int ide_legacy_device_add(const struct ide_port_info *, unsigned long);
1495 void ide_port_unregister_devices(ide_hwif_t *);
1496 void ide_port_scan(ide_hwif_t *);
1498 static inline void *ide_get_hwifdata (ide_hwif_t * hwif)
1500 return hwif->hwif_data;
1503 static inline void ide_set_hwifdata (ide_hwif_t * hwif, void *data)
1505 hwif->hwif_data = data;
1508 const char *ide_xfer_verbose(u8 mode);
1509 extern void ide_toggle_bounce(ide_drive_t *drive, int on);
1510 extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
1512 u64 ide_get_lba_addr(struct ide_taskfile *, int);
1513 u8 ide_dump_status(ide_drive_t *, const char *, u8);
1518 u16 act8b; /* t2 for 8-bit io */
1519 u16 rec8b; /* t2i for 8-bit io */
1520 u16 cyc8b; /* t0 for 8-bit io */
1521 u16 active; /* t2 or tD */
1522 u16 recover; /* t2i or tK */
1524 u16 udma; /* t2CYCTYP/2 */
1528 IDE_TIMING_SETUP = (1 << 0),
1529 IDE_TIMING_ACT8B = (1 << 1),
1530 IDE_TIMING_REC8B = (1 << 2),
1531 IDE_TIMING_CYC8B = (1 << 3),
1532 IDE_TIMING_8BIT = IDE_TIMING_ACT8B | IDE_TIMING_REC8B |
1534 IDE_TIMING_ACTIVE = (1 << 4),
1535 IDE_TIMING_RECOVER = (1 << 5),
1536 IDE_TIMING_CYCLE = (1 << 6),
1537 IDE_TIMING_UDMA = (1 << 7),
1538 IDE_TIMING_ALL = IDE_TIMING_SETUP | IDE_TIMING_8BIT |
1539 IDE_TIMING_ACTIVE | IDE_TIMING_RECOVER |
1540 IDE_TIMING_CYCLE | IDE_TIMING_UDMA,
1543 struct ide_timing *ide_timing_find_mode(u8);
1544 u16 ide_pio_cycle_time(ide_drive_t *, u8);
1545 void ide_timing_merge(struct ide_timing *, struct ide_timing *,
1546 struct ide_timing *, unsigned int);
1547 int ide_timing_compute(ide_drive_t *, u8, struct ide_timing *, int, int);
1549 int ide_scan_pio_blacklist(char *);
1551 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
1553 int ide_set_pio_mode(ide_drive_t *, u8);
1554 int ide_set_dma_mode(ide_drive_t *, u8);
1556 void ide_set_pio(ide_drive_t *, u8);
1558 static inline void ide_set_max_pio(ide_drive_t *drive)
1560 ide_set_pio(drive, 255);
1563 extern spinlock_t ide_lock;
1564 extern struct mutex ide_cfg_mtx;
1566 * Structure locking:
1568 * ide_cfg_mtx and ide_lock together protect changes to
1569 * ide_hwif_t->{next,hwgroup}
1572 * ide_hwgroup_t->busy: ide_lock
1573 * ide_hwgroup_t->hwif: ide_lock
1574 * ide_hwif_t->mate: constant, no locking
1575 * ide_drive_t->hwif: constant, no locking
1578 #define local_irq_set(flags) do { local_save_flags((flags)); local_irq_enable_in_hardirq(); } while (0)
1580 extern struct bus_type ide_bus_type;
1581 extern struct class *ide_port_class;
1583 static inline void ide_dump_identify(u8 *id)
1585 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);
1588 static inline int hwif_to_node(ide_hwif_t *hwif)
1590 return hwif->dev ? dev_to_node(hwif->dev) : -1;
1593 static inline ide_drive_t *ide_get_pair_dev(ide_drive_t *drive)
1595 ide_drive_t *peer = &drive->hwif->drives[(drive->dn ^ 1) & 1];
1597 return (peer->dev_flags & IDE_DFLAG_PRESENT) ? peer : NULL;