#include <common.h>
#include <ppc4xx.h>
#include <i2c.h>
+#include <netdev.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/4xx_pcie.h>
| 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
|
+-------------------------------------------------------------------*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_16PERCLK |
EBC_CFG_ATC_PREVIOUS |
| boot type
|
+-------------------------------------------------------------------*/
- mtebc(pb1ap, EBC_BXAP_FPGA);
- mtebc(pb1cr, EBC_BXCR_FPGA_CS1);
+ mtebc(PB1AP, EBC_BXAP_FPGA);
+ mtebc(PB1CR, EBC_BXCR_FPGA_CS1);
/*-------------------------------------------------------------------+
|
break;
}
- mtebc(pb0ap, ebc0_cs0_bxap_value);
- mtebc(pb0cr, ebc0_cs0_bxcr_value);
- mtebc(pb2ap, ebc0_cs2_bxap_value);
- mtebc(pb2cr, ebc0_cs2_bxcr_value);
+ mtebc(PB0AP, ebc0_cs0_bxap_value);
+ mtebc(PB0CR, ebc0_cs0_bxcr_value);
+ mtebc(PB2AP, ebc0_cs2_bxap_value);
+ mtebc(PB2CR, ebc0_cs2_bxcr_value);
/*--------------------------------------------------------------------+
| Interrupt controller setup for the AMCC 440SPe Evaluation board.
mtdcr (uic0sr, 0x00000000); /* clear all interrupts */
mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */
- mfsdr(sdr_mfr, mfr);
+ mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
- mtsdr(sdr_mfr, mfr);
+ mtsdr(SDR0_MFR, mfr);
fpga_init();
* The yucca board is always configured as the host & requires the
* PCI arbiter to be enabled.
*-------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
* may not be sufficient for a given board.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller * hose )
{
/*-------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
*-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+ out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
out32r( PCIX0_PIM0LAH, 0 );
out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
out32r( PCIX0_BAR0, 0 );
/*-------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*-------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+ out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
#if defined(CONFIG_PCI)
/*************************************************************************
return 1;
}
-int yucca_pcie_card_present(int port)
+static int yucca_pcie_card_present(int port)
{
u16 reg;
/* setup mem resource */
pci_set_region(hose->regions + 0,
- CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
- CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
- CFG_PCIE_MEMSIZE,
+ CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
+ CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
+ CONFIG_SYS_PCIE_MEMSIZE,
PCI_REGION_MEM);
hose->region_count = 1;
pci_register_hose(hose);
int misc_init_f (void)
{
uint reg;
-#if defined(CONFIG_STRESS)
- uint i ;
- uint disp;
-#endif
out16(FPGA_REG10, (in16(FPGA_REG10) &
~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) |
/* minimal init for PCIe */
/* pci express 0 Endpoint Mode */
- mfsdr(SDR0_PE0DLPSET, reg);
+ mfsdr(SDRN_PESDR_DLPSET(0), reg);
reg &= (~0x00400000);
- mtsdr(SDR0_PE0DLPSET, reg);
+ mtsdr(SDRN_PESDR_DLPSET(0), reg);
/* pci express 1 Rootpoint Mode */
- mfsdr(SDR0_PE1DLPSET, reg);
+ mfsdr(SDRN_PESDR_DLPSET(1), reg);
reg |= 0x00400000;
- mtsdr(SDR0_PE1DLPSET, reg);
+ mtsdr(SDRN_PESDR_DLPSET(1), reg);
/* pci express 2 Rootpoint Mode */
- mfsdr(SDR0_PE2DLPSET, reg);
+ mfsdr(SDRN_PESDR_DLPSET(2), reg);
reg |= 0x00400000;
- mtsdr(SDR0_PE2DLPSET, reg);
+ mtsdr(SDRN_PESDR_DLPSET(2), reg);
out16(FPGA_REG1C,(in16 (FPGA_REG1C) &
~FPGA_REG1C_PE0_ROOTPOINT &
~FPGA_REG1C_PE1_ENDPOINT &
~FPGA_REG1C_PE2_ENDPOINT));
-#if defined(CONFIG_STRESS)
- /*
- * all this setting done by linux only needed by stress an charac. test
- * procedure
- * PCIe 1 Rootpoint PCIe2 Endpoint
- * PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver
- * Power Level
- */
- for (i = 0, disp = 0; i < 8; i++, disp += 3) {
- mfsdr(SDR0_PE0HSSSET1L0 + disp, reg);
- reg |= 0x33000000;
- mtsdr(SDR0_PE0HSSSET1L0 + disp, reg);
- }
-
- /*
- * PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver
- * Power Level
- */
- for (i = 0, disp = 0; i < 4; i++, disp += 3) {
- mfsdr(SDR0_PE1HSSSET1L0 + disp, reg);
- reg |= 0x33000000;
- mtsdr(SDR0_PE1HSSSET1L0 + disp, reg);
- }
-
- /*
- * PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver
- * Power Level
- */
- for (i = 0, disp = 0; i < 4; i++, disp += 3) {
- mfsdr(SDR0_PE2HSSSET1L0 + disp, reg);
- reg |= 0x33000000;
- mtsdr(SDR0_PE2HSSSET1L0 + disp, reg);
- }
-
- reg = 0x21242222;
- mtsdr(SDR0_PE2UTLSET1, reg);
- reg = 0x11000000;
- mtsdr(SDR0_PE2UTLSET2, reg);
- /* pci express 1 Endpoint Mode */
- reg = 0x00004000;
- mtsdr(SDR0_PE2DLPSET, reg);
-
- mtsdr(SDR0_UART1, 0x2080005a); /* patch for TG */
-#endif
return 0;
}
#endif
return (BOARD_OPTION_NOT_SELECTED);
}
+
+int board_eth_init(bd_t *bis)
+{
+ cpu_eth_init(bis);
+ return pci_eth_init(bis);
+}
projects / karo-tx-uboot.git / blobdiff