* (C) Copyright 2007-2008
* Larry Johnson, lrj@acm.org
*
- * (C) Copyright 2006-2008
+ * (C) Copyright 2006-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2006
* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
- * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
+ * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
*/
#include <common.h>
+#include <fdt_support.h>
#include <i2c.h>
+#include <libfdt.h>
#include <ppc440.h>
+#include <asm/bitops.h>
#include <asm/gpio.h>
-#include <asm/processor.h>
#include <asm/io.h>
-#include <asm/bitops.h>
+#include <asm/ppc4xx-uic.h>
+#include <asm/processor.h>
DECLARE_GLOBAL_DATA_PTR;
ulong flash_get_size(ulong base, int banknum);
+#if defined(CONFIG_KORAT_PERMANENT)
+void korat_buzzer(int const on)
+{
+ if (on) {
+ out_8((u8 *) CFG_CPLD_BASE + 0x05,
+ in_8((u8 *) CFG_CPLD_BASE + 0x05) | 0x80);
+ } else {
+ out_8((u8 *) CFG_CPLD_BASE + 0x05,
+ in_8((u8 *) CFG_CPLD_BASE + 0x05) & ~0x80);
+ }
+}
+#endif
+
int board_early_init_f(void)
{
- u32 sdr0_pfc1, sdr0_pfc2;
- u32 reg;
+ uint32_t sdr0_pfc1, sdr0_pfc2;
+ uint32_t reg;
int eth;
+#if defined(CONFIG_KORAT_PERMANENT)
+ unsigned mscount;
+
+ extern void korat_branch_absolute(uint32_t addr);
+
+ for (mscount = 0; mscount < CFG_KORAT_MAN_RESET_MS; ++mscount) {
+ udelay(1000);
+ if (gpio_read_in_bit(CFG_GPIO_RESET_PRESSED_)) {
+ /* This call does not return. */
+ korat_branch_absolute(
+ CFG_FLASH1_TOP - 2 * CONFIG_ENV_SECT_SIZE - 4);
+ }
+ }
+ korat_buzzer(1);
+ while (!gpio_read_in_bit(CFG_GPIO_RESET_PRESSED_))
+ udelay(1000);
+
+ korat_buzzer(0);
+#endif
+
mtdcr(ebccfga, xbcfg);
mtdcr(ebccfgd, 0xb8400000);
mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */
mtdcr(uic2sr, 0xffffffff); /* clear all */
- /* take sim card reader and CF controller out of reset */
- out_8((u8 *) CFG_CPLD_BASE + 0x04, 0x80);
+ /*
+ * Take sim card reader and CF controller out of reset. Also enable PHY
+ * auto-detect until board-specific PHY resets are available.
+ */
+ out_8((u8 *) CFG_CPLD_BASE + 0x02, 0xC0);
/* Configure the two Ethernet PHYs. For each PHY, configure for fiber
* if the SFP module is present, and for copper if it is not present.
if (gpio_read_in_bit(CFG_GPIO_SFP0_PRESENT_ + eth)) {
/* SFP module not present: configure PHY for copper. */
/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
- out_8((u8 *) CFG_CPLD_BASE + 0x06,
- in_8((u8 *) CFG_CPLD_BASE + 0x06) |
+ out_8((u8 *) CFG_CPLD_BASE + 0x03,
+ in_8((u8 *) CFG_CPLD_BASE + 0x03) |
0x06 << (4 * eth));
} else {
/* SFP module present: configure PHY for fiber and
gpio_write_bit(CFG_GPIO_PHY0_EN, 1);
gpio_write_bit(CFG_GPIO_PHY1_EN, 1);
- /* select Ethernet pins */
+ /* Wait 1 ms, then enable Fiber signal detect to PHYs. */
+ udelay(1000);
+ out_8((u8 *) CFG_CPLD_BASE + 0x03,
+ in_8((u8 *) CFG_CPLD_BASE + 0x03) | 0x88);
+
+ /* select Ethernet (and optionally IIC1) pins */
mfsdr(SDR0_PFC1, sdr0_pfc1);
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
SDR0_PFC1_SELECT_CONFIG_4;
+#ifdef CONFIG_I2C_MULTI_BUS
+ sdr0_pfc1 |= ((sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL);
+#endif
mfsdr(SDR0_PFC2, sdr0_pfc2);
sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
SDR0_PFC2_SELECT_CONFIG_4;
return 0;
}
+/*
+ * The boot flash on CS0 normally has its write-enable pin disabled, and so will
+ * not respond to CFI commands. This routine therefore fills in the flash
+ * information for the boot flash. (The flash at CS1 operates normally.)
+ */
+ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t * info)
+{
+ uint32_t addr;
+ int i;
+
+ if (1 != banknum)
+ return 0;
+
+ info->size = CFG_FLASH0_SIZE;
+ info->sector_count = CFG_FLASH0_SIZE / 0x20000;
+ info->flash_id = 0x01000000;
+ info->portwidth = 2;
+ info->chipwidth = 2;
+ info->buffer_size = 32;
+ info->erase_blk_tout = 16384;
+ info->write_tout = 2;
+ info->buffer_write_tout = 5;
+ info->vendor = 2;
+ info->cmd_reset = 0x00F0;
+ info->interface = 2;
+ info->legacy_unlock = 0;
+ info->manufacturer_id = 1;
+ info->device_id = 0x007E;
+
+#if CFG_FLASH0_SIZE == 0x01000000
+ info->device_id2 = 0x2101;
+#elif CFG_FLASH0_SIZE == 0x04000000
+ info->device_id2 = 0x2301;
+#else
+#error Unable to set device_id2 for current CFG_FLASH0_SIZE
+#endif
+
+ info->ext_addr = 0x0040;
+ info->cfi_version = 0x3133;
+ info->cfi_offset = 0x0055;
+ info->addr_unlock1 = 0x00000555;
+ info->addr_unlock2 = 0x000002AA;
+ info->name = "CFI conformant";
+ for (i = 0, addr = -info->size;
+ i < info->sector_count;
+ ++i, addr += 0x20000) {
+ info->start[i] = addr;
+ info->protect[i] = 0x00;
+ }
+ return 1;
+}
+
static int man_data_read(unsigned int addr)
{
/*
* If the environmental variable "serial#" is not set, try to set it
* from the manufacturer's information serial EEPROM.
*/
- char s[MAN_SERIAL_NO_LENGTH + 1];
+ char s[MAN_INFO_LENGTH + MAN_MAC_ADDR_LENGTH + 2];
+
+ if (getenv("serial#"))
+ return;
- if (0 == getenv("serial#") &&
- 0 != man_data_read_field(s, MAN_SERIAL_NO_FIELD,
- MAN_SERIAL_NO_LENGTH))
- setenv("serial#", s);
+ if (!man_data_read_field(s, MAN_INFO_FIELD, MAN_INFO_LENGTH))
+ return;
+
+ s[MAN_INFO_LENGTH] = '-';
+ if (!man_data_read_field(s + MAN_INFO_LENGTH + 1, MAN_MAC_ADDR_FIELD,
+ MAN_MAC_ADDR_LENGTH))
+ return;
+
+ setenv("serial#", s);
}
static void set_mac_addresses(void)
* set, try to set them from the manufacturer's information serial
* EEPROM.
*/
- char s[MAN_MAC_ADDR_LENGTH + 1];
+
+#if MAN_MAC_ADDR_LENGTH % 2 != 0
+#error MAN_MAC_ADDR_LENGTH must be an even number
+#endif
+
+ char s[(3 * MAN_MAC_ADDR_LENGTH) / 2];
+ char *src;
+ char *dst;
if (0 != getenv("ethaddr") && 0 != getenv("eth1addr"))
return;
- if (0 == man_data_read_field(s, MAN_MAC_ADDR_FIELD,
- MAN_MAC_ADDR_LENGTH))
+ if (0 == man_data_read_field(s + (MAN_MAC_ADDR_LENGTH / 2) - 1,
+ MAN_MAC_ADDR_FIELD, MAN_MAC_ADDR_LENGTH))
return;
+ for (src = s + (MAN_MAC_ADDR_LENGTH / 2) - 1, dst = s; src != dst;) {
+ *dst++ = *src++;
+ *dst++ = *src++;
+ *dst++ = ':';
+ }
if (0 == getenv("ethaddr"))
setenv("ethaddr", s);
if (0 == getenv("eth1addr")) {
- ++s[MAN_MAC_ADDR_LENGTH - 1];
+ ++s[((3 * MAN_MAC_ADDR_LENGTH) / 2) - 2];
setenv("eth1addr", s);
}
}
int misc_init_r(void)
{
- uint pbcr;
- int size_val = 0;
- u32 reg;
+ uint32_t pbcr;
+ int size_val;
+ uint32_t reg;
unsigned long usb2d0cr = 0;
unsigned long usb2phy0cr, usb2h0cr = 0;
unsigned long sdr0_pfc1;
- char *act = getenv("usbact");
-
- /* Re-do flash sizing to get full correct info */
+ uint32_t const flash1_size = gd->bd->bi_flashsize - CFG_FLASH0_SIZE;
+ char const *const act = getenv("usbact");
- /* adjust flash start and offset */
- gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+ /*
+ * Re-do FLASH1 sizing and adjust flash start and offset.
+ */
+ gd->bd->bi_flashstart = CFG_FLASH1_TOP - flash1_size;
gd->bd->bi_flashoffset = 0;
- mtdcr(ebccfga, pb0cr);
+ mtdcr(ebccfga, pb1cr);
pbcr = mfdcr(ebccfgd);
- size_val = ffs(gd->bd->bi_flashsize) - 21;
+ size_val = ffs(flash1_size) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(ebccfga, pb1cr);
mtdcr(ebccfgd, pbcr);
/*
*/
flash_get_size(gd->bd->bi_flashstart, 0);
- /* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET, -CFG_MONITOR_LEN, 0xffffffff,
- &flash_info[0]);
+ /*
+ * Re-do FLASH1 sizing and adjust flash offset to reserve space for
+ * environment
+ */
+ gd->bd->bi_flashoffset =
+ CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - CFG_FLASH1_ADDR;
+
+ mtdcr(ebccfga, pb1cr);
+ pbcr = mfdcr(ebccfgd);
+ size_val = ffs(gd->bd->bi_flashsize - CFG_FLASH0_SIZE) - 21;
+ pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
+ mtdcr(ebccfga, pb1cr);
+ mtdcr(ebccfgd, pbcr);
+ /* Monitor protection ON by default */
+#if defined(CONFIG_KORAT_PERMANENT)
+ (void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
+ CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+ flash_info + 1);
+#else
+ (void)flash_protect(FLAG_PROTECT_SET, CFG_MONITOR_BASE,
+ CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+ flash_info);
+#endif
/* Env protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND,
- CFG_ENV_ADDR_REDUND + 2 * CFG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
+ (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
+ CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
+ flash_info);
+ (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
+ flash_info);
/*
* USB suff...
set_serial_number();
set_mac_addresses();
+ gpio_write_bit(CFG_GPIO_ATMEGA_RESET_, 1);
+
return 0;
}
u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);
printf("Board: Korat, Rev. %X", rev);
- if (s != NULL)
+ if (s)
printf(", serial# %s", s);
- printf(", Ethernet PHY 0: ");
+ printf(".\n Ethernet PHY 0: ");
if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL))
printf("fiber");
else
printf("copper");
printf(".\n");
- return (0);
+#if defined(CONFIG_KORAT_PERMANENT)
+ printf(" Executing permanent copy of U-Boot.\n");
+#endif
+ return 0;
}
-#if defined(CFG_DRAM_TEST)
-int testdram(void)
+#if defined(CONFIG_PCI) && defined(CONFIG_PCI_PNP)
+/*
+ * Assign interrupts to PCI devices.
+ */
+void korat_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
- unsigned long *mem = (unsigned long *)0;
- const unsigned long kend = (1024 / sizeof(unsigned long));
- unsigned long k, n;
-
- mtmsr(0);
-
- /* TODO: find correct size of SDRAM */
- for (k = 0; k < CFG_MBYTES_SDRAM;
- ++k, mem += (1024 / sizeof(unsigned long))) {
- if ((k & 1023) == 0)
- printf("%3d MB\r", k / 1024);
-
- memset(mem, 0xaaaaaaaa, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0xaaaaaaaa) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
-
- memset(mem, 0x55555555, 1024);
- for (n = 0; n < kend; ++n) {
- if (mem[n] != 0x55555555) {
- printf("SDRAM test fails at: %08x\n",
- (uint) & mem[n]);
- return 1;
- }
- }
- }
- printf("SDRAM test passes\n");
- return 0;
+ pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
-#endif /* defined(CFG_DRAM_TEST) */
+#endif
/*
* pci_pre_init
addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
mtdcr(plb1_acr, addr);
+#if defined(CONFIG_PCI_PNP)
+ hose->fixup_irq = korat_pci_fixup_irq;
+#endif
+
return 1;
}
#endif /* defined(CONFIG_PCI) */
/*
* PowerPC440EPX PCI Master configuration.
* Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
+ * PLB address 0x80000000-0xBFFFFFFF
+ * ==> PCI address 0x80000000-0xBFFFFFFF
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM0PCILA,
+ CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM1LA,
+ CFG_PCI_MEMBASE + 0x20000000); /* PMM0 Local Address */
+ out32r(PCIX0_PMM1PCILA,
+ CFG_PCI_MEMBASE + 0x20000000); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
return 0; /* No hotkeys supported */
}
#endif /* CONFIG_POST */
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ u32 val[4];
+ int rc;
+
+ ft_cpu_setup(blob, bd);
+
+ /* Fixup NOR mapping */
+ val[0] = 1; /* chip select number */
+ val[1] = 0; /* always 0 */
+ val[2] = gd->bd->bi_flashstart;
+ val[3] = gd->bd->bi_flashsize - CFG_FLASH0_SIZE;
+ rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges",
+ val, sizeof(val), 1);
+ if (rc)
+ printf("Unable to update property NOR mapping, err=%s\n",
+ fdt_strerror(rc));
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
projects / karo-tx-uboot.git / blobdiff