Atmel: move console default platform_device to serial driver

[mv-sheeva.git] / arch / arm / mach-at91 / at91sam9rl_devices.c

diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 61908dce978447156f557866055fe93da689fe52..eda72e83037dc7dd176c859e7f4ad874a9506a75 100644 (file)
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -20,6 +20,7 @@
 #include <mach/board.h>
 #include <mach/at91sam9rl.h>
 #include <mach/at91sam9rl_matrix.h>
+#include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at_hdmac.h>
 
@@ -33,10 +34,6 @@
 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
 
-static struct at_dma_platform_data atdma_pdata = {
-       .nr_channels    = 2,
-};
-
 static struct resource hdmac_resources[] = {
        [0] = {
                .start  = AT91SAM9RL_BASE_DMA,
@@ -51,12 +48,11 @@ static struct resource hdmac_resources[] = {
 };
 
 static struct platform_device at_hdmac_device = {
-       .name           = "at_hdmac",
+       .name           = "at91sam9rl_dma",
        .id             = -1,
        .dev            = {
                                .dma_mask               = &hdmac_dmamask,
                                .coherent_dma_mask      = DMA_BIT_MASK(32),
-                               .platform_data          = &atdma_pdata,
        },
        .resource       = hdmac_resources,
        .num_resources  = ARRAY_SIZE(hdmac_resources),
@@ -64,7 +60,6 @@ static struct platform_device at_hdmac_device = {
 
 void __init at91_add_device_hdmac(void)
 {
-       dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
        platform_device_register(&at_hdmac_device);
 }
 #else
@@ -271,8 +266,8 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
        if (!data)
                return;
 
-       csa = at91_sys_read(AT91_MATRIX_EBICSA);
-       at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
+       csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+       at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
        /* enable pin */
        if (gpio_is_valid(data->enable_pin))
@@ -688,6 +683,8 @@ static struct resource rtt_resources[] = {
                .start  = AT91SAM9RL_BASE_RTT,
                .end    = AT91SAM9RL_BASE_RTT + SZ_16 - 1,
                .flags  = IORESOURCE_MEM,
+       }, {
+               .flags  = IORESOURCE_MEM,
        }
 };
 
@@ -695,11 +692,32 @@ static struct platform_device at91sam9rl_rtt_device = {
        .name           = "at91_rtt",
        .id             = 0,
        .resource       = rtt_resources,
-       .num_resources  = ARRAY_SIZE(rtt_resources),
 };
 
+#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
+static void __init at91_add_device_rtt_rtc(void)
+{
+       at91sam9rl_rtt_device.name = "rtc-at91sam9";
+       /*
+        * The second resource is needed:
+        * GPBR will serve as the storage for RTC time offset
+        */
+       at91sam9rl_rtt_device.num_resources = 2;
+       rtt_resources[1].start = AT91SAM9RL_BASE_GPBR +
+                                4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
+       rtt_resources[1].end = rtt_resources[1].start + 3;
+}
+#else
+static void __init at91_add_device_rtt_rtc(void)
+{
+       /* Only one resource is needed: RTT not used as RTC */
+       at91sam9rl_rtt_device.num_resources = 1;
+}
+#endif
+
 static void __init at91_add_device_rtt(void)
 {
+       at91_add_device_rtt_rtc();
        platform_device_register(&at91sam9rl_rtt_device);
 }
 
@@ -1134,7 +1152,6 @@ static inline void configure_usart3_pins(unsigned pins)
 }
 
 static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];  /* the UARTs to use */
-struct platform_device *atmel_default_console_device;  /* the serial console device */
 
 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
 {