Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...

[mv-sheeva.git] / arch / arm / mach-at91 / board-sam9263ek.c

diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index bccdcf23caa106e392dba97fa4df69f9775a5337..29f66052fe63b57d275cc40ae694b1f0199b83bf 100644 (file)
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
        .ports          = 2,
        .vbus_pin       = { AT91_PIN_PA24, AT91_PIN_PA21 },
+       .overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
        .vbus_pin       = AT91_PIN_PA25,
-       .pullup_pin     = 0,            /* pull-up driven by UDC */
+       .pullup_pin     = -EINVAL,              /* pull-up driven by UDC */
 };
 
 
@@ -151,14 +152,14 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
        .wire4          = 1,
        .det_pin        = AT91_PIN_PE18,
        .wp_pin         = AT91_PIN_PE19,
-//     .vcc_pin        = ... not connected
+       .vcc_pin        = -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
        .phy_irq_pin    = AT91_PIN_PE31,
        .is_rmii        = 1,
 };
@@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
        .ale            = 21,
        .cle            = 22,
-//     .det_pin        = ... not connected
+       .det_pin        = -EINVAL,
        .rdy_pin        = AT91_PIN_PA22,
        .enable_pin     = AT91_PIN_PD15,
        .parts          = ek_nand_partition,
@@ -218,7 +219,7 @@ static void __init ek_add_device_nand(void)
                ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
        /* configure chip-select 3 (NAND) */
-       sam9_smc_configure(3, &ek_nand_smc_config);
+       sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
        at91_add_device_nand(&ek_nand_data);
 }
@@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+       .reset_pin      = -EINVAL,
 };