/blackfin Files generic to Analog Devices Blackfin architecture
/cpu CPU specific files
/lib Architecture specific library files
- /i386 Files generic to i386 architecture
+ /x86 Files generic to x86 architecture
/cpu CPU specific files
/lib Architecture specific library files
/m68k Files generic to m68k architecture
CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
CONFIG_SYS_8272ADS - MPC8272ADS
+- Marvell Family Member
+ CONFIG_SYS_MVFS - define it if you want to enable
+ multiple fs option at one time
+ for marvell soc family
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
CONFIG_CMD_CONSOLE coninfo
+ CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
CONFIG_CMD_ELF * bootelf, bootvx
+ CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT partition support
CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
+ CONFIG_CMD_GO * the 'go' command (exec code)
CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
CONFIG_CMD_I2C * I2C serial bus support
CONFIG_CMD_IDE * IDE harddisk support
CONFIG_CMD_IMI iminfo
CONFIG_CMD_IMLS List all found images
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_ITEST Integer/string test of 2 values
CONFIG_CMD_JFFS2 * JFFS2 Support
CONFIG_CMD_KGDB * kgdb
+ CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_SYS_RV3029_TCR - enable trickle charger on
+ RV3029 RTC.
Note that if the RTC uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
or CONFIG_VIDEO_SED13806_16BPP
+ CONFIG_FSL_DIU_FB
+ Enable the Freescale DIU video driver. Reference boards for
+ SOCs that have a DIU should define this macro to enable DIU
+ support, and should also define these other macros:
+
+ CONFIG_SYS_DIU_ADDR
+ CONFIG_VIDEO
+ CONFIG_CMD_BMP
+ CONFIG_CFB_CONSOLE
+ CONFIG_VIDEO_SW_CURSOR
+ CONFIG_VGA_AS_SINGLE_DEVICE
+ CONFIG_VIDEO_LOGO
+ CONFIG_VIDEO_BMP_LOGO
+
+ The DIU driver will look for the 'monitor' environment variable,
+ and if defined, enable the DIU as a console during boot. This
+ variable should be set to one of these values:
+
+ '0' Output video to the DVI connector
+ '1' Output video to the LVDS connector
+ '2' Output video to the Dual-Link LVDS connector
+
- Keyboard Support:
CONFIG_KEYBOARD
example, some LED's) on your board. At the moment,
the following checkpoints are implemented:
+- Standalone program support:
+ CONFIG_STANDALONE_LOAD_ADDR
+
+ This option allows to define board specific values
+ for the address where standalone program gets loaded,
+ thus overwriting the architecutre dependent default
+ settings.
+
Legacy uImage format:
Arg Where When