+ CONFIG_SYS_NAND_ONFI_DETECTION
+ Enables detection of ONFI compliant devices during probe.
+ And fetching device parameters flashed on device, by parsing
+ ONFI parameter page.
+
+ CONFIG_BCH
+ Enables software based BCH ECC algorithm present in lib/bch.c
+ This is used by SoC platforms which do not have built-in ELM
+ hardware engine required for BCH ECC correction.
+
+
+Platform specific options
+=========================
+ CONFIG_NAND_OMAP_GPMC
+ Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
+ GPMC controller is used for parallel NAND flash devices, and can
+ do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
+ and BCH16 ECC algorithms.
+
+ CONFIG_NAND_OMAP_ELM
+ Enables omap_elm.c driver for OMAPx and AMxxxx platforms.
+ ELM controller is used for ECC error detection (not ECC calculation)
+ of BCH4, BCH8 and BCH16 ECC algorithms.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ thus such SoC platforms need to depend on software library for ECC error
+ detection. However ECC calculation on such plaforms would still be
+ done by GPMC controller.
+
+ CONFIG_SPL_NAND_AM33XX_BCH
+ Enables SPL-NAND driver (am335x_spl_bch.c) which supports ELM based
+ hardware ECC correction. This is useful for platforms which have ELM
+ hardware engine and use NAND boot mode.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
+ SPL-NAND driver with software ECC correction support.
+
+ CONFIG_NAND_OMAP_ECCSCHEME
+ On OMAP platforms, this CONFIG specifies NAND ECC scheme.
+ It can take following values:
+ OMAP_ECC_HAM1_CODE_SW
+ 1-bit Hamming code using software lib.
+ (for legacy devices only)
+ OMAP_ECC_HAM1_CODE_HW
+ 1-bit Hamming code using GPMC hardware.
+ (for legacy devices only)
+ OMAP_ECC_BCH4_CODE_HW_DETECTION_SW
+ 4-bit BCH code (unsupported)
+ OMAP_ECC_BCH4_CODE_HW
+ 4-bit BCH code (unsupported)
+ OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+ 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using software library.
+ - requires CONFIG_BCH to enable software BCH library
+ (For legacy device which do not have ELM h/w engine)
+ OMAP_ECC_BCH8_CODE_HW
+ 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using ELM hardware engine.
+ OMAP_ECC_BCH16_CODE_HW
+ 16-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using ELM hardware engine.
+
+ How to select ECC scheme on OMAP and AMxx platforms ?
+ -----------------------------------------------------
+ Though higher ECC schemes have more capability to detect and correct
+ bit-flips, but still selection of ECC scheme is dependent on following
+ - hardware engines present in SoC.
+ Some legacy OMAP SoC do not have ELM h/w engine thus such
+ SoC cannot support BCHx_HW ECC schemes.
+ - size of OOB/Spare region
+ With higher ECC schemes, more OOB/Spare area is required to
+ store ECC. So choice of ECC scheme is limited by NAND oobsize.
+
+ In general following expression can help:
+ NAND_OOBSIZE >= 2 + (NAND_PAGESIZE / 512) * ECC_BYTES
+ where
+ NAND_OOBSIZE = number of bytes available in
+ OOB/spare area per NAND page.
+ NAND_PAGESIZE = bytes in main-area of NAND page.
+ ECC_BYTES = number of ECC bytes generated to
+ protect 512 bytes of data, which is:
+ 3 for HAM1_xx ecc schemes
+ 7 for BCH4_xx ecc schemes
+ 14 for BCH8_xx ecc schemes
+ 26 for BCH16_xx ecc schemes
+
+ example to check for BCH16 on 2K page NAND
+ NAND_PAGESIZE = 2048
+ NAND_OOBSIZE = 64
+ 2 + (2048 / 512) * 26 = 106 > NAND_OOBSIZE
+ Thus BCH16 cannot be supported on 2K page NAND.
+
+ However, for 4K pagesize NAND
+ NAND_PAGESIZE = 4096
+ NAND_OOBSIZE = 64
+ ECC_BYTES = 26
+ 2 + (4096 / 512) * 26 = 210 < NAND_OOBSIZE
+ Thus BCH16 can be supported on 4K page NAND.
+
+
+ CONFIG_NAND_OMAP_GPMC_PREFETCH
+ On OMAP platforms that use the GPMC controller
+ (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
+ uses the prefetch mode to speed up read operations.