---------------------------------------------------
For all supported boards there are ready-to-use default
-configurations available; just type "make <board_name>_config".
+configurations available; just type "make <board_name>_defconfig".
Example: For a TQM823L module type:
cd u-boot
- make TQM823L_config
+ make TQM823L_defconfig
For the Cogent platform, you need to specify the CPU type as well;
-e.g. "make cogent_mpc8xx_config". And also configure the cogent
+e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent
directory according to the instructions in cogent/README.
4th and following
BOOTP requests: delay 0 ... 8 sec
+ CONFIG_BOOTP_ID_CACHE_SIZE
+
+ BOOTP packets are uniquely identified using a 32-bit ID. The
+ server will copy the ID from client requests to responses and
+ U-Boot will use this to determine if it is the destination of
+ an incoming response. Some servers will check that addresses
+ aren't in use before handing them out (usually using an ARP
+ ping) and therefore take up to a few hundred milliseconds to
+ respond. Network congestion may also influence the time it
+ takes for a response to make it back to the client. If that
+ time is too long, U-Boot will retransmit requests. In order
+ to allow earlier responses to still be accepted after these
+ retransmissions, U-Boot's BOOTP client keeps a small cache of
+ IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
+ cache. The default is to keep IDs for up to four outstanding
+ requests. Increasing this will allow U-Boot to accept offers
+ from a BOOTP client in networks with unusually high latency.
+
- DHCP Advanced Options:
You can fine tune the DHCP functionality by defining
CONFIG_BOOTP_* symbols:
Enables the driver for the SPI controllers on i.MX and MXC
SoCs. Currently i.MX31/35/51 are supported.
+ CONFIG_SYS_SPI_MXC_WAIT
+ Timeout for waiting until spi transfer completed.
+ default: (CONFIG_SYS_HZ/100) /* 10 ms */
+
- FPGA Support: CONFIG_FPGA
Enables FPGA subsystem.
- CONFIG_SYS_MALLOC_LEN:
Size of DRAM reserved for malloc() use.
+- CONFIG_SYS_MALLOC_F_LEN
+ Size of the malloc() pool for use before relocation. If
+ this is defined, then a very simple malloc() implementation
+ will become available before relocation. The address is just
+ below the global data, and the stack is moved down to make
+ space.
+
+ This feature allocates regions with increasing addresses
+ within the region. calloc() is supported, but realloc()
+ is not available. free() is supported but does nothing.
+ The memory will be freed (or in fact just forgotton) when
+ U-Boot relocates itself.
+
+ Pre-relocation malloc() is only supported on sandbox
+ at present but is fairly easy to enable for other archs.
+
+ Pre-relocation malloc() is only supported on ARM at present
+ but is fairly easy to enable for other archs.
+
- CONFIG_SYS_BOOTM_LEN:
Normally compressed uImages are limited to an
uncompressed size of 8 MBytes. If this is not enough,
sources you must configure U-Boot for one specific board type. This
is done by typing:
- make NAME_config
+ make NAME_defconfig
-where "NAME_config" is the name of one of the existing configu-
+where "NAME_defconfig" is the name of one of the existing configu-
rations; see boards.cfg for supported names.
Note: for some board special configuration names may exist; check if
or with LCD support. You can select such additional "features"
when choosing the configuration, i. e.
- make TQM823L_config
+ make TQM823L_defconfig
- will configure for a plain TQM823L, i. e. no LCD support
- make TQM823L_LCD_config
+ make TQM823L_LCD_defconfig
- will configure for a TQM823L with U-Boot console on LCD
etc.
1. Add O= to the make command line invocations:
make O=/tmp/build distclean
- make O=/tmp/build NAME_config
+ make O=/tmp/build NAME_defconfig
make O=/tmp/build all
2. Set environment variable BUILD_DIR to point to the desired location:
export BUILD_DIR=/tmp/build
make distclean
- make NAME_config
+ make NAME_defconfig
make all
Note that the command line "O=" setting overrides the BUILD_DIR environment
your board
3. If you're porting U-Boot to a new CPU, then also create a new
directory to hold your CPU specific code. Add any files you need.
-4. Run "make <board>_config" with your new name.
+4. Run "make <board>_defconfig" with your new name.
5. Type "make", and you should get a working "u-boot.srec" file
to be installed on your target system.
6. Debug and solve any problems that might arise.
Example:
- make TQM850L_config
+ make TQM850L_defconfig
make oldconfig
make dep
make uImage
projects / karo-tx-uboot.git / blobdiff