*/
#include <common.h>
-#include <ppc4xx.h>
+#include <asm/ppc4xx.h>
#include <malloc.h>
#include <command.h>
#include <crc.h>
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
- * GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c
+ * GPIO's are alreay setup in arch/powerpc/cpu/ppc4xx/cpu_init.c
* via define from board config file.
*-------------------------------------------------------------------*/
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
- mtdcr(uic0sr, 0xffffffff); /* clear all */
- mtdcr(uic0er, 0x00000000); /* disable all */
- mtdcr(uic0cr, 0x00000001); /* UIC1 crit is critical */
- mtdcr(uic0pr, 0xfffffe1f); /* per ref-board manual */
- mtdcr(uic0tr, 0x01c00000); /* per ref-board manual */
- mtdcr(uic0vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic0sr, 0xffffffff); /* clear all */
-
- mtdcr(uic1sr, 0xffffffff); /* clear all */
- mtdcr(uic1er, 0x00000000); /* disable all */
- mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xffffe0ff); /* per ref-board manual */
- mtdcr(uic1tr, 0x00ffc000); /* per ref-board manual */
- mtdcr(uic1vr, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(uic1sr, 0xffffffff); /* clear all */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+ mtdcr(UIC0ER, 0x00000000); /* disable all */
+ mtdcr(UIC0CR, 0x00000001); /* UIC1 crit is critical */
+ mtdcr(UIC0PR, 0xfffffe1f); /* per ref-board manual */
+ mtdcr(UIC0TR, 0x01c00000); /* per ref-board manual */
+ mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC0SR, 0xffffffff); /* clear all */
+
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
+ mtdcr(UIC1ER, 0x00000000); /* disable all */
+ mtdcr(UIC1CR, 0x00000000); /* all non-critical */
+ mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
+ mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
+ mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
+ mtdcr(UIC1SR, 0xffffffff); /* clear all */
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00000000); /* Pin function: enable GPIO49-63 */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00000000); /* Pin function: enable GPIO49-63 */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
return 0;
}
load_ethaddr();
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
return dram_size;
}
-/*************************************************************************
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB3 devices to 0.
- | Set PLB3 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
-
- /*-------------------------------------------------------------------------+
- | Set priority for all PLB4 devices to 0.
- +-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
-
- /*-------------------------------------------------------------------------+
- | Set Nebula PLB4 arbiter to fair mode.
- +-------------------------------------------------------------------------*/
- /* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
-
- /* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
-
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
- * pci_master_init
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*--------------------------------------------------------------------------+
- | Write the PowerPC440 EP PCI Configuration regs.
- | Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- | Enable PowerPC440 EP to act as a PCI memory target (PTM).
- +--------------------------------------------------------------------------*/
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
-/*************************************************************************
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* PCS440EP is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
/*************************************************************************
* hw_watchdog_reset
*
* "led" Commando for the U-Boot shell
*
************************************************************************/
-int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int rcode = 0, i;
ulong pattern = 0;
* "sha1" Commando for the U-Boot shell
*
************************************************************************/
-int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int do_sha1 (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int rcode = -1;
if (argc < 2) {
- usage:
- cmd_usage(cmdtp);
- return 1;
+usage:
+ return cmd_usage(cmdtp);
}
if (argc >= 3) {
projects / karo-tx-uboot.git / blobdiff