atstk100x: move CONFIG_SYS_TEXT_BASE to header

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 4917e264433b7a27e3360f9135b6e8c452347c08..6f3748d6dc4c2a8d4ce491d92420acffa9e42d36 100644 (file)
--- a/README
+++ b/README
@@ -1,5 +1,5 @@
 #
 #

-# (C) Copyright 2000 - 2009
+# (C) Copyright 2000 - 2011

 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this


@@ -356,6 +356,13 @@ The following options need to be configured:
                Define this option if you want to enable the
                ICache only when Code runs from RAM.
 
                Define this option if you want to enable the
                ICache only when Code runs from RAM.
 

+- 85xx CPU Options:
+               CONFIG_SYS_FSL_TBCLK_DIV
+
+               Defines the core time base clock divider ratio compared to the
+               system clock.  On most PQ3 devices this is 8, on newer QorIQ
+               devices it can be 16 or 32.  The ratio varies from SoC to Soc.
+

 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
 - Intel Monahans options:
                CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 


@@ -468,6 +475,18 @@ The following options need to be configured:
                define this to a list of base addresses for each (supported)
                port. See e.g. include/configs/versatile.h
 
                define this to a list of base addresses for each (supported)
                port. See e.g. include/configs/versatile.h
 

+               CONFIG_PL011_SERIAL_RLCR
+
+               Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
+               have separate receive and transmit line control registers.  Set
+               this variable to initialize the extra register.
+
+               CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+               On some platforms (e.g. U8500) U-Boot is loaded by a second stage
+               boot loader that has already initialized the UART.  Define this
+               variable to flush the UART at init time.
+

 
 - Console Interface:
                Depending on board, define exactly one serial port
 
 - Console Interface:
                Depending on board, define exactly one serial port


@@ -625,6 +644,7 @@ The following options need to be configured:
                CONFIG_CMD_BOOTD          bootd
                CONFIG_CMD_CACHE        * icache, dcache
                CONFIG_CMD_CONSOLE        coninfo
                CONFIG_CMD_BOOTD          bootd
                CONFIG_CMD_CACHE        * icache, dcache
                CONFIG_CMD_CONSOLE        coninfo

+               CONFIG_CMD_CRC32        * crc32

                CONFIG_CMD_DATE         * support for RTC, date/time...
                CONFIG_CMD_DHCP         * DHCP support
                CONFIG_CMD_DIAG         * Diagnostics
                CONFIG_CMD_DATE         * support for RTC, date/time...
                CONFIG_CMD_DHCP         * DHCP support
                CONFIG_CMD_DIAG         * Diagnostics


@@ -637,18 +657,22 @@ The following options need to be configured:
                CONFIG_CMD_EDITENV        edit env variable
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_EDITENV        edit env variable
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx

+               CONFIG_CMD_EXPORTENV    * export the environment

                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support
                CONFIG_CMD_FAT          * FAT partition support
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support
                CONFIG_CMD_FAT          * FAT partition support
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support

+               CONFIG_CMD_GO           * the 'go' command (exec code)
+               CONFIG_CMD_GREPENV      * search environment

                CONFIG_CMD_HWFLOW       * RTS/CTS hw flow control
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
                CONFIG_CMD_IMLS           List all found images
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_HWFLOW       * RTS/CTS hw flow control
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
                CONFIG_CMD_IMLS           List all found images
                CONFIG_CMD_IMMAP        * IMMR dump support

+               CONFIG_CMD_IMPORTENV    * import an environment

                CONFIG_CMD_IRQ          * irqinfo
                CONFIG_CMD_ITEST          Integer/string test of 2 values
                CONFIG_CMD_JFFS2        * JFFS2 Support
                CONFIG_CMD_IRQ          * irqinfo
                CONFIG_CMD_ITEST          Integer/string test of 2 values
                CONFIG_CMD_JFFS2        * JFFS2 Support


@@ -715,10 +739,17 @@ The following options need to be configured:
 - Watchdog:
                CONFIG_WATCHDOG
                If this variable is defined, it enables watchdog
 - Watchdog:
                CONFIG_WATCHDOG
                If this variable is defined, it enables watchdog

-               support. There must be support in the platform specific
-               code for a watchdog. For the 8xx and 8260 CPUs, the
-               SIU Watchdog feature is enabled in the SYPCR
-               register.
+               support for the SoC. There must be support in the SoC
+               specific code for a watchdog. For the 8xx and 8260
+               CPUs, the SIU Watchdog feature is enabled in the SYPCR
+               register.  When supported for a specific SoC is
+               available, then no further board specific code should
+               be needed to use it.
+
+               CONFIG_HW_WATCHDOG
+               When using a watchdog circuitry external to the used
+               SoC, then define this variable and provide board
+               specific code for the "hw_watchdog_reset" function.

 
 - U-Boot Version:
                CONFIG_VERSION_VARIABLE
 
 - U-Boot Version:
                CONFIG_VERSION_VARIABLE


@@ -744,6 +775,8 @@ The following options need to be configured:
                CONFIG_RTC_ISL1208      - use Intersil ISL1208 RTC
                CONFIG_RTC_MAX6900      - use Maxim, Inc. MAX6900 RTC
                CONFIG_SYS_RTC_DS1337_NOOSC     - Turn off the OSC output for DS1337
                CONFIG_RTC_ISL1208      - use Intersil ISL1208 RTC
                CONFIG_RTC_MAX6900      - use Maxim, Inc. MAX6900 RTC
                CONFIG_SYS_RTC_DS1337_NOOSC     - Turn off the OSC output for DS1337

+               CONFIG_SYS_RV3029_TCR   - enable trickle charger on
+                                         RV3029 RTC.

 
                Note that if the RTC uses I2C, then the I2C interface
                must also be configured. See I2C Support, below.
 
                Note that if the RTC uses I2C, then the I2C interface
                must also be configured. See I2C Support, below.


@@ -1089,13 +1122,10 @@ The following options need to be configured:
                        CONFIG_VIDEO_LOGO
                        CONFIG_VIDEO_BMP_LOGO
 
                        CONFIG_VIDEO_LOGO
                        CONFIG_VIDEO_BMP_LOGO
 

-               The DIU driver will look for the 'monitor' environment variable,
-               and if defined, enable the DIU as a console during boot.  This
-               variable should be set to one of these values:
-
-                       '0'     Output video to the DVI connector
-                       '1'     Output video to the LVDS connector
-                       '2'     Output video to the Dual-Link LVDS connector
+               The DIU driver will look for the 'video-mode' environment
+               variable, and if defined, enable the DIU as a console during
+               boot.  See the documentation file README.video for a
+               description of this variable.

 
 - Keyboard Support:
                CONFIG_KEYBOARD
 
 - Keyboard Support:
                CONFIG_KEYBOARD


@@ -1299,7 +1329,6 @@ The following options need to be configured:
                driver in use must provide a function: mcast() to join/leave a
                multicast group.
 
                driver in use must provide a function: mcast() to join/leave a
                multicast group.
 

-               CONFIG_BOOTP_RANDOM_DELAY

 - BOOTP Recovery Mode:
                CONFIG_BOOTP_RANDOM_DELAY
 
 - BOOTP Recovery Mode:
                CONFIG_BOOTP_RANDOM_DELAY
 


@@ -2005,6 +2034,20 @@ The following options need to be configured:
                thus overwriting the architecutre dependent default
                settings.
 
                thus overwriting the architecutre dependent default
                settings.
 

+- Frame Buffer Address:
+       CONFIG_FB_ADDR
+
+       Define CONFIG_FB_ADDR if you want to use specific address for
+       frame buffer.
+       Then system will reserve the frame buffer address to defined address
+       instead of lcd_setmem (this function grab the memory for frame buffer
+       by panel's size).
+
+       Please see board_init_f function.
+
+       If you want this config option then,
+       please define it at your board config file
+

 Legacy uImage format:
 
   Arg  Where                   When
 Legacy uImage format:
 
   Arg  Where                   When


@@ -2342,7 +2385,10 @@ Configuration Settings:
                used) must be put below this limit, unless "bootm_low"
                enviroment variable is defined and non-zero. In such case
                all data for the Linux kernel must be between "bootm_low"
                used) must be put below this limit, unless "bootm_low"
                enviroment variable is defined and non-zero. In such case
                all data for the Linux kernel must be between "bootm_low"

-               and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+               and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.  The environment
+               variable "bootm_mapsize" will override the value of
+               CONFIG_SYS_BOOTMAPSZ.  If CONFIG_SYS_BOOTMAPSZ is undefined,
+               then the value in "bootm_size" will be used instead.

 
 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
                Enable initrd_high functionality.  If defined then the
 
 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
                Enable initrd_high functionality.  If defined then the


@@ -2730,6 +2776,14 @@ Low Level (hardware related) configuration options:
                source code. It is used to make hardware dependant
                initializations.
 
                source code. It is used to make hardware dependant
                initializations.
 

+- CONFIG_IDE_AHB:
+               Most IDE controllers were designed to be connected with PCI
+               interface. Only few of them were designed for AHB interface.
+               When software is doing ATA command and data transfer to
+               IDE devices through IDE-AHB controller, some additional
+               registers accessing to these kind of IDE-AHB controller
+               is requierd.
+

 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're
                doing! (11-4) [MPC8xx/82xx systems only]
 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're
                doing! (11-4) [MPC8xx/82xx systems only]


@@ -2938,6 +2992,12 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 

+- CONFIG_USE_ARCH_MEMCPY
+  CONFIG_USE_ARCH_MEMSET
+               If these options are used a optimized version of memcpy/memset will
+               be used if available. These functions may be faster under some
+               conditions but may increase the binary size.
+

 Building the Software:
 ======================
 
 Building the Software:
 ======================
 


@@ -3178,7 +3238,16 @@ List of environment variables (most likely not complete):
                  for use by the bootm command. See also "bootm_size"
                  environment variable. Address defined by "bootm_low" is
                  also the base of the initial memory mapping for the Linux
                  for use by the bootm command. See also "bootm_size"
                  environment variable. Address defined by "bootm_low" is
                  also the base of the initial memory mapping for the Linux

-                 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+                 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+                 bootm_mapsize.
+
+  bootm_mapsize        - Size of the initial memory mapping for the Linux kernel.
+                 This variable is given as a hexadecimal number and it
+                 defines the size of the memory region starting at base
+                 address bootm_low that is accessible by the Linux kernel
+                 during early boot.  If unset, CONFIG_SYS_BOOTMAPSZ is used
+                 as the default value if it is defined, and bootm_size is
+                 used otherwise.

 
   bootm_size   - Memory range available for image processing in the bootm
                  command can be restricted. This variable is given as
 
   bootm_size   - Memory range available for image processing in the bootm
                  command can be restricted. This variable is given as