menu "CAN Device Drivers" depends on CAN config CAN_VCAN tristate "Virtual Local CAN Interface (vcan)" depends on CAN default N ---help--- Similar to the network loopback devices, vcan offers a virtual local CAN interface. This driver can also be built as a module. If so, the module will be called vcan. config CAN_SLCAN tristate "Serial / USB serial CAN Adaptors (slcan)" depends on CAN default N ---help--- CAN driver for several 'low cost' CAN interfaces that are attached via serial lines or via USB-to-serial adapters using the LAWICEL ASCII protocol. The driver implements the tty linediscipline N_SLCAN. As only the sending and receiving of CAN frames is implemented, this driver should work with the (serial/USB) CAN hardware from: www.canusb.com / www.can232.com / www.mictronic.com / www.canhack.de Userspace tools to attach the SLCAN line discipline (slcan_attach, slcand) can be found in the can-utils at the SocketCAN SVN, see http://developer.berlios.de/projects/socketcan for details. The slcan driver supports up to 10 CAN netdevices by default which can be changed by the 'maxdev=xx' module option. This driver can also be built as a module. If so, the module will be called slcan. config CAN_DEV tristate "Platform CAN drivers with Netlink support" depends on CAN default Y ---help--- Enables the common framework for platform CAN drivers with Netlink support. This is the standard library for CAN drivers. If unsure, say Y. config CAN_CALC_BITTIMING bool "CAN bit-timing calculation" depends on CAN_DEV default Y ---help--- If enabled, CAN bit-timing parameters will be calculated for the bit-rate specified via Netlink argument "bitrate" when the device get started. This works fine for the most common CAN controllers with standard bit-rates but may fail for exotic bit-rates or CAN source clock frequencies. Disabling saves some space, but then the bit-timing parameters must be specified directly using the Netlink arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". If unsure, say Y. config CAN_AT91 tristate "Atmel AT91 onchip CAN controller" depends on CAN_DEV && ARCH_AT91SAM9263 ---help--- This is a driver for the SoC CAN controller in Atmel's AT91SAM9263. config CAN_TI_HECC depends on CAN_DEV && ARCH_OMAP3 tristate "TI High End CAN Controller" ---help--- Driver for TI HECC (High End CAN Controller) module found on many TI devices. The device specifications are available from www.ti.com config CAN_MCP251X tristate "Microchip MCP251x SPI CAN controllers" depends on CAN_DEV && SPI && HAS_DMA ---help--- Driver for the Microchip MCP251x SPI CAN controllers. config CAN_BFIN depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x) tristate "Analog Devices Blackfin on-chip CAN" ---help--- Driver for the Analog Devices Blackfin on-chip CAN controllers To compile this driver as a module, choose M here: the module will be called bfin_can. config CAN_JANZ_ICAN3 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" depends on CAN_DEV && MFD_JANZ_CMODIO ---help--- Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which connects to a MODULbus carrier board. This driver can also be built as a module. If so, the module will be called janz-ican3.ko. config HAVE_CAN_FLEXCAN bool config CAN_FLEXCAN tristate "Support for Freescale FLEXCAN based chips" depends on CAN_DEV && HAVE_CAN_FLEXCAN ---help--- Say Y here if you want to support for Freescale FlexCAN. config PCH_CAN tristate "PCH CAN" depends on CAN_DEV && PCI ---help--- This driver is for PCH CAN of Topcliff which is an IOH for x86 embedded processor. This driver can access CAN bus. source "drivers/net/can/mscan/Kconfig" source "drivers/net/can/sja1000/Kconfig" source "drivers/net/can/usb/Kconfig" config CAN_DEBUG_DEVICES bool "CAN devices debugging messages" depends on CAN default N ---help--- Say Y here if you want the CAN device drivers to produce a bunch of debug messages to the system log. Select this if you are having a problem with CAN support and want to see more of what is going on. endmenu