#include <common.h>
#include <libfdt.h>
#include <fdt_support.h>
-#include <ppc4xx.h>
-#include <asm/gpio.h>
+#include <asm/ppc4xx.h>
+#include <asm/ppc4xx-gpio.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/bitops.h>
extern void __ft_board_setup(void *blob, bd_t *bd);
ulong flash_get_size(ulong base, int banknum);
+static inline u32 get_async_pci_freq(void)
+{
+ if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
+ CONFIG_SYS_BCSR5_PCI66EN)
+ return 66666666;
+ else
+ return 33333333;
+}
+
int board_early_init_f(void)
{
u32 sdr0_cust0;
/*
* Setup the interrupt controller polarities, triggers, etc.
*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */
- mtdcr(uic0pr, 0xfffff7ff); /* per ref-board manual */
- mtdcr(uic0tr, 0x00000000); /* per ref-board manual */
- mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffffff); /* per ref-board manual */
- mtdcr(uic1tr, 0x00000000); /* per ref-board manual */
- mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
-
- mtdcr(uic2sr, 0xffffffff); /* clear all */
- mtdcr(uic2er, 0x00000000); /* disable all */
- mtdcr(uic2cr, 0x00000000); /* all non-critical */
- mtdcr(uic2pr, 0xffffffff); /* per ref-board manual */
- mtdcr(uic2tr, 0x00000000); /* per ref-board manual */
- mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */
- mtdcr(uic2sr, 0xffffffff); /* clear all */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000005); /* ATI & UIC1 crit are critical */
+ mtdcr(UIC0PR, 0xfffff7ff); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+ mtdcr(UIC2ER, 0x00000000); /* disable all */
+ mtdcr(UIC2CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC2PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC2TR, 0x00000000); /* per ref-board manual */
+ mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */
+ mtdcr(UIC2SR, 0xffffffff); /* clear all */
+
+ /* Check and reconfigure the PCI sync clock if necessary */
+ ppc4xx_pci_sync_clock_config(get_async_pci_freq());
/* 50MHz tmrclk */
out_8((u8 *) CONFIG_SYS_BCSR_BASE + 0x04, 0x00);
{
char *s = getenv("serial#");
u8 rev;
- u8 val;
+ u32 clock = get_async_pci_freq();
#ifdef CONFIG_440EPX
printf("Board: Sequoia - AMCC PPC440EPx Evaluation Board");
#endif
rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
- val = in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) & CONFIG_SYS_BCSR5_PCI66EN;
- printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
+ printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
if (s != NULL) {
puts(", serial# ");
}
putc('\n');
+ /*
+ * Reconfiguration of the PCI sync clock is already done,
+ * now check again if everything is in range:
+ */
+ if (ppc4xx_pci_sync_clock_config(clock)) {
+ printf("ERROR: PCI clocking incorrect (async=%d "
+ "sync=%ld)!\n", clock, get_PCI_freq());
+ }
+
return (0);
}
/*
* Assign interrupts to PCI devices.
*/
-void sequoia_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#ifdef CONFIG_PCI_PNP
- hose->fixup_irq = sequoia_pci_fixup_irq;
-#endif
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
-/*
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- */
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Cactus is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
-#if defined(CONFIG_POST)
-/*
- * Returns 1 if keys pressed to start the power-on long-running tests
- * Called from board_init_f().
- */
-int post_hotkeys_pressed(void)
-{
- return 0; /* No hotkeys supported */
-}
-#endif /* CONFIG_POST */
-
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
/*
* On NAND-booting sequoia, we need to patch the chips select numbers
projects / karo-tx-uboot.git / blobdiff