#
-# (C) Copyright 2000 - 2011
+# (C) Copyright 2000 - 2012
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
XWAY SoCs for booting from NOR flash. The U-Boot image needs to
be swapped if a flash programmer is used.
+- ARM options:
+ CONFIG_SYS_EXCEPTION_VECTORS_HIGH
+
+ Select high exception vectors of the ARM core, e.g., do not
+ clear the V bit of the c1 register of CP15.
+
- Linux Kernel Interface:
CONFIG_CLOCKS_IN_MHZ
to get the character out. Baud rates will need to default
to something sensible.
+- Safe printf() functions
+ Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
+ the printf() functions. These are defined in
+ include/vsprintf.h and include snprintf(), vsnprintf() and
+ so on. Code size increase is approximately 300-500 bytes.
+ If this option is not given then these functions will
+ silently discard their buffer size argument - this means
+ you are not getting any overflow checking in this case.
+
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
+ CONFIG_CMD_SF * Read/write/erase SPI NOR flash
CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
If this defined, the driver is quiet.
The driver doen't show link status messages.
+ CONFIG_CALXEDA_XGMAC
+ Support for the Calxeda XGMAC device
+
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
for your device
- CONFIG_USBD_PRODUCTID 0xFFFF
+- ULPI Layer Support:
+ The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
+ the generic ULPI layer. The generic layer accesses the ULPI PHY
+ via the platform viewport, so you need both the genric layer and
+ the viewport enabled. Currently only Chipidea/ARC based
+ viewport is supported.
+ To enable the ULPI layer support, define CONFIG_USB_ULPI and
+ CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
- MMC Support:
The MMC controller on the Intel PXA is supported. To
allows to read/write in Dataflash via the standard
commands cp, md...
+- Serial Flash support
+ CONFIG_CMD_SF
+
+ Defining this option enables SPI flash commands
+ 'sf probe/read/write/erase/update'.
+
+ Usage requires an initial 'probe' to define the serial
+ flash parameters, followed by read/write/erase/update
+ commands.
+
+ The following defaults may be provided by the platform
+ to handle the common case when only a single serial
+ flash is present on the system.
+
+ CONFIG_SF_DEFAULT_BUS Bus identifier
+ CONFIG_SF_DEFAULT_CS Chip-select
+ CONFIG_SF_DEFAULT_MODE (see include/spi.h)
+ CONFIG_SF_DEFAULT_SPEED in Hz
+
- SystemACE Support:
CONFIG_SYSTEMACE
fdt_high - if set this restricts the maximum address that the
flattened device tree will be copied into upon boot.
+ For example, if you have a system with 1 GB memory
+ at physical address 0x10000000, while Linux kernel
+ only recognizes the first 704 MB as low memory, you
+ may need to set fdt_high as 0x3C000000 to have the
+ device tree blob be copied to the maximum address
+ of the 704 MB low memory, so that Linux kernel can
+ access it during the boot procedure.
+
If this is set to the special value 0xFFFFFFFF then
the fdt will not be copied at all on boot. For this
to work it must reside in writable memory, have