2 * Copyright (C) ST-Ericsson SA 2010
4 * License Terms: GNU General Public License, version 2
5 * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
8 #ifndef __LINUX_MFD_STMPE_H
9 #define __LINUX_MFD_STMPE_H
11 #include <linux/device.h>
14 STMPE_BLOCK_GPIO = 1 << 0,
15 STMPE_BLOCK_KEYPAD = 1 << 1,
16 STMPE_BLOCK_TOUCHSCREEN = 1 << 2,
17 STMPE_BLOCK_ADC = 1 << 3,
18 STMPE_BLOCK_PWM = 1 << 4,
19 STMPE_BLOCK_ROTATOR = 1 << 5,
30 * For registers whose locations differ on variants, the correct address is
31 * obtained by indexing stmpe->regs with one of the following.
45 STMPE_IDX_GPAFR_U_MSB,
46 STMPE_IDX_IEGPIOR_LSB,
47 STMPE_IDX_ISGPIOR_MSB,
52 struct stmpe_variant_info;
53 struct stmpe_client_info;
56 * struct stmpe - STMPE MFD structure
57 * @lock: lock protecting I/O operations
58 * @irq_lock: IRQ bus lock
59 * @dev: device, mostly for dev_dbg()
60 * @client: client - i2c or spi
61 * @ci: client specific information
62 * @partnum: part number
63 * @variant: the detected STMPE model number
64 * @regs: list of addresses of registers which are at different addresses on
65 * different variants. Indexed by one of STMPE_IDX_*.
66 * @irq: irq number for stmpe
67 * @irq_base: starting IRQ number for internal IRQs
68 * @num_gpios: number of gpios, differs for variants
69 * @ier: cache of IER registers for bus_lock
70 * @oldier: cache of IER registers for bus_lock
71 * @pdata: platform data
75 struct mutex irq_lock;
78 struct stmpe_client_info *ci;
79 enum stmpe_partnum partnum;
80 struct stmpe_variant_info *variant;
88 struct stmpe_platform_data *pdata;
91 extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data);
92 extern int stmpe_reg_read(struct stmpe *stmpe, u8 reg);
93 extern int stmpe_block_read(struct stmpe *stmpe, u8 reg, u8 length,
95 extern int stmpe_block_write(struct stmpe *stmpe, u8 reg, u8 length,
97 extern int stmpe_set_bits(struct stmpe *stmpe, u8 reg, u8 mask, u8 val);
98 extern int stmpe_set_altfunc(struct stmpe *stmpe, u32 pins,
99 enum stmpe_block block);
100 extern int stmpe_enable(struct stmpe *stmpe, unsigned int blocks);
101 extern int stmpe_disable(struct stmpe *stmpe, unsigned int blocks);
103 struct matrix_keymap_data;
106 * struct stmpe_keypad_platform_data - STMPE keypad platform data
107 * @keymap_data: key map table and size
108 * @debounce_ms: debounce interval, in ms. Maximum is
109 * %STMPE_KEYPAD_MAX_DEBOUNCE.
110 * @scan_count: number of key scanning cycles to confirm key data.
111 * Maximum is %STMPE_KEYPAD_MAX_SCAN_COUNT.
112 * @no_autorepeat: disable key autorepeat
114 struct stmpe_keypad_platform_data {
115 struct matrix_keymap_data *keymap_data;
116 unsigned int debounce_ms;
117 unsigned int scan_count;
121 #define STMPE_GPIO_NOREQ_811_TOUCH (0xf0)
124 * struct stmpe_gpio_platform_data - STMPE GPIO platform data
125 * @gpio_base: first gpio number assigned. A maximum of
126 * %STMPE_NR_GPIOS GPIOs will be allocated.
127 * @norequest_mask: bitmask specifying which GPIOs should _not_ be
128 * requestable due to different usage (e.g. touch, keypad)
129 * STMPE_GPIO_NOREQ_* macros can be used here.
130 * @setup: board specific setup callback.
131 * @remove: board specific remove callback
133 struct stmpe_gpio_platform_data {
135 unsigned norequest_mask;
136 void (*setup)(struct stmpe *stmpe, unsigned gpio_base);
137 void (*remove)(struct stmpe *stmpe, unsigned gpio_base);
141 * struct stmpe_ts_platform_data - stmpe811 touch screen controller platform
143 * @sample_time: ADC converstion time in number of clock.
144 * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
145 * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
147 * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
148 * @ref_sel: ADC reference source
149 * (0 -> internal reference, 1 -> external reference)
150 * @adc_freq: ADC Clock speed
151 * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
152 * @ave_ctrl: Sample average control
153 * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
154 * @touch_det_delay: Touch detect interrupt delay
155 * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
156 * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
158 * @settling: Panel driver settling time
159 * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
160 * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
162 * @fraction_z: Length of the fractional part in z
163 * (fraction_z ([0..7]) = Count of the fractional part)
165 * @i_drive: current limit value of the touchscreen drivers
166 * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
169 struct stmpe_ts_platform_data {
182 * struct stmpe_platform_data - STMPE platform data
183 * @id: device id to distinguish between multiple STMPEs on the same board
184 * @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
185 * @irq_trigger: IRQ trigger to use for the interrupt to the host
186 * @irq_invert_polarity: IRQ line is connected with reversed polarity
187 * @autosleep: bool to enable/disable stmpe autosleep
188 * @autosleep_timeout: inactivity timeout in milliseconds for autosleep
189 * @irq_base: base IRQ number. %STMPE_NR_IRQS irqs will be used, or
190 * %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
191 * @irq_over_gpio: true if gpio is used to get irq
192 * @irq_gpio: gpio number over which irq will be requested (significant only if
193 * irq_over_gpio is true)
194 * @gpio: GPIO-specific platform data
195 * @keypad: keypad-specific platform data
196 * @ts: touchscreen-specific platform data
198 struct stmpe_platform_data {
202 unsigned int irq_trigger;
203 bool irq_invert_polarity;
207 int autosleep_timeout;
209 struct stmpe_gpio_platform_data *gpio;
210 struct stmpe_keypad_platform_data *keypad;
211 struct stmpe_ts_platform_data *ts;
214 #define STMPE_NR_INTERNAL_IRQS 9
215 #define STMPE_INT_GPIO(x) (STMPE_NR_INTERNAL_IRQS + (x))
217 #define STMPE_NR_GPIOS 24
218 #define STMPE_NR_IRQS STMPE_INT_GPIO(STMPE_NR_GPIOS)