* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
+#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/spi/spi.h>
#include <linux/platform_device.h>
#include <linux/types.h>
+#include <linux/usb/otg.h>
+
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/imx-uart.h>
#include <mach/iomux-mx3.h>
#include <mach/mmc.h>
+#include <mach/mxc_ehci.h>
+#include <mach/ulpi.h>
+
+#include <media/soc_camera.h>
#include "devices.h"
MX31_PIN_PC_CD2_B__SD2_CLK, MX31_PIN_PC_CD1_B__SD2_CMD,
MX31_PIN_ATA_DIOR__GPIO3_28, MX31_PIN_ATA_DIOW__GPIO3_29,
/* CSI */
- MX31_PIN_CSI_D4__CSI_D4, MX31_PIN_CSI_D5__CSI_D5,
MX31_PIN_CSI_D6__CSI_D6, MX31_PIN_CSI_D7__CSI_D7,
MX31_PIN_CSI_D8__CSI_D8, MX31_PIN_CSI_D9__CSI_D9,
MX31_PIN_CSI_D10__CSI_D10, MX31_PIN_CSI_D11__CSI_D11,
MX31_PIN_CSI_D14__CSI_D14, MX31_PIN_CSI_D15__CSI_D15,
MX31_PIN_CSI_HSYNC__CSI_HSYNC, MX31_PIN_CSI_MCLK__CSI_MCLK,
MX31_PIN_CSI_PIXCLK__CSI_PIXCLK, MX31_PIN_CSI_VSYNC__CSI_VSYNC,
+ MX31_PIN_CSI_D4__GPIO3_4, MX31_PIN_CSI_D5__GPIO3_5,
MX31_PIN_GPIO3_0__GPIO3_0, MX31_PIN_GPIO3_1__GPIO3_1,
MX31_PIN_TXD2__GPIO1_28,
/* dsPIC resets */
MX31_PIN_STXD5__GPIO1_21, MX31_PIN_SRXD5__GPIO1_22,
+ /*battery detection */
+ MX31_PIN_LCS0__GPIO3_23,
+ /* USB H1 */
+ MX31_PIN_CSPI1_MISO__USBH1_RXDP, MX31_PIN_CSPI1_MOSI__USBH1_RXDM,
+ MX31_PIN_CSPI1_SS0__USBH1_TXDM, MX31_PIN_CSPI1_SS1__USBH1_TXDP,
+ MX31_PIN_CSPI1_SS2__USBH1_RCV, MX31_PIN_CSPI1_SCLK__USBH1_OEB,
+ MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, MX31_PIN_SFS6__USBH1_SUSPEND,
+ MX31_PIN_NFRE_B__GPIO1_11, MX31_PIN_NFALE__GPIO1_12,
};
#define SDHC2_CD IOMUX_TO_GPIO(MX31_PIN_ATA_DIOR)
}
}
+static struct spi_board_info marxbot_spi_board_info[] __initdata = {
+ {
+ .modalias = "spidev",
+ .max_speed_hz = 300000,
+ .bus_num = 1,
+ .chip_select = 1, /* according spi1_cs[] ! */
+ },
+};
+
+#define TURRETCAM_POWER IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)
+#define BASECAM_POWER IOMUX_TO_GPIO(MX31_PIN_CSI_D5)
+#define TURRETCAM_RST_B IOMUX_TO_GPIO(MX31_PIN_GPIO3_0)
+#define BASECAM_RST_B IOMUX_TO_GPIO(MX31_PIN_CSI_D4)
+#define CAM_CHOICE IOMUX_TO_GPIO(MX31_PIN_TXD2)
+
+static int marxbot_basecam_power(struct device *dev, int on)
+{
+ gpio_set_value(BASECAM_POWER, !on);
+ return 0;
+}
+
+static int marxbot_basecam_reset(struct device *dev)
+{
+ gpio_set_value(BASECAM_RST_B, 0);
+ udelay(100);
+ gpio_set_value(BASECAM_RST_B, 1);
+ return 0;
+}
+
+static struct i2c_board_info marxbot_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("mt9t031", 0x5d),
+ },
+};
+
+static struct soc_camera_link base_iclink = {
+ .bus_id = 0, /* Must match with the camera ID */
+ .power = marxbot_basecam_power,
+ .reset = marxbot_basecam_reset,
+ .board_info = &marxbot_i2c_devices[0],
+ .i2c_adapter_id = 0,
+ .module_name = "mt9t031",
+};
+
+static struct platform_device marxbot_camera[] = {
+ {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &base_iclink,
+ },
+ },
+};
+
+static struct platform_device *marxbot_cameras[] __initdata = {
+ &marxbot_camera[0],
+};
+
+static int __init marxbot_cam_init(void)
+{
+ int ret = gpio_request(CAM_CHOICE, "cam-choice");
+ if (ret)
+ return ret;
+ gpio_direction_output(CAM_CHOICE, 1);
+
+ ret = gpio_request(BASECAM_RST_B, "basecam-reset");
+ if (ret)
+ return ret;
+ gpio_direction_output(BASECAM_RST_B, 1);
+ ret = gpio_request(BASECAM_POWER, "basecam-standby");
+ if (ret)
+ return ret;
+ gpio_direction_output(BASECAM_POWER, 0);
+
+ ret = gpio_request(TURRETCAM_RST_B, "turretcam-reset");
+ if (ret)
+ return ret;
+ gpio_direction_output(TURRETCAM_RST_B, 1);
+ ret = gpio_request(TURRETCAM_POWER, "turretcam-standby");
+ if (ret)
+ return ret;
+ gpio_direction_output(TURRETCAM_POWER, 0);
+
+ return 0;
+}
+
+#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+static int marxbot_usbh1_hw_init(struct platform_device *pdev)
+{
+ mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true);
+
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SFS6, USB_PAD_CFG);
+
+ return 0;
+}
+
+#define USBH1_VBUSEN_B IOMUX_TO_GPIO(MX31_PIN_NFRE_B)
+#define USBH1_MODE IOMUX_TO_GPIO(MX31_PIN_NFALE)
+
+static int marxbot_isp1105_init(struct otg_transceiver *otg)
+{
+ int ret = gpio_request(USBH1_MODE, "usbh1-mode");
+ if (ret)
+ return ret;
+ /* single ended */
+ gpio_direction_output(USBH1_MODE, 0);
+
+ ret = gpio_request(USBH1_VBUSEN_B, "usbh1-vbusen");
+ if (ret) {
+ gpio_free(USBH1_MODE);
+ return ret;
+ }
+ gpio_direction_output(USBH1_VBUSEN_B, 1);
+
+ return 0;
+}
+
+
+static int marxbot_isp1105_set_vbus(struct otg_transceiver *otg, bool on)
+{
+ if (on)
+ gpio_set_value(USBH1_VBUSEN_B, 0);
+ else
+ gpio_set_value(USBH1_VBUSEN_B, 1);
+
+ return 0;
+}
+
+static struct mxc_usbh_platform_data usbh1_pdata = {
+ .init = marxbot_usbh1_hw_init,
+ .portsc = MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL,
+ .flags = MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_INTERFACE_SINGLE_UNI,
+};
+
+static int __init marxbot_usbh1_init(void)
+{
+ struct otg_transceiver *otg;
+
+ otg = kzalloc(sizeof(*otg), GFP_KERNEL);
+ if (!otg)
+ return -ENOMEM;
+
+ otg->label = "ISP1105";
+ otg->init = marxbot_isp1105_init;
+ otg->set_vbus = marxbot_isp1105_set_vbus;
+
+ usbh1_pdata.otg = otg;
+
+ return mxc_register_device(&mx31_usbh1, &usbh1_pdata);
+}
+
/*
* system init for baseboard usage. Will be called by mx31moboard init.
*/
dspics_resets_init();
mxc_register_device(&mxcsdhc_device1, &sdhc2_pdata);
+
+ spi_register_board_info(marxbot_spi_board_info,
+ ARRAY_SIZE(marxbot_spi_board_info));
+
+ marxbot_cam_init();
+ platform_add_devices(marxbot_cameras, ARRAY_SIZE(marxbot_cameras));
+
+ /* battery present pin */
+ gpio_request(IOMUX_TO_GPIO(MX31_PIN_LCS0), "bat-present");
+ gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_LCS0));
+ gpio_export(IOMUX_TO_GPIO(MX31_PIN_LCS0), false);
+
+ marxbot_usbh1_init();
}
projects / mv-sheeva.git / blobdiff