param header, the default value is zero if undefined.
- Serial Ports:
- CFG_PL010_SERIAL
+ CONFIG_PL010_SERIAL
Define this if you want support for Amba PrimeCell PL010 UARTs.
- CFG_PL011_SERIAL
+ CONFIG_PL011_SERIAL
Define this if you want support for Amba PrimeCell PL011 UARTs.
If defined, then this indicates the I2C bus number for the DTT.
If not defined, then U-Boot assumes that DTT is on I2C bus 0.
+ CFG_I2C_DTT_ADDR:
+
+ If defined, specifies the I2C address of the DTT device.
+ If not defined, then U-Boot uses predefined value for
+ specified DTT device.
+
CONFIG_FSL_I2C
Define this option if you want to use Freescale's I2C driver in
of environment data (variable area); in general, we support the
following configurations:
-- CFG_ENV_IS_IN_FLASH:
+- CONFIG_ENV_IS_IN_FLASH:
Define this if the environment is in flash memory.
environment in one of the last sectors, leaving a gap
between U-Boot and the environment.
- - CFG_ENV_OFFSET:
+ - CONFIG_ENV_OFFSET:
Offset of environment data (variable area) to the
beginning of flash memory; for instance, with bottom boot
type flash chips the second sector can be used: the offset
for this sector is given here.
- CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
+ CONFIG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
- - CFG_ENV_ADDR:
+ - CONFIG_ENV_ADDR:
This is just another way to specify the start address of
the flash sector containing the environment (instead of
- CFG_ENV_OFFSET).
+ CONFIG_ENV_OFFSET).
- - CFG_ENV_SECT_SIZE:
+ - CONFIG_ENV_SECT_SIZE:
Size of the sector containing the environment.
In such a case you don't want to spend a whole sector for
the environment.
- - CFG_ENV_SIZE:
+ - CONFIG_ENV_SIZE:
- If you use this in combination with CFG_ENV_IS_IN_FLASH
- and CFG_ENV_SECT_SIZE, you can specify to use only a part
+ If you use this in combination with CONFIG_ENV_IS_IN_FLASH
+ and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
of this flash sector for the environment. This saves
memory for the RAM copy of the environment.
wrong before the contents has been restored from a copy in
RAM, your target system will be dead.
- - CFG_ENV_ADDR_REDUND
- CFG_ENV_SIZE_REDUND
+ - CONFIG_ENV_ADDR_REDUND
+ CONFIG_ENV_SIZE_REDUND
These settings describe a second storage area used to hold
a redundant copy of the environment data, so that there is
accordingly!
-- CFG_ENV_IS_IN_NVRAM:
+- CONFIG_ENV_IS_IN_NVRAM:
Define this if you have some non-volatile memory device
(NVRAM, battery buffered SRAM) which you want to use for the
environment.
- - CFG_ENV_ADDR:
- - CFG_ENV_SIZE:
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
These two #defines are used to determine the memory area you
want to use for environment. It is assumed that this memory
to save the current settings.
-- CFG_ENV_IS_IN_EEPROM:
+- CONFIG_ENV_IS_IN_EEPROM:
Use this if you have an EEPROM or similar serial access
device and a driver for it.
- - CFG_ENV_OFFSET:
- - CFG_ENV_SIZE:
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the
environment area within the total memory of your EEPROM.
The size in bytes of the EEPROM device.
-- CFG_ENV_IS_IN_DATAFLASH:
+- CONFIG_ENV_IS_IN_DATAFLASH:
Define this if you have a DataFlash memory device which you
want to use for the environment.
- - CFG_ENV_OFFSET:
- - CFG_ENV_ADDR:
- - CFG_ENV_SIZE:
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
These three #defines specify the offset and size of the
environment area within the total memory of your DataFlash placed
at the specified address.
-- CFG_ENV_IS_IN_NAND:
+- CONFIG_ENV_IS_IN_NAND:
Define this if you have a NAND device which you want to use
for the environment.
- - CFG_ENV_OFFSET:
- - CFG_ENV_SIZE:
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
These two #defines specify the offset and size of the environment
area within the first NAND device.
- - CFG_ENV_OFFSET_REDUND
+ - CONFIG_ENV_OFFSET_REDUND
- This setting describes a second storage area of CFG_ENV_SIZE
+ This setting describes a second storage area of CONFIG_ENV_SIZE
size used to hold a redundant copy of the environment data,
so that there is a valid backup copy in case there is a
power failure during a "saveenv" operation.
- Note: CFG_ENV_OFFSET and CFG_ENV_OFFSET_REDUND must be aligned
- to a block boundary, and CFG_ENV_SIZE must be a multiple of
+ Note: CONFIG_ENV_OFFSET and CONFIG_ENV_OFFSET_REDUND must be aligned
+ to a block boundary, and CONFIG_ENV_SIZE must be a multiple of
the NAND devices block size.
- CFG_SPI_INIT_OFFSET
* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
- LynxOS, pSOS, QNX, RTEMS, ARTOS;
- Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
+ LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
+ Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
+ INTEGRITY).
* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
projects / karo-tx-uboot.git / blobdiff