#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/input.h>
+#include <linux/usb/phy.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <asm/mach/arch.h>
#include <video/omapdss.h>
-#include <video/omap-panel-tfp410.h>
+#include <video/omap-panel-data.h>
#include <linux/platform_data/mtd-onenand-omap2.h>
#include "common.h"
static struct gpio_led igep_gpio_leds[] = {
[0] = {
- .name = "gpio-led:red:d0",
- .default_trigger = "default-off"
+ .name = "omap3:red:user0",
+ .default_state = 0,
},
[1] = {
- .name = "gpio-led:green:d0",
- .default_trigger = "default-off",
+ .name = "omap3:green:boot",
+ .default_state = 1,
},
[2] = {
- .name = "gpio-led:red:d1",
- .default_trigger = "default-off",
+ .name = "omap3:red:user1",
+ .default_state = 0,
},
[3] = {
- .name = "gpio-led:green:d1",
- .default_trigger = "heartbeat",
+ .name = "omap3:green:user1",
+ .default_state = 0,
.gpio = -EINVAL, /* gets replaced */
.active_low = 1,
},
omap3_pmic_init("twl4030", &igep_twldata);
}
-static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = {
- .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_phy_data igep2_phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = IGEP2_GPIO_USBH_NRESET,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
+static struct usbhs_phy_data igep3_phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = IGEP3_GPIO_USBH_NRESET,
+ .vcc_gpio = -EINVAL,
+ },
+};
- .phy_reset = true,
- .reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL,
+static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
};
-static const struct usbhs_omap_board_data igep3_usbhs_bdata __initconst = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
- .reset_gpio_port[2] = -EINVAL,
};
#ifdef CONFIG_OMAP_MUX
omap_serial_init();
omap_sdrc_init(m65kxxxxam_sdrc_params,
m65kxxxxam_sdrc_params);
+ usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
igep_flash_init();
igep_leds_init();
- omap_twl4030_audio_init("igep2");
+ omap_twl4030_audio_init("igep2", NULL);
/*
* WLAN-BT combo module from MuRata which has a Marvell WLAN
if (machine_is_igep0020()) {
omap_display_init(&igep2_dss_data);
igep2_init_smsc911x();
+ usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
usbhs_init(&igep2_usbhs_bdata);
} else {
+ usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
usbhs_init(&igep3_usbhs_bdata);
}
}
.handle_irq = omap3_intc_handle_irq,
.init_machine = igep_init,
.init_late = omap35xx_init_late,
- .timer = &omap3_timer,
+ .init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
.handle_irq = omap3_intc_handle_irq,
.init_machine = igep_init,
.init_late = omap35xx_init_late,
- .timer = &omap3_timer,
+ .init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END