#
-# (C) Copyright 2000 - 2009
+# (C) Copyright 2000 - 2011
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
Define this option if you want to enable the
ICache only when Code runs from RAM.
+- 85xx CPU Options:
+ CONFIG_SYS_FSL_TBCLK_DIV
+
+ Defines the core time base clock divider ratio compared to the
+ system clock. On most PQ3 devices this is 8, on newer QorIQ
+ devices it can be 16 or 32. The ratio varies from SoC to Soc.
+
+ CONFIG_SYS_FSL_PCIE_COMPAT
+
+ Defines the string to utilize when trying to match PCIe device
+ tree nodes for the given platform.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
+ CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
+
+ This setting is mandatory for all boards that have only one
+ machine type and must be used to specify the machine type
+ number as it appears in the ARM machine registry
+ (see http://www.arm.linux.org.uk/developer/machines/).
+ Only boards that have multiple machine types supported
+ in a single configuration file and the machine type is
+ runtime discoverable, do not have to use this setting.
+
- vxWorks boot parameters:
bootvx constructs a valid bootline using the following
Note: If a "bootargs" environment is defined, it will overwride
the defaults discussed just above.
+- Cache Configuration:
+ CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
+ CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
+ CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
+
+- Cache Configuration for ARM:
+ CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
+ controller
+ CONFIG_SYS_PL310_BASE - Physical base address of PL310
+ controller register space
+
- Serial Ports:
CONFIG_PL010_SERIAL
define this to a list of base addresses for each (supported)
port. See e.g. include/configs/versatile.h
+ CONFIG_PL011_SERIAL_RLCR
+
+ Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
+ have separate receive and transmit line control registers. Set
+ this variable to initialize the extra register.
+
+ CONFIG_PL011_SERIAL_FLUSH_ON_INIT
+
+ On some platforms (e.g. U8500) U-Boot is loaded by a second stage
+ boot loader that has already initialized the UART. Define this
+ variable to flush the UART at init time.
+
- Console Interface:
Depending on board, define exactly one serial port
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_GO * the 'go' command (exec code)
+ CONFIG_CMD_GREPENV * search environment
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
+ CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
CONFIG_CMD_USB * USB support
- CONFIG_CMD_VFD * VFD support (TRAB)
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_FSL * Microblaze FSL support
- Watchdog:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
- support. There must be support in the platform specific
- code for a watchdog. For the 8xx and 8260 CPUs, the
- SIU Watchdog feature is enabled in the SYPCR
- register.
+ support for the SoC. There must be support in the SoC
+ specific code for a watchdog. For the 8xx and 8260
+ CPUs, the SIU Watchdog feature is enabled in the SYPCR
+ register. When supported for a specific SoC is
+ available, then no further board specific code should
+ be needed to use it.
+
+ CONFIG_HW_WATCHDOG
+ When using a watchdog circuitry external to the used
+ SoC, then define this variable and provide board
+ specific code for the "hw_watchdog_reset" function.
- U-Boot Version:
CONFIG_VERSION_VARIABLE
CONFIG_VIDEO_LOGO
CONFIG_VIDEO_BMP_LOGO
- The DIU driver will look for the 'monitor' environment variable,
- and if defined, enable the DIU as a console during boot. This
- variable should be set to one of these values:
-
- '0' Output video to the DVI connector
- '1' Output video to the LVDS connector
- '2' Output video to the Dual-Link LVDS connector
+ The DIU driver will look for the 'video-mode' environment
+ variable, and if defined, enable the DIU as a console during
+ boot. See the documentation file README.video for a
+ description of this variable.
- Keyboard Support:
CONFIG_KEYBOARD
driver in use must provide a function: mcast() to join/leave a
multicast group.
- CONFIG_BOOTP_RANDOM_DELAY
- BOOTP Recovery Mode:
CONFIG_BOOTP_RANDOM_DELAY
thus overwriting the architecutre dependent default
settings.
+- Frame Buffer Address:
+ CONFIG_FB_ADDR
+
+ Define CONFIG_FB_ADDR if you want to use specific address for
+ frame buffer.
+ Then system will reserve the frame buffer address to defined address
+ instead of lcd_setmem (this function grab the memory for frame buffer
+ by panel's size).
+
+ Please see board_init_f function.
+
+ If you want this config option then,
+ please define it at your board config file
+
Legacy uImage format:
Arg Where When
Modem Support:
--------------
-[so far only for SMDK2400 and TRAB boards]
+[so far only for SMDK2400 boards]
- Modem support enable:
CONFIG_MODEM_SUPPORT
used) must be put below this limit, unless "bootm_low"
enviroment variable is defined and non-zero. In such case
all data for the Linux kernel must be between "bootm_low"
- and "bootm_low" + CONFIG_SYS_BOOTMAPSZ.
+ and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
+ variable "bootm_mapsize" will override the value of
+ CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
+ then the value in "bootm_size" will be used instead.
- CONFIG_SYS_BOOT_RAMDISK_HIGH:
Enable initrd_high functionality. If defined then the
source code. It is used to make hardware dependant
initializations.
+- CONFIG_IDE_AHB:
+ Most IDE controllers were designed to be connected with PCI
+ interface. Only few of them were designed for AHB interface.
+ When software is doing ATA command and data transfer to
+ IDE devices through IDE-AHB controller, some additional
+ registers accessing to these kind of IDE-AHB controller
+ is requierd.
+
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
doing! (11-4) [MPC8xx/82xx systems only]
- CONFIG_SYS_SRIOn_MEM_SIZE:
Size of SRIO port 'n' memory region
+- CONFIG_SYS_NDFC_16
+ Defined to tell the NDFC that the NAND chip is using a
+ 16 bit bus.
+
+- CONFIG_SYS_NDFC_EBC0_CFG
+ Sets the EBC0_CFG register for the NDFC. If not defined
+ a default value will be used.
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
one, specify here. Note that the value must resolve
to something your driver can deal with.
+- CONFIG_SYS_DDR_RAW_TIMING
+ Get DDR timing information from other than SPD. Common with
+ soldered DDR chips onboard without SPD. DDR raw timing
+ parameters are extracted from datasheet and hard-coded into
+ header files or board specific files.
+
- CONFIG_SYS_83XX_DDR_USES_CS0
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
+- CONFIG_USE_ARCH_MEMCPY
+ CONFIG_USE_ARCH_MEMSET
+ If these options are used a optimized version of memcpy/memset will
+ be used if available. These functions may be faster under some
+ conditions but may increase the binary size.
+
Building the Software:
======================
for use by the bootm command. See also "bootm_size"
environment variable. Address defined by "bootm_low" is
also the base of the initial memory mapping for the Linux
- kernel -- see the description of CONFIG_SYS_BOOTMAPSZ.
+ kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
+ bootm_mapsize.
+
+ bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
+ This variable is given as a hexadecimal number and it
+ defines the size of the memory region starting at base
+ address bootm_low that is accessible by the Linux kernel
+ during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
+ as the default value if it is defined, and bootm_size is
+ used otherwise.
bootm_size - Memory range available for image processing in the bootm
command can be restricted. This variable is given as
This can be used to load and uncompress arbitrary
data.
+ fdt_high - if set this restricts the maximum address that the
+ flattened device tree will be copied into upon boot.
+ If this is set to the special value 0xFFFFFFFF then
+ the fdt will not be copied at all on boot. For this
+ to work it must reside in writable memory, have
+ sufficient padding on the end of it for u-boot to
+ add the information it needs into it, and the memory
+ must be accessible by the kernel.
+
i2cfast - (PPC405GP|PPC405EP only)
if set to 'y' configures Linux I2C driver for fast
mode (400kHZ). This environment variable is used in
projects / karo-tx-uboot.git / blobdiff