AVR32 AVR32 architecture is enabled.
AX25 Appropriate AX.25 support is enabled.
BLACKFIN Blackfin architecture is enabled.
+ DRM Direct Rendering Management support is enabled.
+ DYNAMIC_DEBUG Build in debug messages and enable them at runtime
EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
EFI EFI Partitioning (GPT) is enabled
EIDE EIDE/ATAPI support is enabled.
- DRM Direct Rendering Management support is enabled.
- DYNAMIC_DEBUG Build in debug messages and enable them at runtime
FB The frame buffer device is enabled.
GCOV GCOV profiling is enabled.
HW Appropriate hardware is enabled.
unusable. The "log_buf_len" parameter may be useful
if you need to capture more output.
- acpi_display_output= [HW,ACPI]
- acpi_display_output=vendor
- acpi_display_output=video
- See above.
-
acpi_irq_balance [HW,ACPI]
ACPI will balance active IRQs
default in APIC mode
bttv.pll= See Documentation/video4linux/bttv/Insmod-options
bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
+ bulk_remove=off [PPC] This parameter disables the use of the pSeries
+ firmware feature for flushing multiple hpte entries
+ at a time.
+
c101= [NET] Moxa C101 synchronous serial card
cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
dscc4.setup= [NET]
- dynamic_printk Enables pr_debug()/dev_dbg() calls if
- CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
- These can also be switched on/off via
- <debugfs>/dynamic_printk/modules
-
earlycon= [KNL] Output early console device and options.
uart[8250],io,<addr>[,options]
uart[8250],mmio,<addr>[,options]
arch/x86/kernel/cpu/cpufreq/elanfreq.c.
elevator= [IOSCHED]
- Format: {"anticipatory" | "cfq" | "deadline" | "noop"}
+ Format: {"cfq" | "deadline" | "noop"}
See Documentation/block/as-iosched.txt and
Documentation/block/deadline-iosched.txt for details.
mtdparts= [MTD]
See drivers/mtd/cmdlinepart.c.
+ multitce=off [PPC] This parameter disables the use of the pSeries
+ firmware feature for updating multiple TCE entries
+ at a time.
+
onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
Format: [panic,][num]
- Valid num: 0,1,2
+ Valid num: 0
0 - turn nmi_watchdog off
- 1 - use the IO-APIC timer for the NMI watchdog
- 2 - use the local APIC for the NMI watchdog using
- a performance counter. Note: This will use one
- performance counter and the local APIC's performance
- vector.
When panic is specified, panic when an NMI watchdog
timeout occurs.
This is useful when you use a panic=... timeout and
need the box quickly up again.
- Instead of 1 and 2 it is possible to use the following
- symbolic names: lapic and ioapic
- Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
netpoll.carrier_timeout=
[NET] Specifies amount of time (in seconds) that
noapic [SMP,APIC] Tells the kernel to not make use of any
IOAPICs that may be present in the system.
+ noautogroup Disable scheduler automatic task group creation.
+
nobats [PPC] Do not use BATs for mapping kernel lowmem
on "Classic" PPC cores.
no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver
+ no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page
+ fault handling.
+
nolapic [X86-32,APIC] Do not enable or use the local APIC.
nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
nousb [USB] Disable the USB subsystem
- nowatchdog [KNL] Disable the lockup detector.
+ nowatchdog [KNL] Disable the lockup detector (NMI watchdog).
nowb [ARM]
reset_devices [KNL] Force drivers to reset the underlying device
during initialization.
- resource_alloc_from_bottom
- Allocate new resources from the beginning of available
- space, not the end. If you need to use this, please
- report a bug.
-
resume= [SWSUSP]
Specify the partition device for software suspend
improve throughput, but will also increase the
amount of memory reserved for use by the client.
+ swapaccount[=0|1]
+ [KNL] Enable accounting of swap in memory resource
+ controller if no parameter or 1 is given or disable
+ it if 0 is given (See Documentation/cgroups/memory.txt)
+
swiotlb= [IA-64] Number of I/O TLB slabs
switches= [HW,M68k]
to facilitate early boot debugging.
See also Documentation/trace/events.txt
- tsc= Disable clocksource-must-verify flag for TSC.
+ tsc= Disable clocksource stability checks for TSC.
Format: <string>
[x86] reliable: mark tsc clocksource as reliable, this
- disables clocksource verification at runtime.
- Used to enable high-resolution timer mode on older
- hardware, and in virtualized environment.
+ disables clocksource verification at runtime, as well
+ as the stability checks done at bootup. Used to enable
+ high-resolution timer mode on older hardware, and in
+ virtualized environment.
[x86] noirqtime: Do not use TSC to do irq accounting.
Used to run time disable IRQ_TIME_ACCOUNTING on any
platforms where RDTSC is slow and this accounting
projects / mv-sheeva.git / blobdiff