#include <mach/clps711x.h>
-#define CLPS711X_VIRT_BASE IOMEM(0xff000000)
+#define IO_ADDRESS(x) (0xdc000000 + (((x) & 0x03ffffff) | \
+ (((x) >> 2) & 0x3c000000)))
+
+#define CLPS711X_VIRT_BASE IOMEM(IO_ADDRESS(CLPS711X_PHYS_BASE))
#ifndef __ASSEMBLY__
#define clps_readb(off) readb(CLPS711X_VIRT_BASE + (off))
#define CS7_PHYS_BASE (0x00000000)
#endif
-#define SYSPLD_VIRT_BASE 0xfe000000
-#define SYSPLD_BASE SYSPLD_VIRT_BASE
-
#if defined (CONFIG_ARCH_CDB89712)
-#define ETHER_START 0x20000000
-#define ETHER_SIZE 0x1000
-#define ETHER_BASE 0xfe000000
+#define ETHER_PHYS_BASE CS2_PHYS_BASE
+#define ETHER_SIZE 0x1000
#endif
#if defined (CONFIG_ARCH_EDB7211)
-/*
- * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3)
- * and repeat across it. This is the mapping for it.
- *
- * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This
- * was cause for much consternation and headscratching. This should probably
- * be made a compile/run time kernel option.
- */
-#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE /* physical */
-
-#define EP7211_VIRT_EXTKBD (0xfd000000) /* virtual */
-
-
-/*
- * The CS8900A ethernet chip has its I/O registers wired to chip select 2
- * (nCS2). This is the mapping for it.
- *
- * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This
- * was cause for much consternation and headscratching. This should probably
- * be made a compile/run time kernel option.
- */
-#define EP7211_PHYS_CS8900A CS2_PHYS_BASE /* physical */
-
-#define EP7211_VIRT_CS8900A (0xfc000000) /* virtual */
+/* The extra 8 lines of the keyboard matrix are wired to chip select 3 */
+#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE
+/* The CS8900A ethernet chip has its I/O registers wired to chip select 2 */
+#define EP7211_PHYS_CS8900A CS2_PHYS_BASE
-/*
- * The two flash banks are wired to chip selects 0 and 1. This is the mapping
- * for them.
- *
- * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
- * in jumpered boot mode.
- */
-#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE /* physical */
-#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE /* physical */
-
-#define EP7211_VIRT_FLASH1 (0xfa000000) /* virtual */
-#define EP7211_VIRT_FLASH2 (0xfb000000) /* virtual */
+/* The two flash banks are wired to chip selects 0 and 1 */
+#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE
+#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE
#endif /* CONFIG_ARCH_EDB7211 */