Merge remote-tracking branch 'block/for-next'

[karo-tx-linux.git] / Documentation / networking / batman-adv.txt

diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt
index c1d82047a4b151c35983656e5841e261ff22fd7f..89490beb3c0bf6bd0160c891b51e3cf07497f1ca 100644 (file)
--- a/Documentation/networking/batman-adv.txt
+++ b/Documentation/networking/batman-adv.txt
@@ -69,8 +69,7 @@ folder:
 # aggregated_ogms        gw_bandwidth           log_level
 # ap_isolation           gw_mode                orig_interval
 # bonding                gw_sel_class           routing_algo
-# bridge_loop_avoidance  hop_penalty            vis_mode
-# fragmentation
+# bridge_loop_avoidance  hop_penalty            fragmentation
 
 
 There is a special folder for debugging information:
@@ -78,7 +77,7 @@ There is a special folder for debugging information:
 # ls /sys/kernel/debug/batman_adv/bat0/
 # bla_backbone_table  log                 transtable_global
 # bla_claim_table     originators         transtable_local
-# gateways            socket              vis_data
+# gateways            socket
 
 Some of the files contain all sort of status information  regard-
 ing  the  mesh  network.  For  example, you can view the table of
@@ -127,51 +126,6 @@ ously assigned to interfaces now used by batman advanced, e.g.
 # ifconfig eth0 0.0.0.0
 
 
-VISUALIZATION
--------------
-
-If you want topology visualization, at least one mesh  node  must
-be configured as VIS-server:
-
-# echo "server" > /sys/class/net/bat0/mesh/vis_mode
-
-Each  node  is  either configured as "server" or as "client" (de-
-fault: "client").  Clients send their topology data to the server
-next to them, and server synchronize with other servers. If there
-is no server configured (default) within the  mesh,  no  topology
-information   will  be  transmitted.  With  these  "synchronizing
-servers", there can be 1 or more vis servers sharing the same (or
-at least very similar) data.
-
-When  configured  as  server,  you can get a topology snapshot of
-your mesh:
-
-# cat /sys/kernel/debug/batman_adv/bat0/vis_data
-
-This raw output is intended to be easily parsable and convertable
-with  other tools. Have a look at the batctl README if you want a
-vis output in dot or json format for instance and how those  out-
-puts could then be visualised in an image.
-
-The raw format consists of comma separated values per entry where
-each entry is giving information about a  certain  source  inter-
-face.  Each  entry can/has to have the following values:
--> "mac" - mac address of an originator's source interface
-           (each line begins with it)
--> "TQ mac  value"  -  src mac's link quality towards mac address
-                       of a neighbor originator's interface which
-                       is being used for routing
--> "TT mac" - TT announced by source mac
--> "PRIMARY" - this  is a primary interface
--> "SEC mac" - secondary mac address of source
-               (requires preceding PRIMARY)
-
-The TQ value has a range from 4 to 255 with 255 being  the  best.
-The TT entries are showing which hosts are connected to the mesh
-via bat0 or being bridged into the mesh network.  The PRIMARY/SEC
-values are only applied on primary interfaces
-
-
 LOGGING/DEBUGGING
 -----------------
 
@@ -245,5 +199,5 @@ Mailing-list:   b.a.t.m.a.n@open-mesh.org (optional  subscription
 
 You can also contact the Authors:
 
-Marek  Lindner  <lindner_marek@yahoo.de>
-Simon  Wunderlich  <siwu@hrz.tu-chemnitz.de>
+Marek  Lindner  <mareklindner@neomailbox.ch>
+Simon  Wunderlich  <sw@simonwunderlich.de>