#include <asm/dma.h>
#include <asm/timer.h>
#include <asm/i8259.h>
-#include <asm/nmi.h>
#include <asm/msidef.h>
#include <asm/hypertransport.h>
#include <asm/setup.h>
}
early_param("noapic", parse_noapic);
+/* Will be called in mpparse/acpi/sfi codes for saving IRQ info */
+void mp_save_irq(struct mpc_intsrc *m)
+{
+ int i;
+
+ apic_printk(APIC_VERBOSE, "Int: type %d, pol %d, trig %d, bus %02x,"
+ " IRQ %02x, APIC ID %x, APIC INT %02x\n",
+ m->irqtype, m->irqflag & 3, (m->irqflag >> 2) & 3, m->srcbus,
+ m->srcbusirq, m->dstapic, m->dstirq);
+
+ for (i = 0; i < mp_irq_entries; i++) {
+ if (!memcmp(&mp_irqs[i], m, sizeof(*m)))
+ return;
+ }
+
+ memcpy(&mp_irqs[mp_irq_entries], m, sizeof(*m));
+ if (++mp_irq_entries == MAX_IRQ_SOURCES)
+ panic("Max # of irq sources exceeded!!\n");
+}
+
struct irq_pin_list {
int apic, pin;
struct irq_pin_list *next;
return kzalloc_node(sizeof(struct irq_pin_list), GFP_KERNEL, node);
}
+
/* irq_cfg is indexed by the sum of all RTEs in all I/O APICs. */
#ifdef CONFIG_SPARSE_IRQ
static struct irq_cfg irq_cfgx[NR_IRQS_LEGACY];
= mp_ioapics[apic_id].apicid;
/*
- * Read the right value from the MPC table and
- * write it into the ID register.
+ * Update the ID register according to the right value
+ * from the MPC table if they are different.
*/
+ if (mp_ioapics[apic_id].apicid == reg_00.bits.ID)
+ continue;
+
apic_printk(APIC_VERBOSE, KERN_INFO
"...changing IO-APIC physical APIC ID to %d ...",
mp_ioapics[apic_id].apicid);
unsigned int irr;
struct irq_desc *desc;
struct irq_cfg *cfg;
- irq = __get_cpu_var(vector_irq)[vector];
+ irq = __this_cpu_read(vector_irq[vector]);
if (irq == -1)
continue;
apic->send_IPI_self(IRQ_MOVE_CLEANUP_VECTOR);
goto unlock;
}
- __get_cpu_var(vector_irq)[vector] = -1;
+ __this_cpu_write(vector_irq[vector], -1);
unlock:
raw_spin_unlock(&desc->lock);
}
"edge");
}
-static void __init setup_nmi(void)
-{
- /*
- * Dirty trick to enable the NMI watchdog ...
- * We put the 8259A master into AEOI mode and
- * unmask on all local APICs LVT0 as NMI.
- *
- * The idea to use the 8259A in AEOI mode ('8259A Virtual Wire')
- * is from Maciej W. Rozycki - so we do not have to EOI from
- * the NMI handler or the timer interrupt.
- */
- apic_printk(APIC_VERBOSE, KERN_INFO "activating NMI Watchdog ...");
-
- enable_NMI_through_LVT0();
-
- apic_printk(APIC_VERBOSE, " done.\n");
-}
-
/*
* This looks a bit hackish but it's about the only one way of sending
* a few INTA cycles to 8259As and any associated glue logic. ICR does
*/
apic_write(APIC_LVT0, APIC_LVT_MASKED | APIC_DM_EXTINT);
legacy_pic->init(1);
-#ifdef CONFIG_X86_32
- {
- unsigned int ver;
-
- ver = apic_read(APIC_LVR);
- ver = GET_APIC_VERSION(ver);
- timer_ack = (nmi_watchdog == NMI_IO_APIC && !APIC_INTEGRATED(ver));
- }
-#endif
pin1 = find_isa_irq_pin(0, mp_INT);
apic1 = find_isa_irq_apic(0, mp_INT);
unmask_ioapic(cfg);
}
if (timer_irq_works()) {
- if (nmi_watchdog == NMI_IO_APIC) {
- setup_nmi();
- legacy_pic->unmask(0);
- }
if (disable_timer_pin_1 > 0)
clear_IO_APIC_pin(0, pin1);
goto out;
if (timer_irq_works()) {
apic_printk(APIC_QUIET, KERN_INFO "....... works.\n");
timer_through_8259 = 1;
- if (nmi_watchdog == NMI_IO_APIC) {
- legacy_pic->mask(0);
- setup_nmi();
- legacy_pic->unmask(0);
- }
goto out;
}
/*
apic_printk(APIC_QUIET, KERN_INFO "....... failed.\n");
}
- if (nmi_watchdog == NMI_IO_APIC) {
- apic_printk(APIC_QUIET, KERN_WARNING "timer doesn't work "
- "through the IO-APIC - disabling NMI Watchdog!\n");
- nmi_watchdog = NMI_NONE;
- }
-#ifdef CONFIG_X86_32
- timer_ack = 0;
-#endif
-
apic_printk(APIC_QUIET, KERN_INFO
"...trying to set up timer as Virtual Wire IRQ...\n");
printk(KERN_INFO "Early APIC setup for system timer0\n");
#ifndef CONFIG_SMP
- phys_cpu_present_map = physid_mask_of_physid(boot_cpu_physical_apicid);
+ physid_set_mask_of_physid(boot_cpu_physical_apicid,
+ &phys_cpu_present_map);
#endif
/* Make sure the irq descriptor is set up */
cfg = alloc_irq_and_cfg_at(0, 0);