ARM: dts: omap3-overo: Add HSUSB PHY

[karo-tx-linux.git] / arch / arm / boot / dts / omap3-overo-base.dtsi

diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi
index edac70e9204ce3f629aff3605beeb3be218ef5b0..13d1ad21549430f60b21812fc3ba0d4ca3e5ecb2 100644 (file)
--- a/arch/arm/boot/dts/omap3-overo-base.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-base.dtsi
@@ -30,6 +30,24 @@
                ti,codec = <&twl_audio>;
        };
 
+       /* HS USB Port 2 Power */
+       hsusb2_power: hsusb2_power_reg {
+               compatible = "regulator-fixed";
+               regulator-name = "hsusb2_vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&gpio6 8 0>;                            /* gpio_168: vbus enable */
+               startup-delay-us = <70000>;
+               enable-active-high;
+       };
+
+       /* HS USB Host PHY on PORT 2 */
+       hsusb2_phy: hsusb2_phy {
+               compatible = "usb-nop-xceiv";
+               reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;      /* gpio_183 */
+               vcc-supply = <&hsusb2_power>;
+       };
+
        /* Regulator to trigger the nPoweron signal of the Wifi module */
        w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
                compatible = "regulator-fixed";
@@ -64,6 +82,11 @@
 };
 
 &omap3_pmx_core {
+       pinctrl-names = "default";
+       pinctrl-0 = <
+                       &hsusb2_pins
+       >;
+
        uart2_pins: pinmux_uart2_pins {
                pinctrl-single,pins = <
                        OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)        /* mcbsp3_dx.uart2_cts */
@@ -116,6 +139,19 @@
                        OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)               /* uart3_rts_sd.gpio_164 */
                >;
        };
+
+       hsusb2_pins: pinmux_hsusb2_pins {
+               pinctrl-single,pins = <
+                       OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
+                       OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
+                       OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_simo.hsusb2_data4 */
+                       OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_somi.hsusb2_data5 */
+                       OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs0.hsusb2_data6 */
+                       OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs1.hsusb2_data3 */
+                       OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)               /* i2c2_scl.gpio_168 */
+                       OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4)               /* i2c2_sda.gpio_183 */
+               >;
+       };
 };
 
 &i2c1 {
@@ -177,6 +213,14 @@
        power = <50>;
 };
 
+&usbhshost {
+       port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+       phys = <0 &hsusb2_phy>;
+};
+
 &uart2 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart2_pins>;