Documentation: explain [KMG] parameter suffix

[mv-sheeva.git] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index ed3708f8d0dbae4ec5ad73bd3056aeda1c06b73d..66771a34f1858171d3823521f183051c9562a26e 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -43,11 +43,11 @@ parameter is applicable:
        AVR32   AVR32 architecture is enabled.
        AX25    Appropriate AX.25 support is enabled.
        BLACKFIN Blackfin architecture is enabled.
+       DRM     Direct Rendering Management support is enabled.
+       DYNAMIC_DEBUG Build in debug messages and enable them at runtime
        EDD     BIOS Enhanced Disk Drive Services (EDD) is enabled
        EFI     EFI Partitioning (GPT) is enabled
        EIDE    EIDE/ATAPI support is enabled.
-       DRM     Direct Rendering Management support is enabled.
-       DYNAMIC_DEBUG Build in debug messages and enable them at runtime
        FB      The frame buffer device is enabled.
        GCOV    GCOV profiling is enabled.
        HW      Appropriate hardware is enabled.
@@ -144,6 +144,11 @@ a fixed number of characters. This limit depends on the architecture
 and is between 256 and 4096 characters. It is defined in the file
 ./include/asm/setup.h as COMMAND_LINE_SIZE.
 
+Finally, the [KMG] suffix is commonly described after a number of kernel
+parameter values. These 'K', 'M', and 'G' letters represent the _binary_
+multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30
+bytes respectively. Such letter suffixes can also be entirely omitted.
+
 
        acpi=           [HW,ACPI,X86]
                        Advanced Configuration and Power Interface
@@ -199,11 +204,6 @@ and is between 256 and 4096 characters. It is defined in the file
                        unusable.  The "log_buf_len" parameter may be useful
                        if you need to capture more output.
 
-       acpi_display_output=    [HW,ACPI]
-                       acpi_display_output=vendor
-                       acpi_display_output=video
-                       See above.
-
        acpi_irq_balance [HW,ACPI]
                        ACPI will balance active IRQs
                        default in APIC mode
@@ -550,16 +550,20 @@ and is between 256 and 4096 characters. It is defined in the file
                        Format:
                        <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
 
-       crashkernel=nn[KMG]@ss[KMG]
-                       [KNL] Reserve a chunk of physical memory to
-                       hold a kernel to switch to with kexec on panic.
+       crashkernel=size[KMG][@offset[KMG]]
+                       [KNL] Using kexec, Linux can switch to a 'crash kernel'
+                       upon panic. This parameter reserves the physical
+                       memory region [offset, offset + size] for that kernel
+                       image. If '@offset' is omitted, then a suitable offset
+                       is selected automatically. Check
+                       Documentation/kdump/kdump.txt for further details.
 
        crashkernel=range1:size1[,range2:size2,...][@offset]
                        [KNL] Same as above, but depends on the memory
                        in the running system. The syntax of range is
                        start-[end] where start and end are both
                        a memory unit (amount[KMG]). See also
-                       Documentation/kdump/kdump.txt for a example.
+                       Documentation/kdump/kdump.txt for an example.
 
        cs89x0_dma=     [HW,NET]
                        Format: <dma>
@@ -659,11 +663,6 @@ and is between 256 and 4096 characters. It is defined in the file
 
        dscc4.setup=    [NET]
 
-       dynamic_printk  Enables pr_debug()/dev_dbg() calls if
-                       CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
-                       These can also be switched on/off via
-                       <debugfs>/dynamic_printk/modules
-
        earlycon=       [KNL] Output early console device and options.
                uart[8250],io,<addr>[,options]
                uart[8250],mmio,<addr>[,options]
@@ -888,6 +887,7 @@ and is between 256 and 4096 characters. It is defined in the file
                             controller
        i8042.nopnp     [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
                             controllers
+       i8042.notimeout [HW] Ignore timeout condition signalled by conroller
        i8042.reset     [HW] Reset the controller during init and cleanup
        i8042.unlock    [HW] Unlock (ignore) the keylock
 
@@ -1709,6 +1709,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
        no-kvmclock     [X86,KVM] Disable paravirtualized KVM clock driver
 
+       no-kvmapf       [X86,KVM] Disable paravirtualized asynchronous page
+                       fault handling.
+
        nolapic         [X86-32,APIC] Do not enable or use the local APIC.
 
        nolapic_timer   [X86-32,APIC] Do not use the local APIC timer.